Types Of Nanofillers Research Articles

Multiscale dynamic behavior of imperfect hybrid matrix/fiber nanocomposite nested conical shells with elastic interlayer

This investigation delves into the free vibration characteristics of coupled nested conical shells (CNCSs) made of porous composite materials. These two conical shells are connected by a mid-layer of elastic springs. The composite materials used in the shells consist of epoxy, nanofillers, and fibers. Two types of nanofillers are considered: Graphene Nanoplatelets (GNPs) and Carbon Nanotubes (CNTs), while E-glass fiber is used as the fiber. The nanofillers are distributed in four different patterns within the shell section. Porosity is uniformly distributed along the shell section and characterized by a coefficient. The rule of mixtures is employed to ascertain the equivalent material properties of the hybrid materials, while the Chamis approach is utilized for three-phase materials. First-order shear deformation theory (FSDT) and Donnell's theory are utilized for modeling the conical shells. The governing equations of motion are established through Hamilton's principle are solved using the generalized differential quadrature method (GDQM). Seven different boundary conditions (BCs) are considered to encompass the full range of BCs for CNCSs and four type of BCs for single truncated conical shell (STCS). The solution's accuracy is verified, and the effects of various parameters on the natural frequency parameter (NFP) of the shell are investigated, such as BCs, circumferential wave number (n), nanofillers pattern, semi-vertex angle, nanofillers angle, and mid-layer stiffness. Initially, a comprehensive investigation into the vibration behavior of a STCS is presented, followed by an analysis of the NFP of the CNCSs. The results demonstrate that the stiffness of the elastic mid-layer significantly influences the NFP of the system. The orientation of the nanofillers in the shell can increase or decrease the NFP. Additionally, the relationship between mode number and n depends on the type of BCs of the shells.

Creating ultra-strong and recyclable green plastics from marine-sourced alginate-chitosan nanowhisker nanocomposites for controlled release urea fertilizer

In response to the pressing environmental challenge posed by petroleum-derived plastics, the development of green plastics derived from all-biomass nanocomposites offers promising solutions. However, conventional nanocomposites often prioritize enhanced stiffness at the expense of flexibility. We introduce sodium alginate (SA)/chitosan nanowhisker (CSW) nanocomposites, derived entirely from marine-sourced all-biomass, to create ultra-strong and flexible green plastics. Through the synergistic interaction between SA and CSW, these nanocomposites demonstrate simultaneous stiffening and toughening, overcoming the traditional trade-off. Two key mechanisms contribute: geometric reinforcement from the needle-like structure of CSW and electrostatic reinforcement at the interface between oppositely charged CSW and SA. Compared to control SA, the SA/CSW nanocomposites exhibit remarkable enhancements in tensile modulus, strength, and stretchability, by 49%, 85%, and 55%, respectively (7.6 GPa, 223.3 MPa, 14.7%). Cellulose nanocrystals, serving as a control, only stiffen the nanocomposites, adhering to the typical trade-off. Biodegradability in compost can be tailored based on the type of nanofillers. Due to the water resistance of CSW, SA/CSW nanocomposites are proven effective for the controlled release of urea fertilizer in agricultural applications. With recyclability and superior mechanical properties, these marine-sourced green plastics offer a sustainable alternative to conventional plastics, promising significant impact in the eco-plastic industry.

Influence of Gamma-Phase Aluminum Oxide Nanopowder and Polyester-Glass Recyclate Filler on the Destruction Process of Composite Materials Reinforced by Glass Fiber.

