Transformation Of Austenite Research Articles

Investigating the Role of TiC Precipitation in Dynamic Recrystallization Behavior of a Novel Ship Steel

This study examines the single‐pass thermal compression behavior of Ti‐bearing ship plate steel across a temperature range of 850–1150 °C and strain rates from 0.01 to 7 s−1, employing the Gleeble‐2000D thermomechanical simulator. It delves into the evolution of TiC precipitation and dynamic recrystallization (DRX), along with the austenite decomposition transformation during hot compression and subsequent cooling. Active dynamic recrystallization commences at deformation temperatures above 1050 °C, facilitated by the diminished pinning pressure of TiC carbides. This leads to the development of fine DRX austenite grains, influenced by an increase in strain rates and a decrease in temperature. Simultaneously, the fraction of TiC dispersions decreases as the deformation temperature increases, yet they maintain a consistent size of 5–10 nm. The refined particle size is attributed to their low interfacial energy with the austenite matrix, determined by the first principle to be 0.21 J m−2. Due to the severe deformation and numerous dispersions, specimens subjected to a thermal deformation regime at 850 °C and a strain rate of 7 s−1 present a peak in hardness, reaching a maximum of 324 HV. The Ti microalloying approach offers pivotal insights into improving the rollability and mechanical characteristics of ship plate steel.

Study on the effects of laser shock peening on the microstructure and properties of 17-7PH stainless steel

To investigate the surface integrity of 17-7PH stainless steel welded structural components used in aviation, laser shock peening (LSP) with different power densities was applied to stainless steel welded joints. The microstructural morphology, structural features, full-width at half-maximum, microhardness, and surface roughness of the stainless steel welded joint specimens before and after LSP were characterized and measured using SEM, TEM, XRD, a microhardness tester, and a high-resolution confocal microscope. The effects of different laser power densities on the microstructure and properties of the stainless steel welded joints were explored. Results indicate that the stainless steel welded joints exhibit a typical BCC phase. Laser shock peening promotes grain refinement in the welded joints, leading to the phase transformation of residual austenite into martensite. The surface roughness of the specimen is positively correlated with laser power density. At a power density of 5.17 GW/cm2, the surface roughness increased to 1.919 μm, which is 117.08% higher than that of the non-peened specimen. The microhardness of the specimens shows a decreasing trend with increasing power density. When the power density is 2.79 GW/cm2, the microhardness of the specimen significantly increases to 462.94 HV0.5, which is 22.26% higher than that of the non-peened specimen.

Mechanical behavior of shape memory alloys considering the effects of body fluids corrosion for biomedical applications

Abstract Shape memory alloys (SMAs) are widely used in biomedical engineering, including cardiovascular stents, artificial skeletons, and orthodontic implants. For the above applications, the body fluids corrosion processes will inevitably cause deterioration in the mechanical properties of the SMAs actuator during its service life, which will threaten the safety of human health. To analyze such problems, experimental measurements have been carried out to investigate the influence of body fluid corrosion on the mechanical properties of SMAs. Changes in the mechanical properties, such as Young’s modulus and phase transformation temperatures of SMAs under body fluids corrosion were tested firstly in the simulated body environment with the 0.9 wt. % NaCl solution at 37. With an increase of the immersion time, the results show that the Ti (titanium) percentage, austenitic (reverse) transformation start temperature, austenitic (reverse) transformation finish temperature, and maximum residual strain all increase, the Ni (nickel) percentage, martensitic transformation finish temperature, tensile strength, and yield strength decrease, and the martensitic transformation start temperature first decreases and then increases. The research in this work can provide an experimental basis for further study of the SMAs materials in biomedicine applications.

