Contact Force Values Research Articles

Numerical analysis of running resistance of a completion string with packers and sliding sleeves in horizontal wells

The installation of a completion string in small-diameter horizontal wells often presents challenges such as instability, bending, and high frictional resistance. To accurately estimate the running resistance during deployment and ensure safe descent to the bottom of the well, a three-dimensional numerical model has been developed incorporates real-time contact interaction between the completion string and the wellbore, while maintaining precision and field applicability. The analysis evaluates several factors, including buckling behavior, average and dynamics transient value of contact force, axial forces, and frictional forces. Results reveal that the upper pipe string exerting thrust on the lower pipe string causes bending and spiral buckling along with resulting contact with wellbore. Maximum hook load and maximum negative axial force occur at a inclination angle of 65°. Contact strength is more pronounced in inclined and horizontal section compared to vertical section. Leveraging extensive data, the study has yielded a quick prediction formula for quickly calculating the resistance experienced by a completion string of field area. The numerical results offer valuable insights into comprehending the resistance encountered during the descent of a completion string in horizontal wells, and provide robust theoretical support for predicting descent resistance.

Quantitative investigation of acute lesions created by ethanol infusion into the vein of Marshall

BackgroundEthanol infusion into the vein of Marshall (EIVOM) has been performed as an adjunctive atrial fibrillation therapy. However, the time course change, quantitative lesion investigation, and effects on epicardial fat pads and fractionated atrial electrograms created by EIVOM have never been investigated. ObjectiveThis study aimed to perform a quantitative analysis of lesions created by EIVOM. MethodsWe created voltage maps using a 3-dimensional mapping system immediately before and 30 minutes and 60 minutes after performing EIVOM to study the time course change in the lesions. We compared differences in the average contact force value required for successful conduction block in the Marshall vein area of patients with and without EIVOM. We also investigated effects of EIVOM on the area of complex fractionated atrial electrograms before and after EIVOM. We measured the total epicardial fat pad volume before and after EIVOM by computed tomography. ResultsVoltage was significantly reduced after EIVOM, and there were significant differences in voltage reduction between the control status and 30 minutes and 60 minutes after EIVOM (P < .05). The average contact force value was significantly lower with vs without EIVOM (P < .05). The total epicardial fat volume and complex fractionated atrial electrogram area also significantly decreased after EIVOM (P < .05). ConclusionEIVOM provided significant therapeutic effects on the left atrial tissue perpetuating atrial fibrillation, which was demonstrated by a quantitative analysis.

The Impact of Contact Force on Signal Quality Indices in Photoplethysmography Measurements

Photoplethysmography (PPG) is widely used to assess cardiovascular health. Yet, its effectiveness is often hindered by external factors like contact force (CF), which significantly affects the accuracy and reliability of measurements. This study investigates how variations in the CF at the index fingertips influence six signal quality indices (SQIs)—including the perfusion index, skewness, kurtosis, entropy, zero-crossing rate, and relative power—using data from 11 healthy participants. Our analysis of normalized CF values reveals that lower CF ranges (0.2 to 0.4) may be optimal for extracting information about perfusion and blood flow. However, they may not be the best range to capture all the physiological details within the PPG pulse. In contrast, higher CF ranges (0.4 to 0.6) enable capturing more complex signals that could be physiologically representative. The findings underscore the necessity of considering viscoelastic tissue properties and individual biomechanical differences, advocating for both the normalization of CF for improved cross-subject comparison and personalized CF calibration to adapt PPG devices to diverse populations. These strategies ensure measurement reliability and consistency, thereby advancing the accuracy of cardiac and vascular assessments. Our study offers guidelines for adjusting the CF levels to balance signal detail and perfusion quality, customized to meet specific analytical requirements, with direct implications for both clinical and research environments.

