Use Of 3D Printing Technology Research Articles

Application of 3D printing in the treatment of diabetic foot ulcers: current status and new insights

Background and AimsDiabetic foot ulcers (DFUs) are a serious complication of diabetes mellitus (DM), affecting around 25% of individuals with DM. Primary treatment of a DFU involves wound off-loading, surgical debridement, dressings to provide a moist wound environment, vascular assessment, and appropriate antibiotics through a multidisciplinary approach. Three-dimensional (3D) printing technology is considered an innovative tool for the management of DFUs. The utilization of 3D printing technology in the treatment of DFU involves the modernization of traditional methods and the exploration of new techniques. This review discusses recent advancements in 3D printing technology for the application of DFU care, and the development of personalized interventions for the treatment of DFUs.MethodsWe searched the electronic database for the years 2019–2024. Studies related to the use of 3D printing technology in Diabetic foot were included.ResultsA total of 25 identified articles based on database search and citation network analysis. After removing duplicates, 18 articles remained, and three articles that did not meet the inclusion criteria were removed after reading the title/abstract. A total of 97 relevant articles were included during the reading of references. In total, 112 articles were included.Conclusion3D printing technology offers unparalleled advantages, particularly in the realm of personalized treatment. The amalgamation of traditional treatment methods with 3D printing has yielded favorable outcomes in decelerating the progression of DFUs and facilitating wound healing. However, there is a limited body of research regarding the utilization of 3D printing technology in the domain of DFUs.

Learning program enhances rehabilitation professionals’ perceived ease of using 3d printing: a pilot randomized controlled trial

The pilot study evaluated whether a learning program enhances a positive perception of 3D printing technology in rehabilitation professionals. Physical therapists, occupational therapists and speech-language-hearing therapists were recruited from a rehabilitation department in a middle-sized hospital. Participants were randomized to the control group (n = 13) or the intervention group (n = 14). An eight-week learning program consisted of a lecture on using a 3D printer and related software, a group discussion to integrate 3D printing into their clinical practices, and the implementation in their workplace. Outcome measures included the perception of 3D printing technology assessed by the Japanese version of the modified Technology Acceptance Model questionnaire for 3D printing technology (TAM-J). Assessment time points were pre-and post-intervention. As a result, all participants in the intervention group became capable of producing 3D-printed customized assistive devices. In the within-group analyses, the intervention group showed significant improvements in the TAM-J perception ease of use score (p = 0.012) with a large effect size (r = 0.75). Between-group analyses showed that the intervention group gained an additional improvement in the TAM-J perception ease of use score (p = 0.027) with a moderate effect size (r = 0. 43), indicating a significant improvement in the perceived ease of use of 3D printing technology in the intervention group. These observations suggest the 3D printing learning program could provide rehabilitation professionals with a positive perception of the technical aspect of 3D printing in their workplace.

Review of strategies to overcome the lack of data in landmine detection

This article reviews strategies to address the lack of data for training landmine recognition models. Since the outbreak of the war in Ukraine in 2014, the area of contaminated territories has gradually increased. However, after Russia's full-scale invasion on February 24, 2022, the problem of landmines in Ukraine has become much more severe, as the area of mined territories in the country has increased to 30%. It takes many years and efforts to clear such a large area. To overcome a problem of this scale, it is necessary to look for new methods of landmine detection that will allow demining to be conducted 24/7. Machine learning is one of the options for solving the problem of landmine detection. To train landmine recognition models, a large amount of data is required. However, the lack of diverse and large datasets creates significant obstacles to the development of effective detection systems. The safety concerns associated with conducting experiments with real landmines further exacerbate the problem. This article discusses three possible strategies to overcome the above problem: augmentation methods, the use of 3D printing technology, and crowdsourced data collection. Augmentation methods offer data generation to improve model performance. 3D printing allows for the creation of realistic replicas of landmines for safe experimentation. Crowdsourcing uses collective efforts to collect real-world data from conflict zones. Through the joint efforts of researchers, technology developers and humanitarian organizations, these approaches offer promising ways to improve landmine detection capabilities. The use of these approaches can address the data gap and ensure safe data collection.

