Unit Power Factor Research Articles

Robust direct power control of a three-phase PWM rectifier

This paper presents two robust controls techniques: current control in the dq reference frame and direct power control (DPC) applied to a three-phase PWM rectifier to achieve efficient dc voltage regulation, unit power factor control and harmonic distortion rate reduction. Simulations were performed using Matlab/Simulink software. According to these results, the DPC direct power control seems to be more efficient than the current control in the dq reference frame, which has a lower harmonic distortion rate, and the DC voltage follows its new reference for the two developed controls. However, the response time, overshoot and oscillations of the controlled quantities, as well as the exponential convergence of the errors for the transient regime and the setpoint change, are different. It can be seen that the best values of the latter are those obtained by applying the DPC direct power control, which is considered to be the best performing and most efficient control compared to the other control.

A Multi-Functional Reactive Power Compensation Device with the Capability of Grounding Fault Regulation and Its Parameter Design Method

Aiming at the problems of low equipment utilization and the high-capacity requirements of existing arc-suppression devices, a multi-functional reactive power compensation device with the capability of grounding fault regulation (MF-RPCD) is proposed. Firstly, the topology and operation mechanism of MF-RPCD are introduced in this paper. MF-RPCD works in a reactive power compensation mode when a power grid is under normal operation to ensure the unit power factor operation of the power-grid side. When a single line-to-ground fault occurs in the power grid, MF-RPCD works in a fault-regulation mode to effectively suppress the ground-fault current. Secondly, the parameters of the active and passive parts of MF-RPCD are optimally designed to ensure the stable operation of MF-RPCD. Finally, the correctness, feasibility and effectiveness of the proposed topology and functions are verified using simulations and experiments.

Integrated Control Design for Hybrid Grid-Photovoltaic Systems in Distillation Applications: A Reference Model and Fuzzy Logic Approach

This paper presents a novel hybrid structural control solution designed for distillation systems that utilize a solar source alongside an electrical grid. The power conversion architecture incorporates a reversible bridge rectifier and a quadratic boost converter. The hybrid photovoltaic grid configuration offers several benefits, including source complementarity, enhanced dependability, and energy availability aligned with power requirements. Leveraging a photovoltaic source operating at maximum power facilitates energy conservation. On the control front, an adaptive technique based on a reference model is proposed. Fuzzy logic governs the quadratic boost converter, simplifying the management of its complex nonlinear nature. The control strategy aims to maximize solar power utilization, minimize harmonic components in the grid current, synthesize an adaptive controller, and achieve a near-unit power factor on the grid. The simulation results for a steady distillation system demonstrate promising findings. Despite variations in irradiation, load power, and grid drops, the system maintains a minimal bus voltage ripple, remaining close to the intended value. Optimization of the panel-generated power leads to improved PV source utilization and enhanced system efficiency. Furthermore, the combination with an electrical grid achieves a low rate of grid current distortion and a unitary power factor.

Advanced nonlinear control of WEC system in AC microgrid connected to the main grid with electric vehicle integration

This research investigates an AC microgrid interconnected with the utility grid, comprising a 5.2 kW wind power system using a Permanent Magnet Synchronous Generator (PMSG), a 6.1 kW photovoltaic system (PVS), and integrated electric vehicles (EVs) with 600 V, 10Ah batteries operating in V2G and G2V modes. Bidirectional back-to-back converters, controlled via a voltage-oriented control (VOC) strategy, facilitate the interconnections. The PMSG system is controlled using vector control methodology, while the PVS employs a double-stage configuration with a perturb and observe algorithm for maximum power point tracking (MPPT). Advanced controllers based on Active Disturbance Rejection Control (ADRC) regulate generator speed and the DC link voltage of the grid-connected converters. The backstepping technique is utilized for internal loop control of PMSG currents and coupling filter currents for the grid-connected converters. A comparative study between the ADRC-Backstepping controller and the PI controller was conducted, demonstrating the superior efficacy of the ADRC-Backstepping approach. Simulation results show accurate regulation of DC link voltage at reference levels, operation with unit power factor, with a current THD below 4 %, demonstrating the effectiveness and robustness of the proposed control strategies under varying conditions.

