UNS S30400 Research Articles

A Review of Welding Process for UNS S32750 Super Duplex Stainless Steel

Super duplex stainless steel UNS S32750 is widely used in marine industries, pulp and paper industries, and the offshore oil and gas industry. Welding manufacturing is one of the main manufacturing processes to make material into products in the above fields. It is of great importance to obtain high-quality welded UNS S32750 joints. The austenite content and ferrite content in UNS S32750 play an important role in determining UNS S32750 properties such as mechanical properties and corrosion resistance. However, the phase proportion between the ferrite phase and austenite phase in the welded joint will be changed during welding. Lots of research has been done on how to weld UNS S32750 and how to obtain welded joints with good quality. In this work, the recent studies on welding UNS S32750 are categorized based on the welding process. The welding process for UNS S32750 will be classified as gas tungsten arc welding, submerged arc welding, plasma arc welding, laser beam welding, electron beam welding, friction stir welding, and laser-MIG hybrid welding, and each will be reviewed in turn. The microstructure and properties of the joints welded using different welding processes will also be discussed. The critical challenge of balancing the two phases of austenite and ferrite in UNS S32750 welded joints will be discussed. This review about the welding process for UNS S32750 will provide people in the welding field with some advice on welding UNS S32750 super duplex stainless steel.

High-Temperature Deformation Behaviour of UNS S32750 Super Duplex Stainless Steel (SDSS) Alloy

In this study, the high-temperature deformation behaviour of the UNS S32750 Super Duplex Stainless Steel (SDSS) alloy was investigated by means of deformability and microstructure evolution in the (1050–1200) °C temperature (T) range. The deformability of the UNS S32750 SDSS alloy was investigated by the up-setting method using a gravity-drop hammer, with the following deformation energy/impact energy (E∗): 545.2 J, 1021.5 J, 1480.6 J, and 1905.3 J. Data referring to deformation resistance (σc′) and mechanical work (A∗) as a function of deformation temperature (T) and deformation energy/impact energy (E∗) were obtained and analysed. It was shown that increasing the deformation temperature leads to an increase in the obtained deformation degree (degree of reduction in height). By analysing the rate of increase in the deformation degree as a function of the applied impact energy, it was shown that the rate of increase in the deformation degree rises with the increase in the applied impact energy. Also, it was observed that the evolution of the deformation resistance (σc′) as a function of temperature (T) shows a decreasing tendency while increasing the deformation temperature for all impact energies and that the evolution of the mechanical work (A∗) as a function of temperature (T) shows a decreasing tendency while increasing the deformation temperature for all impact energies. The microstructure evolution of the UNS S32750 SDSS alloy was investigated by X-ray diffraction (XRD) and Scanning Electron Microscopy-Electron Backscatter Diffraction (SEM-EBSD) techniques. It was observed that, in all cases, the microstructure shows intensely deformed grains, strongly elongated in the rolling direction in both ferrite (δ) and austenite (γ) intensely deformed grains. The intensity of grain deformation is increasing with the increase in the applied deformation degree. Also, it was observed that increasing the deformation temperature leads to a strong increase in the weight fraction of the dynamically recrystallised (DRX) ferrite (δ) grains.

Flux-bound TIG welding on UNS S32760 super duplex stainless steel using activating fluxes

In this article, the effect of activating flux powders viz., Silicon Dioxide (SiO2), Chromic Oxide (Cr2O3), Titanium Dioxide (TiO2) and Vanadium Pentoxide (V2O5) on Flux-Bound TIG (FB-TIG) welding of UNS S32760 Super Duplex Stainless Steel (SDSS) is investigated. Also, conventional TIG welding is done for a comparative study with the FB-TIG welds. The macrographs of the welds are obtained to analyze the depth, width and aspect ratio. The depths obtained with all the fluxes are found to be superior relative to the conventional TIG welds. The highest penetration of 6 mm is obtained for V2O5 welds. Then the microstructure and composition of the welds are analyzed using Optical Microscopy and Area-Mapping analysis. The authors observed the presence of three forms of austenite viz., Grain Boundary Austenite, Intragranular Austenite and Widmanstatten Austenite in the weldment zones. The micro-hardness profiles of the welds are also analyzed, and the profiles obtained with all the FB-TIG welds are found to be relatively smoother without any abrupt variations. Through this investigation, it is delineated that FB-TIG welding can increase the overall productivity in the welding of SDSS, as the penetration obtained is up to thrice relative to the conventional TIG welding.

