Savonius Vertical Axis Wind Turbine Research Articles

Performance of a Savonius Vertical Axis Wind Turbine installed on a Forward Facing Step

This study investigates the effects of installing a Savonius turbine on a forward-facing step to increase the power efficiency. Since the flow is disturbed by the step, the turbine may benefit from the accelerated flow found on top of the step. The flow field is solved using Computational Fluid Dynamics in a 3D computational domain. The Finite Volume Method is used to solve the Reynolds Average Navier-Stokes governing equations and the SST k-ω turbulence equations. This simulation includes both rotating turbine and the step. The novelty of this work is to study this configuration with a power law wind velocity distribution as inlet velocity, which is more realistic in common applications, and to investigate a different turbine. The study shows that the Savonius turbine generates up to 73% more power when installed on a 5-meter step. However, in case of a very high step, or a different turbine no improvement has been observed.

Numerical study on aerodynamic performance improvement and efficiency enhancement of the savonius vertical axis wind turbine with semi-directional airfoil guide vane

The growth of greenhouse gases increased the need for wind energy resource. Savonius vertical axis wind turbines (VAWT) have high potential as a turbomachine. Optimization methods such as flow injection on the rotor suction side to flow control on buckets developed as Savonius VAWTs operating range and efficiency are lower than other VAWTs. In this study, the semi-directional airfoil guide vane (SDAGV) was introduced to improve the aerodynamic performance and increase the efficiency of Savonius VAWT. The results indicate that the vane installation at the lower upstream of the rotor yields a power coefficient (Cp) of 0.12, representing a 140% growth compared to a single Savonius rotor. Furthermore, this installation extended the operating range of the turbine from a tip speed ratio (TSR) of 0.51–0.8. According to the results, it was found that more passages could improve efficiency. Five types of symmetrical airfoil profiles were evaluated for the guide vane. The NACA0010 airfoil profile, which has lower thickness than the others, obtained 7% higher efficiency than the base case consisting of NACA0012. Also, the optimal stagger angle for configurations NACA0021, NACA0018 was found to be 45°, and for NACA0010 and NACA0012 was determined to be 30°, respectively.

Fatigue-Life Prediction of the Optimized Savonius Vertical-Axis Wind Turbine Composite Blades

Abstract The sustainability of modern human civilization is significantly concerned with enhancing sustainable energy resources. Vertical-Axis Wind Turbines (VAWTs) gained a promising impact on the global energy mix due to their belief in sustainable energy solutions. This paper presents an integrated study of the dynamic performance and fatigue-life characteristics of the optimized Savonius-rotor VAWT composite blades. Furthermore, this paper introduces an experimental validation, numerical modeling, and visualization/verification study of the optimized VAWT composite blades and assesses its impact on the whole performance of the optimized Savonius VAWTs. Four combination levels of the optimal settings of the S-VAWT composite blade configurations are designed, modeled, simulated, and fabricated of Carbon/Glass—Polyester. The modal parameters such as natural frequency, mode shape, and damping factor are investigated using fast Fourier transformer (FFT) analyzer. The numerical finite element models (FEM) are generated to model, visualize, simulate, and predict the dynamic nature and fatigue-life characteristics of the optimal S-VAWT composite blade configurations. A correlation between the experimental and numerical results is established. The study findings highlight the significant impact of VAWT composite blades in enhancing the dynamic performance and fatigue-life characteristics of Savonius VAWTs. Furthermore, a small damage percentage of 2.8% predicted by the finite element analysis (FEA) for the optimal S-VAWT composite blade configuration validated the sustainability of the VAWT composite blade configurations in dynamic loading conditions.

