Tube Pressure Research Articles

Enhancing Bulb Turbine Performance Assessing Air Injection for Vibration Mitigation and Hydrofoil Cavitation

Small hydro technology is playing a crucial role in advancing sustainable, clean energy policies as part of the global hydro development strategy. Its contribution to social and economic development is becoming more prominent, particularly in ensuring electricity access for rural communities and supporting industrial expansion. The main causes of bulb turbine failures under high operating conditions are frequently attributed to variations in pressure in the draft tubes, which are aggravated when a spinning vortex rope is formed under load operation. Different fluid injection techniques, namely compressed air and water jet injection, address these issues and reduce the negative results of cavitation. The investigation covers the flow visualization on the suction side of a single hydrofoil utilizing a cavitation tunnel and a bulb turbine. This study assesses the effectiveness of compressed air injection in reducing vibration generated by cavitation in bulb turbines. Positive results of the experimental studies suggest a decrease in noise and vibration by air injection that prevents oscillations of the vortex rope. This research also considers how the hydrofoil design of bulb runner blades influences flow characteristics. Hence, it provides knowledge on cavitation structures in diverse cavitation numbers. Different studies that compare the original and modified hydrofoil designs reveal remarkable improvements that may be due to changes in the key parameters of the hydrofoil, such as later cavitation initiation and reduced intensity. To obtain the optimal output of a bulb turbine by considering air injection for vibration reduction and hydrofoil design changes to limit the negative effect of cavitation, the Reynolds number and cavitation number are to be defined. This multidisciplinary approach possesses enormous potential to increase the reliability and efficiency of bulb turbines in challenging operating conditions.

Analysis of extremely low water hammer pressures of draft tubes for double units in pumped storage power stations under successive load rejection conditions

With large-scale integration of intermittent energy into power systems, the operating conditions of pumped storage power stations (PSPSs) change frequently, thereby intensifying the risk of load rejections. For multiple units sharing a water conveyance system, when one or more units reject the load, other units also reject the load after a few seconds; this is defined as successive load rejection (SLR). During SLR conditions, pumped storage units produce extreme water hammer pressures, jeopardizing the safe operation of PSPSs. This study reveals the generation mechanism of extremely low draft tube pressure (DTP) during SLR, and clarifies the generating unit and corresponding occurrence moment characteristics of the minimum DTP. The results indicated an extremely low DTP, attributed to the sharp decline in the discharge owing to increased rotational speed in unit's S-shape region and the hydraulic interference owing to the increased discharge of the other unit. When the guide vane closing time (GVCT) was short, the minimum DTP occurred in the subsequent load rejection unit (SLRU) near the first peak of its rotational speed, with the discharge of initial load rejection unit (ILRU) in the rising stage. Conversely, for a large GVCT, the minimum DTP occurred in the ILRU near the second peak of its rotational speed, with SLRU discharge in the rising stage. Finally, engineering measures to improve the extremely low DTP were proposed. Overall, the findings underscore crucial engineering insights for ensuring the safety of PSPSs under extreme conditions.

Assessment of pillar-array electrodes for electrochemical flow reactors using a novel hydrodynamic electrode performance factor

This work introduces and validates a Hydrodynamic Electrode Performance Factor (HEPF) for flow reactors. Traditional approaches to electrode optimization often rely on separated mass transfer and pressure drop metrics, hindering comparisons. We address this issue by combining electrochemical and hydrodynamic parameters through a new mathematical expression. This formulation draws inspiration from established equations in heat transfer and the widely recognized Chilton-Colburn analogy, aiming to develop a quantification method independent of the experimental arrangement. The HEPF is complementary to the well-established volumetric mass transfer coefficient and to Storck’s energetic effectiveness postulates for electrochemical reactors. Additionally, this study validates the proposed equation experimentally and then applies it to evaluate pillar array electrodes using 2D computational fluid dynamics simulations for laminar flow conditions. Both experimental and simulation approaches are used to analyze the hydrodynamic behaviour of the electrodes, utilizing the Forchheimer and Hagen-Poiseuille numbers. Notably, preliminary turbulence effects are observed at Reynolds numbers as low as 50 to 125. Visualization of velocity streamlines revealed distinct wake formation behind the pillars at these low Reynolds numbers. This study also explores how reactor inlets, outlets, and tubing pressure losses affect electrode performance. Results emphasize the importance of considering pressure drop, which is integral to the new hydrodynamic performance factor. Analysis of pillar array electrodes demonstrates that reducing both interpillar distance and pillar radius leads to improved electrochemical performance