Research on Control Strategy of PMSG-PWM Power Generation System with Tidal Energy

Aiming at the characteristics of machine-side output instability and the wide-range variation in the tidal energy PMSG-PWM power generation system, we propose a control scheme with a high anti-interference capability applied to the PWM rectifier. The outer voltage loop adopts sliding mode control (SMC) with the variable exponential convergence law based on expanded state observer (ESO). By compensating the perturbation observation value into the sliding mode controller in advance, it improves the robustness and response speed of the system and suppresses the direct current (DC)-side voltage jitter phenomenon. The current inner loop combines model prediction (MP) with direct power control (DPC). By introducing time-delay compensation, it improves the control accuracy, reduces the machine-side harmonic content, and enables the system to maintain unit power factor operation despite external disturbances. Simulation and experiment results show that, under the wide range of PMSG output, the PMSG-PWM power generation system adopting the “ESO_SMC+MDPDC” scheme has a fast dynamic regulation of DC output voltage, obvious vibration suppression effect, low harmonic content of the current on the PMSG side, and fast current tracking speed, which verify the feasibility of applying this system to the field of tidal energy generation.

Predictive power control strategy without grid voltage sensors of the Vienna rectifier

AbstractThis paper proposes a predictive power control strategy for the three‐phase, six‐switch Vienna rectifier without grid voltage sensors to reduce the hardware cost and complexity of a high‐power PWM rectifier system. Firstly, an algorithm for calculating the AC‐side voltage in the αβ coordinate system is derived according to the operating principle of the Vienna rectifier, and a voltage observer is constructed by combining a second‐order low‐pass filter to estimate the grid voltage. Secondly, a soft start method is designed to solve the problem that the rectifier is prone to inrush current when it is started. Furthermore, the control method of grid voltage sensorless is combined with predictive power control with good dynamic characteristics and simple parameter settings to form the control strategy proposed in this paper. Finally, simulation analysis and experimental verification are carried out on the proposed control strategy. Simulation and experimental results show that the grid voltage estimation has high accuracy, a good surge current suppression effect, unit power factor operation, low input current harmonic content, and good dynamic and steady‐state performance. Therefore, the correctness and effectiveness of the strategy proposed in this paper are verified.

An SDP relaxation in the complex domain for the efficient coordination of BESS and DGs in single-phase distribution grids while considering reactive power capabilities

This research proposes an efficient energy management system design for medium-voltage distribution networks from a perspective of convex optimization. The exact nonlinear programming problem that represents the operation of distributed energy resources (DERs), such as batteries and photovoltaic sources, is approximated as an equivalent semi-definite programming (SDP) problem. This SDP approximation is achieved in the complex domain using Hermitian matrices, which are the equivalent of positive semi-definite matrices in the real number domain. Two test feeders, one with 27 nodes and the other with 33 nodes, are modified to match the characteristics of Colombian rural and urban networks. The 27-bus grid is adapted to accommodate the average demand and solar generation conditions of the municipality of Capurganá, while those of the city of Medellín are used for the 33-bus grid. One of the main contributions of this research is that it considers a DER operation with variable power factors, which allows for significant improvements compared to the traditional use of a unitary power factor scheme. Numerical comparisons are conducted using metaheuristic optimizers, including parallel versions of the particle swarm optimizer, the vortex search algorithm, and the continuous version of the genetic algorithm. These comparisons demonstrate the effectiveness of the proposed SDP approximation. All simulations are carried out in the MATLAB software (version 2022b), using the disciplined convex optimizer (CVX) and the SDPT3 and SEDUMI solvers.

Design and Implementation of Robust H∞ Control for Improving Disturbance Rejection of Grid-Connected Three-Phase PWM Rectifiers

In response to the high performance requirements of pulse width modulation (PWM) converters in grid-connected power systems, H-Infinity (H∞) control has attracted significant research interest due to its robustness against parameter variations and external disturbances. In this work, an advanced robust H∞ control is proposed for a grid-connected three-phase PWM rectifier. A two-level control strategy is adopted, where cascaded H∞ controllers are designed to simultaneously regulate the DC bus voltage and input currents even under load disturbances and non-ideal grid conditions. As a result, unit power factor, stable DC bus voltage, and sinusoidal input currents with lower harmonics can be accurately achieved. The design methodology and stability of the proposed controller are verified through a comprehensive analysis. Simulation tests and experimental implementation on a dSPACE 1103 board demonstrate that the proposed control scheme can effectively enhance disturbance rejection performance under various operating conditions.

