Types Of Radiation Detectors Research Articles

An irradiation system for nuclear and materials research in a medical cyclotron

Development and commissioning of an irradiation system and experimental setup for nuclear research and materials analysis in a medical cyclotron facility is described. The setup, Low Energy in-Vacuum Irradiation System-LEVIS, is installed at the end of the existing R&D beamline. The components of LEVIS and their functions are explained and the characteristics such as energy, current and profile of the beam are measured. Different types of radiation detectors are installed and tested in the chamber for future applications of non-destructive analysis methods.

Gamma radiation detector selection for CT scanner

Three types of gamma radiation detectors associated with distributed electronics namely, NaI (Tl), HPGe and LaBr3(Ce) are compared primarily focusing on electronic noise and scattering noise. Additionally, detectors of same make, material, size and electronics are also compared. A methodology is proposed to select the most suitable detector for computed tomography (CT) among the available options. Standard deviation parameter is employed to estimate electronic noise without performing CT experiment. Kanpur theorem-1(KT-1) is used to estimate the scattering noise quantitatively after verifying its sensitivity to scattering noise. The impact of scattering noise on CT profiles is evaluated using dice similarity dice coefficient. A good resemblance between KT-1 and dice coefficient is observed. A maximum difference of 56% in scattering noise is observed when five detectors used simultaneously instead of single detector whereas a discrepancy of 85% is observed between different types of radiation detectors. As far as ease of handling, operational and capital cost is concern one has to compromise minimum 12% of accuracy in CT reconstruction if NaI (Tl) detector is used with respect to best alternative available.The proposed methodology can be applied to measurement that require minimal scattering interference data other than CT experiments. The manufacturer can add noise level of detector as a characteristic parameter in the data sheet.

Optimization of 3×3 inch NaI(Tl) detector related to energy, distance and bias voltage

There are different types of radiation detectors (gas-filled, semiconductor, scintillator etc.) and various working principles (ionization, electron-hole pair production, excitation) used in radiation detection. It is important that any detector is selected according to its intended use and that the detector is operated under appropriate conditions. NaI(Tl) scintillation detectors are widely used in nuclear spectroscopic studies due to their known advantages. Prior to carrying out such studies, it is first necessary to know the response function of the detector against radiation under the expected operating conditions and to perform the appropriate calibrations. It is important that certain factors are optimized, such as the experimental setup (source-to-detector position, shielding, source activity etc.), gain, bias voltage, and shaping time, which can each significantly affect the response function. In addition, in computational studies based on experimentation, optimization is gain more significant since it is assumed that such experimental studies are carried out under optimum conditions. In this study, in order to determine the most suitable operating conditions for a 3 × 3 inch NaI(Tl) detector; a coaxial sample holder was manufactured to enable different source-to-detector distances (5–15 cm) to be tested, and spectra were then obtained using different bias voltages (750–850 V) and sources with different energies in the range of 81–1332 keV. Through the use of efficiency values obtained for each condition, line and 3D surface plots were drawn and the relations between efficiency and distance, energy and bias voltage examined. The results showed that the efficiency value had an exponentially decreasing characteristic that was dependent on the energy and source-detector distance, and had the highest value at a bias voltage of around 800 V.

PO-1761 Compare different types of radiation detectors used to determine the Quality Index on CyberKnife

PO-1761 Compare different types of radiation detectors used to determine the Quality Index on CyberKnife

Detection performance of pixelated lutetium-yttrium oxyorthosilicate (LYSO) scintillators for high-resolution photon-counting CT imaging.

High-resolution photon-counting detector (PCD) computed tomography (CT) imaging is increasingly used for several applications. Recent technological advances in CT instrumentation have introduced various types of radiation detectors. Therefore, this work aims at evaluating the lutetium-yttrium oxyorthosilicate (LYSO) scintillator for use in PCD CT from a detector point of view. To do so, a mini-CT prototype was designed and constructed based on the pixelated LYSO blocks. The detector comprises four 10 × 10 linearly arranged LYSO blocks coupled with four position-sensitive photomultiplier tubes. The prototype utilizes a point gamma-ray source along with a cone-beam collimator. An in-home MATLAB-based data processing software package was also developed for storing the list-mode data, event positioning, and energy windowing. A set of experiments were conducted to assess the performance of the constructed energy-resolved LYSO:Ce detector for mini-CT imaging. The results show good crystal identification for all blocks with a maximum peak-to-valley ratio of 3.48. In addition, the findings confirm that the developed detector is position-sensitive. The 20% energy window provides an optimal performance by simultaneously providing good crystal identification and a scatter removal factor of 0.71. A 96% uniformity was also observed when the detector was irradiated with a uniform flood. The spatial resolution of the mini-CT prototype in the x- and y-directions was calculated to be 0.9 and 0.93mm, respectively, corrected for a magnification factor of 2.5. It is concluded that the pixelated LYSO crystal is a promising alternative to the current detectors and would be the scintillator of choice for high-resolution PCD CT imaging tasks.