Analysis of impact response and damage evolution in multi‐scale of novel 3D carbon fiber‐reinforced polyetheretherketone composites

AbstractThermoplastic composites have a high application demand in aerospace, marine military and other cutting‐edge industry. However, it poses a considerable obstacle in achieving three‐dimensional (3D) thermoplastic composites because of the inadequate infiltration of highly viscous thermoplastic resins. In this paper, high‐toughness Polyetheretherketone (PEEK) resin‐based 3D orthogonal carbon fiber thermoplastic composites were designed and obtained. Low‐velocity impact test was conducted on 3D orthogonal woven composite (3DOWC) under the energy levels of 5 and 10 J, and its performance was compared with that of the 2D unidirectional layup composite (2DULC) and the 2D plain layup composite (2DPLC). The results showed that 3DOWC possessed superior elastic energy absorption capacity and less damage morphology compared to 2D composites. 3DOWC had the highest contact force value of 2420.25 N at 10 J, which is 36.83% higher than that of 2DPLC. Furthermore, a finite element model in multi‐scale was established to investigate the damage evolution and failure mechanism of the 3D orthogonal woven CF/PEEK composites. The damage morphology observed in both experimental and numerical findings demonstrated that the matrix shedding, while the yarn fractured on the nonimpact side beneath the impact point. Additionally, enhancing the tensile strength of the yarn in the bottom layer can lead to further improvement in impact resistance. This work provides an innovative method for manufacturing 3D thermoplastic composites and lays the foundation for the impact simulation analysis of such composites.Highlights A novel approach was introduced for fabricating 3D carbon fiber/PEEK composites, which exhibits remarkable resistance to impact. A comprehensive investigation was conducted to evaluate the impact properties of 3D thermoplastic composite compared to 2D composite. A finite element model in multi‐scale including failure criteria was established to simulate the damage evolution.

Ablation catheter–induced mechanical deformation in myocardium: computer modeling and ex vivo experiments

Cardiac catheter ablation requires an adequate contact between myocardium and catheter tip. Our aim was to quantify the relationship between the contact force (CF) and the resulting mechanical deformation induced by the catheter tip using an ex vivo model and computational modeling. The catheter tip was inserted perpendicularly into porcine heart samples. CF values ranged from 10 to 80 g. The computer model was built to simulate the same experimental conditions, and it considered a 3-parameter Mooney-Rivlin model based on hyper-elastic material. We found a strong correlation between the CF and insertion depth (ID) (R2 = 0.96, P < 0.001), from 0.7 ± 0.3 mm at 10 g to 6.9 ± 0.1 mm at 80 g. Since the surface deformation was asymmetrical, two transversal diameters (minor and major) were identified. Both diameters were strongly correlated with CF (R2 ≥ 0.95), from 4.0 ± 0.4 mm at 20 g to 10.3 ± 0.0 mm at 80 g (minor), and from 6.4 ± 0.7 mm at 20 g to 16.7 ± 0.1 mm at 80 g (major). An optimal fit between computer and experimental results was achieved, with a prediction error of 0.74 and 0.86 mm for insertion depth and mean surface diameter, respectively.Graphical

Investigating the influence of low temperatures on the pantograph serviceabil-ity in an electric rolling stock equipped with panhead suspension with controlled intraspring pneumatic elements

The article evaluates the influence of low temperatures on the operation of intra-spring pneumatic element installed in panhead suspension of electric rolling stock. Experimental planning methods are used during experimental studies of a pantograph equipped with intra-spring pneumatic elements in panhead suspension. The laboratory facilities of the 'Railway Power Supply' department of the Omsk state transport university are being utilized for the experiments. The data obtained as a result of experimental studies indicate a slight increase in the dry friction forces in the intra-spring pneumatic element with a decrease in ambient temperature. In this case, the static characteristic of the panhead sus-pension changes slightly due to the fact that the main element forming it is a cylindrical spring. The results of dynamic tests show that over time the shell heats up, which leads to a decrease in its final influence on the dynamics of interaction between the pantograph and the catenary. Low temperatures (up to –40 °C) have a negative impact on the opera-tion of the pantograph equipped with intra-spring pneumatic elements in the panhead suspension, increasing the dry friction forces in the carriage. The range of changes in contact force values increases by 10-15 %, however. Such an increase in the range of changes in contact force values does not have any significant effect on the quality of current collection. The current collector remains fully operational at temperatures down to –40 °C.

