Types Of Insulators Research Articles

Temperature and Physicochemical Properties of Abnormal Heating Composite Insulators

Abnormal heating will reduce the insulation performance of composite insulators or even cause insulator fracture, and the abnormal heating phenomenon is more serious under high-humidity conditions. Therefore, in this paper, the voltage withstand test of abnormal heating composite insulators caused by aging and damp sheath, decay-like core rod, and contamination were carried out under different ambient humidity. The heating and discharge of composite insulators were observed by infrared thermal imager and ultraviolet imager, and its temperature characteristics were analyzed from the aspects of heating range, heating shape, and temperature difference. In addition, in order to study the abnormal heating mechanism of composite insulators, the micro-morphology, chemical groups and dielectric properties of the silicon rubber of composite insulators with aging and damp sheath and the decay-like core rod were also measured. It is found that the temperature characteristics of the three types of abnormal heating composite insulators are different, and the temperature difference increases with the increase of humidity. The deterioration of silicone rubber and core rod material is the internal reason for the abnormal heating of composite insulators, and high-humidity conditions will exacerbate the heating phenomenon.

Research on the Physical Properties of an Eco-Friendly Layered Geopolymer Composite

Building envelopes with natural fibers are the future of sustainable construction, combining ecology and energy efficiency. The geopolymer building envelope was reinforced with innovative composite bars and two types of natural insulation (coconut mats and flax/hemp non-woven fabrics) were used as the core material. A 10 mol sodium hydroxide solution with an aqueous sodium silicate solution was used for the alkaline activation of the geopolymers. The purpose of this study was to confirm the feasibility of producing geopolymer composites with insulating layers made of renewable materials, which would have compressive strengths like those of C25/30-grade concrete and thermal conductivity coefficients like those of lightweight concrete. This publication presents the results of physicochemical tests on the base materials (oxide (XRF) and mineral phase (XRD) analysis as well as morphology and EDS) and studies the physical (density measurements), mechanical (flexural and compressive strength tests) and insulating properties (thermal conductivity measurements) of the finished sandwich partitions. The composites achieved a flexural strength of 7 MPa, a compressive strength of up to 30 MPa and a decrease in the thermal conductivity coefficient of about 60%. The research demonstrates contribution to sustainable construction by developing geopolymer composites, offering both structural integrity and superior thermal insulation. This innovation not only reduces reliance on traditional, carbon-intensive materials but also promotes the use of eco-friendly resources, significantly lowering the carbon footprint of construction. The integration of natural fibers into geopolymer matrices addresses key environmental concerns, advancing a rapidly growing field that aligns with global efforts toward energy efficiency, waste reduction, and circular economy principles in building design.

Simulation of thermal radiation effects on the thermal properties of parietodynamic walls using an innovative model

The parietodynamic wall, a type of dynamic insulation, has been recognized as an effective technology to reduce energy loss in buildings by recovering heat energy through forced convection. However, current research on the thermal performance of parietodynamic walls has overlooked the influence of thermal radiation, a crucial factor in energy transfer within the air layers of these walls. To bridge this gap, an innovative simulation model was developed and experimentally validated. Employing simulation methods, we investigated the impact of thermal radiation on the thermal behavior of parietodynamic walls under various influencing factors. Our findings reveal that thermal radiation markedly increases heat loss. Specifically, at an emissivity of 1, thermal radiation contributes up to 80.7% to the heat transfer coefficient (HTC) of the parietodynamic wall. Moreover, for a parietodynamic wall without insulation, the HTC of this wall will increase by more than 268% when thermal radiation is taken into account, compared to when it is not considered. These revelations deepen our comprehension of the role of thermal radiation in parietodynamic walls and offer valuable guidance for the development of more energy-efficient buildings.