Non-linear control for enhanced solar power under partial shading and AC load variations

This paper solves the control problem to track the maximum power in grid-connected PV systems to catch up with the changes and meet the energy demand, given the irregular and arbitrary nature of the solar source. Our work addresses the following objectives: i) extracting the maximum available power under partial shading, ii) and having a unit power factor. To achieve the above objectives, we have integrated two control components. The first one is dedicated to the extraction of the maximum power point (MPPT) particle swarming algorithm (PSO) with a backstepping controller, by shaking on the DC/DC converter duty cycle to increase the robustness and stability of the system. The backstepping control of the three-phase voltage source inverter is the second part. To verify the effectiveness of the introduced system, modelling and simulation are verified in MATLAB/Simulink.

A Programmable Source Based on Multi-level Buck EIE inverter connected to a power factor correction stage composed by a single-phase hybrid rectifier

This paper presents a power factor correction stage connected to a programmable source based on the Buck EIE converter Topology. The strategy used to ensure the unitary power factor is based on the use of the single-phase hybrid rectifier, which has the purpose of providing voltages at their outputs for the correct supply of the two cells that make up the Buck EIE converter. It was developed the computational simulation model, including the calculations of the passive elements and the control strategy applied to trigger the electronic switches.

Control with floating- and fixed-point DSPs of a low-cost Flexible Platform for a Photovoltaic Grid-Connected System working as an agent in a Distributed Generation Structure

In this paper, a low-cost flexible platform for photovoltaics is developed with a DSP-microcontroller arrangement for doing industrial control in an easy way, and the communication process between them is carried out with the McBSP bus. The control of the DC/DC boost converter and the d-q control approach of the 3-phase Voltage Source Inverter (VSI) have been established: the mathematical model of the plant is described and a decoupled control of the instantaneous active and reactive powers fed to the utility grid is achieved, allowing unitary power factor operation. Several measurements of the involved variables in the platform are described in order to evaluate the performance of the exerted control algorithms with the DSP-microcontroller arrangement, and the development of future complex algorithms and high computational tasks is validated.

Robust Voltage Vector-Controlled Three-Phase SAPF-based BPMVF and SVM for Power Quality Improvement

The multiplication of nonlinear loads leads to significant degradation of the energy quality, thus the interconnection network is subject to being polluted by the generation of harmonic components and reactive power, which causes a weakening efficiency, especially for the power factor. In three-phase systems, they can cause imbalances by causing excessive currents at the neutral. This research treats the operation of robust voltage-oriented control (VOC) for a shunt active power filter (SAPF). The main benefit of this technique is to guarantee a decoupled control of the active and reactive input currents, as well as the input reference voltage. To sustain the DC voltage, a robust PI-structure-based antiwindup is inserted to ensure active power control. Besides, a robust phase-locked loop (PLL)-based bandpass multivariable filter (BPMVF) is used to improve the network voltage quality. Furthermore, a space vector modulation (SVM) is designed to replace the conventional one. A sinusoidal network current and unitary power factor are achieved with fewer harmonics. The harmonics have been reduced from 27.98% to 1.55% which respects the IEEE 519-1992 standard. Expanded simulation results obtained from the transient and steady-state have demonstrated the high performance of the suggested control scheme.

Robust PQ-Controlled 3-Phase SAPF-based PI Anti-windup and BPMVF

This research concerns the study of a shunt active power filter intended to compensate for the harmonic currents generated by nonlinear loads. These injected harmonics significantly degrade the power factor. The PQ theory is the central point of this study. A robust phase-locked loop-based bandpass multivariable filter is developed to enhance the grid voltage. To sustain the DC-bus voltage, a PI anti-windup is placed to guarantee active power regulation. The essential purpose of this solution is to ensure a sinusoidal current with fewer harmonics and a unitary power factor. The efficiency of the proposed solution has been confirmed by the obtained results in transient and steady-state.