Development and Validation of a Screw Interlock Recognition Method based on Logistic Regression

Conventional robotic screw methods rely on position control and the use of a threshold value, normally a contact force value, to detect the contact between tool and screw, so the nut-runner can be placed correctly on the workpiece. In the case of a dynamic workspace, the variance of the workpiece position will likely cause the nut-runner to be positioned incorrectly and will significantly decrease the success rate of the screw task.This paper proposes a novel method based on a logistic regression model for flexible Human-Robot-Collaboration (HRC) screw assembly operations in highly dynamic workspaces. The proposed method is part of a screwing strategy based on impedance control and developed for HRC applications. The screwing strategy consists of a spiral movement executed by the robot while approaching the workpiece and it is used as a search procedure to find the screw. The proposed method is used to detect when the tool correctly interlocks with the screw head so the robot can proceed with the screwing process. The goal is to stop the spiral movement timely when the nut-runner has correctly interlocked with the screw head to ensure a successful screw task and avoid potential damage to the nut-runner or the workpiece.The proposed screw interlock recognition method utilizes a logistic regression model to observe the contact forces between tool and screw head. The learning model is trained using force data collected from experiments and then its feasibility is validated with further testing.

Modeling and analysis of transition-point disappearance in high-speed railway pantograph-catenary system

During the operation of high-speed railway, the transition-point disappearance phenomenon, which is caused by the deformation of pantograph head, poses a safety threat to the pantograph-catenary system. In this study, the analytical model for transition-point disappearance analysis is presented. The instantaneous profile, as well as the deformation process of the pantograph head under different contact force values and positions or different pantograph-head parameters can be solved using the model. Curve equation, force analysis, coordinate axis rotation, and few other methods are adopted to achieve simplified modeling. The proposed modeling method and analysis conclusion provide theoretical support for the permissible contact force range calculation and pantograph-head parameters optimization to prevent transition-point disappearance. The effectiveness of the proposed model is verified using both finite element simulation and experimental measurements. Finally, a case analysis for the prevention of transition-point disappearance is conducted, using pantographs with the models CX-GI and DSA250 as examples.

Analysis of Surface Topography Changes during Friction Testing in Cold Metal Forming of DC03 Steel Samples

Predicting changes in the surface roughness caused by friction allows the quality of the product and the suitability of the surface for final treatments of varnishing or painting to be assessed. The results of changes in the surface roughness of DC03 steel sheets after friction testing are presented in this paper. Strip drawing tests with a flat die and forced oil pressure lubrication were carried out. The experiments were conducted under various contact pressures and lubricant pressures, and lubrication was carried out using various oils intended for deep-drawing operations. Multilayer perceptrons (MLPs) were used to find relationships between friction process parameters and other parameters (Sa, Ssk and Sku). The following statistical measures of contact force were used as inputs in MLPs: the average value of contact force, standard deviation, kurtosis and skewness. Many analyses were carried out in order to find the best network. It was found that the lubricant pressure and lubricant viscosity most significantly affected the value of the roughness parameter, Sa, of the sheet metal after the friction process. Increasing the lubricant pressure reduced the average roughness parameter (Sa). In contrast, skewness (Ssk) increased with increasing lubrication pressure. The kurtosis (Sku) of the sheet surface after the friction process was the most affected by the value of contact force and lubricant pressure.