Numerical Study of Control Rod's Cross-Section Effects on the Aerodynamic Performance of Savonius Vertical Axis Wind Turbine with Various Installation Positions at Suction Side

Numerical Study of Control Rod's Cross-Section Effects on the Aerodynamic Performance of Savonius Vertical Axis Wind Turbine with Various Installation Positions at Suction Side

Experimental and simulation investigation of a Savonius vertical axis wind turbine for residential applications: a case study in Indonesia

The aim of this study was to investigate several geometric designs to improve the performance of a Savonius vertical axis wind turbine (SVAWT) at low wind speeds. The SVAWT models were numerically tested using ANSYS prediction software to determine the best performance. Furthermore, a SVAWT prototype was experimentally evaluated in subsonic wind tunnels at wind speeds of 1–5 m/s to determine the electrical power produced. The experimental results were used as input parameters for HOMER tools to optimise renewable energy systems and establish the prototype’s techno-economic environmental viability for satisfying the residential demand load. The simulation results showed that the maximum power coefficient obtained was 0.25 for a SVAWT model with a twist angle of 45° at a wind speed of 5 m/s. The experimental results showed that the modified SVAWT produced 494.9 W of electrical power at a wind speed of 5 m/s. The results confirmed that the cost of electrical energy following an initial investment in the optimised renewable energy system configuration (a grid-connected 1-kW SVAWT with a – kW electrical converter and two battery strings) was 0.0963/kWh and 4,425. This setup achieves a 65.8% renewable fraction, cutting CO2 emissions by over 53.71%, fit for residential use.

A Numerical Analysis on the Performance and Optimization of the Savonius Wind Turbine for Agricultural Use

Given the state of the world nowadays, renewable energy is becoming more and more essential rendering wind turbine electricity quite important. Its shape and the fact that the Savonius vertical axis wind turbine runs at relatively low wind speeds with high torque values makes it suitable for practical uses such as that of an irrigation system in agriculture industry. This paper utilizes numerical research with Computational Fluid Dynamics (CFD) to investigate the performance of a vertical-axis wind turbine. The ANSYS CFD program was engaged to construct the simulations during the pre- and post-processing stages. Wind speed remained constant while the angular velocity was altered to enable analysis of the flow through the wind turbine. Because of its mechanical simplicity, the primary profile of a semicircle has remained a typical option for turbines that generate high torque based on drag force. The effects of using elliptical curves and the fluctuation in thickness along the profile chord were both examined in this study. Equivalently, an attempt to optimize the rotor's design was made. After the performance of a numerical simulation, a geometry consisting of simple circle arcs was developed, with a 10.9% improvement in the power coefficient, analogous to prior optimizations with more complicated geometries. The numerical results derived include the torque coefficient evolution throughout a full rotation as well as the distribution of vorticity magnitude at different rotor points.

PENGARUH KONTROLER MAXIMUM POWER POINT TRACKING (MPPT) TERHADAP EFISIENSI DAYA VERTICAL AXIS WIND TURBINE (VAWT) TIPE SAVONIUS DUA SUDU

The purpose of this research is to determine the effect of Maximum Power Point Tracking (MPPT) controller on the power efficiency of a two-bladed Savonius vertical axis wind turbine (VAWT) with a dimensional diameter of 0.9 m and a height of 1 meter, using 1 mm thick stainless steel plate blades. The MPPT controller is applied to the two-bladed Savonius wind turbine to maintain its operation at the maximum power point. The Perturb & Observe type MPPT controller is used in the study to compare the power output of the Savonius wind turbine when the MPPT system is inactive and when it is active, with three variations of load using resistors of 470 ohm, 560 ohm, and 1000 ohm. The research is conducted by subjecting the turbine blades to three variations of wind thrust at speeds of 4.9 m/s, 5.8 m/s, and 6.4 m/s. The testing without using MPPT resulted in an average power of 0.199 Watt, while using MPPT resulted in an average power of 0.620 Watt. The research findings indicate an average power difference of 0.421 Watt, representing an increase of 317.713%. The average power efficiency of the turbine increased by 2.331% compared to the calculated maximum power of the two-bladed Savonius wind turbine. The average power coefficient (Cp) of the two-bladed Savonius wind turbine without MPPT and with MPPT is 0.159% and 0.509%, respectively, indicating a positive effect of MPPT as it led to an average increase in power coefficient of 0.350%.