Physical mechanism for prolonged test duration in shock tubes

The main challenge in the operation of shock tubes is the very short test time. Hence, this work was carried out to optimize the ratio of driver section to driven section length and to investigate its effect on the test time in a shock tube. Three different cases were tested in this paper for driver to driven tube length ratio of 2, 1, and 0.5. The study was conducted numerically using ANSYS Fluent CFD solver and k-epsilon realizable turbulent model. The shock wave strength and speed were monitored at two different locations downstream the driven tube for diaphragm pressure ratio of 10. The numerical model was verified with experimental measurements in a shock tube apparatus at the College of Engineering, Universiti Tenaga Nasional, Malaysia (UNITEN). From the numerical and experimental data, the primary shock strength was very comparable, while using low pressure ratio of 10. Subsequently, higher pressure ratio of 20 and 30 were implemented and the results were compared to select the longest test time. A driver section to driven section ratio of 2 resulted in a longer test time of approximately of 20 ms. In addition, insignificant reduction in the test duration of about 5 % was observed after increasing the driver tube pressure to 30 kPa. In contrast, higher peak pressure was recorded for pressure ratio of 30 for all three cases.

312. THE VALUE OF DETECTING THE GASTRIC TUBE PRESSURE AFTER MINIMALLY INVASIVE ESOPHAGECTOMY: A PROSPECTIVE, UNCONTROLLED EXPLORATORY STUDY

Abstract Background With the increasing popularity of minimally invasive esophagectomy(MIE), the incidence of postoperative gastric conduit dilation has also shown an increasing trend. The main purpose of this study is to explore the relationship between postoperative tubular gastric dilation and internal gastric tube pressure. Methods In a prospective cohort study from November 2023 to February 2024, 54 patients undergoing MIE were enrolled. Based on postoperative chest X-ray, patients were categorized into acute gastric conduit dilation (Acd) and non-acute dilation (Non-Acd) groups. Gastric tube pressure, including static pressures(SP), peak pressures(PP), and median pressures (MP), was measured postoperatively. Acute gastric dilation was defined as the gastric tube occupying over 40% of the hemithorax on X-ray. We compared the incidence of postoperative complications, surgery-related mortality, readmission rates, and hospital stay durations. Results Of the patients, 19 experienced acute gastric dilation, while 35 did not. The Acd group showed significantly higher SP, PP, and MP (p<0.01). Univariate analysis identified SP, PP, MP, and upper mediastinal pleura reconstruction as risk factors for acute gastric dilation, with SP being a key predictor in multivariate analysis. Patients in the Acd group had longer hospital stays (median 13 days vs. 8 days for Non-Acd). No significant differences were noted in postoperative complications, surgery-related mortality or readmission rates. Conclusion Acute gastric conduit dilation post-MIE is linked to increased gastric tube pressure. Monitoring this pressure is both safe and feasible, offering insights into reducing acute gastric dilation through surgical improvements such as mediastinal pleura reconstruction.

Investigating Taconis oscillations in a U-shaped tube with hydrogen and helium

Taconis oscillations are thermally induced spontaneous excitations of acoustic modes in tubes subjected to large temperature gradients. Cryogenic systems that experience these excitations suffer from increased heat leak and vibrations. This heat leak may also increase boil-off in long-term storage vessels for liquid hydrogen. In this study, U-shaped closed-end tubes with a cold mid-section are experimentally investigated to quantify the oscillation characteristics for hydrogen- and helium-filled systems at various mean pressures, including supercritical hydrogen states. Experimental measurements of the temperature distribution along the tube and acoustic pressure amplitudes and frequencies are taken in constant- and variable-diameter configurations near the onset of oscillations. Thirty different conditions are recorded with mean pressures ranging from 126 kPa to 1127 kPa for helium and 161 kPa to 1816 kPa for hydrogen. A low-amplitude thermoacoustic model is applied to predict the cold temperature and frequency corresponding to the onset of Taconis oscillations. The findings of this study indicate that Taconis oscillations in systems with hydrogen occur at smaller temperature differences than in more traditional helium systems by approximately 10 K. Hydrogen in the constant-diameter configuration excited when cryogenic temperatures reached 35–40 K, whereas helium excited when cryogenic temperatures reached 20–30 K. Special tubing networks, such as wider segments in the warm portion, can drastically elevate the excitation cold temperature resulting in onset temperatures between 50–60 K for both fluids. Taconis oscillations are also found to exist in conditions when liquid hydrogen starts forming in the cold zone of the system, as well as in supercritical states. The presented measurements are useful for designing cryogenic hydrogen storage systems to control these oscillations.

