Type Total Knee Arthroplasty Research Articles

Mobile medial pivot (lateral slide)-type total knee arthroplasty exhibited different motion patterns between under anaesthesia and weight-bearing condition.

Total knee arthroplasty (TKA), which has medial pivot and mobile-bearing mechanisms, has been developed and clinically used. However, the in vivo dynamic kinematics of the mobile medial pivot-type TKA (MMPTKA) is unclear. This study analysed the in vivo kinematics of MMPTKA in weight-bearing and nonweight-bearing conditions. The study included 10 knees that underwent primary TKA using MMPTKA. After TKA, lateral view radiographs of the knee in full extension, 90° of flexionand passive full flexion were taken under general anaesthesia in the nonweight-bearing condition. At least 6 months postoperatively, knee motion during squatting from a weight-bearing standing position was observed using a flat-panel detector and analysed using the three-dimensional-to-two-dimensional image registration technique. Under anaesthesia: in passive full flexion, the anteroposterior (AP) locations of the femoral component's medial and lateral distal points were 10.2 and 16.0 mm posterior, and the rotational angles of the femoral component's X-axis (FCX) and insert were 8.1° external rotation and 18.5° internal rotation to full extension, respectively. Squatting: the AP translations of the femoral component's medial and lateral most distal points were 2.2 and 6.4 mm, and the rotational angles of the FCX and insert were 5.7° and 1.6° external rotation, respectively. Significant differences were observed in the AP translation of the femoral component's medial and lateral most distal points and changes in the insert's rotational angle when comparing under anaesthesia and squatting. The kinematics of the insert in MMPTKA was significantly influenced by loading and muscle contraction. The femoral component exhibited substantial external rotation and posterior translation under anaesthesia, which may contribute to achieving an optimal range of motion. The insert remained relatively stable during squatting and minimal rotation was observed, indicating good stability. MMPTKA was expected to demonstrate rational kinematics by incorporating mobile and medial pivot mechanisms. Level IV,prospective biomechanical case series study.

Tibial implant design in primary TKA: retrospective comparison of two designs for the occurrence of radiolucent lines and aseptic loosening.

The purpose of this retrospective study was to study the effect of tibial implant design on the occurrence of radiolucent lines (RLLs) and aseptic loosening (AL) by comparing two different total knee arthroplasty (TKA) designs. Two types of total knee arthroplasty,different for tibial shape, size andkeeldesign were compared, 255 for the first and 774 for the second. The occurrence of RLLs and radiological signs of micro- and macro-mobility and aseptic looseningwas analyzed. Demographic data were compared, as well as the type and rate of RLLs, occurrence of aseptic loosening and the presence of potential risk factors. The first implant designis morphometric and has a squarer keel than the second implant TKA. The overall rate of RLLs was similar(21%vs 23%), despite of a significantly lower rates of radiological signs of macro-mobility of the tibial component with the first implant(2% vs 17%). Survivorship of both designs was overall comparable(99.6% vs 98.8 %) the first implantgroup had more potential risk factors for poor bone quality than the secondgroup (p<0.05). A morphometric design is more anatomic and offers better bone coverage of the epiphyseal tibial surface. RLLs, as a sign of implant micro-mobility, were equally present in both designs. Radiological signs of macro-mobility at the metaphysiswere less frequently observed in squared keel design. The morphometric implant did not show improved survivorship compared with a symmetric implant. III.

Postoperative Intravenous Iron Supplementation Increases Hemoglobin Level in Total Knee Arthroplasty.