STUDI NUMERIK TURBIN ANGIN SAVONIUS: TORSI MEKANIK, DIAMETER POROS, DAN DAYA

One of the renewable energy sources that can be used to generate electricity is wind energy. This research aims to numerically study the Savonius Vertical Axis Wind Turbine (VAWT) type to obtain the mechanical torque, load torque, shaft diameter, and the empirical equation showing the relationship between the mechanical torque and power generated. The numerical study employs MATLAB R2018a software with the parameters mechanical torque, load torque, and power. The obtained mechanical torque is also used to determine the design of the shaft diameter based on its maximum mechanical torque. From this numerical study, the value of mechanical torque is greater than the mechanical load, and it also obtains the empirical equation of the relationship between mechanical torque and power. Validation is carried out on the empirical equation with valid results as it has the ± 10% tolerance. Furthermore, it is obtained that the design of the minimum shaft diameter of the wind turbine with PLA (Polylactic Acid) filament material is 2 mm. This Savonius turbine design can be used for placement on vehicles and in areas in Indonesia with low to high wind speeds with variations between 1 m/s – 17 m/s.

Computational fluid dynamics investigations over conventional and modified Savonius wind turbines

Wind turbines are devices that convert the kinetic energy present in the wind into clean, sustainable, and effectively renewable energy that could be used to generate electricity. A Savonius wind turbine is a drag-based vertical axis wind turbine (VAWT) that is known to have low noise levels and good starting characteristics even at low wind speeds. Its disadvantage lies in its low efficiency or low coefficient of performance. Exploring ways to increase the coefficient of performance, numerical investigations were carried out on different modified Savonius VAWT configurations, having different curvatures, different overlap percentages, added mini blades, and fitted out with extended surfaces. These investigations were computationally executed on Ansys Fluent™ using the sliding mesh technique. Two-dimensional simulations, on a Bach blade curvature with zero overlap as well as a half-circle and a polynomial curvature with overlap, showed that for a wind speed of 5 m/s and a tip speed ratio of 0.8, the half-circle blade curvature having an overlap of 20% performs best, yielding the highest net (average) coefficient of moment, equal to 0.3065. Results also show that the addition of mini blades to this optimal configuration produces a slight improvement in the coefficient of moment. However, the addition of extended surfaces onto the blades caused the minimum coefficient of moment to be a substantial negative value and thus resulting in a much lower value for the turbine's average coefficient of moment.

Enhancing Savonius Vertical Axis Wind Turbine Performance: A Comprehensive Approach with Numerical Analysis and Experimental Investigations

Small-scale vertical-axis wind power generation technologies such as Savonius wind turbines are gaining popularity in suburban and urban settings. Although vertical-axis wind turbines (VAWTs) may not be as efficient as their horizontal-axis counterparts, they often present better opportunities for integration within building structures. The main issue stems from the suboptimal aerodynamic design of Savonius turbine blades, resulting in lower efficiency and power output. To address this, modern turbine designs focus on optimizing various geometric aspects of the turbine to improve aerodynamic performance, efficiency, and overall effectiveness. This study developed a unique optimization method, incorporating a new blade geometry with guide gap flow for Savonius wind turbine blade design. The aerodynamic characteristics of the Savonius wind turbine blade were extensively analyzed using 3D ANSYS CFX software. The optimization process emphasized the power coefficient as the objective function while considering blade profiles, overlap ratio, and blade number as crucial design parameters. This objective was accomplished using the design of experiments (DOE) method with the Minitab statistical software. The research findings revealed that the novel turbine design “OR0.109BS2BN2” outperformed the reference turbine with a 22.8% higher power coefficient. Furthermore, the results indicated a trade-off between the flow (swirling flow) through the gap guide flow and the impact blockage ratio, which resulted from the reduced channel width caused by the extended blade tip length.