Experimental study on flow and heat transfer of High-Pressure helium flow in compact helical tube heat exchanger in HTGR

In this study, experiments were conducted on helium flow within a compact helical tube heat exchanger. High-temperature helium and deionized cooling water, flowing in opposite directions, were allocated to the shell side and tube side, respectively. The Reynolds number of helium ranged from 3 × 103 to 1.6 × 104 under an operational pressure of 2.1 MPa. Measurements were taken for helium temperature, tube outer-surface temperature distribution, pressure, and mass flow rate to illustrate the flow and heat transfer characteristics. Sensitivity analysis of thermal–hydraulic parameters, including heat transfer power and efficiency under various operational conditions, was performed. The convective heat transfer coefficient and pressure drop were calculated. The transition point (Re = 9000) between laminar and turbulent flow of helium on the shell side was identified, and empirical correlations for the Nusselt number and friction coefficient were proposed. The experimental results indicate that the heat transfer performance of helium in the compact helical tube heat exchanger exceeds that of water in large-scale helical tube heat exchanger by approximately 20.75 % under fully developed turbulence, while the flow resistance characteristics remain essentially consistent.

Tube cross-section flatness optimization to enhance the cooling performance of nanofluid-based photovoltaic thermal systems combined with nano-enhanced phase change material

Photovoltaic (PV) systems have emerged as a crucial technology in transitioning to sustainable energy. Despite their growing prominence, PV panels face challenges related to temperature-induced that can lead to reduced energy output. By considering this, the utilization of cooling systems is useful. In the quest to design the active cooling system for PV panels, a key challenge remains in optimizing tube cross-section configurations. In this study, a validated CFD simulation investigates the impact of the tube cross-section flatness (tube flattening) on the cooling performance of the nanofluid-based photovoltaic thermal system combined with nano-enhanced Phase Change Material (PCM). Evaluation parameters for cooling performance are PV surface temperature (T_s), PCM liquid Fraction (LF), tube pressure drop (ΔP), and the PV temperature uniformity (ΔT). Aluminum Oxide (Al2O3) and Silver (Ag) nanoparticles are used in different concentrations (0 %, 1 %, 5 %, 10 %). Also, using the Response Surface Method (RSM), a multi-objective optimization determines the optimal tube flattening percentage for achieving the best cooling performance. The ideal state entails minimizing T_s, maximizing LF, minimizing ΔP, and minimizing ΔT. The findings indicate that increasing tube flattening leads to a decrease in T_s, a decrease in LF, an increase in ΔP, and a reduction in ΔT. Reducing the T_s and ΔT is a favorable effect but increasing the ΔP and reducing the LF is unfavorable to the system's cooling performance. After evaluating different parameters in the optimized scenarios, the most optimal mode is determined when the system uses Ag nanofluid in 10 % concentration, PCM without nanoparticles, and tube with 44 % flattening. In this scenario T_s, LF, ΔP, and ΔT are respectively 54.04 °C, 37.7 %, 117.67 Pa, and 34.74 °C.

Specialized nursing intervention on critically ill patient in the prevention of intubation-associated pneumonia: an integrative literature review.

Healthcare-associated infections are adverse events that affect people in critical condition, especially when hospitalized in an intensive care unit. The most prevalent is intubation-associated pneumonia (IAP), a nursing-care-sensitive area. This review aims to identify and analyze nursing interventions for preventing IAP. An integrative literature review was done using the Medline, CINAHL, Scopus and PubMed databases. After checking the eligibility of the studies and using Rayyan software, ten final documents were obtained for extraction and analysis. The results obtained suggest that the nursing interventions identified for the prevention of IAP are elevating the headboard to 30º; washing the teeth, mouth and mucous membranes with a toothbrush and then instilling chlorohexidine 0.12%-0.2% every 8/8 hr; monitoring the cuff pressure of the endotracheal tube (ETT) between 20-30 mm Hg; daily assessment of the need for sedation and ventilatory weaning and the use of ETT with drainage of subglottic secretions. The multimodal nursing interventions identified enable health gains to be made in preventing or reducing IAP. This area is sensitive to nursing care, positively impacting the patient, family, and organizations. Future research is suggested into the effectiveness of chlorohexidine compared to other oral hygiene products, as well as studies into the mortality rate associated with IAP, with and without ETT for subglottic aspiration.