Influence of Heat Treatment Temperature on Microstructure, Hardness and Sensitization of UNS S32205 Duplex Stainless Steel

Improper thermal cycles on duplex stainless steels can lead to the formation of detrimental phases or alter the proportion of ferrite and austenite phases, thus influencing the material’s mechanical properties and corrosion resistance. Therefore, this study aimed to evaluate the effect of aging (at 850 and 950 °C) and solubilization (at 1000 and 1150 °C) thermal treatments on microstructure, indentation hardness, elasticity modulus, and susceptibility to intergranular corrosion of UNS S32205 duplex stainless steel. The sigma phase (σ) formation in the aged samples, with hardness values between 8 and 10 GPa, was confirmed. Furthermore, the pieces treated from 1000 °C upwards showed that increased temperature favored the formation of more equiaxial grains and the ferrite fraction growth. The thermal treatments barely affected the elasticity modulus of austenite and ferrite grains, increasing the hardness of ferrite. The effect of sulfuric acid concentration in the intergranular corrosion was evaluated. Also, the deconvolution of the corrosion curves permits the determination of the influence of the different phases in the corrosion performance. These tests revealed sensitization only at the σ phase grain boundaries in the samples treated at 850 °C in electrolytes containing H2SO4 2.5 mol/L and HCl 1 mol/L. Although the treatment at 950 °C led to the σ phase formation, its higher corrosion resistance was ascribed to the lower volumetric fraction of this phase, its morphology, and its increased Cr mobility compared to the 850 °C treatment. Therefore, it was shown that the σ characteristics and the sulfuric acid concentrations are determining factors in the UNS S32205 intergranular corrosion resistance.

Evaluation of Corrosion Performance of LDX 2101 and UNS S32205 in Flexible Pipeline Applications: A Comparative Study

Lean duplex stainless steel (LDSS) has been used in various applications, including flexible pipelines in offshore and other industrial settings. In recent years, LDSS has become the preferred choice over standard duplex stainless steel (DSS) for flexible pipeline applications due to its lower costs, achieved by reducing nickel and molybdenum content, while still providing comparable corrosion resistance and mechanical strength properties to DSS. However, there is still limited reporting on the corrosion effects of reducing these alloys on the behaviour of lean duplex stainless steel in flexible pipelines. This comparative study investigates the corrosion resistance of lean duplex stainless steel, LDX 2101 and duplex stainless steel, UNS S32205 in flexible pipeline applications using linear polarization resistance (LPR). The research focuses on assessing material performance in environments containing CO2 and H2S, commonly found in oil and gas production, by conducting short-term and long-term tests to evaluate pitting and selective corrosion. The samples, LDX 2101 and UNS S32205 were immersed in a 3.5M NaCl solution, and corrosion measurements were performed using the Metrohm Autolab potentiostat. The results indicate that both materials exhibit good corrosion resistance, but there are differences in their performance under specific conditions. While lean duplex stainless steel, LDX 2101, can be used as a substitute for duplex stainless steel UNS S32205, its corrosion resistance and mechanical properties gradually decrease over time due to the reduced nickel and molybdenum content. As a result, it would not be as effective as duplex stainless steel UNS S32205 in withstanding corrosion in aggressive conditions over a prolonged period.

Effect of Powder Reuse on Powder Characteristics and Properties of DED Laser Beam Metal Additive Manufacturing Process with Stellite® 21 and UNS S32750

