Trioctylphosphine Oxide Research Articles

A novel ternary hydrophobic deep eutectic solvent over a wide pH range for lithium recovery

Owing to the crucial role of lithium (Li) in green technology and energy storage, the global demand for Li is constantly increasing. This article provides a new strategy for recovering Li using ternary hydrophobic deep eutectic solvent (HDES). The novel HDES was composed of 2-thiophenyltrifluoroacetone (HTTA), trioctylphosphine oxide (TOPO), and N,N-diethyldecanamide (DDA), and exhibited high efficiency and selectivity for extracting Li from aqueous solutions. This study systematically evaluated the effect of the initial aqueous pH on the Li extraction efficiency, revealing the stable performance of HDES in the pH range 3–13. Compared to the highly alkaline environment required for Li extraction, the pH characteristics of the HDES provide a wider range of applications and a more environmentally friendly alternative. The HDES exhibited rapid extraction kinetics, achieving equilibrium within 10 min and maintaining phase stability without emulsification. The main mechanism of selective Li extraction is the electrostatic interaction between Li(I) and TTA. The interactions between Li(I) and both TOPO and DDA were confirmed by Fourier transform infrared (FT-IR) spectroscopy, thereby improving the selectivity and extraction efficiency. The countercurrent extraction process demonstrated an impressive Li extraction rate of 98.704 % and a Li(I)/Na(I) separation factor of 10643.14 with industrial Li2CO3 mother liquor, highlighting the application potential of the ternary HDES. The excellent performance of the HDES over a wide pH range provides more opportunities for its application, and its high efficiency, selectivity, and environmental characteristics may promote Li recovery.

Extraction of mandelic acid with tri-octyl-phosphine oxide (TOPO) in different solvents: Equilibrium and neural network analysis

Mandelic acid is an important carboxylic acid used in pharmaceutical industries. It is also important to use it as a purified form. In this study, selective extraction of mandelic acid was done by tri-octyl-phosphine oxide (TOPO) diluted in different solvents such as methyl isobutyl ketone, 1-octanol, octyl acetate, dimethyl phthalate, 2-octanone, cyclohexane and toluene. The high selectivity of mandelic acid from aqueous solution was supported by thermodynamic parameters (loading factor, distribution coefficient, and extraction efficiency). The obtained values for each solvent were applied to the Neural Network Analysis to predict phase equilibrium behaviour in ternary systems. The results showed the highest mandelic acid extraction efficiency (93.65 %) and distribution coefficient (14.74) were attained with the organic phase mixture prepared with MIBK and TOPO. Also, it was found that extraction efficiencies increased with increasing TOPO amount in the medium for all studied solvents.

Fractionation of phenolic aldehydes by liquid–liquid extraction and polymer resin adsorption

ABSTRACT The extraction and adsorption characteristics of three phenolic aldehydes with high physicochemical similarity in lignocellulosic biomass hydrolyzate, which are fermentation inhibitors, were investigated. The extraction process considered both physical extraction with two organic solvents and reactive extraction with five basic extractants. In physical extraction, n-hexane was found to be the most suitable organic solvent for selectively separating 4-hydroxybenzaldehyde from the three phenolic aldehydes, and in reactive extraction, trioctylphosphine oxide was identified as the most suitable basic extractant for the selective separation of syringaldehyde. In the adsorption process, various neutral polymer resins and anion-exchange polymer resins were employed. Among them, the neutral polymer resin XAD16 was found to be the most suitable for selectively separating 4-hydroxybenzaldehyde. To efficiently separate and concentrate the three phenolic aldehydes with equal mass percentages, a proposed five-step fractionation process included the aforementioned extraction and adsorption techniques. By implementing n-hexane-based physical extraction in step 4 and NaOH solution-based back-extraction in step 5 of the fractionation process, the purities of 4-hydroxybenzaldehyde, vanillin, and syringaldehyde in the final solution increased from their initial 33.3% each to 67.6%, 69.8%, and 76.4%, respectively, at a volume ratio of the aqueous phase to the organic phase of 1:15.