Recycling of composite materials is an important global issue due to the wide use of these materials in many industries. Waste management options are being explored. Mechanical recycling is one of the methods that allows obtaining polyester-glass recyclate in powder form as a result of appropriate crushing and grinding of waste. Due to the fact that the properties of composites can be easily modified by adding various types of fillers and nanofillers, this is one of the ways to improve the properties of such complex composite materials. This article presents the strength parameters of composites with the addition of fillers in the form of polyester-glass recyclate and a nanofiller in the form of gamma-phase aluminum nanopowder. To analyze the obtained results, Kolmogorov-Sinai (K-S) metric entropy was used to determine the transition from the elastic to the viscoelastic state in materials without and with the addition of nanoaluminum, during a static tensile test. The tests included samples with the addition of fillers and nanofillers, as well as a base sample without any additives. The article presents the strength parameters obtained from a testing machine during a static tensile test. Additionally, the acoustic emission method was used during the research. Thanks to which, graphs of the effective value of the electrical signal (RMS) were prepared as a function of time, the parameters were previously identified as extremely useful for analyzing the destruction process of composite materials. The values obtained from the K-S metric entropy method and the acoustic emission method were plotted on sample stretching graphs. The influence of the nanofiller and filler on these parameters was also analyzed. The presented results showed that the aluminum nanoadditive did not increase the strength parameters of the composite with recyclate as a result of the addition of aluminum nanofiller; however, its addition influenced the operational parameters, which is reflected in a 5% increase in the UTS value (from 55% to 60%).

The Impact of ZnO Nanofillers on the Mechanical and Anti-Corrosion Performances of Epoxy Composites.

Epoxy resins were reinforced with different ZnO nanofillers (commercial ZnO nanoparticles (ZnO NPs), recycled ZnO and functionalized ZnO NPs) in order to obtain ZnO-epoxy composites with suitable mechanical properties, high adhesion strength, and good resistance to corrosion. The final properties of ZnO-epoxy composites depend on several factors, such as the type and contents of nanofillers, the epoxy resin type, curing agent, and preparation methods. This paper aims to review the preparation methods, mechanical and anti-corrosion performance, and applications of ZnO-epoxy composites. The epoxy-ZnO composites are demonstrated to be valuable materials for a wide range of applications, including the development of anti-corrosion and UV-protective coatings, for adhesives and the chemical industry, or for use in building materials or electronics.

Application of a folded nanostructure reinforcement for the pole vault curved shell

Foldability capacity is now introduced as a novel nanofiller reinforcement production procedure using some operation to control the mechanical, thermal and electrical properties in the sport equipment. Application of this type of nanofillers in the curved structures like pole vault shell leads to a novel engineering and sport shell shape structures. This article is organized to suggest a vibration-based formulation for analysis of folded reinforced curved shell sport structure subjected to thermal and mechanical loading. Using computation of kinetic, strain and external energies, one can arrive the motion’s equations using the minimization of total energy and Hamilton’s principle. Using solution of the motion’s equations through an analytical approach, the parametric analysis is presented. The verified test is presented for confirmation of the solution and trend of results.

Structural, optical analysis, stress-strain, and dielectric properties of selenium oxide/LaFeO3/blend nanocomposites with tunable properties for optoelectronics and micro-supercapacitors

This work focuses on developing flexible nanocomposites by introducing two types of ceramic nanofillers into a biopolymeric blend for optoelectronic and energy-storing applications. Selenium oxide (SeO2) nanoparticles (NPs) and LaFeO3 NPs were prepared by hydrothermal and solid-state reactions, respectively, and incorporated into the polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) through the solution casting process. Transmission electron microscope and X-ray diffraction tests revealed the creation of hexagonal SeO2 and orthorhombic LaFeO3 NPs, with average sizes of 17 and 93 nm. The blend's degree of crystallinity was dependent on SeO2 NPs and LaFeO3 contents. The infrared absorption spectra revealed the interactions/complexation of the fillers with the blend reactive groups. The scan e-microscope (field emission mode) investigated the films' surface morphology and detected the elements they contain. LaFeO3/SeO2 content impacted stress-strain behavior, raised the tensile strength from 64 to 70.9 MPa, and dramatically lowered the strain at break and toughness. UV–vis-NIR measurements exhibited that the transmittance, extinction coefficient, and refractive index can be tuned by SeO2 and LaFeO3/SeO2 content. The direct (Eg.d)/indirect (Eg.id) band gaps were reduced from 5.25/4.9 eV to 4.95/4.7 eV. The dielectric parameters (constant, loss, energy density, and conductivity) were significantly increased after loading 5.0 wt% LaFeO3/SeO2. The dielectric moduli and Cole-Cole plots were also investigated. The structural modifications and enhancement of the optical features and dielectric parameters make the resulted samples the best candidates for optoelectronic devices and energy-storing applications such as sensors and supercapacitors.

