Transparent Sheets Research Articles

Kill Two Birds with One Stone: Cracking Lithography Technology for High-Performance Flexible Metallic Network Transparent Conductors and Metallic Micronano Sheets.

Flexible electronics have sparked a wide range of exciting applications, such as flexible display technologies, lighting, sensing, etc. Flexible conductors are essential components of flexible electronics and seriously affect efficiency and overall performance. Here, a facile and kill-two-birds-with-one-stone strategy of cracking lithography technology has been proposed to simultaneously fabricate two high-performance flexible conductors, flexible metallic network transparent conductors (f-NTCs) and metallic micronano sheets (MMNSs). The PET substrate flexible transparent conductors (FTCs) based on this strategy yield 88.1% transparency within the visible spectrum and a sheet resistance of 9 Ω/sq. In addition, the FTCs show exceptional mechanical stability, with the sheet resistance remaining virtually unchanged even after 6000 s of bending tests. Subsequently, the remaining MMNSs are recycled to manufacture a Ag paste, showing a very low conductive percolation threshold (∼13%) and excellent flexibility with 140% breaking elongation. After 1000 s of stretching tests, it showed excellent mechanical stability. Furthermore, flexible electroluminescent devices based on the FTCs and sensors fabricated with MMNSs both show excellent performance, demonstrating their potential wide applications in flexible electronics.

A-351 Versatile and Sensitive Microfluidic Immunoassay for Improved Point-of-Care Diagnostics

Abstract Background Healthcare professionals must choose between sensitivity and ease-of-use in diagnostics, particularly for diseases like COVID-19 and strep throat. Traditional enzyme-linked immunosorbent assays (ELISAs) are sensitive but are manually intensive and lengthy. Lateral flow assays (LFAs) are an alternative with low cost, ease-of-use, and rapid results; but LFAs suffer from low sensitivity. Burst Diagnostics presents a groundbreaking solution with the capillary-driven immunoassay (CaDI), a novel microfluidic device delivering sensitivity comparable to ELISA with the ease of LFAs. Methods The CaDI is made of flow channels defined by layered transparency and adhesive sheets containing reagent pads with HRP-conjugated antibody and luminol. The system requires only a sample addition step by the user. Sample flow initiates sequential steps of a sandwich ELISA, fully automated by the device, to provide a chemiluminescent signal in 10 minutes or less, depending on sample matrix. Results We have demonstrated success with preliminary studies for the detection of SARS-CoV-2 nucleocapsid protein (NP) and group A streptococcus (GAS). Detection of NP was achieved by assembling and optimizing COVID-19 CaDI’s using anti-NP antibodies. Then, spiked nasal swab samples were tested ranging from 10 to 1000 PFU/mL with positive detection as low as 10 PFU/mL, much less than the same samples in a traditional LFA (see figure). Additionally, we have demonstrated successful detection of GAS in optimized buffer conditions up to 100-fold less than commonly used LFAs. Finally, multiplexed CaDI’s increase throughput and cost-effectiveness in the point-of-care setting. Conclusions The CaDI platform bridges the ease of LFAs and sensitivity/specificity of laboratory tests. Currently, the CaDI can detect SARS-CoV-2 NP and GAS with higher sensitivity than existing LFAs. Development is underway for a reader to accompany the CaDI and further simplify the test. Importantly, the potential targets for detection are immense due to the sensitivity, simplicity, and adaptability of the platform.

Review of thermal neutron scintillators: Evaluation metrics and future prospects for demanding applications

