Types Of Elastomers Research Articles

Exploring the potential of induced dipole-dominated electrorheological effect: advancing ER elastomers

Abstract Prior research has predominantly focused on traditional electrorheological (ER) effects while overlooking the transformative potential of induced dipoles in enhancing the overall performance of ER materials. In this study, we introduced a novel type of ER elastomer called induced dipole-dominated ER elastomer (ID-ERE). Through high-energy ball milling (HEBM) of the filler particles, the oxygen vacancies were produced within the particles that acted as local charge centers. In the presence of an external electric field (E), these oxygen vacancies induced the dipoles with significant dipole moments, thus amplifying the local electric field EL within the particle gaps. The powerful interactions of these dipoles significantly improved the overall performance of elastomer; the phenomenon referred to as the ID-ER effect. The viscoelastic results showed that ID-EREs have high field-induced storage modulus (G’ = 395.7 kPa), a significant increment in storage modulus (ΔG’ = 270.5 kPa) and high relative ER effect (ΔG’/G0 = 217.2%) at 3 kV mm−1. Additionally, after testing ID-EREs viscoelastic properties, it was discovered that excessive powder content leads to a decline in the elastomer’s performance. The results showed that ID-ERE’s viscoelastic, mechanical, dielectric, and overall efficiency is finer than the control ER elastomer (C-ERE) having unmilled TiO2 particles. Besides, the preparation method is straightforward, easily replicated, scalable, and cost effective. Thus, these ID-EREs should be a new generation of elastomer with the potential to be used in various automotive, robotics, construction, and electroactive actuators industries.

Studies on preparation of silicon-containing polyester via ring-opening polymerization and new type of elastomers derived from the resulting diols

Silicon-containing polyesters represent a novel class of polymers that integrate silicone and polyester units within their main chain. Polysiloxanes typically consist of flexible chain segments, while polyesters are characterized by their rigidity. The combination of these two components in the main chain offers the potential for tunable properties across a broad range. For the first time, a new organosilicon cyclic ester monomer (Si-Mon) was synthesized using a pseudo-high dilution condensation method. Both theoretical and experimental studies confirm that the ring-opening reaction site of Si-Mon is the ester group, rather than the Si-O-Si bond. Silicon-containing polyesters (SiPET-Series 1) with molecular weights exceeding 20,000 Da were efficiently and rapidly synthesized at room temperature, utilizing benzyl alcohol as the initiator and t-BuP4 as the catalyst. Organosilicon polyester diols (SiPET-Series 2) with varying molecular weights were produced using 1,4-benzenedimethanol as the initiator. Additionally, a new type of organosilicon polyester elastomer (SiPET-E) was developed by employing SiPET-Series 2 as the base gum and (2,4,6-trioxotriazine-1,3,5(2H,4H,6H)- triyl)tris(hexamethylene)isocyanate (THDI) as the crosslinking agent. The stress–strain behavior of SiPET-E is influenced by the molecular weight of SiPET-Series 2. Notably, SiPET-E exhibits remarkable properties; for instance, it demonstrates superelastic characteristics when the molecular weight of SiPET-Series 2 is 13,000 g/mol, achieving a tensile strength of 2.56 MPa and an elongation at break of 776 % without the use of reinforcing fillers.

Analyzing the impact of elastomer spiral bearings as seismic isolators in a reinforced concrete structure in Algeria

Over the past few years, Algeria has experienced numerous seismic events, particularly in the northern region of the country, due to its geographical position between the African and Eurasian tectonic plates. These earthquakes pose significant risks, leading to severe damage to both human life and property, including buildings and infrastructure. In response, civil engineers have increasingly advocated for the adoption of advanced seismic isolation techniques aimed at mitigating the transmission of seismic acceleration from the foundation to the superstructure. As a result, Algeria has seen the implementation of a few key projects incorporating seismic isolators, such as the Grand Mosque of Algiers. This article focuses on the design and analysis of the impact of typical aseismic elastomer spiral bearings in a reinforced concrete building located in the city of Oran, Algeria. The study utilizes ETABS software to evaluate the effectiveness of these bearings in enhancing the seismic resilience of the structure.