In this work, the influence of powder reuse up to three times on directed energy deposition (DED) with laser processing has been studied. The work was carried out on two different gas atomized powders: a cobalt-based alloy type Stellite® 21, and a super duplex stainless steel type UNS S32750. One of the main findings is the influence of oxygen content of the reused powder particles on the final quality and densification of the deposited material and the powder catch efficiency of the laser deposition process. There is a direct relationship between a higher surface oxidation of the particles and the presence of oxygen content in the particles and in the as-built materials, as well as oxides, balance of phases (in the case of the super duplex alloy), pores and defects at the micro level in the laser-deposited material, as well as a decrease in the amount of material that actually melts, reducing powder catch efficiency (more than 12% in the worst case scenario) and the initial bead geometry (height and width) that was obtained for the same process parameters when the virgin powder was used (without oxidation and with original morphology of the powder particles). This causes some melting faults, oxides and formation of undesired oxide compounds in the microstructure, and un-balance of phases particularly in the super duplex stainless steel material, reducing the amount of ferrite from 50.1% to 37.4%, affecting in turn material soundness and its mechanical properties, particularly the hardness. However, the Stellite® 21 alloy type can be reused up to three times, while the super duplex can be reused only once without any major influence of the particles’ surface oxidation on the deposited material quality and hardness.

Multimodal Characterization of AM316 Crevice Corrosion

Non-destructive 3D characterization techniques are particularly important for materials synthesized by advanced manufacturing techniques that display disparity from their namesake identifiers (e.g. UNS S31600 or SS316). This is a particular concern for non-equilibrium materials, such as additively manufactured (AM) alloys, that often contain porosity, surface roughness, phases, microstructures and internal stress not exhibited in wrought or cast counterparts. This work examines chemical, electrochemical and microstructural evolution of AM and wrought SS316 under a crevice corrosion configuration. These results include chronoamperometric signatures, potentiometric sensors to track pH and X-ray computed micro-tomography 3D reconstructions during crevice corrosion. In-situ measurements are combined with initial and post-mortem SEM and EDS to better understand two AM316 materials that exhibit ennobled and more active behavior relative to wrought SS316. Local composition and phase heterogeneity at different length scales is shown to be a primary driver for contrasting crevice corrosion performance.

A Bi-Pronged Attempt at Normalizing DL-EPRT Vis-à-Vis Grain-Boundary/σ-Phase Locales in Thermally Sensitized UNS S32205 Duplex Stainless Steel

In a quest to vet UNS S32205 as a potential structural material to serve moderate-to-high temperature operations of NPP auxiliary components, the DL-EPR test was exploited. A bifronted scheme comprised of 650 and 850 °C discrete treatments intended to explore progressive eutectoid decomposition and degree-of-sensitization (DoS) scenarios was adopted. The nuance witnessed with yet another dual approach—the Cihal- and image processing (IP)-normalized signal landscape—was rationalized through its attribution to culprit microstructures. This was sought, inter alia, in the vicinity of grain boundaries and σ-phase inclusions by virtue of postmortem FESEM, STEM-EDX, HRTEM SAED and XRD ascertainment. Discernable reactivation-kinetics resurgence was believed to mark the onset of deleterious σ-phase dissolution. This only came into fruition with longer ageing times (8–17 h) at 650 °C and succumbed to prematurely (1 h), and at DC biases more cathodic than −0.25 VAg/AgCl with the 850 °C counterpart. Opportune corroboration was offered in ir/ia breakaway for the respective conditions, which was unveiled to be particularly pre-emptive (5 h) with IP- vs. Cihal-normalized peers (8 h) related to the 650 °C condition. Meanwhile, the 850 °C condition endured a similar surge after as little as 1 h of ageing across the board, which hints at concomitant sigma-phase culpability.

Microstructural Characterization of Aged Welded Joints of a UNS S32750 Superduplex Stainless Steel

Microstructural Characterization of Aged Welded Joints of a UNS S32750 Superduplex Stainless Steel

Environmentally Assisted Cracking of Duplex and Lean Duplex Stainless Steel Reinforcements in Alkaline Medium Contaminated with Chlorides

Herein, the corrosion performance of different stainless steel (SS) reinforcing bar grades in alkaline solution is presented, including UNS S32205 duplex stainless steel (DSS), UNS S32304 and UNS S32001 lean DDS (LDSS). The electrochemical dissolution kinetics were studied by potentiodynamic polarization and the Tafel slope method. The environmentally assisted cracking (EAC) mechanisms of the different SS grades in the presence of Cl− were revealed with the slow strain rate test (SSRT). The higher activation of the anodic branch and the loss of toughness were related to the austenite-to-ferrite phase ratio. UNS S32205 DSS presented the slowest anodic dissolution kinetics, mainly due to the higher austenite content compared to the other LDSS; however, it suffered a more severe EAC than the UNS S32304 LDSS. In the case of UNS S32001 LDSS, even while having the lowest Ni content (i.e., large ferrite α-phase ratio), it experienced the least decrease in elongation as well as low anodic dissolution kinetics for Cl− contents up to 8 wt.%, where the Cl− threshold was reached.