Iron supplementation provides iron storage and facilitates effective production of hemoglobin. The purpose of this study was to investigate the effect of early postoperative intravenous (IV) iron supplementation in different types of total knee arthroplasty (TKA) surgery. We retrospectively analyzed 863 patients who underwent TKA between September 2017 and September 2021. The IV iron (I) and non-IV iron (NI) groups were compared. Hemoglobin responders, defined as patients who showed a change in hemoglobin level of ≥2 g/dL at 6 weeks of surgery compared to the baseline immediate postoperative hemoglobin level, were identified and they were compared with the nonresponders. After logistic regression analysis, the patients were classified according to the type of surgery (unilateral TKA, staged bilateral TKA, and simultaneous bilateral TKA). A subgroup analysis was performed according to the comorbidity as Charlson Comorbidity Index (CCI). The type of surgery and the rate of hemoglobin responders differed between the I and NI groups. The surgery type and iron supplementation significantly affected the hemoglobin responder in the logistic regression model. In each surgery type, hemoglobin drop in the I group was generally lower in the second and sixth weeks than that in the NI group. It was also effective in reducing hemoglobin drop on the first day of the second surgery in staged bilateral TKA. In addition, the number of hospital days was lower in the IV iron supplementation group who underwent a staged bilateral TKA. CCI did not affect hemoglobin responder, hemoglobin drop, and transfusion rate in both the I and NI groups. Postoperative IV iron supplementation affected the outcome of hemoglobin responders. In addition, it reduced early postoperative hemoglobin drop. However, iron supplementation did not affect the transfusion rate, complications, and clinical outcome, regardless of the type of surgery. LEVEL OF EVIDENCE: Level III, case-control study.

The clinical results of bi-cruciate vs posterior stabilized total knee arthroplasty for flexion contracture in osteoarthritic knee.

The improvement of flexion contracture is important in knee arthroplasty since residual flexion contracture postoperatively is associated with decreased quality of life and patient satisfaction. In this study, we investigated the effect of bi-cruciate stabilized (BCS)-type total knee arthroplasty (TKA) as compared to posterior stabilized (PS)-type TKA on osteoarthritic primary knees with flexion contractures. 59 TKAs from January 2014 to December 2020, of which 30 were PS-type TKAs (NexGen LPS-flexⓇ; 76.3years, BMI 27.5) and 29 BCS-type TKAs (Journey IIⓇ; 72.5years, BMI 28.6), were performed for knee osteoarthritis with preoperative flexion contracture of 15° or greater. Full extension was obtained intraoperatively during all TKAs. Clinical outcomes, radiological evaluations, and the amount of additional distal femoral osteotomy during TKA were evaluated in a retrospective study design. The range of motion improved in the both groups. Postoperative flexion contracture was significantly improved in the BCS group. Knee Society Score improved significantly in both groups, with no difference between the two groups. The amount of additional distal femoral osteotomy was 2.5 ± 1.3mm for the PS group, and 1.8 ± 1.5mm for the BCS group, showing a significant difference (p = 0.04). The BCS-type TKA significantly improved preoperative flexion contracture and reduced the amount of additional distal femoral osteotomy compared to PS-type TKA. This is attributed to the anterior cam in the BCS-type TKA, which leads to a smaller amount of protrusion of the posterior femoral condyle from the posterior margin of the tibial component in the BCS-type in knee extension, as compared to the PS-type.

Intraoperative femoral rotational kinematics are similar in varus and valgus knees during medial pivot total knee arthroplasty

BackgroundMedial-pivot type total knee arthroplasty is designed to reproduce physiological femoral rotational kinematics during knee flexion; however, its rotational kinematics in valgus knees remain unknown. This study's hypothesis is that its kinematics show the similar medial pivot motion in valgus knees as in varus knees. MethodsThis retrospective study included 50 cases of primary medial-pivot type total knee arthroplasty performed with navigation for knee osteoarthritis. Cases were grouped as valgus (n = 20) or varus (n = 30). In valgus knees, surgeons used preoperative manual testing to confirm that alignment was correctable. They evaluated femoral rotational kinematics at maximum extension, 30°, 60°, 90°, and maximum flexion, using a navigation system, both before and after implantation. Finally, intraoperative rotational kinematics, postoperative patient-reported outcomes, and knee range of motion were compared between the two groups. FindingsBefore implantation, both valgus and varus knees displayed external femoral rotation relative to the tibia during knee flexion. The rotation magnitude was significantly larger in varus knees at 60°, 90°, and maximum flexion angles compared to valgus knees (P < 0.05). In contrast, after implantation, both groups displayed external femoral rotation of 12–13° during knee flexion with no significant differences between the two groups at any knee flexion angle tested (P > 0.05). Short-term clinical outcomes were comparable between valgus and varus knees. InterpretationPostoperatively, medial-pivot type total knee arthroplasty for knee osteoarthritis resulted in external femoral rotation during knee flexion. Notably, this occurred even in valgus knees with good short-term clinical outcomes.