Sustainable Ecological Non-Sintered Ceramsite (SENC) with Alkali Activators: Performance Regulation and Microstructure

The development of novel materials made from waste is one of the main measures to achieve sustainable materials development. In this study, ash of mushroom and corn straw (MCA) and furnace slag (FS) were used as raw materials to prepare alkali-activated biomass ash-slag material (AABS) and sustainable ecological non-sintered ceramsite (SENC). In this paper, the effects of quicklime powder (QL), NaOH, and sodium silicate solution (SS) on AABS were analyzed using single factor and orthogonal tests, and the preferred ratio of the composite alkali activator configuration was established. SENC was prepared based on the composite alkali activator, and the microstructure and phase composition of SENC were explored using XRD and SEM–EDS. The results showed that 3 wt% QL enhanced the early age compressive strength of AABS. The composite alkali activator was best configured when the additions of QL, NaOH, and SS were 3%, 2%, and 15%, respectively. At this configuration, the 28 d compressive strength of AABS was 47.4 MPa, and most of the internal pores were less than 0.4 μm; the 28 d numerical tube pressure of the SENC reached 12.2 MPa with a softening coefficient of 0.96. According to the results of XRD and SEM–EDS, SENC contained various hydration products such as C-A-S-H, calcium hemicarboaluminate, hydrotalcite, portlandite, and vaterite. The largest proportion of hydration products was C-A-S-H, which contributed to the pore refinement and structural densification. SENC has the potential to be used as coarse aggregate in sustainable lightweight concrete.

Tearing behaviors of coated fabric inflatable tube

In this paper, the tearing properties of the inflatable tube with coated fabrics were investigated. Firstly, uniaxial tensile, shear, and single-edge notched tests were conducted to obtain the material properties. Then, considering the modified stress field model and bulge effect, a theoretical calculation formula for the critical tearing pressure was proposed. Next, based on finite element method, the macroscopic orthotropic elastic continuum models of the single-edge notched test and pressurized cylinder test were established. In numerical model, when the average stress in the critical distance at the crack tip reached the tensile strength, the tearing began. Then, the critical distance was determined when the critical tearing load of the numerical model was closest to the single-edge notched tests’ result. Based on the numerical simulation of pressurized cylinder test, the critical tearing pressure of inflatable tube was obtained. Finally, the pressurized cylinder test and puncturing test were designed and conducted. In the pressurized cylinder test, when the first yarn at the crack tip broke, the critical tearing pressure and configuration around the crack were obtained. Moreover, the correctness of the critical tearing pressure in theoretical calculation formula and numerical model was verified through pressurized cylinder test. In puncturing test of inflatable tube, there were obvious crack expansion and explosion. Based on the theoretical calculation formula for the critical tearing pressure, the predicted results were consistent with puncturing test's results.

Characteristics of Center-blast Tube with V-grooves During Blasting

The prediction of fracture time and crack development of metal shell under the impact load is a very significant research direction in engineering. In this paper, a coupling method is used to solve the dynamic expansion fracture process of center-blast tube with V-grooves under the pressure. A one-dimensional two-fluid model was utilized to govern the transient combustion. The nonlinear mechanical behaviors were predicted based on the finite element software ABAQUS, and the pressure and the structure were coupled by applying a user subroutine interface VUAMP in ABAQUS. The coupling approach was validated by comparing the predicted results with experimental results. Based on the validated approach, the characteristics of expansion fracture and the process of crack propagation on the center-blast tube with V-grooves were studied, and the effect grooves depth were analyzed. The results show that the crack propagation on tube can be divided into two stages that stable propagation stage and unstable propagation stage. The burst pressure of the center-blast tube with V-grooves decreases with the increase of crack depth, and the burst pressure decreases by about 7MPa with every depth increase of 0.25mm.