Selective laser melting fabrication of body-temperature shape memory NiTi alloy for 4D-printed orthopedic implants

ABSTRACT SLM fabrication of NiTi alloy is receiving increasing attention. However, the relatively high austenite transformation finish (Af) temperature is the main problem for biomedical applications. In this study, it was found that phase transformation temperature (PTT) increased with increasing laser power, decreasing scanning speed, and decreasing hatch spacing. The combination of PPs with an energy density of less than 75 J/mm³ is expected to yield the Af temperature below 37 °C. P = 80 W, v = 600 mm/s, and h = 70 μm were identified as the optimal combination because of a good tensile strength of 612 MPa and a peak shape recovery rate of 96.94%. Biocompatibility assessment showed that SLM-NiTi porous scaffolds supported pre-osteoblast survival and proliferation. A patient-specific mesh-like supporting prosthesis was designed to show the prospect of 4D-printed orthopedics implant. In clinical application, SLM-NiTi prosthesis could reduce bony window and facilitate easier insertion through compressive deformation.

Interaction between inclusions and the TRIP effect during tensile loading of an L-PBF 18Ni-300 maraging steel and effect on ductility

The influence of non-metallic inclusions on the tensile ductility of a direct aged 18Ni300 maraging steel produced by L-BBF was investigated on two materials having the same microstructure and a different content of non-metallic inclusions. The strain-induced transformation of austenite promotes the TRIP effect enhancing ductility. In the presence of a high amount of inclusions, the minimum strain needed to trigger strain-induced transformation is reached after necking, and the transformation cannot contribute to ductility. The effect of inclusions is to promote stress rising and strain accumulation, but mostly to make TRIP uneffective. To recover the effectiveness of TRIP and, in turn, increase ductility, the stability of reverted austenite should be reduced, in order to anticipate its transformation in martensite that is able to extend the uniform deformation step.

Thermal cycles, structure and properties of welded joints in structural steels during welding in extreme cold conditions

The article summarizes research on the thermal cycles, structure, and properties of welded joints made from low-alloy and low-carbon steels during arc welding in sub-zero temperatures. This review aims to analyze previous research to create solid recommendations for welding steel bridge structures during winter conditions. The results of a comparison of experimental measurements of thermal cycles of welding samples with different sizes made at room and subzero ambient air temperatures (down to minus 50 °C) are considered. It is shown that in small plates with dimensions of 200 × 250 × 10 mm, due to more intense heat reflection from the edges of the specimen, the thermal cycles of welding at different temperatures do not differ significantly. In more massive samples (sized 450 × 250 × 10 mm), an increase in the cooling rate of the overheated welded joint area is observed compared to room temperature welding. The impact of hydrogen on the development of cold cracks in low-alloy steels during welding at temperatures below freezing is examined. Metallographic analysis has revealed that the structural changes that occur during the welding of various steel grades are notably different and are influenced by the steel’s chemical composition as well as the thermal cycle parameters of the welding process. Dilatometric studies indicate that variations in the levels of alloying elements within different grades significantly influence the kinetics of austenite transformation. Therefore, to identify the best welding techniques for subzero temperatures, it is essential to consider not just how heat disperses in these conditions, but also the kinetics of phase changes and their effects on the structure and properties of the products resulting from austenite decomposition.

Numerical and Experimental Investigation of Austenite Transformation of Bearing Steel GCr15 in Non-isothermal and Isothermal Processes

Numerical and Experimental Investigation of Austenite Transformation of Bearing Steel GCr15 in Non-isothermal and Isothermal Processes

Effect of Electroslag Remelting on the Microstructure and Ballistic Penetration Characteristics of an Austenite‐Based Lightweight Steel

Herein, the effects of electroslag remelting (ESR) and impurities in ESR slag on the composition, microstructure, and properties of lightweight steel with a nominal composition in wt% of Fe‐20Mn‐10Al‐1.5C are studied. These results can provide a reference for the production of such steels using ESR and the design of the composition of such steels. The results show that ESR can make the contents of Si increase and that of S decrease, make the grain size decrease, make the phase transformation of austenite at about 540 °C change from spinodal decomposition to ordered transformation, make the contents of MnS and SiO2 and inclusions greater than 5 μm decrease, make the distribution of inclusions homogenize, and make the shape of inclusions change from long strip with sharp corners to spherical shape. ESR can improve its strength, plasticity, and antiballistic penetration properties.