Effect of Temperature on Passive Film Characteristics of LPBF (Laser Powder-Bed Fusion) Processing on UNS-S31603.

The effect of temperature on the localized corrosion resistance and passive film characteristics of laser powder-bed fusion (LPBF) 316L (UNS S31603) was studied in a buffered 3.5 wt% NaCl solution at 25, 50, and 75 °C. DC techniques such as cyclic potentiodynamic polarization showed lower passive current densities, high breakdown potentials, and a higher resistance to initial breakdown compared with wrought 316L samples at all temperatures. However, LPBF 316L was more susceptible to metastable pitting at potentials before film breakdown and higher damage accumulation post film breakdown. AC techniques, such as Mott-Schottky analysis and electrochemical impedance spectroscopy, showed that the formed passive film was more robust on the LPBF 316L samples at all temperatures, accounting for the higher initial resistance to pitting. However, with increasing temperatures, the film formed had an increasing concentration of defect density. Passive compositions at the various test temperatures studied using X-ray photoelectron spectroscopy (XPS) showed that the LPBF samples showed higher amounts of Cr and Fe oxides and hydroxides compared with the wrought samples, which made the passive films on the LPBF samples more compact and protective. Investigation of the pits formed on the LPBF showed the preferential regions of attack were the melt-pool boundaries and cell interiors due to their being depleted of Cr and Mo when compared with the boundaries and matrix.

Corrosion behavior of combination of laser beam welded UNS S32304 + SS304L in 3.5% NaCl solution

This study investigates the corrosion behavior of laser beam-welded UNS S32304 and SS304L in 3.5% NaCl solutions, focusing on the effects of temperature. The primary objective is to enhance the understanding of corrosion resistance in welded materials and inspire advancements in corrosion mitigation strategies. The methodology involves assessing corrosion resistance under varying temperatures and comparing the performance of laser beam welding (LBW) with that of the base metals. Scanning electron microscopy analysis reveals effective passivation, while quantitative analysis indicates differences in chloride ion coverage between the weld metal and base metals. Tafel plots and electrochemical impedance spectroscopy demonstrate enhanced corrosion potential and improved barrier properties for the weld metal. Results indicate a marginal reduction in corrosion resistance at 50 °C for both base metals. LBW metals corrosion resistance demonstrates superior performance, with only 5% reduction in breakdown potential compared to 10% in base metals. Compared to the base metal, it exhibits a substantial reduction in corrosion rate, ranging from 60 to 75%. This supports enhanced corrosion resistance and material stability. Additionally, similar results are observed after the analysis with scanning electron microscopy images, reinforcing the efficacy of LBW in improving corrosion resistance of LBW UNS S32304 and SS304L. These findings underscore the potential of LBW for applications requiring robust corrosion performance. By contributing to the understanding of the corrosion behavior of laser beam-welded materials, this study addresses a critical research gap in material science and corrosion engineering. Future research may explore long-term durability and corrosion resistance under diverse environmental conditions to further elucidate the mechanisms driving the observed differences in corrosion behavior.

Study on the Deformation Behavior of Two Phases during the Low Cycle Fatigue of UNS S32750 Duplex Stainless Steel.

In this paper, the deformation behavior of UNS S32750 (S32750) duplex stainless steel during low cycle fatigue was studied by controlling the number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The microhardness of the two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. The two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in the two phases was obviously different. With the increase in cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and a dislocation array to a sub-grain structure, while the dislocation in austenite gradually develops from dipole array to an ordered Taylor lattice network structure.