Study on the effect of geometry and material property on collapse pressure of a helical steam generator tube under external pressure

In this paper, a numerical study was conducted to analyze the effect of the geometry (tube thickness, ovality, and helical diameter) and material properties of once through steam generator tubes subjected to external pressure on collapse pressure. The outer diameter of the steam generator tube was fixed at 17 mm, and the tube thickness was changed to 2.5 mm, 2.29 mm, and 1.27 mm. Ovality was considered for three cases of 0 %, 4 %, and 8 %, and three cases for helical diameter were considered: 577 mm, 937 mm, and 1297 mm. As material properties, elastic perfectly plastic property that ignores plastic hardening and real material property that reflect plastic hardening were considered. At the helical diameter (Dm/do ≥ 34) considered in this paper, the effect of collapse pressure due to helical bending did not appear on ovalities and both material properties. On the other hand, the wall thickness affected the collapse pressures according to the material properties when ovality occurred (>0 %). This is explained because the collapse mechanism varies depending on the thickness.

Simple Design Method for Ceramic Tube Pressure Housings

Simple Design Method for Ceramic Tube Pressure Housings

Numerical investigation of hydrogen ignition induced by unsteady flow phenomena

The purpose of the present study is to evaluate the possibility of using a gas dynamic heater as an igniter of the combustible gas mixtures. The impacts of some operating and geometrical parameters on average temperature of the gas dynamic heater are investigated by numerical simulation of axisymmetric turbulent flow in the resonance tube. The operating gas of the heater is air which is completely decoupled from the ignition chamber. The combustible mixtures under consideration is stoichiometric hydrogen-oxygen at atmospheric pressure, in which the ignition is studied solving the governing equations for one dimensional reacting flow using detailed chemistry. The finite volume method is used in the presently developed flow solver for numerical simulations. The results show that despite highly fluctuating temperature of the end wall of the resonance tube as a hot surface, it can provide proper condition for gas mixture ignition in the chamber, by adjusting an inlet pressure and geometry of the gas dynamic heater. The end wall average temperature depends on the nozzle inlet pressure and convergence angle of the resonance tube, and the results demonstrate that the characteristics of temperature time history of repeating cycles are so effective on ignition process.

Experimental and numerical study of combustion in pipe cutting operations with hydrogen-blending gas

This study investigated the flame combustion of gas-containing pipe cutting operations by combining experimental and numerical simulation techniques. Based on the empirical flame length formula and experimental and numerical simulation flame length data, a flame length formula for gas outlet with large aspect ratio was proposed. In the experimental phase, cutting experiments were conducted with cutting slit lengths of 1–11 cm for pipe pressures of 10–550 Pa and hydrogen doping ratios of 0%, 10%, and 20%. The flame lengths were then measured. A hydrogen-doped natural gas combustion model based on the vortex dissipation conceptual model and Grimech-3.0 mechanism was established to simulate the experimental conditions. The flame lengths derived from the numerical simulation were in good agreement with the experimentally measured flame lengths, with an average error of 7.02%. This indicates that the reliability of the numerical model can be verified. The effects of hydrogen doping ratio, tube pressure, and cutting slit length on flame length and thermal radiation range were investigated using the control variable method. The results demonstrated that hydrogen doping reduced flame length and flame length away from the flame. Furthermore, an increase in pipe pressure and single cut length also resulted in an increase in flame length. It was observed that under normal operating conditions, a safe intensity of thermal radiation could be maintained within the operating distance when the operator wore protective clothing.

Effect of varying cuff sizes with identical inner diameter on endotracheal intubation in critically ill adults: A sealed tracheal controlled trial.

The present study aims to determine the impact of different cuff diameters on the cuff pressure of endotracheal tubes (ETTs) when the trachea is adequately sealed. In the present single-center clinical trial, adult patients who underwent cardiothoracic surgery were assigned to use ETTs from 2 brands (GME and GZW). The primary endpoint comprised of the following: cuff diameter, inner diameter of the ETT, manufacturer, and the number of subjects with tracheal leakage when the cuff pressure was 30 cm H2O. A total of 298 patients were assigned into 2 groups, based on the 2 distinct brands of ETTs: experimental group (n = 122, GME brand) and control group (n = 176, GZW brand). There were no significant differences in baseline characteristics. However, the cuff diameter was significantly smaller in the control group, when compared to the experimental group (P = .001), and the incidence of tracheal leakage was significantly higher in the control group (P = .001). Furthermore, the GME brand ETT had a significantly larger cuff diameter, when compared to the GZW brand ETT. The cuff size would mismatch the tracheal area in clinical practice. Therefore, chest computed tomography is recommended to routinely evaluate the tracheal cross-sectional area during anesthesia, in order to ensure the appropriate cuff size selection.