Manufacturing of a 3D-printed electrode cost-effective based on carbon black and polylactic acid for detection of flunixin anti-inflammatory

This study presents the manufacturing and application of a 3D-printed sensor based on CB/PLA for detecting the anti-inflammatory drug flunixin (FXN). The proposed sensor features a simple design and accessible construction process with fast production (∼25 min), fast activation (∼400 s), low cost (∼0.044 USD), and stands out for its sensitivity (0.083 µA µmol l-1) and low detection limit (0.30 µmol l-1). Furthermore, the sensor presents allowed the determination of the FXN in real samples such as pharmaceutical formulations (tablet and injectable), tap and river water without pretreatment. The selectivity obtained was satisfactory in the presence of metal ions and organic compounds. The results showed that the use of 3D printing technology with fast surface treatment made it possible to study the anti-inflammatory behavior of FXN in a satisfactory way. Therefore, it is pertinent to use 3D technology in electrochemical analyses of potential antibiotics and other pharmaceuticals.

A Mini Review on the Opportunities for Membrane Pervaporation Technology for Energy-efficient Removal of Dispersed Oil and Dissolved Hydrocarbons from Produced Water

Produced water is reported to have the largest volume of waste stream associated with hydrocarbon recovery. It was estimated to increase from 250 million B/D in 2007 to more than 300 million B/D between 2010 and 2012. Market research conducted by Adroit put the globally produced water treatment market at a value of USD 5.10 billion in 2022. This value is anticipated to be USD 9.80 billion in 2032 at a compound annual growth rate (CAGR) of 5.80% over the prediction period. Oil and gas companies have been mandated to comply with the newly enacted environmental regulations that require extensive treatment of this water before discharge or reuse. The limited quantity of freshwater resources coupled with the increasing oil and gas production activities has made it necessary for all stakeholders to look for sustainable management of this water. Presently, a certain percentage of produced water is reused while the rest is discharged into the ocean. In both cases, the water needs to be thoroughly treated. The choice of technologies for produced water treatment depends on numerous factors, such as the chemical composition of the water and the level of purity that must be attained before disposal, recycling, or re-use. Some of the technologies used for produced water treatment include physical separation methods such as gravity, adsorption, filtration, coalescence, cyclones, flotation, centrifuges, membranes, and oxidation. There are also chemical and biological separation methods. Contaminants such as small droplets of dispersed oil and dissolved hydrocarbons (DODHs) are very challenging to remove using the above-listed water treatment technologies. Moreover, the use of membrane technology has been limited only to the use of reverse osmosis and membrane filtration for removing salinity, metals, and other inorganics. This article highlights the opportunities for the use of membrane vapor permeation and pervaporation for the removal of the small droplets of DODHs, which have been reported to be very challenging contaminants to remove. The use of 3D printing technology for the fabrication of membrane materials was reviewed. The 3D membrane development method can be used to fabricate almost any shape of the material in a highly customized manner using computer-aided design. The information presented in this article will serve as a useful reference for the technologies used for a sustainable water treatment strategy in the oil and gas industry.

An Algorithm for Coding an Additive Manufacturing File from the Pressure Distribution of a Baropodometric Board for 3D Printing Customised Orthopaedic Insoles

Customised orthotic insoles play a critical role in addressing foot pathologies and improving comfort and biomechanical alignment for patients with specific needs. The use of 3D printing technology for the manufacturing of orthotic insoles has received considerable attention in recent years due to its potential for customisation, rapid prototyping, and cost-effectiveness. This paper presents the implementation of an algorithm purposely developed to generate an Additive Manufacturing File (AMF) containing the geometry of a patient-specific insole and the stiffness distribution based on pressure analysis from a baropodometric board. The generated file is used to 3D print via Fused Deposition Modelling an insole with a variable infill percentage depending on the pressure distribution on the patient’s foot. Three inputs are used as source data for the AMF file coding: (i) the 3D model that defines the geometry of the insole designed by the orthopaedist; (ii) the pressure map of the patient’s feet obtained with a baropodometric board; and (iii) the stiffness of the material that will be used to fabricate the insole. The proposed approach allows the fabrication of a patient-specific insole, capable of restoring the correct pressure distribution on the foot by varying the infill percentage. Two types of insoles were successfully fabricated using the implemented algorithm: the first was 3D printed, adding a top layer to be ready-to-use; the second was 3D printed without a top surface to be further customised with different coatings. The method described in this paper is robust for the fabrication of customised insoles and aims at overcoming the limitations of the traditional approach based on milling machining (e.g., time, costs, and path planning) since it can be easily integrated into any orthopaedic workshop.