Development of a novel elastomer with unique properties as fire and radiation resistance

This study aims to create a novel, distinct form of elastomer with superior ability to resist fire, high resistance to radiation, and resistance to environmental conditions such as temperature and solvents. This type of natural-based elastomer was prepared using carboxymethyl cellulose CMC, polyacrylic acid PAA, crosslinked with tannic acid TA. Most techniques in elastomer manufacture technologies are unfriendly and participate in increasing carbon emissions. Gamma radiation was used as a clean tool for copolymerization and crosslinking the elastomer. The irradiation dose of 5 kGy with a rate of 3.32 kGy/h was enough to produce CMC/PAA/TA elastomer. The properties of the produced elastomer were investigated by Fourier-transformed infrared spectroscopy (FT-IR), X-ray diffraction, thermal gravimetric analysis (TGA), and limiting oxygen index (LOI). CMC/PAA/TA has high resistance to solvents such as acetone, benzene, HCl, and HNO3. The tensile strength is 3.376 MPa, the elongation percent is 501.689%, and the LOI value is 30%. The produced elastomer possessed excellent gamma radiation resistance. The elastomer was exposed later to 1864 kGy of gamma radiation without showing degradation and retained its properties, as confirmed by FTIR, TGA, and mechanical properties. After investigation, it can be inferred that the produced CMC/PAA/TA elastomer exhibited outstanding properties.

CROSSLINK DENSITY AND ITS DISTRIBUTION IN HEAT AND OIL RESISTANT ELASTOMERS BY DOUBLE QUANTUM NUCLEAR MAGNETIC RESONANCE

ABSTRACT Double quantum (DQ) nuclear magnetic resonance (NMR) was used to characterize the crosslink density, crosslink density distribution, and defect level in a series of heat and oil resistant elastomers. A wide range of defect levels, crosslink densities, and crosslink density distributions was measured, and results depended on elastomer type and compound formulations, including the vulcanization system. The sol fraction defect level generally correlated with the concentration of added plasticizer in the formulation. The presence of polar side chains appeared to cause additional dynamic contributions to the dangling chain end fraction. The large differences in elastomer composition and rubber formulations prevented meaningful correlation of the measured crosslink densities with the low strain modulus. Fast Tikhonov regularization and log normalization fitting of the corrected DQ build-up curve was extremely useful to provide insight into the modality and widths of the crosslink density distributions. A high degree of heterogeneity of the crosslink network of heat and oil resistant elastomers was found. Crosslink density distributions were explained in terms of the polymer chain structure comprised of monomer sequencing coupled with the position of the crosslinking sites. The type of vulcanization system had a lesser effect of the nature of the crosslink density distribution. The primary polymer chain crosslinking sites may become segregated from the continuous phase due to polarity differences seen in the microstructure of oil and heat resistance elastomers. The development of such micromorphologies can favor curative partitioning. The sole use of DQ NMR can provide valuable insight into the nature of the polymer chain structure and crosslink network in rubber.

Structure, mechanical, and dielectric properties of polypropylene blended with ethylene and propylene‐based elastomers

