Ultrasonic Apparatus Research Articles

A pulse-echo measurement setup to determine viscoelastic material parameters

Abstract Due to their versatility, the application of polymers in research and industry continues to increase. Since the majority of design processes are simulation-aided, precise material parameters are required to obtain realistic results. The quasi-statically and destructively measured material parameters provided by manufacturers for this purpose are usually insufficient. An acoustic method is generally capable of measuring the frequency-dependent viscoelastic material parameters in a non-destructive manner. In particular, an ultrasonic transmission measurement setup for determining these parameters has already been presented in previous publications. However, this approach has several drawbacks, including a low sensitivity to shear parameters. To increase the sensitivity to shear parameters, a measurement setup using a pulse-echo method with a corresponding inverse approach is presented to obtain viscoelastic material parameters of polymers. A brief comparison is made between the transmission and pulse-echo methods.

AI-Based Prediction of Ultrasonic Vibration-Assisted Milling Performance.

The current study aims to evaluate the performance of the ultrasonic vibration-assisted milling (USVAM) process when machining two different materials with high deviations in mechanical properties, specifically 7075 aluminium alloy and Ti-6Al-4V titanium alloy. Additionally, this study seeks to develop an AI-based model to predict the process performance based on experimental data for the different workpiece characteristics. In this regard, an ultrasonic vibratory setup was designed to provide vibration oscillations at 28 kHz frequency and 8 µm amplitude in the cutting feed direction for the two characterised materials of 7075 aluminium alloy (150 BHN) and Ti-6Al-4V titanium alloy (350 BHN) workpieces. A series of slotting experiments were conducted using both conventional milling (CM) and USVAM techniques. The axial cutting force and machined slot surface roughness were evaluated for each method. Subsequently, Support Vector Regression (SVR) and artificial neural network (ANN) models were built, tested and compared. AI-based models were developed to analyse the experimental results and predict the process performance for both workpieces. The experiments demonstrated a significant reduction in cutting force by up to 30% and an improvement in surface roughness by approximately four times when using USVAM compared to CM for both materials. Validated by the experimental findings, the ANN model accurately and better predicted the performance metrics with RMSE = 0.11 µm and 0.12 N for Al surface roughness and cutting force. Regarding Ti, surface roughness and cutting force were predicted with RMSE of 0.12 µm and 0.14 N, respectively. The results indicate that USVAM significantly enhances milling performance in terms of a reduced cutting force and improved surface roughness for both 7075 aluminium alloy and Ti-6Al-4V titanium alloy. The ANN model proved to be an effective tool for predicting the outcomes of the USVAM process, offering valuable insights for optimising milling operations across different materials.

Ultrasound-driven piezoelectret-based nanogenerator stimulates vagus nerve for myocardial infarction treatment

Myocardial infarction (MI) stands as the predominant cause of morbidity and mortality within the spectrum of cardiovascular diseases, with an unfavorable long-term prognosis. Vagus nerve stimulation (VNS) emerges as a potential clinically significant intervention for alleviating myocardial remodeling after MI, offering promise as a therapeutic approach. However, challenges persist in addressing the fundamental issues of flexibility, miniaturization, and the long-term use of VNS devices. Here, we devised an implantable ultrasound-driven piezoelectret-based nanogenerator (UPN) as a wireless-powered and battery-free vagus nerve stimulator. The UPN with the features of flexibility and lightweight exhibited a maximum output of 10.68 V and 261 μA (peak to peak) under an ultrasonic probe setup at 700 mW cm−2. In the in vivo efficacy study, VNS therapy resulted in a notable improvement in cardiac function with the treatment of UPN, a 20.42 % enhancement in left ventricular ejection fraction and an 11.76 % increase in fractional shortening on the 28th day were realized. Concomitantly, inflammatory responses, myocardial fibrosis, and sympathetic nerve remodeling witnessed a significant reduction. Particularly noteworthy is the observed therapeutic effect linked to the inhibition of the IL-17 and TNF signaling pathways. In summary, this study introduces a novel strategy for nerve stimulation, offering a potential avenue for treating chronic inflammatory diseases.

