Vacancy Defects Research Articles

Material Engineering Strategies for Efficient Hydrogen Evolution Reaction Catalysts.

Water electrolysis, a key enabler of hydrogen energy production, presents significant potential as a strategy for achieving net-zero emissions. However, the widespread deployment of water electrolysis is currently limited by the high-cost and scarce noble metal electrocatalysts in hydrogen evolution reaction (HER). Given this challenge, design and synthesis of cost-effective and high-performance alternative catalysts have become a research focus, which necessitates insightful understandings of HER fundamentals and material engineering strategies. Distinct from typical reviews that concentrate only on the summary of recent catalyst materials, this review article shifts focus to material engineering strategies for developing efficient HER catalysts. In-depth analysis of key material design approaches for HER catalysts, such as doping, vacancy defect creation, phase engineering, and metal-support engineering, are illustrated along with typical research cases. A special emphasis is placed on designing noble metal-free catalysts with a brief discussion on recent advancements in electrocatalytic water-splitting technology. The article also delves into important descriptors, reliable evaluation parameters and characterization techniques, aiming to link the fundamental mechanisms of HER with its catalytic performance. In conclusion, it explores future trends in HER catalysts by integrating theoretical, experimental and industrial perspectives, while acknowledging the challenges that remain.

SnSe2 Quantum Dots and Chlorhexidine Acetate Suppress Synergistically Non-radiative Recombination Loss for High Efficiency and Stability Perovskite Solar Cells.

Non-radiative recombination losses limit the property of perovskite solar cells (PSCs). Here, a synergistic strategy of SnSe2QDs doping into SnO2 and chlorhexidine acetate (CA) coating on the surface of perovskite is proposed. The introduction of 2D SnSe2QDs reduces the oxygen vacancy defects and increases the carrier mobility of SnO2. The optimized SnO2 as a buried interface obviously improves the crystallization quality of perovskite. The CA containing abundant active sites of ─NH2/─NH─, ─C═N, CO, ─Cl groups passivate the defects on the surface and grain boundary of perovskite. The alkyl chain of CA also improves the hydrophobicity of perovskite. Moreover, the synergism of SnSe2QDs and CA releases the residual stress and regulates the energy level arrangement at the top and bottom interface of perovskite. Benefiting from these advantages, the bulk and interface non-radiative recombination loss is greatly suppressed and thereby increases the carrier transport and extraction in devices. As a result, the best power conversion efficiency (PCE) of 23.41% for rigid PSCs and the best PCE of 21.84% for flexible PSCs are reached. The rigid PSC maintains 89% of initial efficiency after storing nitrogen for 3100 h. The flexible PSCs retain 87% of the initial PCE after 5000 bending cycles at a bending radius of 5 mm.

Vertically Oriented Quasi-2D Perovskite Grown In-Situ by Carbonyl Array-Synergized Crystallization for Direct X-Ray Detectors.

Quasi-2D perovskite quantum wells are increasingly recognized as promising candidates for direct-conversion X-ray detection. However, the fabrication of oriented and uniformly thick quasi-2D perovskite films, crucial for effective high-energy X-ray detection, is hindered by the inherent challenges of preferential crystallization at the gas-liquid interface, resulting in poor film quality. In addressing this limitation, a carbonyl array-synergized crystallization (CSC) strategy is employed for the fabrication of thick films of a quasi-2D Ruddlesden-Popper (RP) phase perovskite, specifically PEA2MA4Pb5I16. The CSC strategy involves incorporating two forms of carbonyls in the perovskite precursor, generating large and dense intermediates. This design reduces the nucleation rate at the gas-liquid interface, enhances the binding energies of Pb2+ at (202) and (111) planes, and passivates ion vacancy defects. Consequently, the construction of high-quality thick films of PEA2MA4Pb5I16 RP perovskite quantum wells is achieved and characterized by vertical orientation and a pure well-width distribution. The corresponding PEA2MA4Pb5I16 RP perovskite X-ray detectors exhibit multi-dimensional advantages in performance compared to previous approaches and commercially available a-Se detectors. This CSC strategy promotes 2D perovskites as a candidate for next-generation large-area flat-panel X-ray detection systems.