COSMO-RS screening of organic mixtures for membrane extraction of aromatic amines: TOPO-based mixtures as promising solvents

Aromatic amines are crucial in pharmaceuticals, but their synthesis is challenging due to unfavorable reaction equilibria and the use of costly, environmentally unfriendly methods. This study presents a membrane extraction (ME) process for in situ product removal (ISPR) of aromatic amines. Using a supported liquid membrane (SLM), -methylbenzylamine (MBA) and 1-methyl-3-phenylpropylamine (MPPA) were separated from isopropyl amine (IPA). COSMO-RS was employed to screen over 200 organic mixtures, identifying twelve mixtures based on trioctylphosphine oxide (TOPO), lidocaine, and menthol as solvent candidates, due to their hydrophobicity. These mixtures were analysed for critical solvent properties including density, viscosity, hydrophobicity, and hydrogen bonding interactions. ME tests showed TOPO-thymol had the highest solvent residual and selectivity. Moreover, TOPO-thymol demonstrated solute fluxes of 9.0±3.0 g/(m2 h) for MBA, 16.5±5.4 g/(m2 h) for MPPA, and 0.7±0.3 g/(m2 h) for IPA, with selectivity values of 12.4±0.8 for MBA/IPA and 22.8±1.4 for MPPA/IPA. Compared to undecane, which had lower selectivity values of 6.9±0.8 for MBA/IPA and 10.1±1.3 for MPPA/IPA, TOPO-thymol showed superior selectivity, indicating its promise as an extractant for ME applications.

Recovery of lithium from oxalic acid leachate produced from black mass of spent electric vehicle Li-ion batteries

Lithium (Li) demand is surging due to the adaptation of Lithium-ion batteries (LIBs) in electric vehicles (EV). To ease the supply from virgin sources and meet new legislative recycling targets it's imperative to secure supply from secondary sources. Recently oxalic acid leaching has been reported for early-stage recovery of Li from black mass (BM) of spent EV LIBs. Such processes often face challenges in electrodes separation, thermal treatment of cathode material, and leachate up-concentration. Herein, the synergistic application of benzoyltrifluoroacetone (HBTA) and trioctylphosphine oxide (TOPO) to extract Li from oxalate streams of an industrial BM has been demonstrated for the first time. Under optimum conditions, ∼92 % Li was extracted from the leachate in 6mins, aqueous/organic (A/O) phase ratio 1, and pH 11. McCabe Thiele diagram indicated two counter-current stages for the complete extraction of Li at A/O 1. The slope analysis method indicated equal moles of HBTA required to extract Li and FT-IR spectroscopy confirmed the synergism of the extractants. The organic phase was scrubbed with Li salt and stripped with hydrochloric acid (HCl) resulting in a concentrated (Li ∼4 mol/L) solution precipitated as lithium carbonate (>99 % pure). The transition metals during oxalic acid leaching were reduced and precipitated as respective oxalates due to low solubility. They were successfully recovered using a second leaching step with HCl. The excess acid was recovered as oxalic acid by cooling crystallization, not reported earlier for BM recycling streams, facilitating a closed-loop process. The developed flowsheet significantly advances the early-stage Li recovery processes from BM.

A novel strategy for sequential separation of Th(IV) from highly acidic wastewater based on solid phase extraction

The potential applications and advantages of thorium(Th) in the development of the nuclear industry make the effective separation of Th(IV) crucial for depleted fuel management and environmental safety. However, selectively capturing of Th(IV) from high-concentration nitric acid remains a challenging task. In this work, a novel solid-phase extraction resin (TOPO/XAD-7) was successfully synthesized by vacuum impregnation of trioctylphosphine oxide (TOPO) into an acrylic-based polymer (XAD-7 resin). It exhibited excellent adsorption abilities for Th(IV), including wide highly concentration acid tolerance (0.01–6 mol L−1 HNO3), high adsorption capacity of 59.79 mg g−1, fast adsorption kinetic (< 60 min) and super elevated selectivity. The adsorption mechanism of the resin involves neutral chelation extraction, with the PO group being the main adsorption binding site. Additionally, the resin was demonstrated good reusability and stability under extreme conditions (high acidity, high temperature and high radiation). Furthermore, dynamic column experiments conducted using an automated separation system validated the practical application of TOPO/XAD-7 resin for the separation of Th(IV) and U(VI)/Th(IV) in wastewater, achieving high element recovery (> 99.5%) and a high U(VI) decontamination factor (3.5 × 105). This work confirms the excellent potential of TOPO/XAD-7 resin for the separation and enrichment of Th(IV) in nuclear wastewater.

