Disinfection of drinking water is critical to prevent waterborne diseases. An unexpected consequence of water disinfection is the formation of disinfection by-products by the interaction of disinfectants with organic matter (natural or anthropogenic) and halides, which present significant toxicological effects and carcinogenic risks. As an emerging disinfection by-product, halobenzoquinones (HBQs) have attracted increasing attention owing to their severe toxicity and high detection rates. The credible determination of HBQs is essential for further studies on their occurrence, toxicity, and control measures; however, HBQs are usually detected in drinking water at trace levels. Therefore, accurate and efficient analytical techniques are critical for HBQ determination and quantitation. In this study, a method based on solid phase extraction (SPE) combined with ultra performance liquid chromatography-triple quadrupole mass spectrometry (UPLC-MS/MS) was developed to determine 13 HBQs, including six chlorobenzoquinones, six bromobenzoquinones, and one iodobenzoquinone, in drinking water. One-liter water samples were added with 2.5 mL of formic acid, and 500 mL of each sample was collected for further enrichment. Pretreatment optimization mainly focused on the SPE column, washing solvent, and nitrogen blowing temperature. After extraction using Plexa SPE columns (200 mg/6 mL), the samples were washed with ultrapure water containing 0.25% formic acid combined with 30% methanol aqueous solution containing 0.25% formic acid, eluted with 6 mL of methanol containing 0.25% formic acid, and then nitrogen blown at 30 ℃. The UPLC-MS/MS parameters were optimized by comparing the results of two reversed-phase columns (BEH C18 and HSS T3) and various concentrations of formic acid in the mobile phase, as well as by establishing the best instrumental conditions. The separation of 13 HBQs was performed using an HSS T3 column (100 mm×2.1 mm, 1.8 μm) via gradient elution with a mixture of 0.1% formic acid aqueous solution and methanol as the mobile phase for 16 min. The 13 HBQs were detected using a triple quadrupole mass spectrometer equipped with a negative electrospray ionization source (ESI-) in multiple reaction monitoring (MRM) mode. Matrix-matched calibration curves were used to quantify the HBQs owing to intense matrix inhibitory effects. The results reflected the good linear relationships of the 13 HBQs and yielded correlation coefficients (r) greater than 0.999. The method detection limits (MDLs, S/N=3) were 0.2-10.0 ng/L, while the method quantification limits (MQLs, S/N=10) were 0.6-33.0 ng/L. The recoveries of the 13 HBQs were 56%-88% at three spiked levels (10, 20, 50 ng/L), and the relative standard deviations (RSDs, n=6) were less than or equal to 9.2%. The optimization method was applied to analyze HBQs in five drinking water samples. Four HBQs, namely, 2,6-dichloro-1,4-benzoquinone (2,6-DCBQ), 2,5-dibromo-1,4-benzoquinone (2,5-DBBQ), 2,6-dibromo-1,4-benzoquinone (2,6-DBBQ), and 2,6-dibromo-3,5-dimethyl-1,4-benzoquinone (2,6-DBDMBQ), were detected in the samples with detection rates of 100%, 20%, 80%, and 20%, respectively. The most frequently detected HBQ, 2,6-DCBQ, also exhibited the highest content (15.0-56.2 ng/L). The method showed high sensitivity, stability, accuracy, and efficiency, rendering it suitable for the analysis of 13 HBQs in drinking water. Compared with previous methods that mainly focused on 2,6-DCBQ and 2,6-DBBQ, the developed method achieved higher throughput and enabled the simultaneous analysis of 13 HBQs. The method presented in this study provides an opportunity to explore different types and concentrations of HBQs in drinking water, offers a deeper understanding of the occurrence of HBQs, and facilitates further studies on the health risks and control measures of these compounds.
Search from 250 M+ research papersSearch from 250 M+ research papers
Jan 1, 2024
Yinan Zhang + 9
Open Access