A hot deformation constitutive model applicable for complete austenite and dynamic ferrite transformation interval

Dynamic ferrite transformation is a vital microstructure evolution mechanism for carbon alloy steels and an essential technology for manufacturing high-performance steel materials. In practice, carbon steel hot working processes are usually carried out at various temperatures, involving the evolutionary behavior of the single-phase austenite and the ferrite dynamic transformation process. Few models can simultaneously predict the microstructural state and deformation resistance in the single-phase austenitic interval and the dynamic ferrite transformation interval. The deformation mechanisms involve work-hardening, dynamic recovery, and dynamic recrystallization of austenite and ferrite phases, as well as the dynamic transformation of austenite to ferrite and coordinated deformation between the two phases. Therefore, this paper extends the application range of the model based on the viscoplastic unified constitutive model by considering the above deformation mechanisms. The constitutive model proposed in this paper applies to both the single-phase austenite interval and the dynamic ferrite transformation interval. Moreover, it can accurately predict carbon alloy steel's microstructure state and deformation resistance in different intervals. This paper can help to construct a hot deformation constitutive model in a wide range of deformation temperature intervals of steel materials.

Elastocaloric effect of NiTi shape memory alloys manufactured by laser powder bed fusion

To address the challenges posed by the complex processing of NiTi alloys, the additive manufacturing technology has been employed for the preparation of NiTi alloys samples. Up to now, there is limited research on the elastocaloric effects of NiTi alloys manufactured by LPBF. This study focused on the utilization of laser powder bed fusion (LPBF) to fabricate NiTi samples, with a particular emphasis on the influence of laser power, scanning speed and hatch spacing on the microstructure and properties of NiTi alloys. The results indicated that the process parameters affect the stress hysteresis of superelasticity by influencing the Ni content in the NiTi alloys. The higher Ni content, the lower the stress hysteresis. In addition, the critical stress for plastic deformation of the texture in the <001> direction in NiTi alloys is the smallest. When only the P was changed, the proportion of the texture in the <001> direction in the sample increased with the increase of P, the proportion of plastic deformation increased, and the degree of recovery also gradually decreased. Furthermore, at a specific temperature, 10 K higher than the end temperature of austenite transformation, each sample exhibited good superelasticity. In particular, the 1st cooling capacity of the sample with the best elastocaloric effect reached 11.0 K, which was superior to other results obtained by LPBF under similar compressive strain levels.

On Self-Positioning and Self-Fixation of Parts Made of Alloys with Shape Memory Effect under Component Assembling