Influence of posterior tibial slope on postoperative outcomes after postero-stabilized and condylar-stabilized total knee arthroplasty.

To compare clinical outcomes and surgical times of two different types of total knee arthroplasty(TKA), postero-stabilized(PS) and condylar-stabilized(CS), in relation to posterior tibial slope(PTS) values and the deviation of these values from the surgical technique. 168 patients undergoing TKA surgery between 2016 and 2020 met our inclusion criteria. For each case, gender, age at surgery, operating time, type of implant and preoperative PTS(preop-PTS) and postoperative PTS(postop-PTS) measurements were collected; difference(∆PTS) between preop-PTS and postop-PTS was also calculated. Short Form 12 Mental and Physical scores(SF-12M and P) and functional Knee Society Score(fKSS) were collected preoperatively and at a minimum of 12months postoperatively. Four subgroups were thus created in relation to PS or CS system and postop-PTS value(≤ 5°and > 5°). Of the 168 patients, 96 had a PS system and 72 CS system. Performing a CS-TKA took less time than a PS-TKA(p < 0.05). SF-12P showed better results(p < 0.05) in CS-TKA group than PS-TKA, probably because of the younger age of CS-TKA patients(p < 0.05). In the PS > 5° all examined postoperative scores were better(p < 0.05) than PS ≤ 5°, while only fKSS was better(p < 0.05) in CS > 5° than CS ≤ 5°. No significant difference(p > 0.05) in terms of postoperative outcomes between the PS > 5° and CS > 5° was noted, whereas only SF-12P was better in the CS ≤ 5° compared with PS ≤ 5°. Highest values of SF-12M and fKSS were obtained in the PS ≤ 5°, in which postop-PTS was closer to technique. When performing a PS-TKA, the best result was obtained with a postop-PTS > 5°, but comparable outcomes between the two systems were evident with postop-PTS > 5°. It is crucial to come as close as possible to the indications reported in surgical technique regardless ∆PTS.

A review on flexion angle in high-flexion total knee arthroplasty for indonesian’s need

Total Knee Arthroplasty (TKA) proposed as an alternative treatment for damaged knee joints of humans is reviewed. The commercial application of TKA can help patients to improve their daily normal activities. Here the high-flex type total knee arthroplasty (High-Flex TKA) is typically designed for the patient’s convenience on which the greater range of motion can be adjusted for extreme activities such as Seiza and Muslim praying. However, the present High-Flex TKAs have not fulfilled the needs of Indonesians for religious activities with a flexion angle of 150°–165°. Therefore, this review aims to examine the flexion range of High-Flex TKAs proposed for the needs of Indonesians. This study is a narrative review, all studies published and reviewed are related to the range of flexion angles on the use of products from many manufacturers and various types that have been used by patients, as well as the development of a CAD-based TKA design. It was proposed in the present study that the flexion angle on High-Flex TKAs may be optimized by thickening the posterior femoral condyle, creating a medial pivot system, and applying a single radius system on the femoral component. Whereas, the tibial insert component could be designed by setting up the posterior tibial slope, and creating a post-cam stabilizer mechanism. Many knowledge gaps related to the population of research objects, lack of research on extreme angles, development of TKA components, are discussed. Further needs of extensive research on TKA in Mongoloid races are anticipated to be introduced for extreme angles and most comprehensive product development for optimization of the flexion angle.

Comparison of the joint laxity of total knee arthroplasty evaluated by the distraction force and the varus–valgus force

BackgroundComponent gap (CG) measurement help surgeons evaluate intraoperative soft-tissue balance. One technique is measuring the CG using tensioner devices with distraction force. Another is to evaluate the laxity under a varus–valgus force using navigation or robotics. The aim was to compare the JL evaluated by CG and varus–valgus force between the different types of total knee arthroplasties. MethodsForty-three bi-cruciate stabilized (BCS) knees and 33 bi-cruciate retaining (BCR) knees were included. After bone resection and soft tissue balancing, the CG was measured and after the final implantation and capsule closure, JL under a maximum varus–valgus stress was recorded with navigation. JL evaluated by the CG (JLCG) was defined as CG minus selected thickness of the tibial component and JL under varus–valgus force (JLVV) was defined as difference between varus–valgus angles without stress and maximum varus–valgus angles under varus–valgus force. The evaluations were performed at flexions of 10°, 30°, 60° and 90°. ResultsAlthough JLCGs of lateral compartment of BCS were larger than those of BCR, no difference was found between JLVVs of BCS and BCR. Although JLCGs of lateral compartment did not change at each knee flexion angle in both BCS and BCR, JLVVs of lateral compartment increased by 3° from 10° to 90° knee flexion. ConclusionJLVVs of BCS and BCR were equivalent, whereas BCS showed larger JLCGs of lateral compartment. JLVVs of lateral compartment increased by 3° in the range from 10° to 90° knee flexion whereas JLCGs remained stable.