342. BILATERAL THORACOSCOPIC APPROACH FOR ADVANCED ESOPHAGEAL CANCER COMPLICATED WITH DOUBLE AORTIC ARCH (DAA)

Abstract Background Double aortic arch (DAA) is a relatively rare vascular malformation that causes few problems in adults. However, the presence of DAA makes esophageal cancer surgery difficult, especially during upper mediastinal dissection. Here we report a bilateral thoracoscopic surgical technique in a patient with highly advanced esophageal cancer complicated with DAA. Case 73-year-old male, cT3N4M0 stage III (UICC-TNM 7th) mid-thoracic esophageal cancer with DAA was diagnosed. After two courses of neoadjuvant chemotherapy, surgical treatment was planned. To develop a surgical strategy for esophagectomy for this complex malformation, we created a 3D printer model of the case. The results suggested that a bilateral thoracoscopic approach in the prone position was the ideal approach for upper mediastinal dissection. As expected, it was difficult to dissect the upper mediastinum using only a right-sided approach, especially on the esophagus oral side behind the right aortic arch (RAA), where dissection from the right side was impossible. By adding a left lateral approach, the oral side of the esophagus was pulled in from the left aortic arch (LAA) and was easily dissected. The operation was successful and the postoperative course was uneventful. In this presentation, we will demonstrate the technique of bilateral approach for advanced esophageal cancer complicated with DAA. Discussion The surgical strategy for patients with thoracic esophageal cancer and a coexisting complex vascular anomaly known as a double aortic arch (DAA) is a highlight. Typically, surgical approaches have been limited to either left or right thoracic access. However, through preoperative simulation using 3D printing, a bilateral approach was deemed safe and effective for these cases. The 3D printer models provided invaluable insights into the anatomical relationships of blood vessels, trachea, and heart, allowing for precise planning and execution of the surgery. Challenges such as the proximity of the descending aorta to the trachea and the optimal approach angle were successfully addressed through simulation, enhancing surgical outcomes. Furthermore, the bilateral thoracoscopic approach demonstrated potential benefits in preserving delicate structures like the recurrent laryngeal nerve. This innovative use of 3D printing technology in preoperative planning represents a significant advancement in the field of gastrointestinal surgery, offering improved safety and precision for patients with complex anatomical variations like DAA. Conclusions 3D printer is useful for simulating thoracoscopic esophagectomy with macrovascular malformations. Bilateral approach is appropriate for surgery of esophageal cancer complicated with DAA and a 3D printer is a useful tool for simulating esophageal surgery.

Evaluation of wear and friction properties of graphite modified Lubri polylactic acid with various infill fabricated by additive manufacturing techniques

AbstractThree‐dimension (3D) printing technology, also known as additive manufacturing, is a manufacturing technology that creates three‐dimensional objects by depositing material layer by layer, as opposed to subtractive manufacturing methods. However, the newness of the technology brings with it many unknowns. In particular, the raw materials used are constantly increasing. For this reason, testing each raw material used in many aspects and to determine the optimum production conditions is important for the wide use of 3D printing technology. These optimal conditions may be the parameters used to produce a material, and sometimes they can appear as a new material. In addition, the production of new materials with varying production parameters is fundamental research topic that requires comprehensive study. For all these purposes, in this study, a new material type known as Lubri PLA (LPLA) was selected and produced in different filling types and subjected to a series of friction and wear tests. Thus, it is aimed to determine the tribological properties of the material. Additionally, samples were produced in ten different infill types (grid, lines, triangels, hexagon, cubic, octal, zigzag, diagonal, diagonal 3D and gyroid) to show the effect of filler type on friction and wear behavior. These filler types were used for both PLA and Lubri PLA materials and a total of twenty samples were produced. Thereby, it is aimed to conduct a comprehensive study showing the effect of both material difference and filling type on friction‐wear behavior. Diameter deviations, hardness deviations, friction coefficient, temperature, specific wear rates (SWr), and vibration were selected as output parameters. According to the analysis of the test results, the best result in terms of material structure was given by Lubri PLA, while the best result in terms of filling type was obtained with Diagonal 3D filling type. In addition, the lowest vibration level was obtained in the LP‐Diagonal 3D sample with 0.041 mm/s2, while the highest vibration level was obtained in the P‐Grid sample with 1.756 mm/s2.Highlights LPLA closed to nominal value in diameter and hardness deviations Addition of graphite nanoparticle increased the dimensional accuracy Diagonal 3D infill type Lubri PLA composites showed the superior performance Graphite modified Lubri PLA composites demonstrated superior performance