Dynamic Buckling Characteristics of Drill String in Horizontal Wells

Buckling may cause drill string damage or even drilling failure. For the 3[Formula: see text]000-m-long horizontal section drill string, a simplified analysis model of drill string in horizontal well is established, and the dynamic response results of axial displacement, angular displacement and contact force are obtained. When buckling, the closer the position of drill string is to the bottom, the later the buckling time, the smaller the buckling deformation degree, the slower the growth rate of axial displacement, and the smaller the attenuation degree of angular displacement and contact force amplitude. After buckling, drill string undergoes tensile deformation and eventually remains stable in the tensile state. After stabilization, from the top of drill string to the bottom of drill string, axial displacement increment increases first, then remains unchanged and then decreases, and the relative torsion angle between different positions gradually decreases. The drill string is always in horizontal contact with the wellbore, resulting in the same contact force values at different locations. The change of well inclination angle does not affect the change law of displacement and contact force. The absolute value of angular displacement is negatively correlated with the change of well inclination angle, and the value of axial displacement increment and contact force is positively correlated with the change of well deviation angle, but the value of contact force is quite close. The research results can provide reference for alleviating the buckling of drill string in horizontal wells.

Identification of Selected Failures in a Pipe Conveyor’s Operation with the Use of the Discrimination Method Based on Continuous Measurement

This paper deals with research on the operational process monitoring of a pipe conveyor for the needs of online diagnostics. The aim of this research is to verify the possibility of identifying the selected pipe conveyor’s failures in its straight section during operation (a missing roller in the idler housing, absent material on the conveyor belt) with the use of a discrimination method. This is an attempt to implement digital transformation with the aim of verifying its possibilities and limitations. The basis for discrimination is a continuous measurement and evaluation of measured values of contact forces in certain rollers’ positions in the hexagonal idler housing. Within this research, eight different measurement regimes were implemented. The use of the method was verified with simulated data using the trace table. We aimed to create prerequisites for online monitoring, which, based on digital transformation, will be deployed to control a transport system. The measurement was realized with the maximum tension force of 28,000 N. From the measurements, a decision-making algorithm was proposed to identify selected failures in the pipe conveyor operation with the use of the discrimination method. Within the algorithm, classifying criteria were determined, in the range of 57 N ÷ 251 N. The results confirm the method’s suitability for its practical assurance of pipe conveyors’ failure-free operation, as the failures were always identified sufficiently in advance, thanks to which, in practice, there was no further damage to the diagnosed devices.

Baseline local impedance and changes in local impedance are predictors of electrode tissue coupling in RF-ablation

Abstract Funding Acknowledgements Type of funding sources: None. Background Radiofrequency (RF) current remains the most ablation technology in the electrophysiologic laboratory. Durable lesion formation without collateral tissue damage is key for obtaining efficient and safe procedures. RF power, duration and contact force are considered as main determinants of lesion size. Recently published data show that electrode tissue coupling (ETC) is another important parameter of lesion formation. This ex vivo model was created to investigate local impedance changes and lesion size when alternating ETC-levels. Methods RF-lesions were created using a force and local impedance sensing catheter in an ex vivo porcine cardiac model. The experimental setup consisted of a saline-filled container, a dispersive electrode, a heated thermostat and a circulation pump to imitate in vivo conditions. Global impedance was kept at 120 Ohm as well as the temperature at 37°C. RF-lesions were created using identic values of RF duration and contact force. A RF power of 20W, 30W, 40W, and 50W was used. The ETC levels were systematically varied between minor and full coupling. In minor ETC-level, only the distal end of the catheter is in contact with the tissue. In full ETC-level, the whole catheter tip is in contact with the tissue. All parameters (power, temperature, global and local impedance, contact force, ETC, lesion size) were measured constantly during application of RF-current, enabling real-time correlation of RF parameters and lesion size. In case of an audible steam pop, RF application was stopped. Results 8654 measurements of lesion depth and diameter were analyzed after creating 72 lesions. Lesion depth and diameter in full ETC-level were significantly higher compared to minor ETC-level (s. Table 1). Interestingly, lesions in lower power levels (20-30 Watt), but full ETC-level became wider and deeper than lesions in high power levels (40-50 Watts), but minor ETC-level (s. Figure 1). These observations were made despite shorter RF-duration (54.00 ± 13.07 s vs. 47.11 ± 17.57 s, p=0.032) in lesions with full ETC-level due to higher incidence of steam pops (14 vs. 6 steam pops, p = 0.032). Baseline LI and LI-drop were significantly higher in full ETC-level (Figure 2), but no relevant difference was observed in baseline GI. Conclusion Baseline LI and LI changes during ablation provide information about ETC-levels and interaction of the RF ablation catheter with cardiac tissue. ETC-levels, as predicted by LI, had a significantly higher impact on RF lesion size than RF power or RF-duration. Therefore, LI should be monitored during RF ablation for estimating ETC-levels and lesion formation.