A Mid-term Comparison of the Functional Outcomes of Medial Pivot and Rotating Platform Mobile-Bearing Total Knee Arthroplasty in the Indian Population.

Both medial pivot (MP) and rotating platform (RP) mobile-bearing (MB) total knee arthroplasty (TKA) have been developed to better mimic the natural knee kinematics and femoral roll back in flexion. The purpose of this retrospective study was to compare the mid-term functional outcomes and range of motion (ROM) of MP and RP types of total knee arthroplasty. 116 patients (mean age of 66.3years) undergoing TKA (52 Medial pivot design and 64 Rotating Platform design) were evaluated retrospectively with Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) knee score, knee society score (KSS) with its subgroups namely, Knee Score (KSKS) and Functional Score (KSFS) and forgotten joint score (FJS) at a mean follow-up of 7.1years. Range of motion (ROM) and tibiofemoral anatomic angle on the radiographs were also compared. Mean ROM, WOMAC and KSKS improved significantly from pre-operative to postoperative knees in both the groups. There was, however, no significant difference between the two groups at the final follow-up. In contrast, mean KSFS score improved to 89.5 ± 8.1 in MP group and 86.3 ± 7.1 in RP Group (p = 0.025), while mean FJS was 85.6 ± 4.1 and 80.9 ± 5.4 in the MP and RP groups, respectively (p = < 0.0001). Satisfactory clinical and functional outcomes can be obtained using either a MP or RP knee joint in tricompartmental osteoarthritis of knee. The MP design scores better on the KSFS score and FJS than the RP-TKA.

Kinematics and center of axial rotation during walking after medial pivot type total knee arthroplasty

PurposeIn recent years, the medial pivot (MP) type total knee arthroplasty (TKA) implant has been developed and marketed for achieving more natural kinematics with MP. However, little is known about the pivot pattern during walking after MP type TKA. This study aimed to determine the kinematics and center of axial rotation during walking after MP type TKA.MethodsThis randomized prospective study enrolled 40 patients with MP type TKA, 20 with cruciate-substituting TKA (MP-CS group), 20 with posterior-stabilized TKA (MP-PS group), and 10 healthy volunteers (control group). The kinematics and center of axial rotation during overground walking were measured by a three-dimensional motion analysis system. The six-degrees-of-freedom kinematics of the knee were calculated by the point cluster method.ResultsThe amount of change in knee flexion in early stance phase was significantly lower in the MP-CS and MP-PS groups than in the control group. The femur showed anterior translation during early stance phase in all three groups. The median center of axial rotation in the transverse plane was predominantly on the lateral side of the knee during stance in all groups.ConclusionsKinematics during gait are thought to be determined by physical posture, the kinetic chain during weight-bearing, and the kinematic features of adjacent structures, such as the behavior of the biarticular muscles. MP-CS and MP-PS did not necessarily induce rotational motion centered on the medial ball-in-socket component during walking; translational and lateral pivoting movements were also observed. Long-term follow-up is needed to monitor for polyethylene wear and implant loosening.

Leveraging subject-specific musculoskeletal modeling to assess effect of anterior cruciate ligament retaining total knee arthroplasty during walking gait.