Advancing sustainable construction: Terracotta component development through extrusion-based 3d printing with local clay

This study examines the use of 3D printing technology in construction, specifically the use of local clay as the primary material for developing Terracotta components. The results demonstrate the feasibility and high print quality achievable with clay, establishing it as a viable material for 3D printing in construction. The analysis of physical properties, such as shrinkage, density, and water absorption, provides valuable insights. Thermal conductivity, also examined, contributes to a comprehensive understanding of material performance. The article identifies the optimal extrusion parameters for terracotta components. The evaluations show that the water absorption rates are within standards, and the density variation ranges from 1420 to 1466 kg/m³. Additionally, there is a direct correlation between thermal conductivity and density. The compressive strengths are diverse, ranging from 18 MPa to 33 MPa. While modulus of elasticity provides essential quantitative data for understanding the mechanical behavior of printed samples when subjected to various stresses. The internal structure significantly influences compression resistance in 3D printed bricks, emphasizing its importance in design. This research highlights the potential of 3D printing, specifically with clay, in sustainable construction. It encourages further exploration of its practical applications in the industry.

Reinforcing Efficiency of Recycled Carbon Fiber PLA Filament Suitable for Additive Manufacturing.

The use of 3D printing technology for manufacturing new products based on sustainable materials enables one to take advantage of secondary raw materials derived from recycling. This work investigates the structural performances of 3D printing composite filaments based on polylactic acid (PLA), as a matrix, reinforced by recycled carbon fiber (rCF). Carbon fibers were recovered from industrial scraps by a patented thermal process and used to produce thermoplastic composite filaments for additive manufacturing without any additional treatment and additives. The influence of the recovered carbon fiber (rCF) content on the thermal properties, mechanical properties and microstructure of the composites was studied in the range of 3-20 wt%. The recorded TGA curves exhibited a one-stage weight loss within the temperature range 290-380 °C for all samples and the residual rCF content was in good agreement with the theoretical fiber loading. The Young modulus of the extruded filaments strongly increased below a critical content (5 wt%), while at higher content the improvement was reduced. An increase in the storage modulus of 54% compared to neat PLA 3D printed sample resulted in a printed specimen with a higher rCF content. SEM images highlighted a strong rCF prevailing alignment in the direction of the extrusion flow, creating almost unidirectional reinforcement inside the filament. These findings suggest that homogeneous composite filaments reinforced with well-dispersed recycled CF without additional chemical modification and additives are suitable materials for additive manufacturing. The effect of rCF topological distribution within the material on the mechanical performances has been discussed, highlighting that the isolated fibers could efficiently transfer loads with respect to the percolated 3D network and have been correlated with the microstructure.

The history of the development of 3D printing technologies and their use in world artistic ceramics

The article is devoted to the study of the history of the emergence and development of additive technologies in world artistic ceramics. The article analyzes information on the history of the emergence of additive technologies. The principle of operation of 3D printing equipment, features of its use, the most common areas of use and materials used in 3D printing have been considered. An analysis of the specifics of the technical characteristics of 3D printers and technologies for 3D printing with ceramic masses has been shown that the use of ceramic materials as raw materials for 3D printing is a progressive trend due to the emergence of the possibility of forming ceramic objects and products that are practically indestructible reproduction and replication using traditional methods. In this article, the authors have been analyzed the advantages and disadvantages of manufacturing ceramic products by 3D printing. It has been established that the main difference between the production of three-dimensional plastic or metal elements and ceramic elements is the main feature of the ceramic manufacturing technology, namely that the printout is not a ceramic product before firing in the oven, that is, without firing, it is simply an element printed from clay materials (that is, such a printout before firing is called the "green part" – an unprocessed element). Currently, there are no 3D printers that can immediately produce ready-made ceramic products, all elements printed from ceramic materials require drying and firing. But, despite this nuance, printers that print with clay materials are called ceramic 3D printers. As 3D printing can accurately realize the creative thinking of artists and designers, 3D printing technology is increasingly used in the creation of ceramic products and contemporary ceramic works. The authors of the article emphasize that three-dimensional printing with clay provides ceramists with completely new opportunities for creating ceramic products with a complex configuration, texture, etc. Ceramic artists from all over the world are already actively using this technology in their work. Therefore, part of the study is devoted to examples of the use of 3D printing technology in world artistic ceramics, as well as to the description and analysis of the most interesting achievements in this direction of creativity, according to the authors.