Explanation of Deep Learning–Based Radioisotope Identifier for Plastic Scintillation Detector

Radioisotope identification (RIID) is a representative application of deep learning for radiation measurements. Deep learning-based RIID models have been implemented in various types of radiation detectors; however, very few of these models have been interpreted using explainable artificial intelligence (XAI) methods. This paper presents an explanation of a deep learning–based RIID model for a plastic scintillation detector. The RIID task is defined as a multilabel binary classification problem, and the dataset is generated using a random sampling procedure. The identification performance is verified using experimental data. The experimental results demonstrate that the performance of the RIID models increased with the increase in the total counts of the dataset. Additionally, XAI methods are implemented, and their explanatory performance is verified for the spectral input. The domain knowledge of RIID for the plastic scintillation detector is that patterns near the Compton edge can be used as evidence for the existence of radioisotopes. Among the implemented XAI methods, integrated gradient and layerwise relevance propagation exhibited concurrence with the domain knowledge, with the Shapley value explanation method presenting the most reliable results.

MEASUREMENT OF THE REGENER-PFOTZER MAXIMUM USING DIFFERENT TYPES OF IONISING RADIATION DETECTORS AND A NEW TELEMETRY SYSTEM TF-ATMON.

Stratospheric balloons are a useful tool for the investigation of cosmic radiation at high altitudes and the tests of new detectors of cosmic radiation. Due to necessary data processing, the balloon gondola needs to carry, together with radiation detectors, additional supplementary sensors measuring humidity, temperature, location and orientation, altitude, atmospheric pressure, acceleration, etc. A newly developed universal system TF-ATMON, based on using already existing tools of the PX4 open-source project, enables apart from data recording and monitoring, also the possibility to trace the balloon gondola after the flight. The application was demonstrated on stratospheric balloon flight FIK-6. This flight was unique because three different types of radiation detectors were used at one flight. It enabled us to compare the altitude of the Regener-Pfotzer maximum measured with different types of sensors sensitive to a different type of secondary cosmic radiation generated in the atmosphere.

DOSE RATE MAPPING INSIDE THE STRAZ POD RALSKEM CALIBRATION FACILITY-MONTE CARLO APPROACH.

The gamma spectrometry is one of the fundamental methods used in nuclear technology with well-established procedures of data acquisition and evaluation. Yet with expanding possibilities of detection and data processing, the question of accurate calibration very often rises, since the traditional approach to calibration might not always be the most efficient. In our work, we focus on field spectrometry and present a way of utilizing an already established and well working calibration facility and expanding its scope for new types of radiation detectors.

Recent Progress in Halide Perovskite Radiation Detectors for Gamma-Ray Spectroscopy

Detecting hard X-rays and γ-rays with high energy resolution is critical for medical and industrial applications, high-energy fundamental physics, and homeland security. Two types of radiation detectors, indirect-conversion (scintillators) and direct-conversion (solid-state) detectors, are the most widely used technologies. Semiconductor-based detectors that can directly convert γ-rays into an electrical signal and operate at room temperature are especially important as portable and cost-efficient detectors with high sensitivity and energy resolution. Recently, lead halide perovskites have attracted enormous interest for γ-ray detection, and significant progress has been made toward practical detectors using perovskites as active materials. In this Review, we start with the fundamentals of γ-ray detection and review the recent developments in halide perovskite γ-ray detectors. The key factors affecting the detector performance are summarized. We also give an outlook on the field, with emphasis on the challenges to be overcome.

CubeSat Observation of the Radiation Field of the South Atlantic Anomaly

The movement of the South Atlantic Anomaly has been observed since the end of the last century by many spacecrafts equipped with various types of radiation detectors. All satellites that have observed the drift of the South Atlantic Anomaly have been exclusively large missions with heavy payload equipment. With the recent rapid progression of CubeSats, it can be expected that the routine monitoring of the South Atlantic Anomaly will be taken over by CubeSats in the future. We present one-and-a-half years of observations of the South Atlantic Anomaly radiation field measured by a CubeSat in polar orbit with an elevation of 540 km. The position is calculated by an improved centroid method that takes into account the area of the grid. The dataset consists of eight campaigns measured at different times, each with a length of 22 orbits (~2000 min). The radiation data were combined with GPS position data. We detected westward movement at 0.33°/year and southward movement at 0.25°/year. The position of the fluence maximum featured higher scatter than the centroid position.