Local impedance changes are a suitable real time surrogate for lesion formation in RF-ablation

Abstract Funding Acknowledgements Type of funding sources: None. Background Radiofrequency current remains one of the most important techniques for catheter ablation. Creating durable lesions is key for sufficient and safe procedures. Several possibilities were tested for estimating the progress of lesion formation. For instance, force-time-integral, ablation index and lesion size index are used to assess quality of RF-application and, therefore, lesion size and durability. Nevertheless, recovered conduction after acute conduction block remains an issue in RF-ablation. The aim of this study was to evaluate local impedance (LI) changes as real time surrogate for lesion formation. Methods RF-lesions were created using an ex vivo porcine cardiac model and a force and local impedance sensing catheter. The experimental setup consisted of a saline-filled container, a dispersive electrode, a heated thermostat and a circulation pump to imitate in vivo conditions. Global impedance was kept at 120 Ohm as well as the temperature at 37°C. RF-lesions were created using identic values of RF duration and contact force. RF power (20W, 30W, 40W, 50W) and level of electrode-tissue-coupling were also systematically varied between minor and full coupling. In minor ETC-level, only the distal end of the catheter is in contact with the tissue. In full ETC-level, the whole catheter tip is in contact with the tissue. All parameters (power, temperature, global and local impedance, contact force, ETC, lesion size) were measured constantly during application of RF-current, enabling real-time correlation of RF parameters and lesion size. In case of an audible steam pop, RF application was stopped. Results Including a total of 8654 measurements into the analysis, maximum diameter and depth were 9.51 ± 1.91 mm and 7.29 ± 2.50 mm in average. Local impedance correlated well with lesion depth (r= 0,78, p&amp;lt;0,001), as well as lesion diameter (r=0,652, p&amp;lt;0,001, Figure 1). After significant declines of LI at the beginning of RF-application, it slowly approximates a minimum. Lesion size on the other hand, rises exponentially in first seconds and gets closer to a maximum after more than 25 seconds. This relationship is illustrated in Figure 2. With decreasing lesion growth at the end of RF-application, LI changes decrease to low level (Figure 3). Conclusion Lesion formation in RF-ablation is not linear during application of RF current. Local impedance changes seem to be a suitable real-time surrogate for assessing changes in lesion size during ablation.

Is catheter-tissue contact force value important for ablation of ventricular arrhythmias originating from the left ventricular papillary muscles?