Bi-cruciate retaining total knee arthroplasty has several potential advantages including improved anteroposterior knee stability compared to contemporary posterior cruciate-retaining total knee arthroplasty. However, few studies have explored whether there is significant differences of knee biomechanics following bi-cruciate retaining total knee arthroplasty compared to posterior cruciate-retaining total knee arthroplasty. In the present study, subject-specific lower extremity musculoskeletal multi-body dynamics models for bi-cruciate retaining, bi-cruciate retaining without anterior cruciate ligament, and posterior cruciate-retaining total knee arthroplasty were developed based on the musculoskeletal modeling framework using force-dependent kinematics method and validated against in vivo telemetric data. The experiment data of two subjects who underwent total knee arthroplasty were obtained for the SimTK "Grand Challenge Competition" repository, and integrated into the musculoskeletal model. Five walking gait trials for each subject were used as partial inputs for the model to predict the knee biomechanics for bi-cruciate retaining, bi-cruciate retaining without anterior cruciate ligament, and posterior cruciate-retaining total knee arthroplasty. The results revealed significantly greater range of anterior/posterior tibiofemoral translation, and significantly more posterior tibial location during the early phase of gait and more anterior tibial location during the late phase of gait were found in bi-cruciate retaining total knee arthroplasty without anterior cruciate ligament when compared to the bi-cruciate retaining total knee arthroplasty. No significant differences in tibiofemoral contact forces, rotations, translations, and ligament forces between bi-cruciate retaining and posterior cruciate-retaining total knee arthroplasty during normal walking gait, albeit slight differences in range of tibiofemoral internal/external rotation and anterior/posterior translation were observed. The present study revealed that anterior cruciate ligament retention has a positive effect on restoring normal knee kinematics in bi-cruciate retaining total knee arthroplasty. Preservation of anterior cruciate ligament in total knee arthroplasty and knee implant designs interplay each other and both contribute to restoring normal knee kinematics in different types of total knee arthroplasty. Further evaluation of more demanding activities and subject data from patients with bi-cruciate retaining and posterior cruciate-retaining total knee arthroplasty via musculoskeletal modeling may better highlight the role of the anterior cruciate ligament and its stabilizing influence.

Cemented vs Uncemented Femoral Components: A Randomized, Controlled Trial at 10 Years Minimum Follow-Up

BackgroundThe type of total knee arthroplasty (TKA) fixation (cemented or uncemented) is still subject to debate. The aim of this study is to assess the survival rate, clinical outcomes, and radiological results of TKA according to the fixation type. MethodsA total of 130 patients were randomly assigned to either the cement group (cemented femoral and tibial implants) or the hybrid group (cemented tibial implant, uncemented femoral implant). The inclusion criteria were patients between 50 and 90 years old who underwent primary TKA for osteoarthritis between 2004 and 2005 without a history of open knee surgery. Revisions and complications were reported, as well as clinical scores and radiological signs of loosening. ResultsOne hundred eighteen patients had complete data at 10 years of minimum follow-up (59 in each group). The mean age was 72 years old. The mean follow-up was 13 years. The survival rate was 98% at 13 years in both groups (1 aseptic loosening at 2 years in the cement group, 1 septic loosening in the hybrid group). The complication rate in the cement group was 8.5% (n = 5) vs 12.1% (n = 7) in the hybrid group (P = .8). The clinical results were not significantly different. In the cement group, 25% of patients (n = 15) had radiolucent lines at 10 years. In the hybrid group, 33% of patients had bone transparencies, not evolving or symptomatic. ConclusionAt a minimum follow-up of 10 years, there were no significant differences between cemented TKA and hybrid TKA for the survivorship, the complication rate, the clinical scores, or the radiological signs of loosening. Level of EvidenceI.

Comparison of canine stifle kinematic analysis after two types of total knee arthroplasty: A cadaveric study.

Background and Aim:Osteoarthritis is a common consequence of cranial cruciate ligament rupture (CCLR) in the canine stifle. Total knee replacement is a valuable method for managing end-stage osteoarthritis.Materials and Methods:Two new designs of total knee replacement implants were fabricated with information from computed tomography scans. Canine hind limbs of cadavers were tested with a biomechanical testing machine with C-arm fluoroscopy. The four groups tested were as follows: Intact stifles (INTACT), CCLR, total knee arthroplasty (TKA) with a peg on top of the tibial component (TKAP), and TKA with no peg on top of the tibial component (TKAN). Extension, flexion, adduction, abduction, internal rotation, external rotation, cranial translation, caudal translation, and range of motion were measured.Results:The cranial translation of the tibia relative to the femur increased significantly after cutting off the cranial cruciate ligament. After arthroplasty, adduction/abduction and cranial/caudal translation within the TKAN group was increased compared with the intact stifle group. In the TKAP group, only adduction was greater than it was in the intact stifle group.Conclusion:The design of the prosthesis used for the TKAP group was more appropriate for total knee replacement in dogs than the design of the prosthesis for the TKAN group.