Investigating microstructure, mechanical properties, and pitting corrosion resistance of UNS S32760 super duplex stainless steel after linear friction welding

High-performance alloys such as super duplex stainless steels (SDSS) are of interest to the oil and gas industry, especially in deep and ultra-deep reservoirs where high pressures and highly corrosive environments are prevalent. SDSS have high nitrogen contents and pitting resistant equivalent number (PREN) values greater than 40, however, fusion welds of these alloys can exhibit unsuitable microstructures and defects that may result in failure during usage. Solid-state linear friction welding (LFW) offers an alternative for the effective joining of SDSS with a less detrimental effect on microstructure and properties. In this work, four LFW joints in UNS S32760 SDSS were produced and investigated by evaluating the process parameters required to achieve a high-quality joint with the desirable metallurgical, mechanical, and localized corrosion properties. These properties were assessed through metallography (optical microscopy and scanning electron microscopy), tensile and microhardness tests, and corrosion analysis according to the ASTM G48A standard. Results indicated that one specific combination of LFW parameters led to a defect-free joint, and that the mechanical properties of the weld in this case were comparable to those of the base material. Additionally, an adequate balance between ferrite and austenite phases was achieved throughout the microstructural gradients seen in the weld region. Microhardness values were below 350 HV, thus complying with the DNV–OS–F101 standard. Furthermore, no pitting corrosion was observed in this joint under the testing conditions suggested by ASTM G48A.

Influence of Solution Treatment Process on the Properties of Duplex Stainless Steels: A Comparative Study on Microstructure and Corrosion Properties of UNS S32205 and UNS S32760

The study investigated the effect of the solution treatment process on the corrosion behavior and microstructure of the duplex stainless steel. It was also aimed to reveal this effect comparatively depending on the chemical composition and alloying element content. For this purpose, UNS S32205 and UNS S32760 alloys were treated at 1000 °C, 1020 °C and 1040 °C for an hour. A solution treatment temperature was determined according to Thermo-Calc analysis. The examined samples were characterized by an optical microscope, scanning electron microscope, and XRD analysis. Also, electrochemical impedance spectroscopy and potentiodynamic polarization analyses revealed the corrosion properties of solution-treated samples. Microstructural studies showed that enhanced solution treatment temperature increased ferrite content for both alloys. A lower solution treatment temperature caused the formation of sigma in the microstructure of S32760 alloy. On the other hand, the charge transfer resistance of the passive layer was reduced after solution treatment at 1000 °C and 1020 °C, indicating decreasing corrosion resistance. A higher austenite ratio in S32205 led to pitting, while corrosion resistance improved with higher treatment temperatures. The presence of the sigma phase in S32760 significantly impacted corrosion properties by increasing ion transfer on the surface, leading to reduced corrosion resistance. It was determined that solution treatment at 1040 °C was appropriate for both alloys to achieve the desired microstructure and corrosion properties.

Numerical simulation on the laser beam welded UNS S32304 duplex steel and 304L stainless steel joints using ANSYS and response surface methodology

Numerical simulation on the laser beam welded UNS S32304 duplex steel and 304L stainless steel joints using ANSYS and response surface methodology

Optimizing Machining Efficiency in High-Speed Milling of Super Duplex Stainless Steel with SiAlON Ceramic Inserts

Super duplex stainless steels (SDSSs) are widely utilized across industries owing to their remarkable mechanical properties and corrosion resistance. However, machining SDSS presents considerable challenges, particularly at high speeds. This study investigates the machinability of SDSS grade SAF 2507 (UNS S32750) under high-speed milling conditions using SiAlON insert tools. Comprehensive analysis of key machinability indicators, including chip compression ratio, chip analysis, shear angle, tool wear, and friction conditions, reveals that lower cutting speeds optimize machining performance, reducing cutting forces and improving chip formation. Finite element analysis (FEA) corroborates the efficacy of lower speeds and moderate feed rates. Furthermore, insights into friction dynamics at the tool–chip interface are offered, alongside strategies for enhancing SDSS machining. This study revealed the critical impact of cutting speed on cutting forces, with a significant reduction in forces at cutting speeds of 950 and 1350 m/min, but a substantial increase at 1750 m/min, particularly when tool wear is severe. Furthermore, the combination of 950 and 1350 m/min cutting speeds with a 0.2 mm/tooth feed rate led to smoother chip surfaces and decreased friction coefficients, thus enhancing machining efficiency. The presence of stick–slip phenomena at 1750 m/min indicated thermoplastic instability. Optimizing machining parameters for super duplex stainless steel necessitates balancing material removal rate and surface integrity, as the latter plays an important role in ensuring long-term performance and reliability in critical applications.