Concentration-Dependent Layer-Stacking and the Influence on Phase-Conversion in Colloidally Synthesized WSe2 Nanocrystals.

We report a synthesis of WSe2 nanocrystals in which the number of layers is controlled by varying the precursor concentration. By altering the ratios and concentrations of W(CO)6 and Ph2Se2 in trioctylphosphine oxide, we show that high [Se] and large Se/W ratios lead to an increased number of layers per nanocrystal. As the number of layers per nanocrystal is increased, the nanocrystal ensembles show less phase-conversion from the metastable 2M phase to the thermodynamically favored 2H phase. Density functional theory calculations indicate that the interlayer binding energy increases with the number of layers, indicating that the stronger interlayer interactions in multilayered nanocrystals may increase the energy barrier to phase-conversion. The results presented herein provide insights for directing phase-conversion in solution-phase syntheses of transition metal dichalcogenides.

Membrane transport of rare earth metal ions N, N’-bisdioctylphosphorylmethyl-1,4-diaminobutane by the active transport mechanism

The method of membrane extraction for rare earth elements (REE) using the carrier N, N’-bisdioctylphosphorylmethyl-1,4-diaminobutane (DPDA-8) ions, leveraging an active transport mechanism, has been optimized. The distribution of DPDA-8 within the membrane pores was confirmed using scanning electron microscopy (SEM). Both light and heavy REE extractions from a simulated solution using DPDA-8 and trioctylphosphine oxide (TOPO) in 1,2-dichlorobenzene were explored. The influence of feed solution pH, carrier and anion concentration, supported liquid membrane (SLM) type and stability, and cell temperature, among other parameters, were meticulously examined. The results indicate a decrease in permeability with a decrease in feed solution pH attributed to competitive acid transport through the membrane. Additionally, the formation of H-complexes between carriers and perchloric or phosphoric acids was investigated using Fourier Transform Infrared (FTIR) spectroscopy and X-ray diffraction (XRD) techniques. Changes in the stretching bands of amino and phosphine oxide groups in DPDA-8 were monitored and characterized. XRD analysis of the crystal structures of salts DPDA-6·ClO4 and DPDA-12·H2PO4 revealed a two-dimensional layered supramolecular organization with varying anion positions relative to hydrophobic fragments. The DPDA-8 carrier demonstrated significantly higher permeability values compared to TOPO, with differences in permeability exceeding twofold for certain metals. FTIR spectroscopy identified the main coordination centers of DPDA-8 during the liquid–liquid extraction of specific REEs.

Continuous Liquid-Liquid Extraction of Medium-Chain Fatty Acids from Fermentation Broth Using Hollow-Fiber Membranes.

Medium-chain fatty acids (MCFAs; carbon-lengths: C6-C12) are high-value platform chemicals that serve a variety of industrial applications, including green antimicrobials, food ingredients, animal feed additives, cosmetics, fragrances, pharmaceuticals, and structured lipids. Currently, most MCFAs are produced from palm and coconut oil originating from Southeast Asia and South America. The conventional approach to harvesting palm and coconut fruits causes considerable ecological damage in these regions. Therefore, researchers are developing biological approaches (e.g., precision and open-culture fermentations) to generate MCFAs more sustainably using low-value substrates (e.g., methanol, ethanol, lactate) or organic wastes as feedstock. Microbial chain-elongation (CE) is a rapidly maturing open-culture fermentation platform that converts short-chain fatty acids (SCFAs; carbon lengths: C1-C5) into a subset of these MCFAs at industrially relevant rates. However, continuous in situ extraction of MCFA products is necessary not only to avoid product inhibition but also to facilitate the recovery of MCFAs in a pure and usable form.Liquid-liquid extraction (LLE) using hollow-fiber membranes and targeted extractant mixtures has proven a robust approach to selectively extract MCFA products from fermentation broths containing SCFAs. Here, the application of LLE for continuous MCFA removal is demonstrated using CE as the reference fermentation system and 3% (w/v) trioctylphosphine oxide in mineral oil as the extractant system. Fatty acids ranging from valeric acid (C5) to caprylic acid (C8) are selectively removed from SCFA-containing broths and concentrated to high titers in a semi-batch alkaline stripping solution for downstream processing.