Neutron applications are progressing rapidly, requiring detectors to meet increasingly rigorous criteria. Specifications such as high neutron counting rates, fast timing resolution and low background have a significant impact on choice of scintillator and how scintillators are evaluated. This work considers detector requirements for neutron scattering instruments that are becoming more stringent as the sources and scattering technologies continue to improve. Meanwhile, both prominent scintillators used for neutron scattering detectors, ZnS:Ag/6LiF and GS-glass, remain stagnant. While these scintillators have been suitable for many years, they are becoming a limiting factor for neutron scattering instruments. ZnS:Ag is inhibiting count rate capability and GS-glass is too gamma sensitive so alternatives need to be found. A brief explanation of neutron scattering, its detector requirements and how those relate to scintillator properties will be discussed. Furthermore, this work explains how standard characterization methods and reporting of scintillation properties are not entirely suitable for high count rate, low background applications like neutron scattering. As a result, modifications to characterization of gamma discrimination, light output, and decay kinetics are suggested. Additional steps are suggested including neutron activation and a more appropriate assessment of count rate capability. A non-exhaustive set of 6Li containing neutron sensitive scintillators including ZnS:Ag/6LiF, GS20 glass, ZnO:Zn/6LiF, Cs6LiYCl:Ce, 6LiI:Eu, 6LiI:Ce, 6LiCaAlF:Eu, LiCaAlF:Ce, transparent rubber sheet (TRUST) 6LiCaAlF:Eu, TRUST 6LiCaAlF:Eu with added fluorophore and EJ-270 (6Li containing plastic) are reviewed and studied from this different perspective. Finally, new scintillator developments relevant to high count rate, low background applications are discussed.

Xanthated cellulose nanofibers dispersion: Stability, pickering emulsion with styrene, and latex composite via polymerization

Leveraging xanthated cellulose nanofibers (XCNF) from a modified rayon process, this study explores their use as stabilizers in Pickering emulsion polymerization for nanocomposite production. XCNF was produced from softwood pulp through a xanthation process that utilized a reduced NaOH concentration of 8.5 %, lower than the typical rayon process, and was followed by mechanical defibrillation, resulting in fiber widths under 10 nm. Following the protective allylation of xanthate groups and hydrophobic modification, 1H NMR analysis was conducted, revealing a xanthation degree of 0.144. When stored at 4 °C, a 0.5 wt% XCNF dispersion gelled by the fifth day, as confirmed by visual and rheological assessments. UV and TEM analyses indicated xanthate detachment and nanofiber aggregation over time, respectively. The addition of a low-temperature initiator to the XCNF-stabilized styrene-water emulsion enabled polymerization, yielding nanofiber-encapsulated polystyrene latex. This led to transparent sheets upon thermal pressing, demonstrating the potential of XCNF in developing polymer nanocomposites.

Determining storage for pressure-sensitive tape evidence: A long-term study.

Tape is a type of trace evidence commonly seen in forensic science. Little to no research has been published regarding the optimal storage material for pressure-sensitive adhesive (PSA) tape. The purpose of this project was to determine the substrate with the least amount of interference for storing PSA tape. Interferences such as difficulty removing tape from the substrate or substrate components leaching into the adhesive can affect the analysis. This was a long-term study in which samples were stored on various substrates for nearly 10 years. Ten different tape samples were placed on eight different substrates for a total of 80 samples. The substrates included typical materials currently used for tape storage as well as other, less common materials. The tape samples were evaluated for ease of removal at various time intervals. The adhesives from each tape were analyzed at similar time intervals by Fourier transform infrared spectroscopy (FTIR). In addition, the adhesives were analyzed by pyrolysis gas chromatography-mass spectrometry (PyGC-MS), scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS), and x-ray fluorescence (XRF) at the last time interval (112 months) and compared to the adhesive tape samples from the original rolls of tape to determine if there was any adverse effect from the substrates during storage. The FedEx backing was the only substrate that had no adverse effects regarding ease of removal. The substrates that had the least effect on the adhesive for both short-term and long-term storage included FedEx backings, adhesive sheet backings, and polyester transparency sheets.

Large-Area Film Thickness Identification of Transparent Glass by Hyperspectral Imaging.