Method of calculation of temperature parameters and servic life of cable lines with a voltage of 10 kV

RELEVANCE. The paper presents a method for calculating the temperature parameters and service life of cable lines (CL) with a voltage of 10 kV for various types of insulation and operating conditions. Dependencies have been developed that are recommended for clarifying the parameters of the CL, taking into account different operating modes. The results of the study can be used for practical application and will contribute to reducing the number of accidents resulting from thermal breakdowns of CL due to incorrect selection of CL parameters.PURPOSE. To investigate the temperature parameters of 10 kV CL, taking into account various methods of laying them and load factors for the climatic conditions of the Republic of Tatarstan.METHODS. Methods for calculating the temperature parameters of CL and their service life, methods of statistical data processing, and methods for approximating functions are used. The ELCUT software package is used to visualize the results obtained during calculations. results. The results of calculations of the temperature parameters of 10 kV CL with paper-impregnated insulation (BPI), polyvinyl chloride plastic (PVC) insulation and polyethylene (PE) insulation during their laying in air, in the ground, in the ground in a pipe, taking into account the load coefficients of cable lines, are presented. The results of calculations of the service life of the CL are shown. The values of the optimal load coefficients of the CL are determined to reduce the rate of thermal aging of insulation under various operating conditions. conclusion. The results of the conducted research and calculations can be used to evaluate and select the optimal load of 10 kV CL at the stages of operation and design of power supply systems.

Effect of insulator matrix on electrical transport properties of iron-insulator discontinuous multilayers

This work presents the results of the study of structural and electrical transport properties of the iron-insulator discontinuous multilayers (DMIMs). SiO2, HfO2, and MgO were chosen as the materials for the insulating layers. The discontinuous multilayers were prepared by the sequential magnetron sputtering on ceramic substrates. Obtained systems were annealed at different temperatures in an Ar + N2(2 %) environment using an annealing furnace with a continuous gas flow. Crystal structure analysis showed that the effect of annealing on the crystal structure of the samples varies and depends on the annealing temperature and the type of insulator. It has been demonstrated that the formation of iron oxide during annealing can be reduced by using HfO2 as the insulating layer material. The resistivity and temperature coefficient of resistance variation with temperature and the effective thicknesses of the ferromagnetic layers were analyzed.

Anticipation of Large Intrinsic Spin Hall Conductivity in Mercury Chalcogenides: A First‐Principles Study

AbstractThe report carried out detailed first‐principle calculations of Mercury chalcogenides (HgX; X = Te, Se and S) using density functional theory, verifying the bulk band inversion property with different exchange‐correlation functionals. The Wannier function method is used to study the non‐trivial topology of HgX systems, spin Berry curvature, and intrinsic spin Hall conductivity. Quantized intrinsic spin Hall conductivity is observed in the HgX systems. Large intrinsic spin Hall conductivity is found in the systems due to a strong spin Berry curvature accumulation near the triply degenerate points in the Brillouin zone. Calculation shows that the intrinsic spin Hall conductivity for all three HgX systems has stable plateaus, with Mercury Telluride having a maximum width of up to 1.05 eV. The maximum intrinsic spin Hall conductivity of –931/e () is obtained in mercury sulfide, higher than the reported values for spin Hall conductivity and the plateau width in typical topological insulators such as , , and as well as in transition metal pnictides (TaX, X = As, P and N) and transition metal iridates.

Multi-objective optimization of rural residential envelopes in cold regions of China based on performance and economic efficiency

Building envelope renovation solutions are critical to building performance and post-renovation economics. Building renovation is easier to carry out if the impacts of building envelope renovation solutions on building performance and post-renovation economic efficiency can be foreseen and a more sustainable and efficient renovation design can be achieved. This paper explores the optimal design of building envelope renovation using genetic optimization algorithms and statistical analysis methods, taking the performance of the renovated building and the economic efficiency of the renovation solution as the starting points. In Qingdao, a cold region of China, a survey was carried out on typical rural areas in seven regions. The selected design variables include the external wall and roof insulation material type(TWall, TRoof), external wall and roof insulation thickness(δWall, δRoof), type of window construction(TWc), and area radio of the window to the wall(WWR). Minimization of total building energy consumption(E) and renovation cost(COSTRE) and after renovation maximization of the combined incremental cost-benefit ratio over a 20-year life cycle(CICBR20-year life-cycle), effective natural daylighting illuminance(UDI), and percentage of time spent in indoor comfort(PTC) were considered in the optimization of the envelope. The results show that in cold regions, different envelope renovation solutions affect the optimization objectives to different degrees; changing the south-facing window-to-wall ratio(S_WWR) has a bigger effect on E, PTC, and UDI; and choosing different TRoof has a bigger effect on COSTRE and CICBR20-year life-cycle. Renovation of the selected typical rural residence with the optimal solution results in an energy-saving rate(Re) of 53.08 %, an increase of 940.86 h/year in annual indoor comfort hours(HIC) and 377.00 h/year in annual effective natural lighting hours(HUDI).