The history of the development of 3D printing technologies and their use in world artistic ceramics

The article is devoted to the study of the history of the emergence and development of additive technologies in world artistic ceramics. The article analyzes information on the history of the emergence of additive technologies. The principle of operation of 3D printing equipment, features of its use, the most common areas of use and materials used in 3D printing have been considered. An analysis of the specifics of the technical characteristics of 3D printers and technologies for 3D printing with ceramic masses has been shown that the use of ceramic materials as raw materials for 3D printing is a progressive trend due to the emergence of the possibility of forming ceramic objects and products that are practically indestructible reproduction and replication using traditional methods. In this article, the authors have been analyzed the advantages and disadvantages of manufacturing ceramic products by 3D printing. It has been established that the main difference between the production of three-dimensional plastic or metal elements and ceramic elements is the main feature of the ceramic manufacturing technology, namely that the printout is not a ceramic product before firing in the oven, that is, without firing, it is simply an element printed from clay materials (that is, such a printout before firing is called the "green part" – an unprocessed element). Currently, there are no 3D printers that can immediately produce ready-made ceramic products, all elements printed from ceramic materials require drying and firing. But, despite this nuance, printers that print with clay materials are called ceramic 3D printers. As 3D printing can accurately realize the creative thinking of artists and designers, 3D printing technology is increasingly used in the creation of ceramic products and contemporary ceramic works. The authors of the article emphasize that three-dimensional printing with clay provides ceramists with completely new opportunities for creating ceramic products with a complex configuration, texture, etc. Ceramic artists from all over the world are already actively using this technology in their work. Therefore, part of the study is devoted to examples of the use of 3D printing technology in world artistic ceramics, as well as to the description and analysis of the most interesting achievements in this direction of creativity, according to the authors.

Implementation of Patient-Individualized 3D-Printed Models in Undergraduate Students' Education for Various Prosthetic Treatments: A Cross-Sectional Survey Study.

Due to rapid changes in dental practice, digital technologies have become prominent in undergraduate dental education at German universities in recent years. This shift has prompted a re-evaluation of content as well as teaching methods, particularly in courses where students are prepared for patient treatment. Traditional training on standardized models with resin teeth cannot cover the complexity of individual dental arch configuration encountered in patient situations. This study explores the use of 3D printing technology to create individualized models for prosthetic treatment simulations, aiming to evaluate students' feedback towards their experience with this training setting. First, the study describes the design and fabrication of individualized models with exchangeable teeth based on intraoral scans, mounted on connected plates with distance holders that can be fixed to standard phantom heads. Second, students provided feedback through a questionnaire, assessing various aspects such as the effectiveness of the 3D-printed models compared to traditional frasaco models for preparation exercises. The results indicated that the design of the realized models was feasible for preparation training (question no. 4: 93% positive rating) and showed positive perceptions of the 3D-printed models, with students finding them effective for preparation exercises and beneficial in bridging the gap between simulation and real patient situations (question no. 6: 69% positive rating). The study suggests that 3D printing technology offers a valuable tool in dental education, providing realistic and patient-specific scenarios for students to enhance their skills and readiness for clinical practice. Further improvements in material properties in hand with cost-effective approaches are essential for widespread implementation.

