Transmission Of Millimeter-wave Signals Research Articles

PDM-OFDM 1-bit DSM 1024QAM/4096QAM signals at W-band transmission over 4.6-km wireless distance.

In this Letter, we propose the application of delta-sigma modulation (DSM) higher-order quadrature amplitude modulation (QAM) technology in long-distance transmission of W-band wireless communication, and demonstrate, for the first time to the best of our knowledge, the wireless transmission of millimeter wave signals in the W-band based on 1-bit DSM quantization using polarization-division-multiplexed orthogonal frequency division multiplexing (PDM-OFDM) 1024QAM/4096QAM for 4.6 km. We successfully achieved a bit error rate (BER) of 40-Gbit/s PDM-OFDM 1024QAM and 48-Gbit/s PDM-OFDM 4096QAM after 4.6-km wireless transmission, both lower than the soft decision forward error correction (SD-FEC) of 4.2 × 10-2. To the best of our knowledge, this is the first time that up to 4096QAM signals have been quantized and transmitted based on 1-bit DSM in a 4.6-km-long distance W-band millimeter wave system.

Performance optimization of RSOA based mm-wave radio-over-fibre access network

In this paper, a Reflective Semiconductor Optical Amplifier based, Radio-over-Fibre access network configuration has been proposed to feed future millimeter-wave radio systems. The system architecture combines several approaches to overcome the challenges of millimeter-wave signal transmission. Reflective semiconductor optical amplifier modulator realizes a colorless and relatively cost-effective Remote Antenna Unit. The same optical carrier is used for both downlink and uplink. Optical single-sideband modulation is used at the downlink, which is robust against chromatic dispersion, but the complex realization of this modulation format is not possible at the Remote Antenna Unit. Optical intermediate frequency transmission is applied at the uplink direction, and the required local oscillator signal originates from the central station. The critical element is the reflective optical amplifier, as it compensates for the optical loss and works as an external intensity modulator. The operation of the reflective optical amplifier is modeled by multisection rate and wave equation-based description. The amplification and modulation behaviors of an available reflective optical amplifier are also measured. The experimental work validated the colorless operation and the quality of the modulation versus bias current and input optical power. Finally, system simulation was realized. The uplink and downlink power budgets were balanced, and optimal values for the optical coupling rate and RSOA bias current have been selected.

Investigation of de-embedding techniques applied on uni-traveling carrier photodiodes

AbstractThe generation and transmission of millimeter-wave signals for 5G applications require the use of broadband and high output power photodetectors to bridge from the optical and electronic domains. Therefore, the deep knowledge on the equivalent circuit characteristics of these devices is vital. This study reviews and analyzes de-embedding techniques contributing to the characterization of the physical aspects within the active region of uni-traveling carrier photodiodes. De-embedding methods analytically remove the parasitic effects of the electrical transmission lines connected to their active area allowing the extraction of their series resistance and junction capacitance toward the synthesis of an equivalent circuit with lumped elements. The open-short technique is examined and a systematic error introduced by this process underlines the vulnerability of the method on removing parasitics with higher complexity. This error is quantified leading to the implementation of a corrected equation converging with the characteristic features of an $S$-parameter-based de-embedding. These characteristics are also analyzed through simulation approaches showing minimal equivalent inaccuracies on eliminating more complex symmetrical parasitics. A thorough comparison between these three methods is conducted through the calculation of lumped components corresponding to the active region of diodes with different sizes.

Polarizationmultiplexing based duplex radio-over-fiber link for millimeterwave signal transmission to a ring of multiple radio access units

A radio-over-fiber (RoF) distributed antenna system (DAS) architecture is proposed, where millimeter wave (mm-wave) signals are transmitted to four different radio access units (RAUs) arranged in a ring topology. The proposed architecture transmits duplex data of 128 Mb/s to each RAU in both downlink (DL) and uplink (UL) directions. The radio frequency (RF) signals are transmitted by polarization multiplexing a multi-wavelength source. Millimeter-wave signals at a frequency of 25 GHz are generated at each RAU using remote heterodyne detection. The proposed architecture provides increased coverage while maintaining good bit error rate (BER) results.