Numerical Analysis of Double Stack Blade Savonius Wind Turbine with Secondary Blades

In this work, the performance of the Savonius vertical axis wind turbine with secondary blades was investigated numerically. The impacts of two geometric parameters of the secondary blades, including the height of secondary blades (h) and the distance between the main and the secondary blades (b) on the output torque were analyzed. Numerical simulations were performed by a commercial CFD code, ANSYS FLUENT 18.2. Numerical results show that employing secondary blades has a constructive impact on the output torque compared to the case without secondary blades. Moreover, the studied geometric parameters of the secondary blades have a significant impoact on the performance of the proposed turbine. It can be seen that by increasing the height of secondary blades, the angular position of the maximum torque is shifted. At b = 2.5 mm, the difference between the models is more comparable. Models h = 6 and 12 mm have the highest output torque, although with a slight difference between them. Model h = 12 mm has the highest output torque. At b = 7.5 mm, the difference between the models is more comparable than b = 2.5 mm. Model h = 12 mm has the highest output torque and models h = 3 and 6 mm are in the next levels. Obtained results in the second section demonstrate that by growing the distance between the secondary and the main blades, in the case of h = 3 mm, the produced torque declines. Furthermore, by increasing the distance between the secondary and the main blades from b = 0 mm to b = 2.5 mm and b = 7.5 mm, the amount of torque produced decreases by 17.33 and 26.66%, respectively. Moreover, by augmenting the distance between the secondary and main blades from b = 2.5 mm to b = 7.5 mm (200% growth), the produced torque decreases by 11.3%.

Design and Fabrication of Solar Windmill

In recent era, research and development activities in the field of renewable energy, especially wind and solar, have been considerably increased, due to the worldwide energy crisis and high global emission. Wind turbines & Solar are becoming popular in the renewable energy world. The design of hybrid electricity generation system by utilizing both solar and wind renewable energy to the domestic household in the remote area and for many applications like beside railway tracks, railway stations, highways for power generation, and for charging of electrical vehicle. The primary goal of the project is to design and create a compact wind turbine and solar panel to be used as an efficient way to generate electricity anywhere. It is not possible to operate a horizontal axis wind turbine for domestic use. Because it can function in low wind conditions as well, the Savonius vertical axis wind turbine may be a preferable option. According to tests, hybrid systems are the best option for supplying "high quality" power.

CFD Investigation and Optimization on the Aerodynamic Performance of a Savonius Vertical Axis Wind Turbine and Its Installation in a Hybrid Power Supply System: A Case Study in Iran

In this study, a 3D-CFD simulation on the effect of various design and operating parameters, namely the number of blades, overlap ratio, spacing size, arc angle, shape factor, presence of curtain, wind velocity, and multi-bucket rotor, on the aerodynamic performance of a Savonius vertical axis wind turbine (VAWT) is conducted. In order to evaluate the effect of each parameter, the rotor’s power coefficient (Cp) for different tip speed ratio (TSR) values and overall torque as a function of the azimuth angle are investigated. The results show that the generated power of a solid rotor with more buckets is less than that of the two-bladed rotor, and by decreasing the overlap ratio and spacing size, Cp values are enhanced. Moreover, a rotor with a larger bucket arc angle has less Cp value and total torque, in addition to shape factor, which changes the configuration of the rotor by adding arms, thus enhancing the aerodynamic performance of the prototype. Furthermore, it is shown that installing a curtain in the upstream section of the rotor improves Cp value by directing airflow. Moreover, it is observed that by increasing inlet wind velocity and, subsequently, the Reynolds number, generated power is boosted. In addition, it is noted that a suitable multi-bucket rotor configuration can boost generated power. Finally, the optimum design is achieved by using the Kriging method. Based on the optimization results, a 2-bladed Savonius VAWT with an overlap ratio of 0, spacing size of 0 (m), arc angle of 170°, shape factor of 0.5, and inlet wind velocity of 12 (m/s) at TSR = 0.37 introduces the highest efficiency.