AbstractPolypropylene (PP) has been widely researched in power cable insulation due to its excellent resistance against high temperatures and high voltages. Since PP is too stiff for power cable extrusion, elastomers have been blended with PP to improve its stiffness. Although effects of elastomers on electro‐mechanical properties of PP have been widely studied, fundamental issues governing changes in dielectric properties of PP/elastomer blends have yet to be fully understood. This paper therefore reports on the properties of PP blended with ethylene‐based elastomer (EBE) and propylene‐based elastomer (PBE) by correlating their structural, mechanical, and dielectric investigations with respect to elastomer types and contents. The results show that blending increasing amounts of EBE and PBE improves mechanical flexibility of PP, with Young's modulus reduces by 53% at 40 wt% of elastomer content. Morphology‐wise, PBE demonstrates better compatibility with PP and less disrupted crystallinity compared to EBE. Furthermore, PP/PBE has better breakdown performance over PP/EBE, albeit that their breakdown strengths reduce with increasing elastomer contents. Specifically, direct current breakdown strength of PP/PBE reduces by only 21% at 40 wt% of PBE loading compared to 31% at equivalent EBE loading. Potential mechanisms governing breakdown changes are discussed with structural, mechanical, and dielectric interpretations.

Utilization of Nanocenospheres a waste material to improve the physical and rheological properties of SBS asphalt binders

The performance enhancement of asphalt binders by incorporating innovative additives has been a subject of significant research and industry interest. This study emphasizes the potential of Nano polymer composites as a promising additive for improving the performance of asphalt binders, providing valuable insights into developing advanced asphalt materials for sustainable road infrastructure construction and maintenance. It explores the utilization of nano cenospheres to amplify the attributes of Styrene-Butadiene-Styrene (SBS) modified asphalt binders. It introduces a novel approach by incorporating Nano polymer composites (NPC) comprising nanocenosphere particles and Styrene-butadiene-Styrene Particles. Nanocenosphere particles are the waste materials derived from coal combustion in thermal power plants. Styrene-butadiene-styrene is a type of thermoplastic elastomer, a synthetic rubber. A series of experimental tests, penetration, softening point, ductility, performance grading, temperature sweep, multiple stress and creep recovery, frequency sweep, linear amplitude sweep, and rutting aging index, is conducted to evaluate changes in physical and rheological properties. Results indicate that adding nano cenospheres particles in SBS asphalt binder enhances its softening point, elasticity recovery, rutting resistance, fatigue life, storage stability, and aging resistance compared to traditional SBS-modified asphalt binders. Statistical analyses were accomplished to comprehend the influence of the Nano polymer composites. This analysis provides valuable insights into the effects of nanocenospheres on SBS-modified binders. Through rigorous statistical analysis, a thorough interpretation of how the incorporation of nanocenospheres influences the attributes of Nano-polymer composites.

Bioinspired stiff–soft gradient network structure for high-performance impact-resistant elastomers

Traditional impact-resistance materials relying on the combination of supporting materials and energy-dissipation elastomers can effectively reduce shock load, yet the sharp interface between two types of materials causes discontinuous stress transfer and cracking. Here, inspired by the squid beak, we report a type of high impact-resistance gradient elastomers with large-scale modulus gradient with about three orders of magnitude (modulus range of 7 × 103 ∼ 7 × 106 Pa) and high energy dissipation (loss factor > 0.6) over a wide temperature range by diffusively introducing stiff polymers in a highly damping elastomer with controlled mechanical properties. Under the action of an external force, our gradient elastomers exhibit soft-while-stiff attributes, combining cushioning and support. In drop hammer impact tests, our gradient materials can reduce impact strength by 80 %, significantly better than commercial protective gear. It is worth mentioning that the modulus of the bottom layer matches that of the tissues for better protection.

Congestion of steric and electronic factors in α-diimine nickel precatalysts for high-temperature ethylene polymerization in accessing direct PE elastomer