Nickel–Nitrogen–Carbon (Ni–N–C) Electrocatalysts Toward CO2 electroreduction to CO: Advances, Optimizations, Challenges, and Prospects

Electrocatalytic reduction of CO2 into high energy‐density fuels and value‐added chemicals under mild conditions can promote the sustainable cycle of carbon and decrease current energy and environmental problems. Constructing electrocatalyst with high activity, selectivity, stability, and low cost is really matter to realize industrial application of electrocatalytic CO2 reduction (ECR). Metal–nitrogen–carbon (M–N–C), especially Ni–N–C, display excellent performance, such as nearly 100% CO selectivity, high current density, outstanding tolerance, etc., which is considered to possess broad application prospects. Based on the current research status, starting from the mechanism of ECR and the existence form of Ni active species, the latest research progress of Ni–N–C electrocatalysts in CO2 electroreduction is systematically summarized. An overview is emphatically interpreted on the regulatory strategies for activity optimization over Ni–N–C, including N coordination modulation, vacancy defects construction, morphology design, surface modification, heteroatom activation, and bimetallic cooperation. Finally, some urgent problems and future prospects on designing Ni–N–C catalysts for ECR are discussed. This review aims to provide the guidance for the design and development of Ni–N–C catalysts with practical application.

Influence of Ti Vacancy Defects on the Dissolution of O-Adsorbed Ti(0001) Surface: A First-Principles Study

Influence of Ti Vacancy Defects on the Dissolution of O-Adsorbed Ti(0001) Surface: A First-Principles Study

Chemical Potential Analysis as an Alternative to the van't Hoff Method: Hypothetical Limits of Solar Thermochemical Hydrogen.

The van't Hoff method is a standard approach for determining reaction enthalpies and entropies, e.g., in the thermochemical reduction of oxides, which is an important process for solar thermochemical fuels and numerous other applications. However, by analyzing the oxygen partial pressure pO2, e.g., as measured by thermogravimetric analysis (TGA), this method convolutes the properties of the probe gas with the solid-state properties of the examined oxides, which define their suitability for specific applications. The "chemical potential method" is here proposed as an alternative. Using the oxygen chemical potential ΔμO instead of pO2 for the analysis, this method does not only decouple gas-phase and solid-state contributions but also affords a simple and transparent approach to extracting the temperature dependence of the reduction enthalpy and entropy, which carries important information about the defect mechanism. For demonstration of the approach, this work considers three model systems; (1) a generic oxide with noninteracting, charge-neutral oxygen vacancy defects, (2) Sr0.86Ce0.14MnO3(1-δ) alloys with interacting vacancies, and (3) a model for charged vacancy formation in CeO2, which reproduces the extensive experimental TGA data available in the literature. The reduction behavior of these model systems obtained from the chemical potential method is correlated with simulated results for the thermochemical water splitting cycle, highlighting the exceptional behavior of CeO2, which originates from defect ionization. The theoretical performance limits for solar thermochemical hydrogen within the charged defect mechanism are assessed by considering hypothetical materials described by a variation of the CeO2 model parameters within a plausible range.

Accumulation of Long-Lived Photogenerated Holes at Indium Single Atom Catalysts via Two Coordinate Nitrogen Vacancy Defect Engineering for Enhanced Photocatalytic Oxidation.

Visible light-driven photocatalytic oxidation by photogenerated holes has immense potential for environmental remediation applications. While the electron-mediated photoreduction reactions are often at the spotlight, active holes possess a remarkable oxidation capacity that can degrade recalcitrant organic pollutants, resulting in non-toxic byproducts. However, the random charge transfer and rapid recombination of electron-hole pairs hinder the accumulation of long-lived holes at the reaction center. Herein, we report a novel method employing defect-engineered indium (In) single atom photocatalysts, dispersed in carbon nitride foam (In-Nv-CNF), to overcome these challenges and make further advances in photocatalysis. This Nv (nitrogen vacancy) defect-engineered strategy produces a remarkable extension in the lifetime of photogenerated holes and an increase in the concentration of photogenerated holes in In-Nv-CNF. Consequently, the optimized In-Nv-CNF demonstrates a remarkable 50-fold increase in photo-oxidative degradation rate compared to pristine CN, effectively breaking down two widely used antibiotics (tetracycline and ciprofloxacin) under visible light. The contaminated water treated by In-Nv-CNF has proven to be completely non-toxic based on the growth of E. coli before and after treatment. Structural-performance correlations between Nv defect engineering and long-lived hole accumulation in In-Nv-CNF are established and validated through experimental and theoretical agreement. This work has the potential to elevate the efficiency of overall photocatalytic reactions from a hole-centric standpoint. This article is protected by copyright. All rights reserved.