Benzyl viologen dichloride as a novel ligand for CdSe CQDs in hybrid QDs/organic photodiodes

The use of colloidal quantum dots (CQDs) in advanced optoelectronic devices requires the substitution of bulky long ligands with short organic ligands. The search for a short-ligand that can create stable quantum solids without compromising the confinement of the CQDs is of paramount importance.Within this context, we present a novel surface passivation ligand, benzyl viologene dichloride (BVD-Cl), as a replacement for the conventional trioctylphosphine oxide (TOPO) capping of CdSe CQDs. BVD-Cl enables the creation of a CdSe quantum solid while retaining quantum confinement. To demonstrate the efficacy of this ligand-exchange process, we utilised Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectrometry (EDX), high-resolution transmission electron microscopy (HR-TEM), and X-ray photoemission spectroscopy (XPS). We then implanted the new BVD-Cl:CdSe quantum film as the main inorganic QDs layer into a hybrid photodiode combined with poly 3-hexylthiophene (P3HT) as the organic layer. The photodiode demonstrated high sensitivity to light stimuli and rectifying behaviour, with a responsivity of 70 mA/W at 550 nm. Our observations imply that using BVD-Cl as a surface passivation ligand for CQDs has significant implications for the development of advanced optoelectronic devices.

TOPO-decanoic acid based DES – Structural insights using DFT, physico-chemical investigations and extraction efficiency of DES diluted with chloroform

Deep eutectic solvents (DESs) are recently regarded as evolving candidates in the field of separation science in order to achieve sustainability. In the present work, hydrophobic TOPO-Decanoic acid DES has been synthesized and scrutinized by FTIR and 1HNMR studies. The structures of TOPO (Tri-octyl phosphine oxide), decanoic acid, chloroform, DES and DES + chloroform have been optimized employing B3LYP functional using DFT-D3 of Grimme’s method. The HOMO-LUMO (Eg) energy gap, bond lengths, mulliken charges,dipole moment and interaction energy has been evaluated using DFT. The geometry optimization provides the bond parameters which explain about the existence of non-bonded interactions. DES and DES + chloroform show more reactiveness as compared to its constituents evident from the chemical potential value. Physico-chemical properties such as density, volumetric (V), dielectric constant (ε), refractive index (nD) and ultrasonic velocity (U) of the hydrophobic TOPO-Decanoic acid DES diluted with polar cosolvent chloroform have been determined over a wide range of mole fraction of DES at 298.15 K. The excess properties such as VE, εE, nDE and UE have been calculated to predict the type of inter-molecular interaction existing within the components of the DES diluted chloroform mixture. Different mixing rules have been used to estimate properties such as dielectric permittivity, refractive index and ultrasonic velocity. Various acoustic parameters such as Z, βs, and (Lf)mix of binary mixtures are evaluated to predict about the presence of inter molecular interactions within the mixture components. The prepared hydrophobic eutectic mixture in chloroform has been further used for extraction of Y (III) and Eu (III). The solvent extraction of Eu (III) showed better performance as compared to that of Y (III).

Controlling the Phase Distribution of Single Bromide Quasi-2-Dimensional Perovskite Crystals via Solvent Engineering for Pure-Blue Light-Emitting Diodes.