In α-diimine-nickel catalysts mediated ethylene polymerization, the synergistic impact of steric and electronic factors plays an instrumental role in fine-tuning catalytic activity, polymer molecular weights, microstructure, as well as mechanical and elastic properties. In this study, a new series of nonsymmetrical bis(arylimino)-acenaphthene-nickel complexes was prepared and investigated for ethylene polymerization. These complexes feature both bulky N-2,6-dibenzhydryl-3,4,5-fluorophenyl imine and smaller N-2,6-di(R)-4-(R1)phenyl imine units [Ni2Me (R, = Me, R1 = H), Ni2Et (R, = Et, R1 = H) and Ni2iPr (R, = iPr, R1 = H), Ni3Me (R, R1 = Me), Ni2Et,Me (R, = Et, R1 = Me)]. The incorporation of both steric congestion and strong electronic withdrawal groups into the catalyst structure resulted in significantly improved catalytic performance: high thermal stability and exceptional activity were observed at both ambient temperature (21.24 × 106 at 30 °C) and industrially relevant temperatures (1.65 × 106 at 100 °C). Polymer molecular weights and branching degree were tunable by adjusting the ligand structure and reaction conditions. This correlation extended to mechanical and elastic properties, demonstrating high tensile strength at low temperatures and good elastic recovery at high reaction temperatures, consistent with typical polyolefin elastomers.

Dynamic characteristics optimization of elastomer for resistance strain force sensor

PurposeThis paper aims to provide a new method to study and improve the dynamic characteristics of the four-column resistance strain force sensor through the elastomer structure design and optimization.Design/methodology/approachBased on the mechanism analysis method, the authors first present a dynamic characteristic model of the four-column resistance strain force sensors’ elastomer. Then, the authors verified and modified the model according to the Solidworks finite element simulation results. Finally, the authors designed and optimized two types of four-column elastomers based on the dynamic characteristic model and verified the improvement of sensor dynamic performance through a hammer knock dynamic experiment.FindingsThe Solidworks finite element simulation and hammer knock dynamic experiment results show that the relative error of the model is less than 10%, which confirms the accuracy of the model. The dynamic performance of the sensors based on the model can be improved by more than 30%, which is a great improvement in sensor dynamic performance.Originality/valueThe authors first present a dynamic characteristic model of the four-column elastomer and optimize the four-column sensors successfully based on the mechanism analysis method. And a new method to study and improve the dynamic characteristics of the resistance is provided.

Aging and Small-sized Particles Release Characteristics of Tire Microplastics in Various Environmental Media

In recent years, research on microplastics has mostly focused on thermoplastic materials, and there is a lack of research on the pollution status and environmental behavior of tire microplastics, a type of rubber elastomers. In order to investigate the aging and small-sized particles release characteristics of tire microplastics in various environmental media, the aging process of two different tire microplastics, one for cars and the other for electric bicycles, was simulated in dry and aquatic environments under laboratory conditions. The results showed that the tire microplastics would be aged after 30 d of UV illumination, which was manifested by the roughness of the surface and the appearance of cracks and flaking. The Fourier infrared spectra showed that the carbonyl index of the surface also increased. In addition, tire microplastics released a large number of small sub-micron particles under the influence of UV illumination and hydrodynamic action, and the number of particles released from car tire microplastics in aquatic environments reached 694.8 million particles per milliliter of solution at 30 d of the UV light condition, among which 694.6 million particles with a particle size of less than 1 μm were released, which was approximately 100 times of that in the dark condition. The study showed that tire microplastics in aquatic environments were more susceptible to aging and released more small particles under light conditions and that car tire microplastics released more small particles than electric bicycle tire microplastics, posing ecological and environmental risks.

Geometrically exact 3D arbitrarily curved rod theory for dynamic analysis: Application to predicting the motion of hard-magnetic soft robotic arm