Unveiling the CoFe LDH generated by partial in situ conversion strategy: Synergistic effect of modified MXene and cationic vacancies for overall water splitting

It remains a challenge to utilize non-precious metal electrocatalysts to increase intrinsic activity and observe more active sites. Herein, we propose a simple partial in situ transformation strategy to form a novel MOF@CoFe LDH heterostructure by Co-MOF template-directed fabrication using modified MXene as substrate, and introduce metal cation vacancy defects on the as-prepared LDH surface to further enhance the performance of the catalysts. Density-functional theory calculations show that the electron transfer rate of a material can be tuned by modulating the electron diffusion phenomenon, thereby lowering the energy barrier of the catalytic reaction. Consistent with the expected results, the catalysts also showed excellent electrochemical performance with HER and OER reaching current densities of 10 mA cm−2 with overpotentials of only 201 mV and 197 mV, and Faraday efficiencies (FE) close to 100 %. Meanwhile, a cell overpotential of only 1.56 V is required to effectively drive a current density of 10 mA cm−2 in the two-electrode system, and the superior long-term stability of the material reveals its potential for cost reduction in large-scale industrial applications.

Hydrogen evolution descriptors of 55-atom PtNi nanoclusters and interaction with graphite

Density functional simulations have been performed for Pt n Ni 55−n clusters ( n=0,12,20,28,42,55 ) to investigate their catalytic properties for the hydrogen evolution reaction (HER). Starting from the icosahedral Pt12Ni43 , hydrogen adsorption energetics and electronic d-band descriptors indicate HER activity comparable to that of pure Pt55 (distorted reduced core structure). The PtNi clusters accommodate a large number of adsorbed hydrogen before reaching a saturated coverage, corresponding to 3–4 H atoms per icosahedron facet (in total ∼70–80). The differential adsorption free energies are well within the window of |ΔGH|<0.1 eV which is considered optimal for HER. The electronic descriptors show similarities with the platinum d-band, although the uncovered PtNi clusters are magnetic. Increasing hydrogen coverage suppresses magnetism and depletes electron density, resulting in expansion of the PtNi clusters. For a single H atom, the adsorption free energy varies between −0.32 ( Pt12Ni43 ) and −0.59 eV ( Pt55 ). The most stable adsorption site is Pt–Pt bridge for Pt-rich compositions and a hollow site surrounded by three Ni for Pt-poor compositions. A hydrogen molecule dissociates spontaneously on the Pt-rich clusters. The above HER activity predictions can be extended to PtNi on carbon support as the interaction with a graphite model structure (w/o vacancy defect) results in minor changes in the cluster properties only. The cluster-surface interaction is the strongest for Pt55 due to its large facing facet and associated van der Waals forces.

MoS2@MWCNTs with Rich Vacancy Defects for Effective Piezocatalytic Degradation of Norfloxacin via Innergenerated-H2O2: Enhanced Nonradical Pathway and Synergistic Mechanism with Radical Pathway.

Molybdenum disulfide (MoS2)-based materials for piezocatalysis are unsatisfactory due to their low actual piezoelectric coefficient and poor electrical conductivity. Herein, 1T/3R phase MoS2 grown in situ on multiwalled carbon nanotubes (MWCNTs) was proposed. MoS2@MWCNTs exhibited the interwoven morphology of thin nanoflowers and tubes, and the piezoelectric response of MoS2@MWCNTs was 4.07 times higher than that of MoS2 via piezoresponse force microscopy (PFM) characterization. MoS2@MWCNTs exhibited superior activity with a 91% degradation rate of norfloxacin (NOR) after actually working 24 min (as for rhodamine B, reached 100% within 18 min) by pulse-mode ultrasonic vibration-triggered piezocatalysis. It was found that piezocatalysis for removing pollutants was attributed to the synergistic effect of free radicals (•OH and O2•-) and nonfree radical (1O2, key role) pathways, together with the innergenerated-H2O2 promoting the degradation rate. 1O2 can be generated by electron transfer and energy transfer pathways. The presence of oxygen vacancies (OVs) induced the transformation of O2 to 1O2 by triplet energy transfer. The fast charge transfer in MoS2@MWCNTs heterostructure and the coexistence of sulfur vacancies and OVs enhanced charge carrier separation resulting in a prominent piezoelectric effect. This work opens up new avenues for the development of efficient piezocatalysts that can be utilized for environmental purification.