Forced convective rate and pressure drop through a packed annulus: a numerical simulation

Porous materials are used in engineering and industry due to their heat transmission qualities. This study examined forced convection flow through an annular tube packed with sphere balls of various materials and sizes using numerical analysis. The sphere balls were permeable. Ceramic, plastic, and steel with spherical diameters of 3, 5, and 6 and porosity of 0.4 were tested for heat dissipated and fluid flow. Also, test the impact of steel balls of diameter 6mm with 0.6 and 0.8 porosity. The numerical simulation results are used to analyze the forced convection and fluid flow parameters of a three-dimensional annular tube with continuous heat flux in the Reynold number range (5000-14000). Steel balls had an 80% higher heat transfer coefficient than annular tubes without porous mediums. The simulation showed that inserting the porous media increased annular tube pressure loss. The maximum heat transfer coefficient improved by about 80% when the spherical diameter is 3 mm. Also, the result illustrated the heat transfer coefficient of steel balls Increased by about 79%, 69%, and 49%, with 0.4, 0.6, and 0.8 respectively

The influence of the S shaped characteristics of high head pump-turbine on the minimum pressure of draft tube

Abstract The S shaped characteristics of pump-turbines have an important impact on the minimum pressure of draft tube. The quality of the S shaped characteristics is one of the key indicators to determine the success of model runner development, and this indicator is particularly important for ultra-high head pump-turbines. In order to delve deeper into the inherent relationship between the S-shaped characteristics of the runner and the optimization design and minimum pressure of draft tube, this article first defines a method for fixed-point quantitative analysis of the S shaped characteristic curve. Then, different experimental characteristic curves obtained from multiple optimized designs of the runner are used to calculate the hydraulic transition process. At the same time, the S shaped curve is quantitatively analyzed, and the relationship between the three is explored through continuous analysis. The results show that the bending degree of the equal opening lines in the middle at the S shape characteristics curves has the greatest influence on the minimum pressure at the draft tube inlet. The greater the ratio of unit flow difference to unit speed difference in the S shape characteristics curves of the equal opening line, the greater the runaway unit flow on the same equal opening line, the more favorable it is to increase the minimum pressure at the inlet of the draft tube. The optimal design of blade type and guide vane airfoil can improve the minimum pressure value of draft tube to a certain extent. The conclusions obtained in this paper can be used for reference in the research and development design of high head pump-turbine runner and the optimization calculation of transition.

Analysis of impact pressure, rock-breaking effect, and ground vibration induced by the disposable CO2 fracturing tube

The technology of expansion fracturing with liquid CO2 (EFLCO2) has attracted increasing attention due to reduced vibration and damage. The disposable fracturing tube has been developed and is gradually replacing the Cardox tube. However, there is a lack of impact pressure testing of disposable tubes under real working conditions, selection of gas explosion design parameters, and systematic analysis of blasting vibration. This limitation has constrained the widespread application of disposable fracturing tubes in engineering. A joint monitoring of the pressure-time curves in the disposable tubes and boreholes was conducted. The rock-breaking effect of varying hole spacing parameters in the EFLCO2 design was analyzed, and a systematic study was carried out on the vibration peak value, frequency, and energy characteristics. The results show that (1) the pressure distribution characteristics, stress peak value, and duration in the disposable tubes are different from those of Cardox tubes, which show multi-peak distribution, low-pressure peak value, and short duration. The correlation between the pressure in the disposable tube, filling pressure, and liquid CO2 weight is established, and a theoretical calculation method for the borehole wall pressure is proposed; (2) The hole spacing in rocks of different hardness is suggested; and (3) At the same scale distance, the peak particle velocity (PPV) caused by EFLCO2 (PPVCO2) is significantly smaller than that caused by blasting (PPVexplosive). The ratio of PPVexplosive to PPVCO2 is a power function related to scale distance, and a distance-related zonality exist in this relationship. The frequency composition of the vibration signal caused by EFLCO2 is relatively simple with a narrow frequency band. Its PPV and energy are mainly concentrated in the low-frequency band. This research contributes to the optimization of disposable fracturing tubes, gas explosion design, and vibration hazard control.