The Study of Composite Materials Properties Based on Polymers and Nano-Additives from Industrial Wastes from Kazakhstan.

This research is aimed at studying the properties of polymer anticorrosion coatings based on ED-20 resin widely used in practice and industrial wastes. In this work, three basic types of nanoscale nanofillers were chosen: dispersed particles-microsilica, microspheres obtained at Kazakh enterprises, and carbon nanotubes. Physicochemical research methods were used in the research: a laser analyzer for studying the dispersibility of industrial waste and spectrometric research methods. The properties of materials were investigated by standardized methods. The obtained results show that the introduction of microsilica and microspheres obtained at Kazakhstani enterprises, used as additives, improves both the physical and mechanical properties of epoxy composites compared to the standard (control) material. The results of experiments have shown that the optimal content of additives of microsilica and microspheres provides an improvement in the physical and mechanical properties of epoxy composites in comparison with the standard (control) material. Studies have shown that the introduction of microspheres into ED-20 polymer increases impact toughness. The introduction of microsilica into the matrix contributes to the increase of elastic modulus. Experimental studies of optical properties of samples of carbon composite polymer films based on polystyrene (PS) with additives of carbon nanotubes C60 and C70 and multilayer carbon nanotubes were also carried out. The experimental results obtained for the optical properties of polymer composites based on basic polymers from solid waste and carbon nanotubes showed that the optical properties of polymer composites undergo noticeable changes.

Hybrid Piezoresistive 2D MoS2/PEGDA/PANI Covalent Hydrogels for the Sensing of Low‐to‐Medium Pressure

Wearable technologies are attracting increasing attention in the materials science field, prompting a quest for active components with beneficial functional attributes whilst ensuring human and environmental safety. Hydrogels are highly biocompatible platforms with interesting mechanical properties, which can be exploited for the construction of strain sensors. In order to improve the directionality of their strain response and combine it with electrical properties to fabricate piezoresistive devices, it is possible to incorporate various types of nanofillers within the polymeric network of the hydrogels. 2D materials are ideal nanofillers thanks to their intrinsic two‐dimensional anisotropy and unique electronic properties. Herein, the covalent functionalization of 2D 1T‐MoS2 is exploited to build robust hybrid cross‐linked networks with a polyethylene glycol diacrylate gel (PEGDA). The conductivity of this nanocomposite is also further improved by inducing the interfacial polymerization of aniline. The resulting free‐standing samples demonstrate a linear and highly reversible piezoresistive response in a pressure range compatible with that of peripheral blood, while also featuring good compatibility with human skin cells, thereby making them interesting options for incorporation into wearable strain sensors.

Designing innovative PAni-based adsorbents for CO2 capture via in-situ nitrogen plasma modification for sustainable development