A robust PQ-controlled three-phase SAPF-based SVM and PI anti-windup for power quality improvement

The use of power electronics devices in electrical energy conversion installations has significantly contributed to improving the performance and efficiency of these systems. On the other hand, static converters have contributed to the deterioration of the quality of current and voltage in distribution networks. These converters consume non-sinusoidal currents, and they behave like harmonic current generators. The power factor and overall system efficiency are weakened by these injected harmonics, reactive power, and other issues. Meanwhile, those loads’ harmonic difficulties must be resolved. The research presented in this paper particularly concerns the study of a shunt active power filter (SAPF) intended to compensate for the harmonic currents generated by nonlinear loads and the compensation of reactive energy. The theory of PQ control is the subject of this research. A robust structure is proposed for that purpose. To sustain the DC-link voltage at the desired interval, a robust PI-regulator-based antiwindup is inserted to ensure active power control. Besides, space vector modulation (SVM) is designed to replace classical pulse width modulation (PWM). The principal benefits of this technique are that it supplies a unitary power factor and sinusoidal network current with no requirement for a PWM generator and fewer harmonics. A comparison between the conventional and the proposed control is established to demonstrate the superiority of the PQ-SVM scheme. The comparison mainly concerns the bus voltage as it is the responsible for the whole system stability Expanded simulation results obtained from the transient and steady-state have demonstrated high performance and have confirmed the robustness and effectiveness of the suggested method.

A Design and Implementation of a New Control Based on Petri Nets for Three Phase PWM-Rectifier

This article introduces a novel and effective diagram based on direct instantaneous power control (DPC) of a PWM-controlled rectifier connected to the grid without a switching table. An optimum control vector of the PWM rectifier's input voltage, which depends on the switching states determined by a Petri nets controller, is adopted. This approach limits the instantaneous detection errors of reactive and active powers, maintains the DC bus voltage at a reference level, and ensures current close to a sinusoidal wave, guaranteeing operation at a unit power factor. The instantaneous tracking errors of active and reactive powers and the angular position of the voltage are used as input variables for the proposed controller, which then selects the best control vector for the converter based on the transition of a Petri net. The significant advantages of DPC based on Petri nets compared to traditional switching tables are that hysteresis comparators are not required, and the classical regulation of active and reactive powers is achieved in all sectors. Simulation and testing findings demonstrated excellent performance, supporting the viability of the suggested control approach using Petri nets.

Power Quality Improvement using a New DPC Switching Table for a Three-Phase SAPF

This research focuses on the analysis and design of robust direct power control (DPC) for a shunt active power filter (SAPF). The study proposes a novel switching table design based on an analysis of the impact of inverter switching vectors on the derivatives of instantaneous reactive and active powers. The goal is to reduce the number of commutations by eliminating null vectors while maintaining the desired DC-bus voltage using a PI regulator-based anti windup technique. Additionally, a robust PLL structure-based band pass multivariate filter (BPMVF) is utilized to enhance the network voltage. The research demonstrates the effectiveness of the suggested power control through extensive simulation results, showing high performance in both transient and steady-state conditions. The proposed approach offers the advantages of sinusoidal network current, and unitary power factor, and eliminates the need for current regulators and coordinate transformations or PWM generators. Further research directions could explore the practical implementation and real-world performance of this technique in power systems.

An Advanced Switched-Capacitor Multilevel Inverter Topology With a Robust PWM Controlling Technique and Voltage Boosting Property for the Grid-Connected Renewable Energy Applications

This paper proposes an improved switched-capacitor Multilevel Inverter that utilizes fewer components. The switched capacitors are employed with the DC sources in the proposed configuration to minimize the number of DC-Links in the structure, which keeps the structure compact and combinable. Those capacitors enjoy a self-charging susceptibility with the ability to balance naturally. The suggested structure supports the expansion process to catch up with satisfactory output power levels based on a slight increase in the components count. The targeted application for this inverter involves a renewable energy system (RES) to exploit the extracted electrical power and inject it into the grid. The paper suggests a developed PWM controller to control the system’s operation. The controlling scheme has the ability to adjust the balance in the DC-Links voltages to keep generating a regular output voltage. Furthermore, it helps in extracting the maximum available power from renewable resources. Meanwhile, the controller injects the real power component into the grid, which guarantees the unit power factor operation and enhances the grid’s performance. The simulation results for both sides of RES are carried out in MATLAB/Simulink, and these results are verified experimentally through the dSPACE-1103 hardware.