Posterior clearance increases the knee extension angle in cruciate retaining type total knee arthroplasty: Intraoperative evaluation using a navigation system

BackgroundPosterior osteophyte of the femur can impinge on the tibia insert in total knee arthroplasty (TKA). Although osteophyte removal [posterior clearance (PC)] improves the flexion angle, its influence on the gaps and extension angle are unclear. This study investigated the effect of PC on the gaps and range of motion (ROM) using a navigation system, as well as PC's relationship with osteophyte size. MethodsTwenty-seven knees that underwent cruciate-retaining (CR)-type TKA were examined. Before and after PC, the ROM, hip-knee-ankle (HKA) angle, and flexion and extension gaps were recorded using a navigation system. Osteophyte size was measured in the lateral view in radiographs, and in the sagittal and axial planes of computed tomography (CT) images. The effects of PC on the gaps and ROM were analysed statistically. ResultsPC caused the extension gap to increase by 0.7 ± 0.9 mm in the medial (p < 0.001), and 0.9 ± 1.5 mm in the lateral compartment (p = 0.006). The extension angle increased by 4.9 ± 1.6°, flexion angle increased by 6.5 ± 5.0°, and HKA decreased by 0.3°. The increase in extension angle by PC was significantly correlated with the preoperative HKA angle (r = 0.594) and with the osteophyte area in radiographs and CT (r = 0.626 to 0.681). ConclusionsThe extension and flexion gaps increased less than 1 mm in the medial and lateral compartments. PC achieving an additional 5° extension angle could promote full extension in severely deformed knees with a large posterior osteophyte. The extension angle increase by PC was correlated with the preoperative HKA angle and osteophyte size.

Consideration of gap adjustment and joint line in PS type total knee arthroplasty using precut method

Consideration of gap adjustment and joint line in PS type total knee arthroplasty using precut method

Computational analysis of customized cruciate retaining total knee arthroplasty restoration of native knee joint biomechanics.

The purpose of this study was to verify if customized prosthesis better preserves the native knee joint kinematics and provides lower contact stress on the polyethylene (PE) insert owing to the wider bone preservation than that of standard off-the-shelf prosthesis in posterior cruciate-retaining type total knee arthroplasty (TKA). Validated finite element (FE) models for were developed to evaluate the knee joint kinematics and contact stress on the PE insert after TKA with customized and standard off-the-shelf (OTS) prostheses as well as in normal healthy knee through FE analysis under dynamic loading conditions. The contact stresses on the customized prosthesis decreased by 18% and 8% under gait cycle loading conditions, and 24% and 9% under deep-knee-bend loading conditions, in the medial and lateral sides of the PE insert, respectively, compared with the standard OTS prosthesis. The anterior-posterior translation and internal-external (IE) rotation in customized TKA were more similar to native knee joint behaviors compared with standard OTS TKA under gait loading conditions. The difference from normal knee kinematics was lower for femoral rollback and IE rotation in customized TKA than in standard OTS TKA in the deep-knee-bend condition. In general, customized prostheses achieve kinematics that are close to those of the native healthy knee joint and have better contact stresses than standard OTS prostheses in gait and deep-knee-bend loading conditions.

In vivo kinematics of gait in posterior-stabilized and bicruciate-stabilized total knee arthroplasties using image-matching techniques.