This study introduces a novel method for detecting and measuring transparent glass sheets using hyperspectral imaging (HSI). The main goal of this study is to create a conversion technique that can accurately display spectral information from collected images, particularly in the visible light spectrum (VIS) and near-infrared (NIR) areas. This technique enables the capture of relevant spectral data when used with images provided by industrial cameras. The next step in this investigation is using principal component analysis to examine the obtained hyperspectral images derived from different treated glass samples. This analytical procedure standardizes the magnitude of light wavelengths that are inherent in the HSI images. The simulated spectral profiles are obtained using the generalized inverse matrix technique on the normalized HSI images. These profiles are then matched with spectroscopic data obtained from microscopic imaging, resulting in the observation of distinct dispersion patterns. The novel use of images coloring methods effectively displays the thickness of the glass processing sheet in a visually noticeable way. Based on empirical research, changes in the thickness of the glass coating in the NIR-HSI range cause significant changes in the transmission of infrared light at different wavelengths within the NIR spectrum. This phenomenon serves as the foundation for the study of film thickness. The root mean square error inside the NIR area is impressively low, calculated to be just 0.02. This highlights the high level of accuracy achieved by the technique stated above. Potential areas of investigation that arise from this study are incorporating the proposed approach into the design of a real-time, wide-scale automated optical inspection system.

Optofluidic phase modulator based on electrowetting liquid lens

In this paper, a liquid optical phase modulator modified from a cylindrical two-liquid electrowetting liquid lens is presented. A movable optical plane is constructed by fixing a transparent sheet between two immiscible liquids. By using the electrowetting effect to flatten the optical plane along the through-light direction, the length ratio of the two liquids in the through-light direction can be fine-tuned to modify the optical path to realize phase modulation. To validate this concept, we experimentally fabricated a prototype phase modulator and tested its phase modulation capability. Experiments show that the phase shift range can be up to 5.82 π and the phase shift accuracy can be up to λ/60, a drive time of 72 ms and a relaxation time of 34 ms within the range of applied voltage 40–80 V DC voltage.

Enhancing Solar Photovoltaic Panel Performance in India's Tropical Climate: An Experimental Study on the Influential Effects of Optical Filters

<p>Due to the increasing global energy demand and consequent climate change from burning fossil fuels, researchers are getting more focused on renewable energies as a potential solution to the world's energy problems. Solar energy is a prominent form of sustainable energy. The solar photovoltaic power generation system’s electrical performance is negatively influenced by several factors, including the impact of solar irradiance, incident angle, temperature, dust accumulation on the top of the solar cell, cracks in the solar panel, shadowing, shunt resistance, solar cell materials, load mismatch, maintenance and cleaning schedule, spectral mismatch loss, and cable loss. The direct environmental factors that have the biggest impact on efficiency are the effects of sun irradiance and temperature. This empirical investigation examined the impact of optical filters on the electrical efficiency of a 40W polycrystalline solar PV panel in India while considering real-time ambient conditions. Through the utilization of an optical filter, the solar PV panel's temperature is diminished, hence enhancing the output power of the solar panel. Based on the experimental findings, the utilization of a transparent plexiglass sheet equipped with a coolant system installed on the solar panels leads to a drop in the average operating temperature of the solar PV module by up to 6°C. Additionally, the output power is enhanced by up to 10W in comparison to the reference solar panel’s output performance.</p>

Analysis of PVC-based Product Inventory Control with Economic Production Quantity and Lagrange Multiplier Methods at PT. XYZ

PT XYZ is a manufacturing company that produces various kinds of products made from PVC (Polyvynil Chloride). Some of the PVC-based products produced by PT XYZ are transparent sheet, colour sheet, and flooring. The problem that exists at PT XYZ is that the company often produces more than the amount of demand which makes the company have to prepare a storage warehouse with a capacity as large as the number of products produced. With this, the storage warehouse experiences overcapaity in controlling the inventory of products produced by the company. And it can be concluded that the problem that occurs at PT XYZ is inventory control and production quantity planning that has not been well planned. Based on the problems that occur at PT XYZ, the most suitable method used to solve these problems is the Lagrange Multiplier method. This research has a purpose to control the inventory of products made from PVC so as to minimize the total cost of product inventory at PT. XYZ. From the research This study found the optimal production amount of 1,332,999 m. Where with the amount of production, the company needs a warehouse area of 9,299.9 m3. The total inventory cost calculated using the Lagrange Multiplier method is IDR 377,073,841,401 while the company's total inventory cost is IDR 402,844,596,680. So that a savings of IDR 25,770,755,279 or 6.40% is obtained.