Weak topological insulators, nodal-line semimetals, and Dirac semimetals in phononic crystal plates

Topological phases of matter help us to modulate elastic waves at the boundaries of mechanical systems with robustness against defects. Here, we propose to realize weak topological insulator phases, nodal-line semimetal phases, and Dirac semimetal phases in 2D mechanical systems. We implement this idea by theoretical analysis of tight-binding models and numerical simulations of phononic crystal plates based on the two-dimensional Su-Schrieffer-Heeger models. The topological nature of these topological phases is characterized by the topological invariants. The edge states, the visualization feature of the weak topological insulators, are observed unambiguously in the phononic crystal plates. Particularly, the robustness of these edge states against structural defects is verified by removing four single square plates from the center. Experimentally, we realize two types of weak topological insulators in 2D mechanical systems. This study fertilizes the topological phases in mechanical systems and opens excellent avenues for manipulating elastic wave propagation.

Three-dimensional reconstruction method for layered structures based on a frequency modulated continuous wave terahertz radar

The feasibility of employing a continuous-wave terahertz detection system for non-contact and non-destructive testing (NDT) in multi-layered bonding structures is assessed in this study. The paper introduces the detection principle of terahertz frequency modulated continuous wave (FMCW) radar and outlines the two-dimensional (2D) scanning platform, which integrates optical lenses, three linear actuators, a control platform, and data acquisition units. Experimental results on two types of insulation with prefabricated defects demonstrate the capability of terahertz waves for transparent inspection imaging. These results confirm the viability of terahertz FMCW detection technology as an advanced NDT tool for multi-layered bonding structures. However, the inherent limitations of terahertz wavelength and hardware systems pose challenges in discriminating reflection peaks on upper and lower surfaces. To address this issue, a local adaptive empirical wavelet coefficient modal decomposition (LAEWCMD) method is proposed to enhance the longitudinal discrimination ability of terahertz detection. The proposed method involves segmenting the 2D terahertz detection image into regions to differentiate between defective and non-defective areas. Continuous wavelet transforms (CWT) are then applied to the range signals of each region to derive continuous wavelet coefficients (CWCs). Subsequently, empirical mode decomposition (EMD) is performed on the CWCs to decompose them into intrinsic mode functions (IMFs) and residual signals. The 1st IMF is utilized for three-dimensional (3D) reconstruction, and the regions are fused to generate the final output. The effectiveness of the proposed method is validated on aircraft thermal protection structures (TPS), achieving high-precision 3D reconstruction. This offers a novel approach for the application of terahertz computed tomography imaging and NDT.

Mycelium-wood composites as a circular material for building insulation

In Europe, buildings account for 40% of the energy consumption and produce 36% of CO2 emissions. Renovation could be a great tool to decarbonize the building stock since it allows for a decrease in the operational energy required for buildings and is less material-consuming than new construction. Further benefits are brought by the usage of bio-based insulation materials that can drastically reduce embodied emissions and transform structures into factual carbon sinks. This study focuses on a particular kind of biogenic material, mycelium-wood composites, consisting of organic matter bound by the root structure of fungal organisms. This innovative insulation material was compared with traditional ones for the renovation of the building stock, with a focus on vertical components like walls in the Helsinki metropolitan area. To characterize mycelium-wood composites, density and carbon content information were gathered from the samples realized in the Politecnico di Milano MaBa.SAPERLab, while the production processes were included in a SimaPro model to obtain the GWP value. Different scenarios were then defined by two variables: the renovation rate of the building stock and the market penetration of mycelium-wood composites. For each scenario, the overall GWP and CO2 stored values were calculated. Results show the great potential of the innovative material that grants carbon storage in the building stock that could even surpass the amount stored in the 32,500 ha of forest in the area. However, this possibility is heavily influenced by factors independent of the type of insulation used that should be further investigated.