Ultrasonic reactor set-ups and applications: A review

Sonochemistry contributes to green science as it uses less hazardous solvents and methods to carry out a reaction. In this review, different reactor designs are discussed in detail providing the necessary knowledge for implementing various processes. The main characteristics of ultrasonic batch systems are their low cost and enhanced mixing; however, they still have immense drawbacks such as their scalability. Continuous flow reactors offer enhanced production yields as the limited cognition which governs the design of these sonoreactors, renders them unusable in industry. In addition, microstructured sonoreactors show improved heat and mass transfer phenomena due to their small size but suffer though from clogging. The optimisation of various conditions of regulations, such as temperature, frequency of ultrasound, intensity of irradiation, sonication time, pressure amplitude and reactor design, it is also discussed to maximise the production rates and yields of reactions taking place in sonoreactors. The optimisation of operating parameters and the selection of the reactor system must be considered to each application’s requirements. A plethora of different applications that ultrasound waves can be implemented are in the biochemical and petrochemical engineering, the chemical synthesis of materials, the crystallisation of organic and inorganic substances, the wastewater treatment, the extraction processes and in medicine. Sonochemistry must overcome challenges that consider the scalability of processes and its embodiment into commercial applications, through extensive studies for understanding the designs and the development of computational tools to implement timesaving and efficient theoretical studies.

Experimental investigation of micro-machining of borosilicate glass using an ultrasonic assisted rotary electrochemical discharge machining (UA-RECDM) process

Electrochemical discharge machining is an advanced micro-machining process for machining of conductive as well as non-conductive hard and brittle materials, e.g. glass, ceramics, silicon wafer, etc. The present work explores the machining of glass using an in-house developed novel ultrasonic assisted rotary electrochemical discharge machining setup. The setup has specialized features, such as using ultrasonic vibrations to tool the electrode and incorporating rotary motion for manipulating the workpiece. Experiments were conducted using a one factor at a time approach by varying the tool feed rate, the amplitude of the vibrations and the rotation of the workpiece as process parameters. The quality of the machining output was evaluated by observing two key parameters: the overcut and the circularity of the hole. It was observed that as the workpiece rotation speed increased from 40 rpm to 60 rpm, the overcut in the machined samples decreased from 181.378 μm to 163.564 μm. The rotary motion of the workpiece caused a seeping action of the electrolyte in the hydrodynamic regime, leading to the formation of a thin gas film and the stabilization of the discharging process. The morphology of the machined hole exhibits better circularity, low heat-affected zones, minimum micro-cracks and smooth edges at its periphery due to stable discharge formation.

Quantitative ultrasonic characterization of Ti-6Al-4V components with surface roughness

Ultrasonic immersion testing enables nondestructive characterization of material microstructure through quantitative linkages between wave propagation parameters and features of interest. However, accurate measurements of metrics such as wave speed and attenuation generally require smooth test samples to ensure the reflected wave packets are not distorted. Thus, rough surfaces are mechanically polished before ultrasonic testing, which compromises the nondestructive nature of the measurement, distorting the sample geometry and imparting local damage. This challenge is particularly salient with the advent of manufacturing processes, such as metal additive manufacturing, that result in rough samples that must be characterized for heterogeneities in their as-manufactured state. This work examines the influence of surface roughness on longitudinal wave speed and attenuation in wrought and additively manufactured Ti-6Al-4V specimens. Samples are measured in an ultrasonic immersion setup before and after mechanical polishing using varying transducer frequencies and focal profiles. The resulting data informs the error generated in ultrasonic measurements as a function of roughness parameters, thereby informing the sample preparation needed for desired precision levels. Lastly, new measurement protocols are explored to correct for the presence of surface irregularities in a point-by-point fashion. This work was supported by the Robert W. Young Award for Undergraduate Student Research.

Assessment of sulphur content in nitrile rubber through ultrasonic measurement

ABSTRACT Ultrasonic testing is a popular non-destructive method for characterising engineering materials and detecting their properties. Diverse quantities of sulphur are incorporated into an uncured rubber compound, which is subsequently cured under specific pressure and heat conditions to attain the desired properties in the final product. The present work represents a quantitative estimation of sulphur content for cured NBR (Nitrile Butadiene Rubber) samples by an ultrasonic approach. The experiments have been conducted using cured NBR samples with varying sulphur content, ranging from 0% to 1.34%. Ultrasonic pulse behaviour at different temperatures (30°C to 160°C) has been observed using an ultrasonic setup which has been developed in-house. A-scan data is obtained at a sampling rate of 80 MHz using an 18 mm diameter broadband transducer with a 1 MHz central frequency. The ultrasonic longitudinal velocity (ULV) of rubber is determined from A-scan data using time-of-flight, and sulphur content has a significant impact on the ULV. At a temperature of 160°C, the ultrasonic longitudinal velocity (ULV) is measured at 1262 m/s for a sample with 0.62% sulphur content, and at 1321 m/s for a sample with 1.34% sulphur content.