New finger reconstruction technologies using 3D printing

Introduction The use of 3D printing technology in finger reconstruction improves accuracy of the procedure minimizing the donor defect and optimizing the appearance and function of the finger. The use of this technology in the finger reconstruction with an osteocutaneous radial forearm flap with axial blood supply and lengthening of the digital stumps and metacarpals remains poorly explored.The objective of the study was to demonstrate new methods of preoperative planning for finger reconstruction and improve surgical outcomes.Material and methods Outcomes of five patients treated with original methods based on 3D technology were retrospectively evaluated during preoperative planning, reconstruction of the thumb using an osteocutaneous radial forearm flap with axial blood supply, relocation of the stump of the third finger and lengthening of the stumps of the first and second metacarpals. The patients could achieve consolidation of interpositional bone allografts following lengthening of the finger stumps, stability of the bone base of the finger, organotypic restructuring of the marginal allograft during plastic surgery with an osteocutaneous radial forearm flap, and a functional position of the reconstructed thumb using the middle finger stump.Results and discussion An individual device for planning finger reconstruction allows identification of the optimal size and position of the finger in three planes, which is essential for patients with severe hand deformities to avoid corrective procedures. An individual guide was used to osteotomize the radius to harvest a vascularized graft providing a cutout of a given size and shape and a cortical-cancellous allograft being identical in shape and size to replace the donor bone defect. The combined use of Masquelet technology and distraction of the finger stump or a metacarpal improved conditions for consolidation and restructuring of the interpositional allograft preventing fractures and infection.Conclusion The use of 3D technology in finger reconstruction using an osteocutaneous radial forearm flap with axial blood supply and distraction of the finger stumps and metacarpals can improve surgical outcomes.

3D printed dosimeter incorporating leuco-crystal violet and PMMA

This paper describes the development of 3D-printed dosimeters made from radiochromic materials. Incorporating polymethyl methacrylate (PMMA) as a transparent polymer matrix and leuco-crystal violet as a radiochromic dye, these dosimeters exhibit a color change when exposed to radiation. This change provides a way to visualize and measure three-dimensional dose distributions, which is important for the accurate verification of radiation doses in radiotherapy. The use of 3D printing technology allows these dosimeters to approximate human organ geometries, which may contribute to safer and more effective radiotherapeutic applications. The dosimeters can be customized into various shapes and sizes, are lightweight, and cost-effective, making them appropriate for use in both clinical and research settings in radiotherapy. The fabrication process is detailed, and the dosimeters have been tested at doses up to 100 Gy in X-ray irradiation and analyzed for dose distribution. Bragg-peak measurements from carbon beam irradiation illustrate the dosimeters' capability to detect peak radiation doses with a spatial resolution of approximately 1 mm. These findings indicate the potential of these 3D printed dosimeters to improve the accuracy of radiation delivery, which could positively impact patient outcomes in radiotherapy.

The 3D-Printed Custom Elbow Prosthesis for Salvage Treatment of Complex Intra-Articular Distal Humerus Fracture Malunion

Intra-articular fractures of the distal humerus are complex injuries that often require surgery with the goal of restoring elbow range-of-motion and function. Open reduction and internal fixation has been the preferred surgical modality; however, restoration of the medial and/or lateral columns can be complicated in fractures involving a major loss of the articular surface and bony structure. Over the past decade, 3-dimensional (3D) printing has made significant advances in the field of orthopedic surgery, specifically in guiding surgeon preoperative planning. Recently, the incorporation of 3D-printing has proven to provide a safe and reliable construct for the restoration of anatomy in complex trauma cases. We present a 47-year-old woman who sustained a complex, intra-articular distal humerus fracture with associated shearing of the capitellum that went onto malunion. Patient was treated with a patient-specific 3D-printed custom elbow prosthesis with excellent outcomes. Our goal was to shed light on the use of 3D-printing technology as a viable salvage option in treating complex, intra-articular distal humeral fractures associated with lateral condylar damage that subsequently went onto malunion.

Experimental Study on Parameters Optimization of Selective Laser Melting 316L Stainless Steel Based on the Response Surface Methodology

Abstract The use of 3D printing technology can prepare flexible and varied special-shaped complex structures while realizing resource-saving and cost reduction. For this purpose, a 316L stainless steel sample was formed by selective laser melting technology, and the quality of samples was optimized by the Box–Behnken surface response method. Taking the surface roughness Sa as the response value, a regression analysis of four parameters of selective laser melting (laser power, scanning speed, scanning spacing, and scanning strategy) was designed using design expert software. The results showed that the scanning spacing and scanning speed have the greatest influence on the surface roughness, while the laser power and scanning strategy have no significant influence on the surface roughness. Meanwhile, the established surface roughness response surface model is effective and can be used for quality optimization of 316L structural trim. When the laser power was 185 W, the scanning speed was 615 mm/s, the scanning spacing was 110 μm and concentric scanning strategy was adopted, the surface adhesion powder was less, and the minimum surface roughness Sa was 9.001 μm.