Soft yet mechanically robust injectable alginate hydrogels with processing versatility based on alginate/hydroxyapatite hybridization

The salient gelling feature of alginate via forming the egg-box structure with calcium ions has received extensive interests for different applications. Owing to the interfacial incompatibility of rigid inorganic solids with soft polymers, the requirement of overall stereocomplexation with calcium released from uniformly distributed solids in alginate remains a challenge. In this study, a novel alginate-incorporated calcium source was proposed to tackle the intractable dispersion for the preparation of injectable alginate hydrogels. Calcium phosphate synthesis in alginate solution yielded CaP-alginate hybrids as a calcium source. The physicochemical characterization confirmed the CaP-alginate hybrid was a nano-scale alginate-hydroxyapatite complex. The colloidally stable CaP-alginate hybrids were uniformly dispersed in alginate solutions even under centrifugation. The calcium-induced gelling of the CaP-alginate hybrids-loaded alginate solutions formed soft yet tough hydrogels including transparent sheets and knittable threads, confirming the homogeneous gelation of the hydrogel. The gelation time, injectability and mechanical properties of the hydrogels could be adjusted by changing preparation parameters. The prepared hydrogels showed uniform porous structure, excellent swelling, wetting properties and cytocompatibility, showing a great potential for applications in different fields. The present strategy with organic/inorganic hybridization could be exemplarily followed in the future development of functional hydrogels especially associated with the interface integration.

Microwave irradiation-induced yield enhancement of coconut shell biomass-derived graphene-like material

This paper reports a new strategy (rapid and selective microwave irradiation) to achieve an improved yield of graphene-like material derived from coconut shell biomass. The influence of various microwave irradiation (MWI) powers (80, 240, and 400 W) treatment on the crystalline structures, morphology, and electrochemical performance of the produced samples was determined and compared with the virgin-untreated specimen. The obtained samples were analyzed using varied analytical techniques. The FESEM images of the irradiated samples revealed the existence of graphene-like morphologies accompanied by some thin and transparent sheets. The sample at 80 W displayed the best quality with the highest yield, improving the carbon content, reducing the oxygen functional groups, and increasing the BET-specific surface area by as much as 1238.48 m2/g. The electrochemical properties of the sample treated at 80 W (optimum MWI power treatment) exhibited rectangular curves against scanning speeds, indicating an ideal capacitive behaviour called electric double-layer capacitance (EDLC). It is asserted that the proposed systematic and eco-friendly approach in obtaining the high-performance graphene-like material at low cost may open up sundry opportunities for practical applications, leading towards sustainable development.

Higher-Order Structural Analysis of a Transparent and Flexible High Thermal Conductive Liquid Crystalline Elastomer Sheet and Its Composite.