Assessment of sulfur content in nitrile rubber through ultrasonic measurement

ABSTRACT Ultrasonic testing is a popular non-destructive method for characterising engineering materials and detecting their properties. Diverse quantities of sulphur are incorporated into an uncured rubber compound, which is subsequently cured under specific pressure and heat conditions to attain the desired properties in the final product. The present work represents a quantitative estimation of sulphur content for cured NBR (Nitrile Butadiene Rubber) samples by an ultrasonic approach. The experiments have been conducted using cured NBR samples with varying sulphur content, ranging from 0% to 1.34%. Ultrasonic pulse behaviour at different temperatures (30°C to 160°C) has been observed using an ultrasonic setup which has been developed in-house. A-scan data is obtained at a sampling rate of 80 MHz using an 18 mm diameter broadband transducer with a 1 MHz central frequency. The ultrasonic longitudinal velocity (ULV) of rubber is determined from A-scan data using time-of-flight, and sulphur content has a significant impact on the ULV. At a temperature of 160°C, the ultrasonic longitudinal velocity (ULV) is measured at 1262 m/s for a sample with 0.62% sulphur content, and at 1321 m/s for a sample with 1.34% sulphur content.

Protective effect of naringin against radiation-induced heart disease in rats via Sirt1/NF-κB signaling pathway and endoplasmic reticulum stress.

This study was designed to explore the protective effect and mechanism of naringin (NG) on radiation-induced heart disease (RIHD) in rats. Rats were divided into four x-ray (XR) irradiation groups with different absorbed doses (0/10/15/20 Gy), or into three groups (control, XR, and XR + NG groups). Subsequently, the ultrasonic diagnostic apparatus was adopted to assess and compare the left ventricular ejection fraction (LVEF), left ventricular fractional shortening (LVFS), left ventricular internal diameter at end diastole (LVIDd), and left ventricular internal diameter at end systole (LVIDs) in rats. Hematoxylin-eosin (H&E) staining and Masson staining were applied to detect the pathological damage and fibrosis of heart tissue. Western blot was used to measure the expression levels of myocardial fibrosis-related proteins, endoplasmic reticulum stress-related proteins, and Sirt1 (silent information regulator 1)/NF-κB (nuclear factor kappa-B) signaling pathway-related proteins in cardiac tissues. Additionally, enzyme-linked immunosorbent assay was utilized to detect the activities of pro-inflammatory cytokines, malondialdehyde (MDA), superoxide dismutase (SOD), and catalase (CAT) in cardiac tissue. The results showed that NG treatment significantly attenuated the 20 Gy XR-induced decline of LVEF and LVFS and the elevation of LVIDs. Cardiac tissue damage and fibrosis caused by 20 Gy XR were significant improved after NG treatment. Meanwhile, in rats irradiated by XR, marked downregulation was identified in the expressions of fibrosis-related proteins (Col I, collagen type I; α-SMA, α-smooth muscle actin; and TGF-β1, transforming growth factor-beta 1) and endoplasmic reticulum stress-related proteins (GRP78, glucose regulatory protein 78; CHOP, C/EBP homologous protein; ATF6, activating transcription factor 6; and caspase 12) after NG treatment. Moreover, NG treatment also inhibited the production of pro-inflammatory cytokines [interleukin-6, interleukin-1β, and monocyte chemoattractant protein-1 (MCP-1)], reduced the expression of MDA, and promoted the activities of SOD and CAT. Also, NG treatment promoted Sirt1 expression and inhibited p65 phosphorylation. Collectively, XR irradiation induced cardiac injury in rats in a dose-dependent manner. NG could improve the cardiac injury induced by XR irradiation by inhibiting endoplasmic reticulum stress and activating Sirt1/NF-κB signaling pathway.