Fiber-FSO/wireless convergent systems based on dual-polarization and one optical sideband transmission schemes

A bidirectional fiber-free-space optical (FSO)/wireless convergent system that uses dual-polarization and one optical sideband transmission schemes for hybrid vestigial sideband (VSB)–four-level pulse amplitude modulation (PAM4)/millimeter-wave signal transmission is proposed and demonstrated. Using a dual-polarization scheme, one optical sideband that is modulated by a 56 Gb s−1 VSB–PAM4 signal (x-polarization) and another optical sideband that is modulated by a 10 Gbps data stream (y-polarization) are separated and polarized orthogonally. One optical sideband modulated by a 10 Gbps data stream (y-polarization) is delivered to efficaciously suppress the dispersion-induced limitation due to a span of 40 km single-mode fiber (SMF) and the distortion due to the beating among multiple sidebands. The proposed bidirectional fiber-FSO/wireless convergent system is a prominent one for providing broadband integrated services, such as the Internet, telecommunication, and 5G mobile networks.

Analysis of second order harmonic distortion due to transmitter non-linearity and chromatic and modal dispersion of optical OFDM SSB modulated signals in SMF-MMF fiber links

Single mode fibers (SMF) are typically used in Wide Area Networks (WAN), Metropolitan Area Networks (MAN) and also find applications in Radio over Fiber (RoF) architectures supporting data transmission in Fiber to the Home (FTTH), Remote Antenna Units (RAUs), in-building networks etc. Multi-mode fibers (MMFs) with low cost, ease of installation and low maintenance are predominantly (85–90%) deployed in-building networks providing data access in local area networks (LANs). The transmission of millimeter wave signals through the SMF in WAN and MAN, along with the reuse of MMF in-building networks will not levy fiber reinstallation cost. The transmission of the millimeter waves experiences signal impairments due to the transmitter non-linearity and modal dispersion of the MMF. The MMF exhibiting large modal dispersion limits the bandwidth-length product of the fiber. The second and higher-order harmonics present in the optical signal fall within the system bandwidth. This causes degradation in the received signal and an unwanted radiation of power at the RAU. The power of these harmonics is proportional to the non-linearity of the transmitter and the modal dispersion of the MMF and should be maintained below the standard values as per the international norms. In this paper, a mathematical model is developed for Second-order Harmonic Distortion (HD2) generated due to non-linearity of the transmitter and chromatic-modal dispersion of the SMF-MMF optic link. This is also verified using a software simulation. The model consists of a Mach Zehnder Modulator (MZM) that generates two m-QAM OFDM Single Sideband (SSB) signals based on phase shift of the hybrid coupler (90° and 120°). Our results show that the SSB signal with 120° hybrid coupler has suppresses the higher-order harmonics and makes the system more robust against the HD2 in the SMF-MMF optic link.

Direct and External Intensity Modulation in OFDM RoF Links

Radio-over-fiber (RoF) systems comprise light modulation and transmission of millimeter-wave signals over fiber links. The aim of this study is to investigate the performance of external and direct intensity modulation in RoF links and to analyze the drawbacks induced by different components of the optical system. In external modulation, the Mach-Zehnder modulator (MZM) is used, whereas the vertical-cavity surface-emitting laser (VCSEL) is utilized in direct modulation. Both modulation schemes are tested for a vector modulation format, i.e., the quadrature amplitude modulation (QAM), where an orthogonal frequency-division multiplexing (OFDM) scheme is used to generate signal subcarriers. The simulations are carried out with the same values of common global parameters for both schemes of intensity modulation. Although VCSEL is a promising device for future RoF systems, the external modulation shows a more robust performance compared with that of VCSEL when implemented with the OFDM modulation technique.

Development of Millimeter-Wave Radio-over-Fiber Technology

Millimeter-wave radio-over-fiber techno- logy demonstrates the potential for providing wireless broad-band service in the next generation wireless communication system. Optical generation of millimeter-wave signal is one of the most important technologies of millimeter-wave radio-over-fiber system. The virtues and shortcomings of some ways of optical generation of millimeter-wave signal are discussed. Then optical millimeter-wave signal transmission perfor- mance is described. Finally, an overview of the millimeter-wave radio-over-fiber system is given. It is suggested that the millimeter-wave radio-over-fiber technology should be paid more attention, especially for modulators for optical generation of millimeter-wave signal and radio-over-fiber system.