Carbon dioxide (CO2) capture is a critical strategy in the fight against climate change. By implementing this innovative technology, CO2 emissions from diverse sources will be captured and neutralized, thereby mitigating global warming. For this purpose, novel sorbents were developed in this work by loading TiO2 and ZnO nanofillers into a polyaniline (PAni) system to form PAni–TiO2 (PT) and PAni–ZnO (PZ) composites. Following that, in-situ nitrogen (N2) plasma treatments were applied for 5 min to improve their surface nature and physiochemical properties. The CO2 capture qualities of modified PT and PZ sorbents were investigated, as well as physical assessments of their microstructure, nuclear magnetic resonance (NMR), morphology, contact angle, roughness, electrical optical, reactivity, stability, and adsorption capability, hardness, softness and electrophilicity properties. Bombardment of high-energy plasma species for 5 min was sufficient to optimize the crystallite size and crystallinity degree in both the PT5 and PZ5 systems. These enhancements may be related to the growth of protonated benzoid rings -NH+- as a result of plasma modifications to the structure of PAni and its transformation into emerald salt. In a similar vein, the SEM micrographs, porous topography and hydrophilic nature of the PAni composites varied with respect to the type of nanofillers and plasma level. The plasma treatment provided additional oxygen-containing functional groups as active sites for chemical interactions, including CO2 via chemisorption or physisorption, facilitating further reduction. Additionally, plasma activities assisted in shifting to a rougher surface (i.e.,Ra = 3.83 µm) as well as optimizing the energy band gap (1.57 eV), which can accommodate more CO2 molecules, thereby improving the capture efficiency. Moreover, the findings indicate that PZ5 is more desirable for CO2 adsorption since it possesses a 2.52-fold greater CO2 adsorption energy (-0.079 a.u) than pristine PZ0. In the future, our work opens up exciting new prospects to achieve desired performance from CO2 capturing compounds utilizing plasma technology.

Molecular insights into strengthening of biomineral apatite with carbon nanofillers: A simulation study

Biomineral apatite (Ap) has been widely utilized in clinical bone graft procedures for over 25 years. However, its lower tensile strength and fracture toughness compared to natural bone limit its application in large load-bearing systems. This approach aims to enhance the mechanical performance of Ap while preserving its bioactivity, thereby expanding its potential clinical applications. In this study, the creation and processing of carbon nanofiller-based Ap nanocomposites, including pristine and vacancy-defective carbon nanofillers, are investigated using molecular dynamics simulations. The mechanical behaviour of Ap nanocomposites reinforced with three types of carbon nanofillers (CNF) is examined: (i) three-dimensional metallic carbon nanostructure with interlocking hexagons T6B (beam-like), (ii) carbon nanotubes (CNT), and (iii) three-dimensional metallic carbon nanostructure with interlocking hexagons T6P (plate-like). The analysis encompasses detailing the methodology utilized for modelling the equilibrated structures of CNF/Ap nanocomposites, along with the characterization of their elastic parameters. Computational findings reveal the significant impact of CNT chirality, Aspect Ratio (AR) of T6B and orientation of T6P on the mechanical properties of the nanocomposites and observed inclusion of CNF enhances the mechanical properties compared with those of pure Ap. The findings indicate that the lower diameter CNT and smaller cross-sectional area of T6B exhibit higher tensile strength compared to the larger CNT diameter and larger cross-sectional area of T6B of the same length. Further, the analysis highlights the substantial influence of vacancy defects concentration on CNF on the mechanical behaviour of nanocomposites, with an increase in defects correlating to a decrease in the mechanical strength of both CNF and CNF-based nanocomposites.

Research on The Dielectric Property of Nano-doped Aramid Paper

Oil-paper insulation systems are widely used in high-voltage equipment. Reducing the dielectric constant of insulating paper can improve the dielectric coordination of the oil-paper combination system. At present, a large number of new synthetic insulation materials have been produced, and some new composite insulation papers have low dielectric constant and high electrical strength properties. This article studied the optimal process flow for preparing aramid paper in the laboratory, trial-produced laboratory hand sheets with three types of nanofillers at different doping concentrations, and conducted relative dielectric constant and dielectric loss tests to select Laboratory samples with the best performance; the main research results achieved in the paper are as follows: ①Researched and determined the optimal process flow for making aramid paper in the laboratory, explored the effects of different rolling pressures and rolling temperatures on the dielectric properties of the paper, and determined the optimal rolling temperature and temperature of meta-aramid paper. The pressures are 200℃and 0.3Mpa respectively. ②Meta-aramid paper doped with SiO2, TiO2 and x nanoparticles was prepared, and the relative dielectric properties of the three nanoparticles at the optimal doping amounts (15%, 3% and 4%, respectively) were compared. Constant and dielectric loss, it is determined that the dielectric properties of 4% C3N4 nanoparticle-doped paper are at a relatively excellent level. Compared with pure paper, its relative dielectric constant is not much different, and it can better cooperate with transformer oil. At the same time The dielectric loss is reduced, so nanoparticles of this type and concentration are used as fillers to improve the electrical properties of aramid paper.