Novel Nanoprobe with Combined Ultrasonography/Chemical Exchange Saturation Transfer Magnetic Resonance Imaging for Precise Diagnosis of Tumors.

Given that cancer mortality is usually due to a late diagnosis, early detection is crucial to improve the patient's results and prevent cancer-related death. Imaging technology based on novel nanomaterials has attracted much attention for early-stage cancer diagnosis. In this study, a new block copolymer, poly(ethylene glycol)-poly(l-lactide) diblock copolymer (PEG-PLLA), was synthesized by the ring-opening polymerization method and thoroughly characterized using Fourier transform infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy (H-NMR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The obtained PEG-PLLA was used to prepare nanoparticles encapsulated with perfluoropentane and salicylic acid by the emulsion-solvent evaporation method, resulting in a new dual-mode nano-image probe (PEG-PLLA@SA·PFP). The zeta potential and mean diameter of the obtained nanoparticles were measured using dynamic light scattering (DLS) with a Malvern Zetersizer Nano. The in vitro biocompatibility of the PEG-PLLA nanoparticles was evaluated with cell migration, hemolysis, and cytotoxicity assays. Ultrasonic imaging was performed using an ultrasonic imaging apparatus, and chemical exchange saturation transfer (CEST) MRI was conducted on a 7.0 T animal scanner. The results of IR and NMR confirmed that the PEG-PLLA was successfully synthesized. The particle size and negative charge of the nanoparticles were 223.8 ± 2.5 nm and -39.6 ± 1.9 mV, respectively. The polydispersity of the diameter was 0.153 ± 0.020. These nanoparticles possessed good stability at 4 °C for about one month. The results of cytotoxicity, cell migration, and hemolysis assays showed that the carrier material was biocompatible. Finally, PEG-PLLA nanoparticles were able to significantly enhance the imaging effect of tumors by the irradiation of ultrasound and saturation by a radiofrequency pulse, respectively. In conclusion, these nanoparticles exhibit promising dual-mode capabilities for US/CEST MR imaging.

Clinical Application of Ultrasound Elastic Imaging in Assessing Poststroke Complex Regional Pain Syndrome (CRPS).

This study aimed to explore the characteristics and clinical application of ultrasonic elastography in peripheral soft tissue in patients with poststroke complex regional pain syndrome (CRPS). Complex regional pain syndrome (CRPS) type I is also known as shoulder hand syndrome (SHS). Its main symptoms include shoulder pain, limited activity, upper arm, wrist, and knuckle joint pain. Ultrasonic elastic imaging technology is gradually being applied to musculoskeletal system evaluation, primarily for the elastic examination of superficial tissue, as a result of the continual advancements in ultrasound technology. To make up for the absence of conventional imaging, functional state evaluation of the motor system can offer conventional ultrasonic tissue elasticity and hardness data. The purpose of this study was to objectively quantify the soft tissue surrounding the shoulder joint of stroke patients with CRPS using ultrasonic elastic imaging and to determine the diagnostic usefulness of ultrasonic elastic imaging for CRPS in stroke in order to promote its usage in clinical practice. Patients diagnosed with CRPS following a stroke and admitted to the rehabilitation unit at Shanxi Bethune Hospital between January, 2021 to June, 2021 were included in the analysis. The control group consisted of people without pain in their shoulder joints. Each group consisted of 30 patients. A high-frequency wire array probe (frequency = 8-16 Hz) was employed in conjunction with an ultrasonic diagnostic apparatus. A quantitative analytic system determined Young's modulus of the tissue, while the tracking of the shear wave provided an elastin map in real-time. An excitation pulse of acoustic radiation force was used to cause shear waves in the tissue. The Young's modulus of supraspinatus muscle in the study and control groups was 289.16±22.07 Kpa and 231.99±23.61 Kpa, respectively (P <0.01). Young's modulus values of the study group's subscapular biceps were compared to those of the control group (P > 0.05). The supraspinatus shear wave elastographic (SWE) imaging value was 10.01±0.49 m/s in the study group and 7.92±0.50 in the control group (P <0.05). The study and control groups had subscapular muscle SWE values of 15.99±1.95 and 8.64±0.56 m/s, respectively (P <0.05). The average biceps tendon SWE value in the study and control groups was 6.39±0.42 and 4.69±0.36 m/s, respectively (P <0.05). In conclusion, the SWE assessed by ultrasound elastography is useful for early diagnosis and evaluation of the superior shoulder tendon, subscapular tendon, and biceps tendon of CRPS following stroke.