Magnetorheological elastomers are active materials which can be actuated by the applied magnetic field. Hard magnetic soft (HMS) materials, a type of magnetorheological elastomers, show great potential in the fields of biomedical engineering and soft robotics, due to their short response time, remote operation, and shape programmability. To exploit its potential, a series of theoretical frameworks of HMS rods have been developed, but they are mainly limited to the static rod models or classical curved rod models that fail to consider the effect of the “initial curvature” on the distribution of the stress. In this work, we develop a curved rod theory to predict the 3D dynamic motion of the rod-like HMS robotics under large deformation. Based on the geometrically exact rod theory, we include the heterogeneous initial length of the longitudinal fiber caused by “initial curvature” into our model and obtain the reduced balance equations of the HMS robotics. As a result, the “tension-bending” and “shear-torsion” coupling effects of curved rods emerge in the present model. A numerical implementation of our model based on the classical Newmark algorithm is presented. To validate our model, three numerical examples, including the dynamic snap-through behavior of a bistable arch, are performed and compared with the simulation or experiment results reported in literatures, which show a good agreement. Finally, we experimentally study the 2D and 3D static and dynamic motion of a quarter arc HMS robotic arm under an applied magnetic field of 10 mT, and our model gives a satisfactory prediction, especially for static deformation.

The role of cavitation in the toughening of elastomer nanocomposites reinforced with graphene nanoplatelets

The toughening of different types of elastomers through the incorporation of graphene nanoplatelets (GNPs) has been investigated. Both the tear strength and tearing energy are increased significantly through a combination of mechanisms such as debonding, pull-out and cavitation. The processes that occur ahead of a tear/crack tip in natural rubber filled with GNPs have been monitored in situ using synchrotron-based nanoscale X-ray computed tomography. The GNP particles are found to debond and form voids that grow under stress leading to considerable energy absorption. The mechanisms of cavitation and void growth are analysed theoretically and it is shown that voids need to be larger than ∼1 μm in size to grow in the triaxial tensile stress field ahead of the tear/crack tip. The high level of cavitation and void growth found for the elastomers filled with micron-sized GNP particles is suggested to be the reason why these nanocomposites have a high tear resistance.

Evaluation of elastomer suitability for CCUS: Chemical compatibility and rapid gas decompression in supercritical CO2

AbstractThe equipment of carbon capture, utilization, and sequestration (CCUS) infrastructure demands a range of elastomers fully compatible with CO2 phases. In this paper, the typical oilfield elastomers, perfluoroelastomer (FFKM), fluoroelastomer (FKM), tetrafluoroethylene propylene elastomer (FEPM), and hydrogenated nitrile butadiene rubber (HNBR), were studied for their chemical compatibility and rapid gas decompression (RGD) in 100% supercritical carbon dioxide (sCO2). At a given test condition, all selected oilfield compounds passed the ISO 23936‐2 acceptance compatibility criteria after 28‐day aging at 100 C and 34.5 MPa in sCO2. After aging, the elongations at break of the FFKM and FEPM compounds increased; tensile strength for FEPM decreased. In contrast to FFKM and FEPM, FKM and HNBR exhibited both lower elongations at break and lower tensile strengths. The moduli of the various elastomers consistently decreased after the sCO2 aging. The RGD testing revealed that all compounds were capable of passing the RGD ISO 23936‐2 criteria. Complementary material analyses by Fourier transform infrared spectroscopy and differential scanning calorimetry along with surface morphology analyses were also conducted to gain additional insight into the suitability of the selected elastomers for sCO2 service.

Dielectric Properties of Polypropylene Blended with Ethylene-Butene Elastomer for High Voltage Applications

In recent years, polypropylene (PP) has been tremendously explored in high voltage cable applications due to its outstanding thermal and electrical properties. Furthermore, PP is an environment-friendly material that can be recycled, thus making it a promising candidate to replace conventional crosslinked polyethylene. However, the stiffness and brittleness of PP need to be further modified so that it can be utilized for practical cable applications. Recently, elastomer blending has been one of the favorable methods used by the industry to modify PP flexibility. Unfortunately, different types of elastomers bring different compatibility in the PP matrix. In this paper, the dielectric performance of PP, when mixed with ethylene-butene elastomer (EBE), was investigated. The thermal behaviors and morphological analysis were identified by using a differential scanning calorimeter and scanning electron microscopy, respectively. Meanwhile, the direct current (DC) breakdown strength was set up referring to the ASTM D3755 standard. Based on the findings, EBE shows a certain degree of compatibility with PP, where uniformly distributed spots were observed. Although the addition of EBE slightly degraded the DC breakdown properties of PP, the performance of PP/EBE blends at low elastomer contents is still good enough compared to conventional XLPE.