Preparation of SnS2/MoS2 with p-n heterojunction for NO2 sensing

Abstract Conventional metal sulfide (SnS2) gas-sensitive sensing materials still have insufficient surface area and slow response/recovery times. To increase its gas-sensing performance, MoS2 nanoflower was produced hydrothermally and mechanically combined with SnS2 nanoplate. Extensive characterization results show that MoS2 was effectively integrated into SnS2. Four different concentrations of SnS2-MoS2 composites were evaluated for their NO2 gas sensitization capabilities. Among them, SnS2-15% MoS2 at 170 °C demonstrated the greatest response values to NO2, 7.3 for 1 ppm NO2, which is about three times greater than the SnS2 sensor at 170 °C (2.58). The creation of pn junctions following compositing with SnS2 was determined to be the primary reason for the composite's faster recovery time, while the heterojunction allowed for the rapid separation of hole-electron pairs. Because the MoS2 surface has multiple vacancy defects, the adsorption energy of these vacancies is significantly higher than that of other places, resulting in increased NO2 adsorption. Furthermore, MoS2 can serve as active adsorption sites for SnS2 micrometer sheets during gas sensing. This study may help to build new NO2 gas sensors.

Improving Hybrid Tin Halide Films by Tin Trifluoromethanesulfonate for Lead-Free Perovskite Solar Cells.

Tin-based perovskite solar cells (Sn-PSCs) without toxic lead ions outperform other types of lead-free PSCs in terms of photovoltaic performance. To avoid the oxidation of Sn2+ cations and the formation of vacancy defects, most reports involve the addition of SnF2 to the perovskite precursor solution, but hybrid tin halide (Sn-PVK) films still suffer from poor crystallinity and stability. In this work, we used an alternative additive of tin trifluoromethanesulfonate (Sn(OTF)2). Compared to SnF2, the solubility of Sn(OTF)2 in the precursor solution is greatly improved, and the crystal nucleation process is delayed, resulting in the enhancement of crystal growth. The coordination ability of the OTF- anions suppresses the oxidation of Sn2+ cations, which promotes the stability of Sn-PVK films. By replacing the conventional additive of SnF2 with Sn(OTF)2, the device achieves an increase in power conversion efficiency from 7.96% to 10.3%, while the stability of the devices is improved simultaneously.

One Stone Two Birds: Anomalously Enhancing the Cross‐Plane and In‐Plane Heat Transfer in 2D/3D Heterostructures by Defects Engineering

AbstractThis study addresses a crucial challenge in two‐dimensional (2D) material‐based electronic devices—inefficient heat dissipation across the van der Waals (vdW) interface connecting the 2D material to its three‐dimensional (3D) substrate. The objective is to enhance the interfacial thermal conductance (ITC) of 2D/3D heterostructures without compromising the intrinsic thermal conductivities (κ) of 2D materials. Using 2D‐MoS2/3D‐GaN as an example, a novel strategy to enhance both the ITC across 2D/3D interface and κ of 2D material is proposed by introducing a controlled concentration (ρ) of vacancy defects to substrate's bottom surface. Molecular dynamics simulations demonstrate a notable 2.1‐fold higher ITC of MoS2/GaN at ρ = 4% compared to the no‐defective counterpart, along with an impressive 56% enhancement in κ of MoS2 compared to the conventional upper surface modification approaches. Phonon dynamics analysis attributes the ITC enhancement to increased phonon coupling between MoS2 and GaN, resulting from polarization conversion and hybridization of phonons at the defective surface. Spectral energy density analysis affirms that the improved κ of MoS2 directly results from the proposed strategy, effectively reducing phonon scattering at the interface. This work provides an effective approach for enhancing heat transfer in 2D/3D vdW heterostructures, promisingly advancing electronics’ heat dissipation.

Integrated Heterogeneous Engineering with the Vacancy Defect of Porous CoPv-MoxPv Nanosheets for an Accelerated Hydrogen Evolution Reaction.