Heat-tonifying acupuncture relieves pain and synovial inflammatory injury by regulating Keap1-Nrf2/ARE/ HO-1 signaling pathway in rabbits with cold syndrome type rheumatoid arthritis

To observe the effect of heat-tonifying needling on Keap1-Nrf2/ARE/HO-1 signal transduction pathway in knee synovium in rabbits with cold syndrome type rheumatoid arthritis (RA), so as to explore its mechanisms underl-ying improvement of RA. New Zealand rabbits were randomly divided into normal control, RA model, uniform reinforcing-reducing acupuncture, twisting reinforcing acupuncture and heat-tonifying acupuncture groups, with 6 rabbits in each group. The cold syndrome type RA model was established by subcutaneous injection of mixture fluid of ovalbumin and Freund's complete adjuvant at the shoulder-back as well as injection of mixture of ovalbumin and normal saline into knee-joint cavity combined with ice-compress freezing. Acupuncture stimulation (uniform reinforcing-reducing, or twisting reinforcing or heat-tonifying) was applied to bilateral "Zusanli"(ST36) for 1 min with the needle retained for 30 min, once a day for 7 consecutive days. The general conditions of rabbits in each group were recorded, the thermal pain threshold (TPT) and perimeter of knee joints was measured. Conditions of the synovium in the knee cavity, hydrops, blood flow signal, articular surface, and related muscles were observed by using a color Doppler ultrasonic diagnostic apparatus, and the blood flow signals inside the synovium (image scores) were divided into 0 (no signals), I (1 or 2 dot-like signal), II (less than half) ad III (more than half). After H.E. staining, the pathological changes (0-3 points) were assessed according to the state of inflammatory cell infiltration, and hyperplasia of synovial matrix and coating cells. The expression levels of Keap1, Nrf2, HO-1 and GSH-PX1 mRNAs in the knee synovium were detected by quantitative real-time PCR, and the expression of knee synovial HO-1 protein was measured by Western blot. In comparison with the normal control group, the model group had a significant increase in the perimeter, pathological score, expression of Nrf2, HO-1 mRNAs and HO-1 protein (P<0.05), and an obvious decrease in the TPT, expression levels of Keap1 and GSH-PX1 mRNAs (P<0.05). Relevant to the model group, all the three acupuncture maneuvers reversed modeling-induced increase of perimeter and pathological score (P<0.05), decrease of TPT and expression of GSH-PX1 mRNA(P<0.05), further down-regulated expression of Keap1 mRNA (P<0.05), further up-regulated the expression of Nrf2, HO-1 mRNAs and HO-1 protein (P<0.05). The heat-reinforcing manipulation was significantly superior to uniform reinforcing-reducing and twirling reinforcing manipulations in up-regulating TPT, and expression of Nrf2 mRNA, GSH-PX1 mRNA, HO-1 mRNA and protein (P<0.05), and in down-regulating pathological score and Keap1 mRNA expression (P<0.05). Heat-tonifying, uniform reinforcing-reducing and twirling reinforcing needling manipulations may relieve pain and improve pathological state in RA rabbits, which may be associated with their functions in raising the ability of anti-oxidative stress by regulating Keap1-Nrf2/ARE/ HO-1 signaling pathway, the therapeutic effect of heat-tonifying needling is superior to that of uniform reinforcing-reducing and twirling reinforcing needling.

Application of Acoustic Metamaterials in Pulse-Echo Ultrasonic Evaluation of Thick Hybrid Composite Laminates

Significant challenges exist in inspecting thick composite laminates for manufacturing defects and operational damage. This is due to acoustic attenuation and impedance mismatch at the interface between the different composite layers. An innovative concept for enhancing ultrasonic testing of such composite laminates is introduced in this study. The proposed solution exploits the ability of acoustic metamaterials to cloak virgin composite. Herein, we show that by incorporating carefully designed metamaterials in a pulse-echo ultrasonic testing setup, the position and size of a delamination in a thick hybrid composite laminate can be determined accurately.