To achieve pure-blue emission (460-470 nm), we manipulate the crystallization process of the quasi-2D perovskite, (PBA)2Csn-1PbnBr3n+1, prepared by a solution process. The strategy involves controlling the distribution of "n" phases with different bandgaps, solely utilizing changes in the precursor's supersaturation to ensure that the desired emission aligns with the smallest bandgap. Adjustments in photoluminescence (PL) wavelength are made by changing the solute concentration and solvent polarity, as these factors heavily influence the diffusion of cations, a crucial determinant for the value of "n". Subsequently, we enhance the PL quantum yield from 31 to 51% at 461 nm using trioctylphosphine oxide (TOPO) as an additive of antisolvent, which passivates halide vacancy and promotes orderly crystal growth, leading to faster carrier transfer between phases. With these strategies, we successfully demonstrate pure-blue LEDs with a turn-on voltage of 3.3 V and an external quantum efficiency of 5.5% at an emission peak of 470 nm with a full-width at half-maximum of 31 nm.

Sustainable and efficient recovery of lithium from rubidium raffinate via solvent extraction

In recent years, with the increasing prevalence of rechargeable lithium-ion batteries in the burgeoning markets of electric vehicles and portable electronic devices, the consumption of lithium batteries has significantly surged. Hence, the efficient development and utilization of associated lithium resources bear paramount significance. This study aims to recover lithium from rubidium raffinate via solvent extraction. A systematic investigation was conducted to examine the effects of various parameters such as organic phase concentration, contact time, and phase ratio (O/A) during the separation process. The results indicated that the organic phase composed of 0.1 mol/L 4,4,4-Trifluoro-1-phenyl-1,3-butanedione (HBTA) and 0.1 mol/L Trioctylphosphine oxide (TOPO) could efficiently extract lithium from the rubidium raffinate. The optimal conditions were observed at a temperature of 20℃, O/A=1, and a contact time of 5 min. After three-stage countercurrent extraction, a lithium extraction rate of 99.24 % could be achieved, with over 95 % of the sodium easily scrubbed by 0.1 mol/L HCl at an O/A=10. With the use of 3 mol/L HCl, stripping efficiency exceeding 99 % could be attained at an O/A=10, consequently a successful preparation of battery-grade lithium carbonate product was achieved. Regeneration experiments confirmed the organic phase's excellent reproducibility efficiency. Slope analysis and density function theory (DFT) simulations indicated that optimal lithium extraction is achieved when HBTA and TOPO are at equal molar concentrations. The proposed process is expected to provide a green and sustainable route for the recovery of associated lithium resources.

Lead Bromide Complex in Tri-n-Octylphosphine Oxide Matrix with Bright Photoluminance and Exceptional Thermoplasticity.

Metal halide materials have recently drawn increasing research interest for their excellent opto-electronic properties and structural diversity, but their resulting rigid structures render them brittle and poor formability during manufacturing. Here we demonstrate a thermoplastic luminant hybrid lead halide solid by integrating lead bromide complex into tri-n-octylphosphine oxide (TOPO) matrix. The construction of the hybrid materials can be achieved by a simple dissolution process, in which TOPO molecules act as the solvents and ligands to yield the monodispersed clusters. The combination of these functional units enables the near-room-temperature melt-processing of the materials into targeted geometry by simple molding or printing techniques, which offer possibilities for fluorescent writing inks with outstanding self-healing capacity to physical damage. The intermarriage between metal halide clusters with functional molecules expands the range of practical applications for hybrid metal halide materials.

Exploring the role of neutral ligands in modulating the photoluminescence of samarium complexes with 1,1,1,5,5,5-hexafluoro-2,4-pentanedione.