Good catheter-tissue contact is mandatory to create effective ablation lesions. The minimal contact force value for ablation of arrhythmias originating from the left ventricle is 8.0-10.0 grams but is not known for arrhythmias arising from papillary muscles. To analyze contact force values during successful ablation procedures of arrhythmias originating from the left ventricular papillary muscles. 24 consecutive patients (mean age 57.9 ± 11.9 years, 16 males) underwent ablation of premature ventricular complexes originating from left ventricular papillary muscles with the use of CARTO electro-anatomical system and intracardiac echocardiography. Acute complete abolition of ventricular ectopy was obtained in 23 (96%) patients. The fluoroscopy time was 3.9 ± 3.5 min and procedure duration - 114.8 ± 37.9 min. The mean contact force during successful ablations was 3.0 ± 1.1 grams and 3.18 ± 1.8 grams for antero-lateral and postero-medial papillary muscle, respectively (NS). The mean contact force during a single unsuccessful ablation was 3.0 grams. At control Holter ECG, the mean Ectopy Burden was Reduced in the Antero-Lateral Papillary Muscle Group from 18.0% ± 7.9% to 2.6% ± 2.9% (p = 0.005415) and in the Postero-Medial Papillary Muscle Group - from 34.8% ± 13.7%-1.7% ± 1.3% (p = 0.012694). During Median 27 (IQR: 17-34) Months of Follow-up There one Recurrence of Arrhythmia. The values of contact force for successful ablation of ventricular ectopy originating from the left ventricular papillary muscles may be much lower than those for ablation of other foci which questions the role of contact force measurement when ablating these arrhythmias.

Multibody Dynamics Model of the Cycloidal Gearbox, Implemented in Fortran for Analysis of Dynamic Parameters Influenced by the Backlash as a Design Tolerance

Abstract In this study, dynamical parameters of the cycloidal gearbox working at the constant angular velocity of the input shaft were investigated in the multibody dynamics 2D model implemented in the Fortran programming language. Time courses of input and output torques and forces acting on the internal and external sleeves have been shown as a function of the contact modelling parameters and backlash. The analysis results in the model implemented in Fortran were compared with the results in the 3D model designed using MSC Adams software. The values of contact forces are similar in both models. However, in the time courses obtained in MSC Adams there are numerical singularities in the form of peaks reaching 500 N for the forces at external sleeves and 400 N for the forces acting at internal sleeves, whereas in the Fortran model, there are fewer singularities and the maximum values of contact forces at internal and external sleeves do not exceed 200 N. The contact damping and discretisation level (the number of discrete contact points on the cycloidal wheels) significantly affect the accuracy of the results. The accuracy of computations improves when contact damping and discretisation are high. The disadvantage of the high discretization is the extended analysis time. High backlash values lead to a rise in contact forces and a decrease in the force acting time. The model implemented in Fortran gives a fast solution and performs well in the gearbox optimisation process. A reduction of cycloidal wheel discretisation to 600 points, which still allows satisfactory analysis, could reduce the solution time to 4 min, corresponding to an analysis time of 0.6 s with an angular velocity of the input shaft of 52.34 rad/s (500 RPM).

The influence of local wear and contact roughness on mixed lubrication of marine stern bearing with misaligned shaft

AbstractThe marine stern bearing provides supporting force by lubricating film to minimise the contact friction with the propeller shaft. A model considers local wear and asperity contact is proposed to investigate the mixed lubrication of bearing with misalignment. The finite difference method and over‐relaxation iteration method are employed to solve the average Reynolds equation. The lubrication behaviour includes hydrodynamic pressure, film thickness, contact force and friction coefficient were calculated. The influence of sliding speed, local wear, contact roughness, misalignment angle, elastic deformation and eccentricity ratio is discussed in detail. The critical speed from mixed lubrication to fluid lubrication is obtained by employing the Stribeck curve. Moreover, the dimensionless average hydrodynamic pressure, film thickness and the peak value of contact force are compared.

PO-03-064 BASELINE LOCAL IMPEDANCE AND CHANGES IN LOCAL IMPEDANCE ARE PREDICTORS OF ELECTRODE TISSUE COUPLING IN RF-ABLATION