Preparation, characterization and properties of cinnamon essential oil nano-emulsion formed by different emulsifiers

Essential oil has unstable properties and low bioavailability. In order to improve these problems, with the help of ultrasonic wave, stable nano-emulsions were prepared with different emulsifiers. In this experiment, the formation of nano-emulsions with different emulsifiers at different concentrations was studied, including sodium caseinate (SC), whey glycoprotein (WGP), soy protein isolate (SPI) and Tween 80. Meanwhile, we studied the effect of ultrasonic cell disruption apparatus and homogenizer on the particle size of nano-emulsions. Cinnamon essential oil nano-emulsion prepared under the optimum emulsifier and its concentration has good microstructure and rheological properties. The stability of cinnamon essential oil nano-emulsion in different environments was studied, including centrifugation, freeze-thaw, heating-freezing and long-term (30 d) stability. The nano-emulsion of cinnamon essential oil is stable in emulsifiers. The nano-emulsions prepared by different emulsifiers has different particle sizes in different environments and their advantages and disadvantages are compared. Finally, how different nano-emulsion were digested in vitro was also studied. The in vitro digestion of nano-emulsion by different emulsifiers was simulated. Its properties include particle size, zeta potential and polymer dispersion index (PDI).

Piezo/sono-catalytic activity of ZnO micro/nanoparticles for ROS generation as function of ultrasound frequencies and dissolved gases

We report an accurate study on sonocatalytic properties of different ZnO micro and nanoparticles to enhance OH radical production activated by cavitation. In order to investigate some of the still unsolved aspects related to the piezocatalytic effect, the degradation of Methylene Blue and quantification of radicals production have been evaluated as function of different ultrasonic frequencies (20 kHz and 858 kHz) and dissolved gases (Ar, N2 and air). The results shown that at low frequency the catalytic effect of ZnO particles is well evident and influenced by particle dimension while at high frequency a reduction of the degradation efficiency have been observed using larger particles. An increase of radical production have been observed for all ZnO particles tested while the different saturating gases have poor influence. In both ultrasonic set-up the ZnO nanoparticles resulted the most efficient on MB degradation revealing that the enhanced radical production may arise more from bubbles collapse on particles surface than the discharge mechanism activate by mechanical stress on piezoelectric particles. An interpretation of these effects and a possible mechanism which rules the sonocatalytic activity of ZnO will be proposed and discussed.

Nanoemulsification of soybean oil using ultrasonic microreactor: Process optimization, scale-up and numbering-up in series

Ultrasonically-induced nanoemulsions have been widely investigated for the development of functional food, cosmetics, and pharmaceuticals due to ideal droplet sizes (DS), low polydispersity index (PDI), and superior physical stability. However, a series of frequently-used ultrasonic set-ups mainly suffered from a low ultrasonic energy efficiency caused by the large acoustic impedance and energy consumption, subordinately confronted with a low throughput, complicated fabrication with complex structure and weak ultrasonic cavitation. Herein, we employed a typical ultrasonic microreactor (USMR) that ensured the high-efficient energy input and generated intense cavitation behavior for efficient breakage of droplets and continuous production of unified oil-in-water (O/W) nanoemulsions in a single cycle and without any pre-emulsification treatment. The emulsification was optimized by tuning the formula indexes, technological parameters, and numerical analysis using Response Surface Methodology (RSM), followed by a comparison with the emulsification by a traditional ultrasonic probe. The USMR exhibited superior emulsification efficiency and easy scale-up with remarkable uniformity by series mode. In addition, concurrent and uniform nanoemulsions with high throughput could also be achieved by a larger USMR with high ultrasonic power. Based on RSM analysis, uniform DS and PDI of 96.4 nm and 0.195 were observed under the optimal conditions, respectively, well consistent with the predicted values. Impressively, the optimal nanoemulsions have a uniform spherical morphology and exhibited superior stability, which held well in 45 days at 4℃ and 25℃. The results in the present work may provide a typical paradigm for the preparation of functional nanomaterials based on the novel and efficient emulsification tools.