Generation of optical millimeter-wave signals and vector formats using an integrated optical I/Q modulator [Invited

This study discusses two key technologies used in radio-over-fiber (RoF) systems, namely, the generation and transmission of millimeter-wave signals and optical modulation schemes capable of carrying vector signal formats and utilizing the continuous performance improvements offered by digital signal processing. A cost-effective frequency-quadrupling technique capable of generating millimeter-wave signals up to 72 GHz is proposed. The generated optical millimeter-wave signals have very high quality, with an optical carrier and harmonic distortion suppression ratio exceeding 36 dB. An optical modulation scheme that can support a 64-QAM, 16 Gbits/s orthogonal frequency-division multiplexing RoF system is also demonstrated. Results of this study demonstrate that both methods offer realistic solutions to support future wireless systems.

Transmission Characteristics of 120-GHz-Band Wireless Link Using Radio-on-Fiber Technologies

The transmission characteristics of a 120-GHz-band millimeter-wave wireless link are described. The wireless link uses photonic technologies for generation, modulation, and transmission of millimeter-wave signals. This configuration enables set up of the photonic millimeter-wave generator and transmitter core separately; therefore, the wireless link can be used as a kind of radio-over-fiber system. The effects of transmitting 120-GHz-band optical subcarrier signals through single-mode fibers were theoretically and experimentally investigated. It was confirmed that the time shift of the code edges, because of chromatic dispersion, limits the transmission distance. A data stream at 10-Gbit/s was successfully transmitted over the 120-GHz-band millimeter-wave wireless link, with a bit error rate (BER) below 10-12 over a distance of 250 m. The results also demonstrated the stability of the wireless link, which satisfied the 10-Gb Ethernet standard under clear weather conditions.

Balance type pair transmission line for 60‐GHz band using multi‐layer substrate

AbstractFor a high‐density multilayer substrate ALIVH, balanced pair transmission lines on which 60‐GHz signals can be transmitted are proposed. First, it is shown that transmission of millimeter wave signals is difficult due to impedance mismatch of the vias in the conventional unbalanced transmission lines. Further, it is shown that transmission at up to 90 GHz is possible by a design such that the microstrip line on the surface, the strip line in the inner layer, and the vias connecting each layer have the same transmission line spacing and the same characteristic impedance. © 2006 Wiley Periodicals, Inc. Electron Comm Jpn Pt 2, 89(10): 1–8, 2006; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/ecjb.20249

Dispersion-induced power penalties in millimeter-wave signal transmission using multisection DBR semiconductor laser

In this paper, we present a simple analytical model to characterize the effect of fiber chromatic dispersion when using a multisection distributed-Bragg reflector (DBR) semiconductor laser as a millimeter-wave optical transmitter in a millimeter-wave fiber-radio system. We characterize the dispersion penalty of the laser as a function of the laser operating conditions and establish that the penalty is dependent on the distribution of optical power among the modes in the laser output. This, in turn, is dependent on the spectrum-filtering property of the laser DBR section and the gain profile of the laser. In addition to the dispersion penalty, the stability of the generated millimeter-wave carrier from the multisection laser is investigated, including the detected RF power and resulting phase noise. We establish that a compromise must be made when finding the optimum bias condition of the laser which provides minimum dispersion penalty, maximum received RF power, and minimum phase noise of the generated millimeter-wave carrier.

Transmission of millimeter-wave signals using uncoated telecommunications-grade distributed feedback lasers

Transmission of 2-Mb/s data at a subcarrier frequency of 35 GHz over 2.2 km of optical fiber by resonant modulation of an uncoated monolithic single-contact distributed feedback (DFB) laser is demonstrated. Modulation response, carrier-to-noise ratio and bit-error-rate results are reported. The tolerance of the resonant round-trip frequency to the DFB facet cleaving process and the device length uncertainty due to cleaving is also addressed in detail by computer simulation.

Fiber-optic microwave transmission using harmonic laser mixing, optoelectronic mixing, and optically pumped mixing

Three fiber-optical link configurations are proposed for use in microwave and millimeter-wave signal transmission. Harmonic laser mixing, optoelectronic mixing and optically pumped mixing are successfully utilized to achieve high carrier frequencies in fiber-optic links. The performance of harmonic laser diode mixers is experimentally investigated in the X-band. The p-i-n photodiode is used as an optoelectronic microwave mixer and an optically pumped microwave mixer, and the microwave characteristics of these mixers are demonstrated. These three fiber-optic link configurations show promise in transmitting microwave and millimeter-wave frequencies. >