High-temperature dielectric nanocomposite film of 2D Bi4Ti3O12/ABS with excellent energy storage performance

The utilization of high-temperature dielectrics in capacitive energy storage is of great significance in contemporary electronic systems. Nevertheless, the thermal stability of most emerging polymers exhibits a significant decline in their energy storage capacity as temperatures rise. In this study, a unique type of 2D Bi4Ti3O12 nanofillers was synthesized in order to improve the breakdown strength. A nanocomposite consisting of Bi4Ti3O12/poly(acrylonitrile-butadiene-styrene) (ABS) was synthesized with the aim of attaining enhanced dielectric characteristics and energy storage density under elevated temperatures. The Bi4Ti3O12/ABS nanocomposites exhibited notable temperature stability in relation to their dielectric and energy storage capabilities across a temperature range spanning from room temperature to 120 °C. Ultrahigh discharged energy density (Ue) of 12.44 J/cm3 for 3 wt%- Bi4Ti3O12/ABS nanocomposites and high efficiency of 87 % under 550 MV/m were achieved at room temperature. An excellent Ue of 9.12 J/cm3 and high efficiency of 86.2 % for 3 wt%- Bi4Ti3O12/ABS nanocomposites were also observed in 3 wt%- Bi4Ti3O12/ABS nanocomposites under 450 MV/m at 120 °C, which was 117 % and 114 % of ABS films. These capacitive performances could match or be higher than previously reported values for high-temperature capacitor applications.

Recent Advances in Nanoclay‐ and Graphene‐Based Thermoplastic Nanocomposites for Packaging Applications

ABSTRACTOver the past few years, thermoplastic nanocomposites reinforced with different types of nanofillers have seen widespread use in the automotive, pharmaceutical, food packaging and electronic sectors. Among the different nanofillers used to fabricate thermoplastic composite–based packaging materials, nanoclay and graphene are very beneficial for producing high‐barrier packaging materials. The high aspect ratio and large surface area of both nanoclay and graphene facilitate uniform filler dispersion and tortuous path in the thermoplastic matrix, which ultimately improves the physico‐mechanical, thermal and barrier to oxygen, water vapour and light as well as antimicrobial properties, which are key requirements for packaging materials. Because graphene nanomaterials are electrically and thermally conductive, these thermoplastic nanocomposites may display excellent electrical‐, thermal‐ and microwave‐shielding capabilities, allowing them to be used in electronic packaging. This review aims to summarize the preparation and characterization of thermoplastic nanocomposites based on different types of nanoclay, graphene and graphene derivatives, as well as their prospective applications in food and electronic packaging. This review paper also discusses the factors that can affect the performance and attributes of these packaging materials, such as processing conditions, types of nanofillers, functionalization or modification of nanofillers for better filler dispersion and so forth. This paper presents a comprehensive and state‐of‐the‐art article on nanoclay‐ and graphene‐loaded thermoplastic nanocomposite–based packaging materials.