Recent Advancement in Savonius Wind Turbine- A Review

In the steps to save our earth from global warming every nation focused on their own way to promote green energy among which the Savonius vertical axis wind turbine is one of the excellent viable solutions for scavenging wind energy in a downtown background, due to distinctive characteristics such as compactness, self-starting ability at light wind, minimum noise level, with relatively reasonable price and simple assembly. However, the traditional Savonius Wind Turbines with semicircular blades has a proportionately low power coefficient together with a high negative torque produced by the returning blade is a crucial disadvantage of this rotor. This work focuses on reviewing and giving an overview on the form of the wings of Savonius Vertical Axis Wind Turbine. This paper also aims to give a run through of the several augmentation approaches used in Savonius rotor over the last four decades. In this paper, a brief on all possible segments and parts of the machine is given after a brief analysis and research on each topic.

Design and Analysis of a Novel Adjustable SVAWT for Wind Energy Harvesting in New Energy Vehicle

The new energy vehicle is a robust measure to solve the problem of global warming. However, the new energy vehicle generally has the disadvantages of short mileage and difficulty in finding public chargers. The combination of wind energy harvest and new energy vehicle can be conducive to the promotion of the new energy vehicle. This paper proposes a novel adjustable Savonius vertical axis wind turbine (SVAWT). It contains three parts: an energy absorption module, an energy recovery module, and an energy conversion module. The energy absorption module includes four blades with staggered distribution in two layers. The overlap ratio of the blades can be adjusted by the wind speed, which can ensure the SVAWT has a higher energy transfer efficiency. The energy recovery module adjusts the overlap ratio of the blades without interruption by utilizing the self-rotation and the orbital revolution of the gears. The energy conversion module converts mechanical energy into electric energy and supplies power for the vehicle after adjustment by the voltage regulator module. Based on actual operating data, it can be found that the variation trend of power of the blades absorbing is consistent with wind speed and increases with the wind speed. Under four actual operating conditions, the root mean square value of the blades absorbing power are 7.0 W, 7.1 W, 3.9 W, and 5.1 W, respectively. These results reveal that the proposed novel adjustable SVAWT has high recovery power potential and can provide a valuable solution to the practical applications of wind energy harvesting.

Power Performance Analysis Based on Savonius Wind Turbine Blade Design and Layout Optimization through Rotor Wake Flow Analysis

Savonius vertical axis wind turbines have simple structures, can self-start in environments with low wind speed and strong turbulence intensity, and can be installed at low costs. Therefore, installation is possible in urban centers with low wind speeds, which may contribute to the construction of a decentralized power system. Savonius wind turbines are operated by drag force, with the blades moving in the same direction as the flow current providing the thrust force and those moving in the opposite direction of the wind being rotated by the drag force. In this study, the Savonius wind turbine design was examined to develop a stable wind turbine for use in urban centers at low wind speeds. The Savonius rotor design variables (aspect and overlap ratios) and blade forms (semi-circular, Bach, and elliptical type) were examined using computational fluid dynamics analysis. Moreover, a rotor capable of providing the target output was designed and maximum rotor efficiency of 18% was realized. Further, changes to the flow corresponding with various turbine layouts were analyzed to determine the arrangement that would maximize turbine performance. The results showed that the maximum efficiency of the turbines was in the 17–19% range and without significant variation.

Influence of position and wind direction on the performance of a roof mounted vertical axis wind turbine

The ideal position for a roof mounted wind turbine is investigated experimentally in a wind tunnel. The set-up consists of two cube-shaped buildings. A Savonius (drag driven) vertical axis wind turbine is placed on one of the buildings and its position is varied. Three different locations on the cube and two different turbine heights are examined. Wind from five directions is simulated to obtain a holistic characterization of the problem. The performance of the turbine is evaluated directly through measurements of the converted power. This is complemented by measurements of the surface pressure on the cubes to gain insight into the flow field. A central position on the building was found to maximize the power output for a uniform wind rose, independent of the turbine height. Placing the turbine higher above the roof increased performance for wind normal to the faces of the buildings, while a lower position showed slight advantages for the other wind directions. Overall improved performance for the roof mounted wind turbine was observed compared to the same turbine without a cube present.