Methods for calculating the moisture discharge characteristics of insulators

This paper presents a detailed analysis and comparison of methods for calculating the moisture discharge voltage of insulators. The initial section provides a brief overview of the principles underlying air discharge along the surface of insulators, which is crucial for understanding moisture discharge processes. Two primary calculation methods for moisture discharge voltage are considered. The first method is based on Tepler's formula, which requires specific input data that can only be obtained experimentally. Although this approach is classical, it complicates practical application due to the difficulty of acquiring the necessary parameters under real-world conditions. The second method, described in the literature, relies on readily available data, significantly simplifying the calculation process. Based on this method, an automated tool for calculating the moisture discharge characteristics of insulators has been developed. The use of this tool reduces dependency on experimental data, providing accurate results with minimal time and resource expenditure. To demonstrate the effectiveness of the proposed tool, a moisture discharge characteristic calculation was performed for the insulator type LK 70-110. According to the analysis results, the moisture discharge voltage for this insulator is 549 kV, with a stress of 2.1 kV per centimeter of leakage current path length. These figures align with the average values obtained using the first method, confirming the reliability and accuracy of the new approach. The conclusions indicate that the second calculation method is fully satisfactory for standard insulator calculations. It can also be applied in specific conditions, such as under-chemo-substations, where precision and efficiency are critically important. Thus, the proposed calculation method can become an effective tool for engineers and researchers involved in the design and analysis of insulation systems. This work significantly contributes to the development and improvement of methods for assessing the moisture discharge characteristics of insulators, representing an essential step towards enhancing the reliability and safety of electrical networks and their operation.

Numerical Analysis of Combined Effect Hybrid Fibres and Fire Insulation on the Fire Resistance Performance of SCC Beams

The use of self-compacting concrete in structural members has become increasingly prevalent in various construction applications. However, these structures are susceptible to one of the most hazardous disasters, which is the fire. This paper presents a numerical investigation of the fire resistance performance of self-compacting reinforced concrete (SCC) beams, as well as a parametric study to assess the impact of hybrid fibres and fire insulation on enhancing their performance under fire conditions. The study is conducted by developing a 3D finite element (FE) model using ANSYS software, where temperatures are applied according to the ISO834 standard fire. Geometric and material nonlinearities are considered in the evaluation of the behaviour of beams under fire conditions. The developed FE model is validated by comparing the predicted results with those of the experimental tests in literature. The fire resistance performance of SCC beams was compared with that of normal strength concrete (NSC) beams. The parametric study is conducted using three types of fire insulation, namely Tyfo WR-AFP, CAFCO 300, and Carboline Type-5MD. The results showed that SCC beam has lower fire resistance performance than the NSC beam. However, the incorporation of hybrid fibres allows a 17% improvement in the fire resistance of SCC beams. The use of fire insulations has increased the fire resistance time of SCC beams, and more particularly Carboline Type-5MD insulation with an increase of 28%. The combined use of hybrid fibres and fire insulation improved the fire resistance of SCC beams by 43%.

Redesign of the electrical power and lighting network at ice cream parlor located in the city of Quito

Abstract This article proposes the redesign of the electrical power and lighting network in an Ice Cream Parlor located in the city of Quito to ensure continuity in the electrical service and a luminous level according to the UNE 12464.1 Standard, established in the country. For this purpose, a survey of all the electrical load installed in the organization was carried out, where the nominal parameters of each equipment were identified with the help of the nameplate of each one of them. Using the specifications of the Ecuadorian Construction Standard (NEC) and the data obtained from the electrical load survey, five (5) circuits for outlets were proposed, considering a possible expansion of small equipment and the ten (10) maximum outlets established by the aforementioned standard. Additionally, four (4) circuits were proposed to feed the power load. With respect to the lighting network, the DIAlux software is used to determine the number of lamps, luminaires and their location to comply with the luminous level indicated. Therefore, it was necessary to propose six (6) circuits in order not to exceed the fifteen (15) lighting points established by the NEC. For each circuit, the following was calculated: conductor cross section, overcurrent protection, type of insulation and the diameter of the corresponding conduit to protect the conductors. Finally, quotations were made for the materials required for the implementation of the project. From these, an organization is selected, based on the availability of the necessary materials, their cost and accessibility, compared to other suppliers. The total amount of the proposal is US$2,518.24.