Effect of Artificial Aging in the Microstructure and Corrosion Performance of Superduplex UNS S32750 Stainless Steel

Superduplex stainless steels have great mechanical and corrosion properties. However, its chemical composition makes it prone to intermetallic phase precipitation during thermal processing. Sigma (σ), chi (χ), and chromium nitrides (Cr2N) remove Cr and Mo from the matrix, reducing the corrosion and mechanical resistance. Understanding the effects of thermal processing on the secondary phase’s precipitation and depletion of the material’s performance is crucial to its applications. Thus, this work aims to analyze the behavior of the corrosion performance of the UNS S32750 after thermal treatment at 800°C, for 60, 180, 300, and 420 minutes, in comparison to the as-received material. Optical emission spectrometry, X-ray diffraction, and SEM with backscattered electrons (BSE) were used to evaluate the material. The corrosion performance was evaluated with the cyclic potentiodynamic polarization technique. The main results and conclusions obtained in the study were a decomposition of the ferrite phase into the χ and σ phases, with the formation of the χ phase being predominant in shorter times, while for longer aging times σ formed in greater quantities. It was also possible to verify a more aggressive corrosion trend for aged samples in the regions adjacent to the formation of the χ and σ phases. It was also possible to observe that the losses generated in corrosion resistance were greater for aging times longer than 60 minutes. The aging treatment significantly reduced the material’s corrosion resistance in conjunction with the formation of precipitates.

Corrosion Study on Duplex Stainless Steel UNS S31803 Subjected to Solutions Containing Chloride Ions.

In the present work, the influence of a corrosive environment and temperature on the corrosion resistance properties of duplex stainless steel S31803 was evaluated. The corrosive process was carried out using solutions of 1.5% HCl (m/m) and 6% FeCl3 (m/m), at temperatures of 25 and 50 °C. The microstructure of UNS S31803 duplex stainless steel is composed of two phases, ferrite and austenite, oriented in the rolling direction, containing a ferrite percentage of 46.2% in the rolling direction and 56.1% in the normal direction. Samples, when subjected to corrosive media and temperature, tend to decrease their mechanical property values. It was observed, in both corrosive media, that with increasing test temperature, there is an increase in the corrosion rate, both uniform and pitting. The sample in HCl solution obtained a uniform corrosion rate of 0.85% at 25 °C and 0.92% at 50 °C and pitting rates of 0.77% and 1.47% at the same temperatures, respectively. When tested in FeCl3 solution, it obtained uniform corrosion of 0.0006% and 0.93% and pitting of 0.53% and 18.5%, at the same temperatures. A reduction in dissolution potentials is also noted, thus characterizing greater corrosion in the samples with increasing temperature.

Microstructural characterization and corrosion behaviour of heat treated standard stainless steels in tar sand

This paper aims to investigate the corrosion behaviour of heat-treated standard duplex stainless steel (UNS S32205) in the recovery of bitumen from Nigerian-rich tar sand, using sodium hydroxide (NaOH) as the process solution. Appropriate material family needs to be identified for the exploitation of tar sand resources to ensure sustainable extraction of bitumen. UNS S32205 offers exceptional mechanical properties and excellent corrosion resistance which makes it a great material choice for demanding applications, including offshore platforms and construction projects. Samples of UNS 32205 were heat-treated and immersed in the digested tar sand, maintaining a process temperature of 90°C. The microstructure of the corrosion coupons was studied using SEM/EDS (Scanning Electron Microscope/Energy Dispersive Spectroscope), and the corrosion rate of the samples was derived using gravimetric technique following ASTM G31 standard. The SEM micrographs indicated varying degrees of pits associated with the passivity of UNS 32205 and an imbalance between its ferrite and austenite phases due to the presence of secondary precipitates formed during heat treatment.The normalized sample, having a corrosion rate of 0.053 mm/year, exhibited the best corrosion resistance, followed by oil quenching (0.054 mm/year), then annealing (0.076 mm/year), and water quenching (0.077 mm/year), where they all showed improved corrosion resistance over the as-received sample having a corrosion rate of 0.078 mm/year.