‘Detektory Dla Szkół’: a pilot detector-lending project for Polish schools

This article presents the Polish project entitled ‘Detektory dla Szkół’ (‘Detectors for Schools’, throughout the paper referred to as ‘the programme’). It was developed at the Education and Training Division of the National Centre for Nuclear Research (Narodowe Centrum Badań Jądrowych, NCBJ) in Poland. The programme allows the schools to borrow from NCBJ two types of radiation detectors: Geiger–Müller counter and CosmicWatch detector(s). Student participation in the measurements is expected.

Development and application of chip calorimeter as an X-ray detector

Radiotherapy for cancer patients requires accurate measurement of the absorbed dose of radiation in a treatment planning step. Various types of radiation detectors are currently utilized for dose measurement. Among them, calorimeters are known to be the most precise detector for measuring absorbed dose, but their on-site application is limited by the large size of the equipment. We developed a miniaturized chip calorimeter for application as a radiation detector. The calorimetric radiation detector was built using micro/nano fabrication techniques, and consists of an SU-8 photoresist absorber and high-sensitivity vanadium oxide (VOx) thermistors. The thermistors had a temperature resolution of 135 μK, and the calorimeter showed a thermal conductance of 11 μW/K. The detector was irradiated with various X-ray dose rates from a linear accelerator, and the absorbed dose to SU-8 was measured. The detector responses showed high linearity with dose rates, demonstrating the feasibility of the radiation detector for practical uses.

A General-Purpose Digital Pulse Shape Discrimination Algorithm

Digital pulse shape discrimination (PSD) systems are widely used to extract various kinds of information from the shape of output pulses of radiation detectors. Such systems replace the traditional analog PSD circuits with numerical algorithms running on a digital processor, which makes them more flexible for implementing various PSD methods. However, the available digital PSD algorithms have been generally tailored to the characteristics of the concerned detectors, which limit their general use. Here, for the purpose of building a general-purpose digital PSD module, we present a PSD algorithm that, with minimum alterations, can be used with a wide range of radiation detectors. Our approach is based on using the cosine similarity measure to quantify the variations in the shape of detectors’ pulses with respect to the shape of a unit step pulse. The method is described in detail, and the results of the test experiments with different types of radiation detectors, including a boron tetrafluoride (BF3) proportional counter, a liquid scintillation detector, and high purity germanium (HPGe) detector are shown. The performance of the algorithm is also compared to that of the common rise time discrimination method.

Novel bismuth tri-iodide nanostructures obtained by the hydrothermal method and electron beam irradiation

Bismuth tri-iodide is a layered compound semiconductor which has suitable properties as material for ionizing radiation detection devices. Monocrystals and polycrystalline thin films have been studied for this application, but only recently, the development of nanostructures of this compound has emerged as an interesting alternative for using such nanostructures in new types of radiation detectors or for including them in other applications. Considering this, we present in this work BiI3 nanoparticles successfully synthesized by the hydrothermal method, using a Teflon-lined stainless steel autoclave, at a temperature of 180°C during 8–20h, with BiCl3 and NaI as source materials. We characterized the nanoparticles by X-ray diffraction (XRD), transmission electron microscopy (TEM) and electron dispersive spectroscopy (EDS). We obtained small rounded or hexagonal particles (10–20nm in size) and larger structures. The maximum orientation of the nanostructures is along the (0 0 l) family planes and occurs after 16h of synthesis, which arises as the best condition for obtaining BiI3 oriented nanostructures. When a 100kV TEM electron beam was converged on the larger structures, we obtained highly oriented BiI3 hexagonal and rod shaped nanostructures. We found that particles’ shape does not depend on the synthesis time. In addition, results were compared with the ones obtained for nanoparticles synthesized from solution. The present work is an advance in the synthesis of BiI3 nanostructures by the hydrothermal method, and is also the first step on seeking the amenable control of morphology and size of such structures using electron beam irradiation. This last process may be particularly appropriate for producing nanostructures for future applications in new devices.

Plug and Play Geiger-Muller Detector for Environmental Monitoring

A novel Plug and Play Geiger-Muller detector for environmental monitoring is reported that allows the integration and automatic configuration of Geiger-Muller detectors in a network containing heterogeneous sensors. A new Transducer Electronic Data Sheet for Geiger-Muller detector complying with the IEEE 1451.4 standard has been implemented to interface radiation detectors according to Plug and Play. The electronic specifications for Geiger-Muller detectors developed in this article are based on the newly proposed transducer template and modification of the standard calibration table template. Proposed templates may also be used for other types of radiation detectors with pulse output. To illustrate the Plug and Play capability with Geiger-Muller detectors, the details of detector implementation are included.