An unprecedented control of 3‐phase grid tied solar photovoltaic‐hydrogen/bromine‐supercapacitor composite storage microgrid for pulse power load regulation under nonideal grid conditions

AbstractPhotovoltaic (PV) power penetration into the distribution grid has increased. PV power fluctuations, abrupt load changes, nonlinear loading, growing usage of portable electronic devices, electric cars low average power and comparatively high pulse power needs, and other factors translate into severe grid instability. As a result, in these circumstances, power exchange between PV and the utility grid becomes a difficult task. Therefore, this article proposes a hydrogen/bromine (H2/Br2) redox flow battery and supercapacitor composite energy storage for a three phase grid tied PV system with multifunctional active power filter support to ensure grid codes. Further, the system is equipped with an unprecedented control technique that encompasses: an adaptive frequency tuned complex coefficient filter‐phase locked loop that provides grid frequency and phase angle information under adverse grid conditions, a modified sparrow search algorithm tuned tilt integral derivative with filter plus double integral controllers are employed to regulate the control errors under various system dynamic and disturbance conditions, fractional order incremental conductance maximum power point tracking is incorporated to efficiently track the PV peak power irrespective of atmospheric variations, a holistic fast‐acting power based energy management control employed for efficient regulation of load power and smooth out the PV power variation, and PV feedforward control dynamics to enhances system dynamics by reducing oscillations under various atmospheric conditions. The aim is to attain a smooth power transition with the grid at the unit power factor under normal and nonideal grid conditions. With reactive power injection, the control also maintains the voltage profile. During all these operations, no trade‐off occurs with the system power quality. Matlab simulations and the real time simulation test bench results under unfavorable grid circumstances demonstrate the effectiveness of the proposed method, and system harmonics are well within bounds in all the scenarios undertaken.

High-Efficiency Interleaved Totem-Pole PFC Converter With Voltage Follower Characteristics

High power density, efficiency, control simplification, and robustness are highly demanded for power factor correction (PFC) converters. This paper proposes a totem-pole rectifier based on the switching cell with switching frequency modulation (SC-SFM). The SC-SFM features interleaved operation, soft commutation, and resistive characteristics with continuous conduction in the input inductor. The converter operates without needing sensors and a control loop for the current. Unlike conventional solutions or some sensorless converters, the converter does not require a fast control loop to shape the current since the current naturally follows the input voltage. Only one output voltage sensor and one input half-line cycle detector are required to achieve unitary power factor and regulated DC output voltage. A detailed analysis of the converter operation, including the operating principle, mathematical analysis, a small signal model, and control method, is presented, including the differences in operation from the conventional PFC rectifier with the diode bridge. Experimental results evaluate a 1-kW prototype with different switch technologies (IGBT, SiC, and GaN).

Robust adaptive nonlinear control of plugin hybrid electric vehicles for vehicle to grid and grid to vehicle power flow with hybrid energy storage system

Plugin hybrid electric vehicles (PHEVs) can solve the concerns of toxic gases emissions from fossil fuel. The PHEV under consideration consists of an on-board smart charger and a hybrid energy storage system (HESS) composed of the battery as a primary power source and an ultracapacitor (UC) as a secondary power source conjoined with two DC–DC bidirectional buck-boost converters. The on-board charging unit comprises of an AC–DC boost rectifier and DC–DC buck converter. The entire system’s state model has been derived. An adaptive supertwisting sliding mode controller (AST-SMC) has been proposed for the unitary power factor correction at the grid side, tight voltage regulation of the charger and the DC bus, adaptation of time varying parameters and tracking of the currents involving the variation in the load profile. A genetic algorithm has been applied for optimizing the cost function of the controller gains. Key results refers reduction of chattering, adaptation of parametric variations, nonlinearities and external disturbances of the dynamical system. HESS results presents negligible convergence time and overshoots/undershoots even at the transients, and no steady state error. For the driving mode, the switching between dynamic and static behaviors and for parking mode, vehicle to grid (V2G) and grid to vehicle (G2V) operations have been proposed. In order to make nonlinear controller intelligent to achieve the V2G and G2V functionality, a state of charge based high-level controller has also been proposed. A standard Lyapunov stability criteria has been used to ensure asymptotic stability of the entire system. The proposed controller has been compared with sliding mode control (SMC) and finite time synergetic control (FTSC) by the simulation results using MATLAB/Simulink. Also, the hardware in loop setup has been used to validate the performance in real-time.