Four eight-coordinated luminescent samarium complexes of type [Sm(hfpd)3L2] and [Sm(hfpd)3L'] [where hfpd = 1,1,1,5,5,5-Hexafluoro-2,4-pentanedione L = tri-octyl-phosphine oxide (TOPO) and L' = 1,10-phenanthroline (phen), neocuproine (neoc) and bathocuproine (bathoc) were synthesized via a stoichiometrically controlled approach. This allows for precise control over the stoichiometry of the complexes, leading to reproducible properties. This investigation focuses on understanding the impact of secondary ligands on the luminescent properties of these complexes. Infrared (IR) spectra provided information about the molecular structures, whereas 1H and 13C nuclear magnetic resonance (NMR) spectra confirmed these structural details along with the coordination of ligands to trivalent Sm ion. The UV-vis spectra revealed the molar absorption coefficient and absorption bands associated with the hfpd ligand and photoluminescence (PL) spectroscopy demonstrated intense orange-red emission (648 nm relative to 4G5/2 → 6H9/2) from the complexes. The Commission Internationale de l'Éclairage (CIE) triangles indicated that the complexes emitted warm orange red light with color coordinates (x, y) ranging from (0.62, 0.36) to (0.40, 0.27). The investigation of the band gap as well as color parameters confirms the utility of these complexes in displays and LEDs.

The highly selective green colorimetric detection of yttrium ions in biological and environmental samples using the synergistic effect in an optical sensor.

A new eco-friendly method for creating an optical sensor membrane specifically designed to detect yttrium ions (Y3+) has been developed. The proposed sensor membrane is fabricated by integrating 4-(2-arsonophenylazo) salicylic acid (APASA), sodium tetraphenylborate (Na-TPB), and tri-n-octyl phosphine oxide (TOPO) into a plasticized poly(vinyl chloride) matrix with dimethyl sebacate (DMS) as the plasticizer. In this sensor membrane, APASA functions dually as an ionophore and a chromoionophore, while TOPO enhances the complexation of Y3+ ions with APASA. The composition of the sensor membrane has been meticulously optimized to achieve peak performance. The current membrane exhibits a linear dynamic range for Y3+ ions from 8.0 × 10-9 to 2.3 × 10-5 M, with detection and quantification limits of 2.3 × 10-9 and 7.7 × 10-9 M, respectively. No interference from other potentially interfering cations and anions was observed in the determination of Y3+. The membrane showed strong stability and a swift response time of about 3.0 minutes, with no signs of APASA leaching. This sensor is highly selective for Y3+ ions and can be renewed by treating it with 0.15 M HNO3. It has been effectively applied to measure Y3+ in nickel-based alloys, as well as in biological and environmental samples.

Potential of electrospun fibrous membranes involving tri-n-octylphosphine oxide for selective clearance of uremic toxin p-cresol over urea and creatinine

In this study, various electrospun and electrosprayed fibrous membranes from polyethersulfone (PES) and polyvinylpyrrolidone (PVP) were fabricated, to which a common solvating extractant tri-n-octylphosphine oxide (TOPO) was incorporated. Such TOPO-involved PES membranes were attempted to selectively clear p-cresol, one of trace amounts of small uremic toxins, from simulated serum via hydrogen bonding. Morphological and physicochemical properties of the as-synthesized fibrous membranes were first studied. Batch tests displayed that the equilibrium of p-cresol adsorption on all fibrous membranes were attained within 2 h. Analysis of adsorption isotherms of p-cresol by the Langmuir equation revealed that the adsorption was improved in the presence of TOPO; moreover, the distribution state of TOPO powders along the fibers played an important role in membrane performance. Among the six as-prepared TOPO-incorporated membranes, the highest adsorption capacity of p-cresol in simulated serum at 37oC and pH 7.4 reached to be 21.7 mmol per gram of TOPO. The operational stability of as-prepared fibrous membranes was evaluated by checking their adsorption ability, membrane weight, water contact angle, structural changes by SEM imaging, and PVP dissolution using UV–Vis spectroscopy, both before and after exposure to PBS solution. Crossflow permeation-adsorption of a multicomponent mixture (0.46 mmol/L of p-cresol, 1.33 mmol/L of creatinine, and 38.3 mmol/L of urea) for 4 h indicated that the prepared membranes yielded a high selectivity toward p-cresol against creatinine and urea of 21.2–43.0 and 10.8–18.5, respectively. Hemolysis tests and viability measurements of both human umbilical vein endothelial cells and THP 1 monocytic leukemia cells demonstrated that the proposed configurations of the TOPO-incorporated fibrous membranes were hemo- and bio-compatible. Our results on the composition and systematic design of these fibrous membranes suggested that they can serve as an advanced hemoperfusion unit, maintaining high p-cresol removal and bio-compatibility. These well-designed membrane-based devices could be connected in series with the conventional hemodialysis devices to further improve the overall removal of small uremic toxins.