ВЛИЯНИЕ ТЕМПЕРАТУРЫ И ПРОЦЕССОВ СТАРЕНИЯ МАТЕРИАЛА НА СИЛОВЫЕ ХАРАКТЕРИСТИКИ ПОЛИМЕРНЫХ ПОГЛОЩАЮЩИХ АППАРАТОВ ВАГОНОВ

Improving the dynamic qualities, traffic safety and increasing the inter-repair mileage of cars are urgent tasks of car-building industry. The most dangerous loads acting on the car are longitudinal loads during emergency driving modes, to reduce which inter-car shock absorbers (absorbing devices) are provided; their effectiveness must be ensured throughout the whole car life. The performance of polymer car absorbing devices depends primarily on the durability of the polymer, which is a kinetically activated process accelerated by repeated deformations and elevated temperature. The mechanism of the material ageing process depends on the structure of the material. Based on experimental laboratory studies and comparative field tests, ageing of elastomers of different classes have been identified, the dependences of the power characteristics of R-5P absorbing apparatus with two types of solid elastomer (based on rubber and a mixture of elastic thermoplastic with polyvinyl chloride plastic) have been constructed at normal and low temperatures, as well as after 6 years of operation. Recommendations are given to increase the resistance to crystallization and to ageing of polymer elements of absorbing devices. It is advisable to use the characteristics obtained in the paper when modeling the operation of absorbing devices with a solid elastomer, taking into account the operating time.

Effects of Thermal Cycling on the Mechanical Strength of TPU 3D-Printed Material

Fused Deposition Modelling (FDM) is a three-dimensional (3D) printing technology known for its low-cost rapid manufacturing of parts. Nowadays, various industries such as automotive, aerospace, and maritime are using this technology to manufacture 3D-printed parts that have undergone high temperatures. The material used in this study is the Thermoplastic Polyurethane (TPU), which is the most commonly-used type of Thermoplastic Elastomer (TPE) in 3D printing. This material is a combination of substances from the qualities and characteristics of both thermoplastic and vulcanized thermoset rubber. TPU has excellent abrasion resistance, hardness, chemical, and thermal resistance properties. In addition, TPU is a great fit for making hoses, gaskets, and seals due to its oil and grease resistance properties. Due to the growing application of 3D-printed materials at elevated temperatures, this study aims to characterize the tensile strength of TPU 3D-printed materials when thermal cycled. The test results concluded that the tensile properties of TPU 3D-printed specimens were significantly influenced by the number of thermal cycles it was subjected to. The samples that underwent four thermal cycles exhibited the highest modulus of elasticity and stress at 200% strain. While samples which underwent 2, 8, and 16 thermal cycles resulted to a higher modulus of elasticity and tensile stress at 200% strain than the untreated specimen.

Insights into the tiger stripe phenomenon of polypropylene and its blend in injection molding with a rapid heat exchange mold

AbstractTo examine the formation of tiger stripes (TS) phenomenon on the surface of the injection molding parts, a home‐made injection mold with a rapid heat exchange system and in situ measurement of pressure and temperature was designed and manufactured. Based on this special mold, the TS diagrams as a function of mold temperature and injection pressure for isotactic polypropylene (iPP) and its blend with a type of polyolefin elastomer (iPP/POE) were explored for the first time. It is found that there exists a critical mold temperature and a critical injection pressure for the TS appearance or disappearance in both systems. The critical temperatures of TS disappearance for iPP and iPP/POE are ~50 and ~ 120°C, respectively. As evidenced by the correlation between melt pressure drop and TS appearance, the wall slip mechanism is regarded as the main cause of TS formation. Compared with the critical shear stress of wall slip (σw) in totally molten PP, the lower σw value in this study further indicates that the wall slip could be facilitated by the crystallization of iPP during injection. Combined with white light interferometer, micro‐area x‐ray diffraction nanoindentation and scanning electron microscopy, it is demonstrated that the cloudy and glossy region of TS in pure iPP system could be distinguished by surface crystallinity. In the blend system, however, the rubber phase orientation as a dominant factor contributes to the glossiness of TS.