Thermodynamic modelling of low fill levels in cryogenic storage tanks for application to liquid hydrogen maritime transport

One of the key challenges in transporting liquid hydrogen (LH2) in bulk onboard carriers is the requirement for high performance insulation to reduce the heat transfer and cargo boil-off losses. After unloading their cargo, carriers on the return voyage may retain a small amount of liquid (heel) to keep tanks relatively cold, as well as to chill down to the tanks prior to cargo loading. Therefore, there is an aim to reduce net heat transfer into the tank while minimising the required volume of heel. While practices are relatively mature in the liquefied natural gas (LNG) industry, it is not clear how this may differ for future LH2 carriage. In this study, a new analytical, lumped-mass model was proposed to predict vapour stratification and tank warm-up. A 40,000 m3 double-walled LH2 spherical tank was considered with vacuum perlite and polyurethane foam (PUF) insulation, and the effects of tank pressurisation and fill level on cumulative heat gain were investigated. The model pointed to key differences between the two insulation types. Heat gain in the vacuum perlite tank was not predicted to be sensitive to changes in fill level, while heat gain in PUF tank was predicted to be less sensitive to pressurisation. In each case, pressurisation was predicted to enable reductions in heel boil-off which offset any associated increase in cumulative heat gain. In comparing LNG and LH2, the model pointed to a slower thermal response of the LH2 tanks. Consequently, the increase in inner shell temperature was not expected to lead to significant reductions in environmental heat transfer into the tank. The findings of this study point to potential operational differences in the management of LNG and LH2 heel during the ballast voyage as well as considerations for vacuum insulated tanks.

Failure type and failure level detection of insulators according to monitored leakage current

Due to the ever-increasing growth of electric energy consumption, the production of high-quality, reliable and high-reliability electricity is very important. Therefore, it is essential to have distribution and sub-transmission networks with a good reliability factor. In power distribution and sub-transmission lines, it is necessary to somehow isolate the conductors under voltage from the towers, and insulators are used for this purpose. These insulators have two main tasks. One of the main tasks of insulators is to isolate (insulate) the line conductor from the body of the tower. The insulators must be able to isolate the high voltages of the lines from the body of the tower without having a leakage current, and on the other hand, the insulators must be able to withstand the mechanical forces resulting from the weight of the conductors and the applied forces caused by wind and ice. Also, leakage current is one of the important parameters for condition monitoring of insulators in power grid lines. Failure to inspect the insulation for contamination and health conditions will lead to insulator failure and will cause faults in the electrical system. Therefore, it is very important to monitor the condition of the insulator. Based on this, in this paper, according to the data related to leakage current and also according to the introduced wear out function, a procedure for measuring the condition of insulators has been obtained. Finally, the condition of each insulator will be determined according to the defined indicators. Also, the failure level of each monitored data will be obtained using sensitivity analysis.

Shrinkage characteristics of glass and mineral fibre insulation materials at elevated temperatures

The fire resistance of building assemblies can be determined through testing or by numerical modelling. As testing of building assemblies is expensive and time-consuming, the development of numerical modelling methods is gaining momentum. One of the challenges in modelling assemblies’ thermal performance is insulation dimensional shrinkage at elevated temperatures. To address this challenge, this paper presents a comprehensive experimental investigation into the shrinkage of glass and mineral fibre insulation materials under elevated temperature conditions. Initially, a series of tests was conducted to establish the temperature range within which significant shrinkage occurs for both types of insulation. Then, visual observations and measurements were recorded to assess the physical and dimensional changes of the insulation materials within the identified temperature range for shrinkage, indicating distinct responses of glass and mineral fibre insulation to thermal exposure. Compared to width and length variations, thickness reduction in insulation was more significant. Overall, the insulation thickness decreased as the exposed temperature increased. The glass fibre insulation completely melted at 710°C, while mineral fibre insulation disintegrated at 1000°C. In addition, empirical equations were derived to assess the thickness variations of these insulations at elevated temperatures, which can greatly enhance the accuracy of future thermal models under fire scenarios. Lastly, potential areas for future research are identified.

Linking energy efficiency and waste recovery to improve housing insulation and tackle energy poverty in south-central Chile

Given the environmental impact of the construction industry, sustainable solutions are increasingly needed to minimize the life cycle impacts of buildings by means of reusing renewable industrial waste. Abundant forest and farm waste exist in center-south Chile, with great potential to be used as thermal insulation and, thus, improve the livability of houses located in an area facing air pollution and energy poverty issues. This paper discusses two types of insulation produced and tested jointly with Germany-based Fraunhofer Institute for Wood Research (WKI)– using Chilean agroforestry waste: First, a flakeboard made of wood veneer chips; and second, a flexible substrate and a pressure resistant board made of wheat and oat straw. The main goal of this research is to assess, by means of digital modeling and experimental tests, the thermal characteristics and the resistance to humidity of these new insulation materials and their performance within construction solutions usually used in Chile. The benchmarks used were the most demanding national residential energy efficiency standard implemented to address air pollution and energy poverty, and the most demanding international standard, both for walls and roofing. The results of both insulation materials was promising, as they met the thermal performance and resistance to humidity requirements and show technical feasibility for the insulation market; in addition, they share the potential to be used in different types of buildings and construction solutions both in Chile and abroad, promoting a sustainable approach starting from the raw materials and the manufacturing process, through the buildings’ operations.