Transparency, flexibility, and high thermal conductivity are trade-offs. Specifically, we have investigated a cross-linked acrylic liquid crystal elastomer (LCE) that exhibits both transparency and flexibility while maintaining a high level of thermal conductivity. The transparent monodomain LCE sheet was achieved through a process of stretching an initially opaque polydomain sheet to 80% elongation and subsequently subjecting it to photocuring. The thermal conductivity in the stretching direction (x) of the monodomain LCE sheet was found to be 1.8 times higher than that of the prestretched polydomain sheet, consistent with findings from previous studies. However, in the orthogonal direction (y) to the stretching (x) direction, the thermal conductivity exhibited an even higher value, being 1.7 times greater than in the x-direction, with a value of 3.0 W/(m·K). This unique observation prompted us to conduct further investigation through higher-order structural analysis of these LCE sheets using 2D wide-angle X-ray scattering (WAXS) analysis. In the transparent sheet, the LCE molecules were aligned in the sheet in the stretching x-direction (monodomain structure) for the out-of-plane direction. However, in the in-plane x-direction, the molecular plane spacing exhibited random orientation at a period of 0.45 nm. In contrast, within the y-direction of the inner layer, the molecular plane spacing exhibited a uniaxial horizontal orientation at the same period length as in the x-direction. The heat energy entering into the y-direction once spreads to the x-direction, but it was considered that the reason for the higher thermal conductivity to the y-direction would be forming covalent bonds that function as new heat transmission paths, in the direction intersecting to the x-direction during photocuring. Therefore, we concluded that the synergistic effect of the high level of the ordered inner structure and covalent bonding structure due to cross-linking in the y-direction contributes to its higher thermal conductivity compared to that in the x-direction, which exhibits a random in-plane structure. Additionally, we have fabricated an LCE composite sheet filled with 75 vol % of alumina particles using a polydomain-type LCE as the base material. The composite sheet exhibits remarkable thermal conductivity in the thickness direction, measuring at 9.8 W/(m·K), while maintaining a flexibility characterized by an elastic modulus of 70 MPa. This thermal conductivity surpasses that of a nonmesogenic acrylic composite sheet with identical alumina particle filling, which measured at 3.9 W/(m·K), more than twice as much. The presence of the mesogen skeleton has been demonstrated to enhance heat transfer, even within soft composites, by facilitating the formation of an ordered structure.

Preparation of polypropylene nanofibers reinforced multifunctional epoxy composite concrete with ultraviolet‐driven afterglow emission

AbstractIn order to develop smart concrete with afterglow emission, epoxy resin (EPX) was immobilized with nanoparticles of alkaline earth aluminate (NAEA) as a photoluminescent agent and electrospun polypropylene nanofibers (EPN) as a reinforcement agent. Scanning electron microscope images of EPN displayed diameters of 70–90 nm, whereas transmission electron microscopic images showed that NAEA has diameters of 3–9 nm. To create a transparent sheet that glows in the dark, NAEA were physically immobilized in EPN@EPX composite. CIE Lab and photoluminescence spectrum studies demonstrated that EPN@EPX bars turned greenish upon exposure to ultraviolet (UV) rays and greenish‐yellow in a darkened box. The luminous EPN@EPX morphologies and chemical compositions were analyzed using various analytical methods. The resistance to scratching of EPN@EPX bars was monitored to considerably increase with increasing NAEA concentration. The photoluminescence spectrum demonstrated two emission peaks at 437 and 518 nm. Photoluminescent EPN@EPX hybrids with low NAEA content have shown rapid photochromism reversibility. On the contrary, NAEA‐rich EPN@EPX bars displayed slow reversibility, glowing in the dark. Superhydrophobicity and UV blockage were found to be significantly improved in the luminescent colorless EPN@EPX hybrids.

Two-dimensional time-resolved scintillating sheet monitoring of proton pencil beam scanning FLASH mouse irradiations.