Numerical Investigation on the Effect of Profile and Blade Numbers in a Savonius Vertical Axis Wind Turbine

Small-scale wind turbines are considered recently as an attractive source of renewable energy, especially at remote area with respect to city centre. The design and characterization of a small vertical wind turbine are introduced through this work. A CFD analysis has been used as a first step in design to simulate the flow around the vertical blades of the small wind turbine. Different parameters have been taken into account in this work such as blades number, shape, and existence of stator blades deflector. Three different versions depend on blade profile have been examined. The turbulence model with sliding mesh in CFD have been performed. In this paper, a performance of small-scale of vertical wind turbine represented by CFD results of power coefficient, and optimal freestream velocity of this model are presented. The results showed that using 8 blades of VAWT instead of 4 blades with the same profile of blade has enhanced VAWT performance up to 64%. Also, increasing the concave profile of the blade can rise the torque produced by approximately 8%, however more increase in concave shape cause drop down by 5.6 %. Moreover, including stator deflector to the VAWT design has ability to increase the torque produced by 70 %. The output of these results will help to choose the optimum configuration of the small vertical wind turbine to implement this design experimentally as a next step.

Investigation into the Aerodynamic Performance of a Vertical Axis Wind Turbine with Endplate Design

For the past decade, research on vertical axis wind turbines (VAWTs) has garnered immense interest due to their omnidirectional characteristic, especially the lift-type VAWT. The H-rotor Darrieus VAWT operates based on the lift generated by aerofoil blades and typically possesses higher efficiency than the drag-type Savonius VAWT. However, the open-ended blades generate tip loss effects that reduce the power output. Wingtip devices such as winglets and endplates are commonly used in aerofoil design to increase performance by reducing tip losses. In this study, a CFD simulation is conducted using the sliding mesh method and the k-ω SST turbulence model on a two-bladed NACA0018 VAWT. The aerodynamic performance of a VAWT with offset, symmetric V, asymmetric and triangular endplates are presented and compared against the baseline turbine. The simulation was first validated with the wind tunnel experimental data published in the literature. The simulation showed that the endplates reduced the swirling vortex and improved the pressure distribution along the blade span, especially at the blade tip. The relationship between TSR regimes and the tip loss effect is also reported in the paper. Increasing VAWT performance by using endplates to minimise tip loss is a simple yet effective solution. However, the improvement of the power coefficient is not remarkable as the power degradation only involves a small section of the blades.

Effect of the Phase-Shift Angle on the vertical axis Savonius wind turbine performance as a renewable-energy harvesting instrument

Wind energy is the third-largest renewable energy source after hydro and solar energy, so it has great potential in increasing renewable energy as a percentage of national energy. However, wind energy installation is only at 0.25% of the existing potential; so, it still needs to be developed. One of the development efforts is to optimize the wind turbine rotor design. Savonius rotors are among the most popular rotors to convert wind energy into electrical energy. The Savonius turbine is a simple structure, easy to modify to upgrade Savonius performance, and can be operated at low velocity. Phase-shift angles of 0°, 30°, 60°, and 90° were utilized in this study on a two-stage Savonius wind turbine. This study was carried out using Solver CFX utilizing the Computational Fluid Dynamic technique on the ANSYS Student version software. An SST (shear stress transport) turbulence model with steady-state turbulence was used. The purpose of this study was to assess the influence of PSA on the performance of the Savonius two-stage turbine. Factorial design analysis was used in conjunction with the CFD approach. The results indicated that PSA influenced the Savonius turbine’s performance, with 30° being the optimal PSA. Simultaneously, the Cpmax may be obtained using 0.29. The factorial design study with two components revealed that the Phase-Shift Angle had a considerable effect on rotor performance, and the two factors (TSR and PSA) had an interaction.