Characterization and evaluation of extended defects in CZT crystals for gamma-ray detectors

Material homogeneity is critical in achieving high-performance in all types of radiation detectors. This requirement is not inevitably satisfied in today's commercial detector-grade CdZnTe (CZT) material because it contains high concentrations of extended defects, in particular, Te inclusions, dislocation networks, and twin- and subgrain-boundaries that affect the energy resolution and the efficiency of the devices. Defects, such as grain boundaries and cracks that completely block charge-carrier transport are impermissible in CZT radiation-detectors at concentrations exceeding certain threshold values. Our group in Brookhaven National Laboratory (BNL) conducts systematic studies, detailing the roles of crystal defects in CZT detectors and the mechanisms underlying their formation and effects. We employ infrared transmission microscopy, white beam X-ray diffraction topography, and high-spatial-resolution X-ray response mapping to identify particular types of defects and reveal their relationship with the devices' performances. In this article, we summarize some of the most important results that our group obtained over the past 5 years.

A novel phantom model for mouse tumor dose assessment under MV beams.

In order to determine a mouse's dose accurately and prior to engaging in live mouse radiobiological research, a tissue-equivalent tumor-bearing phantom mouse was constructed and bored to accommodate detectors. Comparisons were made among four different types of radiation detectors, each inserted into the mouse phantom for radiation measurement under a 6 MV linear accelerator beam. Dose detection response from a diode, thermoluminescent dosimeters, and metal-oxide semiconductor field-effect transistors were used and compared to that of a reference pinpoint ionization chamber. A computerized treatment planning system was also directly compared to the chamber. Each detector system demonstrated results similar to the dose computed by the treatment planning system, although some differences were noted. The average disagreement from an accelerator calibrated output dose prescription in the range of 200-400 cGy was -0.4% ± 0.5 σ for the diode, -2.4% ± 2.6 σ for the TLD, -2.9% ± 5.0 σ for the MOSFET, and +1.3% ± 1.4 σ for the treatment planning system. This phantom mouse design is unique, simple, reproducible, and therefore recommended as a standard approach to dosimetry for radiobiological mouse studies by means of any of the detectors used in this study. The authors fully advocate for treatment planning modeling when possible prior to linac-based dose delivery.

A single scatter electron Monte Carlo approach for simulating gamma-ray stopping efficiencies of Geiger-Müller counters

Abstract In spite of their relatively poor gamma-ray stopping efficiencies, the Geiger-Muller (GM) counter is still preferred in many radioisotope gauges for industrial measurements. This is because these detectors exhibit a high degree of robustness in harsh environments, are relatively insensitive to temperature changes in the environment, and are inexpensive compared to other types of radiation detectors. These properties could make the use of GM counters very feasible in a number of industrial applications, such as gamma-ray tomography and gamma-ray density gauges, provided that their gamma-ray stopping efficiencies can be improved. The Monte Carlo (MC) method is a powerful computational physics tool that is utilized very often in the design of radiation detectors and radioisotope gauges. In this work a MC model for GM counters that is benchmarked with experiments at the primary photon energy of 59.5 keV is proposed. This is a specific purpose MC simulation code that, as opposed to publicly available general purpose MC codes, employs single scatter (or microscopic) electron transport and is currently under development. In this paper, the MC code is described in detail and the results of the specific purpose MC code are benchmarked with experiments and two general purpose MC codes, MCNP5 and PENELOPE. It was observed that the specific purpose MC code improved the reduced chi-square value when compared to MCNP5 and PENELOPE.

Measurement of natural background radiation intensity on a train

This work aims to measure different components of natural background radiation on a train. A radiation measurement system consisting of four types of radiation detectors, namely, a Berkeley Lab cosmic-ray detector, moderated (3)He detector, high-pressure ionisation chamber and NaI(Tl) spectrometer, associated with a global positioning system unit was established for this purpose. For the commissioning of the system, a test measurement on a train along the railway around the northern Taiwan coast from Hsinchu to Hualien with a distance of ∼ 275 km was carried out. No significant variation of the intensities of the different components of natural background radiation was observed, except when the train went underground or in the tunnels. The average external dose rate received by the crew of the train was estimated to be 62 nSv h(-1).

A cold plasma dielectric barrier discharge atomic emission detector for atmospheric mercury

An automated atmospheric elemental mercury analyzer based on the dielectric barrier discharge (DBD) atomic emission technique was developed. The instrument is based on a gold-on tungsten coiled filament preconcentrator fashioned from commercial quartz-halogen lamps, a DBD excitation source and a radiation detector. An in-house program provided system control and data collection. Several types of radiation detectors, e.g., charge coupled device (CCD) array spectrometers, photomultiplier tubes (PMTs) and phototube (PT) are investigated. An argon plasma provided better performance than a nitrogen plasma. With approximately 0.88 standard liters per min sampling rate and preconcentration for 2min, the estimated (S/N=3) detection limit was 0.12ng/L (Hg(0)), the linear range extended at least to 6.6ngHg/L. Typical RSD values for determination at the single digit ng/L level ranged from 2.8 to 4.9%. In 19 separate calibrations conducted over 7 days, the calibration slope had a standard error of 1%. The system was applied to the determination of atmospheric mercury in two different locations.