Consumer preference and willingness to pay for 3D-printed chocolates: A discrete choice experiment

This study explores the emerging field of 3D food printing, specifically examining consumer preferences for 3D-printed chocolate bars. While 3D printing has revolutionized various industries, the consumer acceptance of 3D-printed food remains a relatively underexplored topic. A discrete choice experiment was conducted to investigate consumer preferences and willingness to pay for 3D-printed chocolate bars in the UK. Key attributes included in the study were price, chocolate type, and the use of 3D printing technology. Using a mixed logit model, preference heterogeneity was assessed, revealing a general inclination towards 3D-printed chocolates, with an estimated increase in willingness to pay of £0.21 per 100 g. Furthermore, the influence of individual (participants’) characteristics, such as age, gender, prior knowledge of 3D food printing, and food technology neophobia, on perceived benefits associated with this technology and willingness to pay was also explored, using a structural equation modeling analysis. The results indicated that only perceived hedonic benefits, such as improved texture, positively impacted the willingness to pay, while food technology neophobia acted as a significant barrier. The results of this study therefore contribute valuable insights into the consumer acceptance of 3D-printed foods, specifically chocolates, highlighting potential avenues for market adoption and emphasizing the importance of effective communication in shaping consumer attitudes toward novel food processing technologies.

Anatomical features of the proximal end of the radius and its implications for implant design.

The proximal radio-ulnar joint allows supination and pronation of the forearm and the humeroradial joint allows flexion and extension movements at the elbow joint. Although the proximal end of the radius is less common than other fractures, it is more common nowadays due to the prolongation of life expectancy, increased incidence of osteoporosis. There have been reports in the literature that success has not been achieved due to the lack of anatomical fit of the prosthesis. Knowledge of the morphometric features of the proximal end of the radius is important for the design of anatomically and biomechanically appropriate prostheses. In this study, measurements of head and neck of radius, and radial tuberosity were measured in 80 dry radii. Parameters important for prosthesis design were analysed and their correlations examined. The shapes of radial head was found 36% oval and 64% circular. The mean heights of the radial head at anterior, posterior, medial, and lateral sides were 8.52 ± 1.32mm, 9.02 ± 1.23mm, 9.20 ± 1.59mm, 8.05 ± 1.13mm, respectively. The mean depth of articular facet were 1.85 ± 0.37mm. It was determined that there was no high correlation between the parameters affecting the prosthesis design. Morphological and morphometric features of the proximal radius are important for prosthesis design and implantation. The ideal radial head prosthesis design is challenging due to numerous parameters, wide ranges and low correlation, although modular designs facilitate compatibility. The widespread use of 3D printing technologies is expected to reduce the potential complications associated with prosthesis applications.

Large artificial bone from 3D printed polycaprolactone/β-tricalcium phosphate (3D PCL/β-TCP) effectively promoting MC3T3-E1 cell adhesion, proliferation, and new bone formation

The use of 3D printing technology has advanced the bone tissue engineering, and constructing large artificial bones for repairing large-scale bone defects is highly significant. This study aimed to construct large artificial bones in a precise and controllable manner, focusing on repairing critical-sized bone defects. The researchers used 3D printing technology to synthesize 3D PCL/β-TCP, and then evaluated its ability to promote MC3T3-E1 cell adhesion, proliferation, and new bone formation through a series of characterizations. The results confirmed that 3D PCL/β-TCP, presented as a lattice structure similar to natural bone, could be used to prepare personalized artificial bone blocks based on the actual range of bone defects. The researchers also experimented with dipping 3D PCL/β-TCP bone blocks in different proportions of β-TCP and found that PT2 showed better mechanical and hydrophilic properties. Further experiments showed that PT2 presented excellent biocompatibility and outstanding capacity to promote MC3T3-E1 cell proliferation and adhesion, and that 3D PCL/β-TCP bone blocks possessed good osteogenic activity. Finally, it was suggested that PT2 exhibited the property of promoting new bone formation. These findings provide experimental data support for the repair of critical-sized bone defects.