Electrochemical water splitting is a possible way of realizing sustainable and clean hydrogen production but is challenging, because a highly active and durable electrocatalyst is essential. In this work, we integrated heterogeneous engineering and vacancy defect strategies to design and fabricate a heterostructure electrocatalyst (CoPv-MoxPv/CNT) with abundant phosphorus vacancies attached to carbon nanotubes (CNTs). The vacancy defects enabled the optimization of the electronic structure; thereby, the electron-rich low-valent metal sites enhanced the ability of nonmetallic P to capture proton H. Meanwhile, the heterogeneous interface between bimetallic phosphides and CNTs realized rapid electron transfer. In addition, the Co, Mo, and P active species in the electrocatalytic process exposed increased amounts of active sites featuring porous nanosheet structures, which facilitated the adsorption of reaction intermediates and thus enhanced the hydrogen evolution reaction performance. In particular, the optimized CoPv-MoxPv/CNT catalyst possesses an overpotential of 138 mV at a current density of 10 mA cm-2 and long-term stability for 24 h. This work offers insights and possibilities for the engineering and exploration of transition metal-based electrocatalysts through combining multiple synergistic strategies.

Effects of Intrinsic Defects in Pt-Based Carbon Supports on Alkaline Hydrogen Evolution Reaction.

Carbon material has widely been utilized in the synthesis of efficient carbon-supported Pt (Pt/C) catalysts, in which the structural properties greatly influence the electrocatalytic performances of Pt/C catalysts. However, the effects of intrinsic defects in carbon supports on the performance of the alkaline hydrogen evolution reaction (HER) have not been systematically investigated. Herein, porous carbon supports with different degrees of intrinsic defects were prepared by a simple template-assisted strategy, and the resulting samples were systematically studied by various analytical methods. The results suggested that the presence of abundant intrinsic defects (vacancy and topological defects) in the carbon support was advantageous in terms of favoring the dispersion and anchoring of Pt species, promoting electron transfer between Pt atoms and the carbon support, and tuning the electronic states of Pt species. These features improved the HER performance of Pt/C catalysts. Compared to the nontemplate-assisted carbon-supported Pt catalyst (Pt/NTC) with an overpotential of 178 mV, the optimized template-assisted carbon-supported Pt catalyst (Pt/TC) exhibited a lower overpotential of 58 mV at 10 mA cm-2. Besides, the Pt/TC catalyst displayed better HER durability than the Pt/NTC catalyst owing to its strong metal-support interaction. The DFT calculations confirmed the important role played by intrinsic defects (vacancy and topological defects) in stabilizing Pt atoms, with Pt-C3 coordination identified as the most favorable structure for improving the HER performance of Pt. Overall, novel insights on the significant contribution of intrinsic defects in porous carbon supports on the HER performances of Pt/C catalysts were provided, useful for future design and fabrication of advanced carbon-supported catalysts or other carbon-based electrode materials.

Nitrided Copper-Iron Composite Oxides Derived from Layered Double Hydroxides for Enhanced Carbon Dioxide Electroreduction to Methane and Formic Acid

The reduction of carbon dioxide to valuable chemical products is a promising solution to address carbon balance and energy issues. Herein, amorphous nitrided copper-iron oxides are prepared by gas-phase nitriding of CuFe-layered double hydroxide precursors with urea as nitrogen source. Amorphous materials are more likely to generate defect vacancies during the reaction process, and these vacancies can function as active sites for catalytic reactions. Therefore, the obtained materials show high activity for CO2 electroreduction to methane and formic acid, achieving a total Faraday efficiency of 74.7% at −0.7 V vs RHE and exhibiting a continuous 10 h durability in the H-cell. The uniformly distributed Cu+ sites act as active sites by losing electrons to activate CO2. During the CO2 electroreduction, CO2 is converted to *COOH via proton-electron coupling, *COOH combines directly with a proton in solution to produce the HCOOH product, and the other part of *COOH undergoes a protonated dehydration process to form the *CHO intermediate which dehydrates again to form CH4. This study provides a new approach for designing CO2 electroreduction catalysts.