This study aimed to evaluate the effects of two types of total knee arthroplasty (TKA) designs: posterior-stabilized (PS) and bicruciate-stabilized (BCS) on in vivo kinematics during gait. Continuous X-ray images of the gait were taken using a flat panel detector for 23 PS and BCS TKAs. We analyzed the tibiofemoral implant flexion angle, anteroposterior (AP) translation, axial rotation, and anterior/posterior cam-post contact using image-matching techniques. Double knee actions were demonstrated for the PS and BCS design (35 and 61%, respectively, p = 0.08). The tibiofemoral AP positions were significantly more posterior at peak extension (- 1.7 ± 2.2 and 1.0 ± 2.5mm, respectively, p < 0.01) and anterior at peak flexion (1.3 ± 2.3 and - 0.8 ± 2.8mm, respectively, p = 0.01) for the PS design than for the BCS design, with a significant difference in AP translation (3.0 ± 3.9mm anterior and 1.7 ± 2.8mm posterior, respectively, p < 0.01). Anterior/posterior tibial post contacts were found in 83/4% and 74/30% for the PS and BCS designs, respectively, with a significant difference in posterior contact (p = 0.72/0.04, respectively). The knee flexion pattern, tibiofemoral AP translation, axial rotation, and cam-post contact during gait varied, depending on the type of implant, the PS and BCS designs.

Intraoperative implant gap evaluation by different two tensors for PS-fixed type total knee arthroplasty

Intraoperative implant gap evaluation by different two tensors for PS-fixed type total knee arthroplasty

A Retrospective Comparison of a Medial Pivot and Posterior-Stabilized Total Knee Arthroplasty With Respect to Patient-Reported and Radiographic Outcomes

BackgroundMedial pivot (MP) type total knee arthroplasty (TKA) implants are designed with a highly congruent medial tibiofemoral articulation. Compared with the cam-and-post design of the posterior-stabilized (PS) TKA, the MP-TKA design has been hypothesized to better replicate the natural kinematics of the knee. We compared the MP-TKA and PS-TKA designs, with our primary outcome measures being range of motion (ROM) and patient-reported satisfaction. MethodsThis study was a retrospective comparison between the 2 groups (76 MP-TKA vs 88 PS-TKA). ROM was collected preoperatively, 6 weeks, 6 months, and 1 year postoperatively. The Forgotten Joint Score-12 (FJS-12) scores were collected at a minimum of 1 year postoperatively. ResultsThere was no statistically significant difference in age, gender, or body mass index between the groups. We found a statistical difference in preoperative ROM (MP = 120.3°, PS = 112.8°, P = .002). There was no difference in ΔROM at 6 weeks (MP = −12.36, PS = −3.79, P = .066), 6 months (MP = −4.23, PS = 2.73, P = .182), or 1 year (MP = .17, PS = 3.31, P = .499). Patients who underwent the MP-TKA scored significantly better than the PS-TKA on the FJS-12 score (MP = 59.72, PS = 44.77, P = .007). ConclusionWe found that patients who underwent the MP-TKA scored better on the FJS than those who underwent the PS-TKA; particularly with regard to deep knee flexion and stability of the prosthesis. The MP-TKA design may offer improved patient outcomes because of its highly congruent medial tibiofemoral articulation.

Knee Osteoarthritis: Impact on Quality of Life and Effectiveness of Total Knee Arthroplasty

Background: Arthrosis has a huge impact due to its consequences on suffering and function loss and because it damages the well-being and the physical, emotional and social aspects of Health-Related Quality of Life. Our objective was to assess the influence of Knee Osteoarthritis and Total Knee Arthroplasty on the perception of the patients with regard to their quality of life, before and after the intervention. Method: We carried out a quasi-experimental intervention study with a before and after design in a sample of 125 patients with knee osteoarthritis who were assessed before and after the operation. They all were operated by the same orthopedic surgeon and with the same type of total knee arthroplasty between the year 2008 and 2012. The Health-Related Quality of Life was assessed with the questionnaire SF-36. Results: We have observed that knee osteoarthritis significantly affects all the dimensions of Health-Related Quality of Life before the operation and that all the dimensions included in the SF-36 show a clinical improvement after the intervention with total knee arthroplasty. When the results of the different scales of quality of life from the SF-36 are compared between the patients in our study and the general population in Spain, only Social Functioning is lower, while five dimensions show similar levels and two of them, Role-Emotional and Mental Health, show an improvement. Therefore, we can state that the operation of total knee arthroplasty significantly improves Health-Related Quality of Life in all its dimensions and components, except for Physical Functioning and Role-Physical, although they also improve over time after the operation. Conclusion: Total knee arthroplasty is justified according to the perception of clinical improvement and the improvement of Health-Related Quality of Life reported by the patients.