Static and Dynamic Mechanical Behavior of Carbon Fiber Reinforced Plastic (CFRP) Single-Lap Shear Joints Joule-Bonded with Conductive Epoxy Nanocomposites

The potential of electrically conductive graphene nanoplatelets (GNPs)/epoxy, multi-walled carbon nanotubes (MWNCTs)/epoxy and hybrid GNPs-MWCNTs/epoxy nanocomposites as adhesives for out-of-autoclave (OoA) and in-the-field CFRP repair via Joule heat curing was investigated. Scanning electron microscopy revealed a good dispersion of the nanoparticles in the matrix in all the nanocomposite adhesives above their percolation thresholds, which led to a homogeneous distribution of the heat generated during Joule CFRP repair. The joints bonded with neat epoxy and the nanocomposites showed similar lap shear strengths, with the addition of nanoparticles enhancing the fatigue performance of the adhesively bonded joints relative to when neat epoxy was used as an adhesive and oven-cured. The interfacial and cohesive failure mechanisms were found to coexist in all the cases, with an increasing dominance of the cohesive when nanofillers were embedded into the adhesive. No effect of the specific type of nanofiller incorporated into the epoxy as the conductive component was observed on the mechanical performance of the bonded joints, with the adhesives containing MWCNTs showing similar results to those filled with GNPs at considerably lower loadings due to their lower percolation thresholds. The independence of the properties regardless of the curing method highlights the promise of these Joule-cured adhesives for industrial applications.

Metal and Metal Oxides Nanoparticles as Nanofillers for Biodegradable Polymers.

Polymeric materials, despite their many undeniable advantages, nowadays are a major environmental challenge. Thus, in recent years biodegradable polymer matrices have been widely used in various sectors, including the medicinal, chemical, and packaging industry. Their widespread use is due to the properties of biodegradable polymer matrices, among which are their adjustable physicochemical and mechanical properties, as well as lower environmental impact. The properties of biodegradable polymers can be modified with various types of nanofillers, among which clays, organic and inorganic nanoparticles, and carbon nanostructures are most commonly used. The performance of the final product depends on the size and uniformity of the used nanofillers, as well as on their distribution and dispersion in the polymer matrix. This literature review aims to highlight new research results on advances and improvements in the synthesis, physicochemical properties and applications of biodegradable polymer matrices modified with metal nanoparticles and metal oxides.

Recent Advances and Challenges in Polymer-Based Materials for Space Radiation Shielding.

Space exploration requires the use of suitable materials to protect astronauts and structures from the hazardous effects of radiation, in particular, ionizing radiation, which is ubiquitous in the hostile space environment. In this scenario, polymer-based materials and composites play a crucial role in achieving effective radiation shielding while providing low-weight and tailored mechanical properties to spacecraft components. This work provides an overview of the latest developments and challenges in polymer-based materials designed for radiation-shielding applications in space. Recent advances in terms of both experimental and numerical studies are discussed. Different approaches to enhancing the radiation-shielding performance are reported, such as integrating various types of nanofillers within polymer matrices and optimizing the materials design. Furthermore, this review explores the challenges in developing multifunctional materials that are able to provide radiation protection. By summarizing the state-of-the-art research and identifying emerging trends, this review aims to contribute to the ongoing efforts to identify polymer materials and composites that are most useful to protect human health and spacecraft performance in the harsh radiation conditions that are typically found during missions in space.

A micromechanical modeling approach for predicting the piezoelectric and mechanical properties of piezoelectric fiber-reinforced multiphase composites containing CNT/GNP hybrids

This paper focuses on the prediction of piezoelectric coefficients, Young’s moduli and shear moduli of unidirectional piezoelectric fiber/carbon nanotube (CNT)/graphene nanoplatelet (GNP)-reinforced polymer composites using a novel micromechanics modeling technique. The multiphase composite configuration is that piezoelectric fibers are embedded within a polymer matrix filled by CNT/GNP hybrids. Agglomeration of hybrid nanofillers as a significant factor is identified and incorporated in the micromechanical calculation. Parametric studies are carried out to understand the effect of volume fraction, size and dispersion type of carbonous nanofillers as well as the piezoelectric fiber volume fraction on the effective material constants of multiphase composites. It is found that in comparison with the piezoelectric fibrous composite, the piezoelectric fiber multiphase composite containing CNT/GNP hybrids shows better elastic and piezoelectric properties. Also, further improvement in effective properties can be obtained by increasing the length and percentage of CNTs and GNPs. But, degradation in the elastic and piezoelectric constants is observed by the agglomeration of CNT/GNP hybrids. The current results are found to be in close proximity with the experimental data and other numerical results available in the literature.