Selective Metallization of Thermoplastic Elastomers Based on Laser‐Induced Surface Activation

Laser direct structuring (LDS) technology successfully realized the selective metallization on thermoplastic elastomers. Polystyrene‐block‐poly(ethylene‐co‐propylene‐block‐polystyrene copolymer (SEPS) and polyether‐block‐amide (Pebax) containing 5 wt% Cu2(OH)PO4 are designed as LDS materials. Copper layers are obtained after NIR laser activation and metallization. The analysis of morphologies (optical microscope, scanning electron microscopy, confocal laser scanning microscopy), the chemical composition (X‐ray photoelectron spectroscopy [XPS], Raman, X‐ray diffraction), and the performance (scotch tape test, resistance) of materials before and after laser activation and metallization are carried out. The key to obtaining a high‐quality metal layer is as follows. 1) Cu2+ is reduced to copper (Cu0) with amorphous carbon acting as a reducing agent, and Cu0 acts as catalyst seeds in metallization. 2) The good adhesion between polymers and copper layers comes from the micropores etched by laser activation. In particular, XPS shows that 64.6% Cu2+ in SEPS/Cu2(OH)PO4 is reduced to Cu0, while only 18.4% Cu2+ in Pebax/Cu2(OH)PO4 is reduced after laser activation. Moreover, resistances of copper layers on SEPS/Cu2(OH)PO4 and Pebax/Cu2(OH)PO4 are 0.96 and 5.04 Ω, respectively. This study puts forward a way of fabricating flexible LDS materials. The prepared SEPS/Cu2(OH)PO4 composite is promising for shape variable decoration and flexible electronic devices.

Enhanced bending electromechanical properties of maleic anhydride-grafted SEBS gels by blending with acrylonitrile-styrene copolymer

The poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS) gel which a type of electroactive thermoplastic elastomer has significant intrinsic electromechanical coupling effect owing to its unique microphase separated structure. However, the relationship between the structure and electromechanical properties of SEBS gel remains incompletely understood. This study investigates the effects of polar groups and nanostructure parameters on the bending electromechanical property of SEBS gel for improving its bending electromechanical properties, using maleic anhydride-grafted SEBS/white oil (WO) gel (SEBS-M gel) and blends of SEBS-M gel with acrylonitrile-styrene copolymer (SAN). The SEBS-M gel/SAN films exhibited a hexagonally packed cylinder (HEX) morphology, and the radius of polystyrene domains (rPS) as well as the thickness of poly(ethylene-co-butylene) (PEB) domains (dPEB) in the SEBS-M gel/SAN slightly decreased with increasing SAN content up to 15 phr, followed by an increase. The bending displacement and actuation stress of SEBS-M gel/SAN increased with increasing SAN content up to 15 phr. The bending displacement of SEBS-M gel at 1.4 kV is approximately 74 % of that of SEBS gel, while the bending displacement of SEBS-M gel/SAN-15 at 1.4 kV is approximately 195 % and 266 % higher than that of SEBS gel and SEBS-M gel when the SAN content reaches 15 phr, respectively. The grafted maleic anhydride has a counteractive effect on the bending electromechanical properties of SEBS gel, while blending with a certain amount of SAN in SEBS-M gel has a synergistic effect on the bending electromechanical properties of SEBS gel. It is demonstrated that the enchantment of bending electromechanical properties of SEBS gel is achieved not only by adjusting the parameters of its microphase-separated structure but also by inducing segment deformation through electric field-induced dipole orientations.