Dosimetry in pre-clinical FLASH studies is essential for understanding the beam delivery conditions that trigger the FLASH effect. Resolving the spatial and temporal characteristics of proton pencil beam scanning (PBS) irradiations with ultra-high dose rates (UHDR) requires a detector with high spatial and temporal resolution. To implement a novel camera-based system for time-resolved two-dimensional (2D) monitoring and apply it in vivo during pre-clinical proton PBS mouse irradiations. Time-resolved 2D beam monitoring was performed with a scintillation imaging system consisting of a 1mm thick transparent scintillating sheet, imaged by a CMOS camera. The sheet was placed in a water bath perpendicular to a horizontal PBS proton beam axis. The scintillation light was reflected through a system of mirrors and captured by the camera with 500 frames per second (fps) for UHDR and 4 fps for conventional dose rates. The raw images were background subtracted, geometrically transformed, flat field corrected, and spatially filtered. The system was used for 2D spot and field profile measurements and compared to radiochromic films. Furthermore, spot positions were measured for UHDR irradiations. The measured spot positions were compared to the planned positions and the relative instantaneous dose rate to equivalent fiber-coupled point scintillator measurements. For in vivo application, the scintillating sheet was placed 1cm upstream the right hind leg of non-anaesthetized mice submerged in the water bath. The mouse leg and sheet were both placed in a 5cm wide spread-out Bragg peak formed from the mono-energetic proton beam by a 2D range modulator. The mouse leg position within the field was identified for both conventional and FLASH irradiations. For the conventional irradiations, the mouse foot position was tracked throughout the beam delivery, which took place through repainting. For FLASH irradiations, the delivered spot positions and relative instantaneous dose rate were measured. The pixel size was 0.1mm for all measurements. The spot and field profiles measured with the scintillating sheet agreed with radiochromic films within 0.4mm. The standard deviation between measured and planned spot positions was 0.26mm and 0.35mm in the horizontal and vertical direction, respectively. The measured relative instantaneous dose rate showed a linear relation with the fiber-coupled scintillator measurements. For in vivo use, the leg position within the field varied between mice, and leg movement up to 3mm was detected during the prolonged conventional irradiations. The scintillation imaging system allowed for monitoring of UHDR proton PBS delivery in vivo with 0.1mm pixel size and 2ms temporal resolution. The feasibility of instantaneous dose rate measurements was demonstrated, and the system was used for validation of the mouse leg position within the field.

Fabrication and characterization of Screen-printed Graphite and Nickel Based Thick Film Resistive Strain Sensor

Piezo resistive properties of thick film resistors are shown by a variety of nanomaterials, in which graphite and nickel are used to study the piezo resistive response in this paper. The present work proposes to fabricate stain sensor on substrates like PVC, and transparent plastic sheet. Screen printing method is used for patterning of sensor on the substrates with two different inks namely piezo resistive ink made of graphite and nickel powder and conductive ink made of silver. Change in resistance of the fabricated sensor is noted for the changes in force applied on the sensor and corresponding gauge factor is observed to be around 10.5 and 11 for PVC and OHP respectively. The screen-printed strain gauge performance is investigated and presented in this paper. This study of mechanical test results demonstrate that the sensor can be used for micro strain detection in various applications.

Keratin protein nanofibers from merino wool yarn: a top-down approach for the disintegration of hierarchical wool architecture to extract α-keratin protein nanofibers.

We report the extraction of keratin nanofibers from the medulla of a parent yarn after denaturing the cuticle and cortex microstructures of a merino wool yarn. Controlled alkaline hydrolysis, followed by high-speed blending in acetic acid, allowed for the extraction of keratin protein nanofibers with an average diameter of 25 nm and a length of less than 3 μm. SEM and AFM analyses showed the removal of cuticle cells from the yarn. FT-IR and DSC analyses confirmed the hydrolysis and denaturation of the sheet protein matrix of cuticle cells. XPS analysis provided strong evidence for the gradual removal of the epicuticle, cuticle cells, and cortex of the hierarchical wool structure with an increase in alkaline hydrolysis conditions. It was confirmed that the merino wool yarn subjected to hydrolysis under alkaline conditions exposed its internal fibrillar surface. In an acetic acid medium, these fibrillar surfaces obtained a surface charge, which further supported the defibrillation of the structure into its individual nanofibrils during high-speed blending. The extracted nanostructures constitute mainly α-helical proteins. The morphology of the nanofibers is composed of a uniform circular cross-section based on the images obtained using AFM, TEM, and SEM. The extracted nanofibers were successfully fabricated into transparent sheets that can be used in several applications.