Upcycling of industrial footwear waste into nonwoven fibrous structures with thermal and acoustic insulation properties

The footwear industry significantly impacts the environment, from raw material extraction to waste disposal. Transforming waste into new products is a viable option to mitigate the environmental consequences, reducing the reliance on virgin raw materials. This work aims to develop thermal and acoustic insulation materials using polyester waste from footwear industry. Two nonwoven and two compressed nonwoven structures, comprising 80% polyester waste and 20% commercial recycled polyester (matrix), were produced. The materials were created through needle-punching and compression molding techniques. The study included the production of sandwich and monolayer nonwoven structures, which were evaluated considering area weight, thickness, air permeability, mechanical properties, morphology using field emission scanning electron microscopy, and thermal and acoustic properties. The nonwoven samples presented high tensile strength (893 kPa and 629 kPa) and the highest strain (79.7% and 73.3%) and compressed nonwoven structures showed higher tensile strength (2700 kPa and 1291 kPa) but reduced strain (25.8% and 40.8%). Nonwoven samples showed thermal conductivity of 0.041 W/K.m and 0.037 W/K.m. Compressed nonwoven samples had higher values at 0.060 W/K.m and 0.070 W/K.m. While the sample with the highest conductivity exceeds typical insulation levels, other samples are suitable for thermal insulation. Nonwoven structures exhibited good absorption coefficients (0.640–0.644), suitable for acoustic insulation. Compressed nonwoven structures had lower values (0.291–0.536), unsuitable for this purpose. In summary, this study underscores the potential of 100% recycled polyester structures derived from footwear and textile industry waste, showcasing remarkable acoustic and thermal insulation properties ideal for the construction sector.

Non-Abelian Braiding of Topological Edge Bands.

Braiding is a geometric concept that manifests itself in a variety of scientific contexts from biology to physics, and has been employed to classify bulk band topology in topological materials. Topological edge states can also form braiding structures, as demonstrated recently in a type of topological insulators known as Möbius insulators, whose topological edge states form two braided bands exhibiting a Möbius twist. While the formation of Möbius twist is inspiring, it belongs to the simple Abelian braid group B_{2}. The most fascinating features about topological braids rely on the non-Abelianness in the higher-order braid group B_{N} (N≥3), which necessitates multiple edge bands, but so far it has not been discussed. Here, based on the gauge enriched symmetry, we develop a scheme to realize non-Abelian braiding of multiple topological edge bands. We propose tight-binding models of topological insulators that are able to generate topological edge states forming non-Abelian braiding structures. Experimental demonstrations are conducted in two acoustic crystals, which carry three and four braided acoustic edge bands, respectively. The observed braiding structure can correspond to the topological winding in the complex eigenvalue space of projective translation operator, akin to the previously established point-gap winding topology in the bulk of the Hatano-Nelson model. Our Letter also constitutes the realization of non-Abelian braiding topology on an actual crystal platform, but not based on the "virtual" synthetic dimensions.

Practices to Improve the Sustainability of Australian Cold Storage Facilities

With the ever-increasing threat of climate change and global warming, ways to make energy intensive buildings, such as cold storage warehouses essential for food preservation, more sustainable need to be found. Some refrigerated warehouse owners may be unaware or unsure of the benefits obtainable from implementing sustainable practices and technologies. To search for innovations that could inform the owners and managers of cold storage warehouses about how to enhance their sustainability, convergent interviewing of subject matter experts was conducted. The resulting practices and processes were organized into a hierarchy that ranged from essential to best practices that can be implemented to improve the sustainability of refrigerated warehouses. Examples of these practices and technologies include ideal refrigeration systems, racking methods, and insulation types. To encourage the use of sustainable practices and technologies, more reporting on successful or unsuccessful applications of practices and technologies needs to be communicated. Applying change diagnostic tools such as convergent interviewing enables a practical and industry focused set of outcomes to be determined that can help drive change towards more sustainable cold storage warehouses in Australia.