Radiofrequency (RF) current remains the most used ablation technology in the EP lab. Durable lesion formation without collateral tissue damage is key for obtaining efficient and safe procedures. RF power, duration and contact force (CF) are considered as main determinants of lesion size. Recently published data show that electrode tissue coupling (ETC) is another important parameter of lesion formation. This ex vivo model was created to investigate local impedance (LI) changes and lesion size when alternating ETC-levels. RF-lesions were created using a CF and LI sensing catheter in an ex vivo porcine cardiac model. The experimental setup consisted of a saline-filled container, a dispersive electrode, a heated thermostat and a circulation pump to imitate in vivo conditions. Global impedance was kept at 120 Ohm as well as the temperature at 37°C. RF-lesions were created using identic values of RF duration and contact force. RF power of 20W, 30W, 40W, and 50W was used. The ETC levels were systematically varied between minor and full coupling. In minor ETC-level, only the distal end of the catheter is in contact with the tissue. In full ETC-level, the whole catheter tip is in contact with the tissue. All parameters (power, temperature, global and local impedance, CF, ETC, lesion size) were measured constantly during RF-application, enabling real-time correlation of all parameters and lesion size. 8654 measurements of lesion depth and diameter were analyzed after creating 72 lesions. Lesion depth and diameter in full ETC-level were significantly higher compared to minor ETC-level (s. Table 1). Interestingly, lesions in lower power levels (20-30 Watt), but full ETC-level became wider and deeper than lesions in high power levels (40-50 Watts), but minor ETC-level (s. Figure 1). These observations were made despite shorter RF-duration (54.00 ± 13.07 s vs. 47.11 ± 17.57 s, p=0.032) in lesions with full ETC-level due to higher incidence of steam pops (14 vs. 6 steam pops, p = 0.032). Baseline LI and LI-drop were significantly higher in full ETC-level (Figure 1), but no relevant difference was observed in baseline GI. Baseline LI and LI changes during ablation provide information about ETC-levels and interaction of the RF ablation catheter with cardiac tissue. ETC-levels, as predicted by LI, had a significantly higher impact on RF lesion size than RF power or RF-duration. Therefore, LI should be monitored during RF ablation for estimating ETC-levels and lesion formation.Tabled 1Table 1. Lesion size and impedance changes in different ETC-levels.Minor ETC (n=36)Full ETC (n=36)p-valueMaximum diameter [mm]8.48 ± 1.6110.54 ± 1.63<0.001Maximum depth [mm]5.13 ± 0.999.45 ± 1.45<0.001Start LI [Ω]236.89 ± 26.42300.67 ± 21.61<0.001Start GI [Ω]150.61 ± 21.61151.33 ± 23.680.893LI-drop [Ω]-53.61-125.53<0.001GI-drop [Ω]-21.33-33.44<0.001 Open table in a new tab

PO-03-066 LOCAL IMPEDANCE CHANGES ARE A SUITABLE REAL TIME SURROGATE FOR LESION FORMATION IN RF-ABLATION

Radiofrequency current remains one of the most important techniques for catheter ablation. Creating durable lesions is key for sufficient and safe procedures. Several possibilities were tested for estimating the progress of lesion formation. For instance, force-time-integral, ablation index and lesion size index are used to assess quality of RF-application and, therefore, lesion size and durability. Nevertheless, recovered conduction after acute conduction block remains an issue in RF-ablation. The aim of this study was to evaluate local impedance (LI) changes as real time surrogate for lesion formation. RF-lesions were created using an ex vivo porcine cardiac model and a contact force and LI sensing catheter. The experimental setup consisted of a saline-filled container, a dispersive electrode, a heated thermostat and a circulation pump to imitate in vivo conditions. Global impedance was kept at 120 Ohm as well as the temperature at 37°C. RF-lesions were created using identic values of RF duration and contact force. RF power (20W, 30W, 40W, 50W) and level of electrode-tissue-coupling were also systematically varied between minor and full coupling. All parameters (power, temperature, global and local impedance, contact force, ETC, lesion size) were measured constantly during 60 seconds of RF-application, enabling real-time correlation of RF parameters and lesion size. In case of an audible steam pop, RF application was stopped. Including a total of 8654 measurements into the analysis, maximum diameter and depth were 9.51 ± 1.91 mm and 7.29 ± 2.50 mm in average. LI correlated well with lesion depth (r= 0,78, p<0,001), as well as lesion diameter (r=0,652, p<0,001). After significant declines of LI at the beginning of RF-application, it slowly approximates a minimum. Lesion size on the other hand, rises exponentially in first seconds and gets closer to a maximum after more than 25 seconds. With decreasing lesion growth at the end of RF-application, LI changes decrease to low level (Figure 1). Lesion formation in RF-ablation is not linear during application of RF current. Local impedance changes seem to be a suitable real-time surrogate for assessing changes in lesion size during ablation.