Falcataria moluccana (Miq.) root distribution seedlings in response to nitrogen concentrations and tillage

Abstract Falcataria moluccana (Miq.) Barnaby & Grimes is an important species for forest plantation programmes in Malaysia and is widely used in the wood industry. However, its root interactions have not been widely investigated due to the limited methodologies and information about the root distribution of trees and crops in forest plantation and agroforestry systems. This study was conducted to determine the rhizotron-scale root interactions of F. moluccana at different tillage and nitrogen concentrations under four different treatments: control, tillage, fertiliser, and tillage with fertiliser. The rhizotron-scale experiment was conducted at a greenhouse where F. moluccana (Batai) seedlings were transplanted in transparent rhizotron tubes (onemetre-high transparent polycarbonate solid sheet) using topsoil and river sand to simulate natural growing conditions. Root Intensity (RI), Root Length Density (RLD), Specific Root Length (SRL), dried shoot bio-mass and root biomass were recorded. Root biomass and SRL were notably higher (25–50 cm depth) at 6 WAT (Weeks After Transplanting), and the shoot biomass (tillage + fertiliser) was significantly higher at 14 WAT. However, plants treated with different tillage and nitrogen concentrations showed no significant impact on the RI and RLD. Fertiliser treatment only, and tillage with fertiliser treatment, showed greater root distribution at the rhizotron scale. These findings contribute to forest plantation and natural forest rehabilitation efforts by helping optimise the soil resources within ecosystems for sustainable forest management.

Bimetal Enriched Carbon Nanomaterials Synthesized from Bagasse- A Plant Waste Material as an Exceptional Adsorbent for Hydrogen Gas

Abstract: In this study, the process of pyrolysis has been depicted for the synthesis of CNMs from the Bagasse-a plant waste materials at high temperature of 750℃ in an inert atmosphere. The Taguchi optimization methodology is utilized to optimize the parameters for synthesis process. The adsorption of hydrogen was investigated using Sievert’s apparatus. The SEM image demonstrates the bimetal enriched CNMs and HRTEM reveals the CNMs obtained were in cylindrical form as well as transparent sheet. The presence of various bimetal combination is confirmed by EDAX. The spectroscopic studies XRD and Raman reveals the graphitic nature of the CNMs. 4.96 weight percent hydrogen adsorption was demonstrated by CNMs synthesized from bagasse under the parameters predicted by the Taguchi optimization methodology.

Portable contactless caliper.

This work presents a portable optical meter for noncontact thickness measurement. The device shines a focused laser light on a thin and transparent sample, resulting in an interference between light reflecting from the top and from the bottom surface, and the interfering pattern is recorded by a linear sensor array before data analysis with an Arduino microcontroller. The device produced accurate thickness values from glass cover slips and transparent plastic sheets within a fraction of a second per measurement. Additionally, the sample's refractive index is not required a priori. Therefore, it has a high potential to be of use in real-time quality control in transparent thick-film coating and manufacturing.

Development of photoluminescent concrete from polystyrene plastic reinforced with electrospun polypropylene nanofibers

Polystyrene (PS) plastic was reinforced with electrospun polypropylene nanofibers (EPN) and nanoparticles of lanthanide-doped aluminate (NLA) to develop mechanically reliable transparent, photochromic and afterglow materials. Different concentrations of lanthanide-doped aluminate nanoparticles, from 0.5 % to 12 % w/v, were physically integrated into a transparent plastic sheet of electrospun polypropylene nanofibers@polystyrene (EPN@PS). The transparent hybrid samples of EPN@PS, as determined by CIE Lab and luminescence spectroscopy, appeared green (518 nm) underneath UV lamp. The morphological properties of NLA revealed diameters of 5–15 nm, whereas the electrospun polypropylene nanofibers displayed diameters of 75–225 nm. Different analytical methods were used to investigate the morphology of the EPN@PS substrates. Reinforcing polystyrene with EPN as a roughening agent and NLA as a photoluminescent agent improved its mechanical properties. Photoluminescent substrates of EPN@PS were shown to have much better scratch resistance than NLA-free plastic. When excited at 365 nm, the photoluminescence spectra showed an emission peak at 518 nm. The results demonstrated that the superhydrophobic and UV-blocking of the EPN@PS composites were enhanced upon increasing the phosphor content. The highest contact angle of concrete was monitored at 151.8°. The current strategy is significant in various applications, such as smart concretes, electricity-free lightening, smart windows, and anti-counterfeiting labeling.