Trioctylphosphine oxide-based hydrophobic magnetic deep eutectic solvent as a novel extractant for the enrichment of primary aromatic amines from juice and environmental water

In this study, a novel technique utilizing vortex-assisted dispersive liquid-liquid microextraction with magnetic deep eutectic solvents (MDESs) was established and coupled with HPLC-UV to analyze six primary aromatic amines (PAAs). A novel hydrophobic MDES prepared from trioctylphosphine oxide, octanol, and CoCl2 was used as the extractant, which could be dispersed uniformly during extraction, then floated onto the sample surface and re-aggregated into a single drop spontaneously after the extraction. The variables influencing the efficiency of the extraction process were investigated. When performing under the optimal extraction conditions, this method exhibited excellent linearity, low limits of detection (0.2–0.9 ng mL−1), and high precision (RSD ≤ 8.3 %). The enrichment factors ranged from 56 to 182. Satisfactory recoveries in the range of 91.6–109.2 % with RSDs < 7.1 % were obtained from three apple juices and three environmental water samples. The greenness and practicality of the developed method were assessed by AGREE, AGREEprep, and blue applicability grade index metric tools. Overall, the established procedure demonstrated its simplicity, speediness, environmental friendliness, and effectiveness in analyzing PAAs from aqueous matrices.

An eco-friendly and high-yield extraction of rare earth from the leaching solution of ion adsorbed minerals

Ion-adsorbed rare earth minerals are rich in medium and heavy rare earth (RE), which are important strategic resources. In this article, a novel approach for the extraction of RE from ion adsorbed minerals was developed. Through a comprehensive assessment of their extraction and separation performance, the hydrophobic deep eutectic solvents (HDES) with a composition of trioctylphosphine oxide (TOPO): dodecanol (LA): 2-thiophenoyltrifluoroacetone (HTTA) = 1:1:1 was determined as the optimal configuration. Under optimized conditions, only RE were extracted by the HDES, while Al, Ca, Mg were not extracted at all. The HDES based extraction obviated the need for diluent such as kerosene, eliminating the generation of impurity removal residues. The RE in the stripping solution could be successfully enriched by saponified lauric acid, achieving an impressive precipitation rate of 99.7%. The RE precipitate underwent further enrichment, resulting in a RE concentration of 176 g/L (REO = 210 g/L). Unlike industrial precipitants such as oxalic acid and ammonium bicarbonate, lauric acid can be effectively recycled, thereby avoiding a large amount of wastewater and carbon dioxide emissions. The obtained RE solution product exhibits high yield and purity, this study provides an eco-friendly and high-yield approach for extracting RE.

The optimisation of caffeic acid reactive extraction by trioctylphosphine oxide using response surface methodology

ABSTRACT Caffeic acid is a valuable product due to its wide-ranging utilities. Currently, caffeic acid can be produced via fermentation process using native or engineered microorganisms. The reactive extraction is a prominent technique that is used for the recovery of carboxylic acids. In this work, caffeic acid was recovered by an organophosphate (trioctylphosphine oxide) from its aqueous solution in the presence of different kinds of solvents namely 1-butanol, ethyl propionate, and ethyl methyl ketone. The values of reactive extraction parameters were optimised by Box–Behnken design. 98.19% The maximum extraction efficiency was obtained as 98.19% at the optimum conditions of 0.003 mol kg−1 caffeic acid concentration, 50% (v/v) trioctylphosphine oxide quantity, and 306.2 K in the presence of 1-butanol as the solvent. Our study is the first ever to examine the reactive extraction of caffeic acid, and therefore very important in modern scientific disciplines.