Enhanced impact resistance of three‐dimensional woven composites with double‐layer core structure

AbstractIn this study, to further improve the anti‐impact property of 3D woven spacer composites (3DWSC), three kinds of integrated 3DWSC with double‐layer cores assembled at different height combinations of 4 + 8 mm, 6 + 6 mm, and 8 + 4 mm, were designed and prepared. And the impact performances and the post‐impact lateral compressive properties of the resulting composites were investigated and compared to the single‐layer 3DWSC of the same height. The results show that among the three combinations, 3DWSC‐4 + 8 has the highest contact force value of 2454.33 N at 10 J, which is 90.60% higher than that of single‐layer 3DWSC. And the residual compressive strength of 3DWSC‐4 + 8 maintains 91.30% after 10 J energy impact, while the retention value of single‐layer 3DWSC is only 68.43%. The above results can be attributed to the fact that the addition of the middle panel in double‐layer 3DWSC is benefical to improve the capacity of the material to withstand transverse load or bending moment and to absorb more energy through its damage compared to the single‐layer 3DWSC. In addition, the SEM images showed that only resin cracks in the double‐layer 3DWSC and no fiber breakage and delamination, indicating exceptional mechanical stability of the as‐prepared double‐layer 3DWSC. This work can serve as a reference for the design and fabrication to multi‐layer 3DWSC, a promising material in the field of high‐performance composites.

Failure Mechanisms and Constitutive Model of Composite Rock under Dynamic Loading

Abstract In order to investigate the dynamic response characteristics of composite rock with different joint angles, static compression test and dynamic impact test are carried out using WDW-300E servo pressure-testing machine and split Hopkinson pressure bar (SHPB) test system. The dynamic compressive strength, energy dissipation, and failure modes are compared between rock coal (R-C) and coal rock (C-R). Furthermore, a 3D SHPB simulation system is constructed using coupling finite difference method and discrete element method (FDM-DEM) to reproduce the energy evolution and failure modes of composite rock with different joint angles, and the fabric tensor is obtained based on secondary development. Finally, a constitutive model of composite rock is established considering joint angles. The results of experiment, simulation, and theoretical analysis show that for the case of uniaxial compression test, with the increase of joint angle, the peak stress of composite rock shows obvious U-shaped change, and the elastic modulus increases gradually while the peak strain decreases gradually. For the case of dynamic impact test, the peak stress, strain, and energy dissipation values of composite rock decrease first and then increase with the increase of angle, and the elastic modulus of composite rock increases monotonically after a slight fluctuation of 30°. The stress, energy dissipation and elastic modulus of composite rock R-C are larger than that of composite rock C-R. However, the strain value of composite rock R-C is generally less than of composite rock C-R. The failure mode of composite rock with small and large angle is mainly splitting under dynamic impact, and the fracture fragmentation is relatively small with high energy absorption rate, while the fracture fragmentation is mainly shear and splitting mixed failure with low energy absorption rate. The energy accumulation and transformation process inside the composite rock are analyzed by 3D simulation system, and the damage of the composite rock under impact is mainly concentrated on the coal side, and peak values of contact number and contact force with different joint angles are calculated by using fabric tensor. Based on Weibull distribution, a constitutive model of composite rock is constructed considering initial damage and dynamic failure effect, which is in good agreement with experimental and simulation results, verifying the correctness of the constructed model.