Association between characteristics of swallowing-related muscles and trunk muscle mass

Swallowing function is associated with systemic factors. Whether trunk or appendicular skeletal muscle mass is a better indicator of swallowing-related muscle characteristics in community-dwelling older adults is not clear. Hence, we investigated the association between the characteristics of swallowing-related muscles (e.g., mass and quality) and trunk muscle mass. Community-dwelling older adults aged ≥ 65 years (n = 141; men: n = 45, women: n = 96) were recruited for this cross-sectional observational study via a health survey conducted in 2018. Trunk muscle mass index (TMI) and appendicular skeletal muscle mass index (SMI) were measured using bioelectrical impedance analysis. Cross-sectional areas (CSAs) and echo intensity (EI) of the geniohyoid muscle (GHM) and tongue were evaluated using an ultrasonic diagnostic apparatus. Multiple regression analysis was used to examine the relationship of the characteristics of swallowing-related muscle with TMI and SMI. Multiple regression analysis showed that CSA of the GHM was positively associated with both TMI (B = 24.9, p < 0.001) and SMI (B = 13.7, p = 0.002). EIs of swallowing-related muscles were not associated with TMI and SMI. Trunk muscle mass was associated with swallowing-related muscle mass and not muscle quality. The results of this study shed light on the elucidation of association of dysphagia with TMI and SMI.

Ultrasonic measurement setup for monitoring pre-thawing stages of food

Abstract. The food industry relies on various technical processes, from storing, freezing, thawing, and packaging to logistics. With the increasing population and the equational growth in food production, it is preferred to have increased automation in the food industry to reduce human labor. To provide an automated and green solution, it is required to monitor and control food-processing steps, such as thawing. This research aims to design an ultrasound-based setup that can monitor the pre-thawing state of food. A change in the signal by 20 %–27 % for herring fish and 60.7 % for chicken soup was obtained when monitored from a frozen state to a room-temperature state. Various other sample food products were tested, and related challenges and observations are discussed.

Association of nocturnal sleep duration and sleep midpoint with osteoporosis risk in rural adults: a large-scale cross-sectional study.

Evidence has suggested the linkage between sleep habits and severalmetabolic diseases,but the association of sleep factors with bone health remains unclear, especially in regions with low economic levels. Thus, this study aimed to investigate the relationship of nocturnal sleep duration and sleep midpoint with the osteoporosis risk in arural population. Eligible subjects were derived from the Henan Rural Cohort Study. The Pittsburgh Sleep Quality Index was applied to collect sleep information including sleep initiating time and wake-up time. The bone mineral density of the calcaneus was measured by the ultrasonic bone density apparatus. Multivariable logistic regression models and restricted cubic splines were utilized to evaluate the odds ratio (OR) and 95% confidence intervals (95% CI). For 8033 participants, 1636 subjects suffered from osteoporosis. Compared with the reference group (7 ~ h group), the ORs and 95% CI of osteoporosis associated with duration of nocturnal sleep were 1.32 (1.10, 1.56), 1.59 (1.25, 2.01), and 1.82 (1.25, 2.65) in the 8 ~ h, 9 ~ h, and ≥ 10h group, respectively. Additionally, the adjusted ORs and 95% CI were 1.20 (1.01, 1.44) in the early sleep midpoint group and 1.09 (0.92, 1.29) in the intermediate sleep midpoint, compared with the late. Furthermore, there was a joint effect of long duration of nocturnal sleep and the early sleep midpoint on osteoporosis. Long duration of nocturnal sleep and early sleep midpoint were independently and jointly associated with higher risk of osteoporosis in rural areas. The Henan Rural Cohort Study has been registered at Chinese Clinical Trial Register (Registration number: ChiCTR-OOC-15006699). Date of registration: 06 July 2015. http://www.chictr.org.cn/showproj.aspx?proj=11375.

Solar Energy Based Object Detection and Automatic Speed Reducing Intelligence Robot Using Sensors

The average human life span has decreased since ancient times. Because the number of automobiles on the road is growing every day, the death rate from accidents has dramatically grown. Because brake failure causes so many accidents, we can lessen their impact when the brake is controlled automatically. A receiver and an emitter make up an ultrasonic setup that is put up in front of the vehicle. When an obstacle is recognized, the ultrasonic waves are always emitted by the ultrasonic emitter and are reflected back to the receiver, which then picks up the signal. The Arduino controller receives the signal from the reflected wave, and depending on the object's distance, it activates the buzzer and stops the car with LED indicators. motor used to move the vehicle.