Hydrogen permeation of single layer graphene with substitutional metal impurity defects

Two-dimensional materials have recently emerged as promising candidates for blocking hydrogen isotopes, with pristine graphene showing the most promising attributes. Nevertheless, synthesized graphene typically harbors various defects. In this study, we conducted a systematic investigation employing a first-principles approach to assess the permeation of hydrogen through single-layer graphene featuring a single-atom vacancy and diverse substitutional metal impurity defects. Our findings indicate that most substitutional metal impurities in a carbon vacancy effectively enhance graphene's ability to obstruct hydrogen when it harbors vacancy defects, resulting in elevated hydrogen penetration barriers in contrast to graphene with a single-atom vacancy. The hydrogen penetration barriers are contingent upon both the atomic size and the number of outermost electrons in the metal defects. Transition metals characterized by larger atoms and more outermost electrons exhibit heightened penetration barriers, while non-transition metals exhibit a relatively diminished impact of outermost electrons on hydrogen penetration barriers due to reduced charge transfer to graphene. This study underscores the pivotal role played by metal defects in obstructing the infiltration of hydrogen and its isotopes into graphene.

Anion Binding Interaction Enhances the Robustness of Iodide for High-Performance Perovskite Solar Cells.

Owing to the ionic bond nature of the Pb-I bond, the iodide at the interface of perovskite polycrystalline films was easily lost during the preparation process, resulting in the formation of a large number of iodine vacancy defects. The presence of iodine vacancy defects can cause nonradiative recombination, provide a pathway for iodide migration, and be harmful to the power conversion efficiency (PCE) and stability of organic-inorganic hybrid perovskite solar cells (HPSCs). Here, in order to increase the robustness of iodides at the interface, a strategy to introduce anion binding effects was developed to stabilize the perovskite films. It was demonstrated that the N,N'-diphenylurea (DPU), characterized by high anionic binding constants and a Y-shaped structure, provides a relatively strong hydrogen bond donor site to effectively reduce the iodine loss during film preparation and inhibits iodide migration in the device working condition. As expected, the reduced iodine loss considerably improves the quality of the perovskite films and suppresses nonradiative recombination. The performance of the device after DPU modification was significantly increased, with the PCE rising from 23.65 to 25.01% with huge stability enhancement as well.

Efficient pure-red perovskite light-emitting diodes with strong passivation via ultrasmall-sized molecules.

Perovskite light-emitting diodes (PeLEDs) have attracted great attention in recent years; however, the halogen vacancy defects in perovskite notably hamper the development of high-efficiency devices. Previously, large-sized passivation agents have been usually used, while the effect of defect passivation is limited due to the weak bonding or the large space steric hindrance. Here, we predict that the ultrasmall-sized formate (Fa) and acetate (Ac) have more efficient passivation ability because of the stronger binding with the perovskite, as demonstrated by density functional theory calculation. We introduce ultrasmall-sized cesium salts (CsFa/CsAc) into buried interface, which can also diffuse into the bulk, resulting in both buried interface and bulk passivation. In addition, the improved perovskite growth has been found due to the enhanced hydrophily after introducing CsFa/CsAc as additive. According to these advantages, a pure-red PeLED with 24.2% efficiency at 639 nm has been achieved.

Bifunctional passivation by lewis-base molecules for efficient printable mesoscopic perovskite solar cells

Printable mesoscopic perovskite solar cells (PM-PSCs) possess notable merits in terms of cost-effectiveness, easy manufacturing, and large scale applications. Nevertheless, the absence of a hole transport layer contributes to the exacerbation of carrier recombination, and the defects between the perovskite and electron transport layer (ETL) interfaces significantly decrease the efficiency of the devices. In this study, a bifunctional surface passivation approach is proposed by applying a thioacetamide (TAA) surfactant on the mesoporous TiO2 interface. The results demonstrate that TAA molecules could interact with TiO2, thereby diminishing the oxygen vacancy defects. Additionally, the amino group and sulfur atoms in TAA molecules act as Lewis base to effectively passivate the uncoordinated Pb2+ in perovskite and improve the morphology of perovskite, and decrease the trap-state density of perovskite. The TAA passivation mechanism improves the alignment of energy levels between TiO2 and perovskite, facilitating electron transport and reducing carrier recombination. Consequently, the TAA-passivated device achieved a champion power conversion efficiency (PCE) of 17.86% with a high fill factor (FF) of 79.16% and an open-circuit voltage (VOC) of 0.971 V. This investigation presents a feasible strategy for interfacial passivation of the ETL to further improve the efficiency of PM-PSCs.