Dynamic damage constitutive model for UHPC with nanofillers at high strain rates based on viscoelastic dynamic constitutive model and damage evolution equation

This study established a dynamic damage constitutive model for ultra-high performance concrete (UHPC) with nanofillers, based on a viscoelastic dynamic constitutive model and a damage evolution equation. Ten types of nanofillers, including particle, tube and flake nanofillers, were incorporated to modify UHPC. The split Hopkinson pressure bar was used to obtain the relationship between stress and strain of UHPC specimens at a strain rate of 200/s-800/s. The experimental results indicated that the dynamic compressive strength of UHPC with nanofillers at strain rates of approximately 200/s, 500/s, and 800/s can reach 172.8 MPa, 219.6 MPa, and 275.9 MPa, respectively, reflecting an increase of 85.2 %, 76.5 %, and 53.9 % compared with the blank UHPC. The established dynamic damage constitutive model considered the damage accumulation with strains under dynamic loading. The fitting coefficients of the dynamic damage constitutive model, when compared against experimental results, range from 0.8796 to 0.9963, showing a higher accuracy compared with traditional Zhu-Wang-Tang (ZWT) viscoelastic model, especially at a strain rate of approximately 200/s.

Ceramic based nanocomposites with alumina-carbon nanotube reinforcement for improved energy absorption in sports-related injuries: Microstructural analysis and low velocity impact

This study aimed to investigate the impact of incorporating nanoparticles on the energy absorption properties of nanocomposites using low-velocity impact (LVI) testing and molecular modeling. Various types of thermoset polymer-based nanocomposites reinforced with carbon nanotubes (CNTs) and alumina were analyzed, and the effect of adding two types of nanofillers and microfiber as a filler material was investigated. The results show that the addition of nanoparticles significantly improved the elastic energy absorption properties of the nanocomposites at the atomic level. The LVI tests demonstrated that adding both types of nanoparticles, along with microfiber, significantly enhanced the energy absorption capacity of the four-phase composite under practical conditions. The scanning electron microscope (SEM) analyses revealed the morphology behavior of the nanoparticles. Incorporating both types of nanoparticles simultaneously with the polymer and fibers increased the elastic modulus by up to 163 %. These findings have significant implications for designing structures with energy-absorbing materials to reduce sports-related injuries. The use of nanocomposites with enhanced energy absorption properties can help to improve the performance of energy-absorbing structures and reduce the risk of sports-related injuries.

Current status of research on composite bipolar plates for proton exchange membrane fuel cells (PEMFCs): nanofillers and structure optimization.

The proton exchange membrane fuel cell (PEMFC) is an efficient and clean energy source with promising applications. However, drawbacks such as high cost and low durability limit its application. Bipolar plates are an important component of PEMFCs, which not only account for a large proportion of the price and quality, but also affect the performance and durability of PEMFCs. Unlike traditional graphite and metal bipolar plates, composite bipolar plates have the advantages of easy processing, low cost, and corrosion resistance, but their lower performance limits their practical applications. This paper firstly summarizes the current research progress of various nanofillers used to improve the performance of composite bipolar plates, and discusses the improvement of the performance of composite bipolar plates by different forms and types of nanofillers. The morphological characteristics of different types of nanofillers and their effects on the improvement of conductive pathways are also analyzed. Subsequently, the means of structural optimization of composite bipolar plates are summarized, and specific optimization methods for phase interface, graphite/resin dispersion morphology, and conductive network structure are discussed in detail. Finally, challenges are discussed. Overall, this review can provide a reference for future research on composite bipolar plates.