Introduction Violation of mutual positioning and fixation of parts worsens the operation of the equipment. Traditional approaches to solving the problem under consideration have been sufficiently studied: interchangeability of parts and the use of special equipment. Both methods involve a significant number of additional elements and assembly operations. Fixation is often provided by means of force fitting and welding. Disadvantages of these methods include assembly, residual and other stresses, engineering constraints, etc. To solve these problems, alloys with thermoelastic phase transformations are used, which provide shape memory effects (SME) to manifest themselves. This article describes, for the first time, self-positioning and self-fixation using the example of parts specially made from an alloy with SME. Materials and Methods. The pin element under pressing mandrels the blind hole of the cup and enters the seat. The alloy with SME was Ti-55.7wt%Ni. The temperature of the onset of its austenitic transformation was As = 95°C ± 5°C. The elemental composition was determined by a Shimadzu EDX-8000 X-ray fluorescence spectrometer, the phase composition — by a Shimadzu XRD-7000 diffractometer. The temperature was specified through differential scanning calorimetry. The range was 20–300°C, the heating rate was 5 deg/min. A Guide T120 thermal imager and a RangeVision DIY 3D scanner with structured illumination were used. After pressing the pin into the cup at different angles, the alignment and deviations between the axes of the cup and the pin were examined. Then, the cup was heated to 110–120°C, cooled, and control measurements were taken.Results. Values of the deflection angle after pressing were 0.2–11°. With a rigid structure and an installation angle of 0°, the pin deflected in the mounting hole by 0.2–0.5°. The axes shifted and did not intersect. The pin was not always completely pressed in. This indicated uneven deformation of the metal and different stress values around the hole. Such a unit would soon fail. The pin took the required position after heating the cup to 110–120°C (this temperature was higher than at the end of the reverse martensitic transformation). The angular deviation of the axes was noted to be 0.03–0.1°. The maximum misalignment (0.04 mm) corresponded to high positioning accuracy. Heating during the reverse martensitic transformation created internal stresses that returned the initial geometry of the cup. They also formed the forces that positioned and fixed the pin in the hole. That is, it is the parts that provide positioning and fixation (this is selfpositioning and self-fixation).Discussion and Conclusion. For self-positioning and self-fixation of parts due to the shape memory effect, it is necessary to avoid sharp transition lines between the surfaces of parts during design, select rounded corners or fillets, and get a clean surface without burrs. Self-fixation and self-positioning reduce defects and inaccuracies during assembly. The use of certain alloys increases the profitability of equipment production.

Effect of Residual Stresses on the Fatigue Stress Range of a Pre-Deformed Stainless Steel AISI 316L Exposed to Combined Loading

AISI 316L austenitic stainless steel is utilized in various processing industries, due to its abrasion resistance, corrosion resistance, and excellent properties over a wide temperature range. The physical and mechanical properties of a material change during the manufacturing process and plastic deformation, e.g., bending. During the combined tensile and bending loading of a structural component, the stress state changes due to the residual stresses and the loading range. To characterize the component’s stress state, the billet was bent to induce residual stress, but a phase transformation to martensite also occurred. The bent billet was subjected to combined tensile–bending and fatigue loading. The experimentally measured the load vs. displacement of the bent billet was compared with the numerical simulations. The results showed that during fatigue loading of the bent billet, both the initial stress state at the critical point and the stress state during the dynamic loading itself must be considered. Analysis was demonstrated only for one single critical point on the surface of the bent billet. The residual stresses due to the phase transformation of austenite to martensite affected the range and ratio of stress. The model for the stress–strain behaviour of the material was established by comparing the experimentally and numerically obtained load vs. displacement curves. Based on the description of the stress–strain behaviour of the pre-deformed material, guidelines have been provided for reducing residual tensile stresses in pre-deformed structural components.

A comparative study of the microstructure and shape memory behaviour of NiTi, NiTiHf, and Pt-added NiTiHf alloys

The microstructure, substructure, transformation temperature, and recovery ratio of a novel Ni45Pt 5 Ti30Hf20 alloy are reported in the current work. The properties of binary TiNi and ternary TiNiHf alloys are also characterized to establish a comparative basis for shape memory behaviour. The microstructure of the cast structure of Ni45Pt5Ti30Hf20 alloy showed a dendritic matrix and interdendritic eutectic-like mixture, and that of the homogenized structure consisted of martensitic matrix and secondary phase of dark contrast having the composition (Ti+Hf)2(Ni+Pt). Pt substitution of Ni in the ternary alloy with 20 at.% Hf by 5 at.% leads to a decrease in the Af, As, Ms, and Mf . Ms and Mf represent the temperatures at which austenite to martensite transformation starts and completes, respectively, while As and Af represent the temperatures at which martensite to austenite transformation starts and completes, respectively. The XRD studies showed that the structure of martensite is B19′ and TEM studies showed that the substructure of martensite in Pt modified NiTiHf alloy is similar to that of ternary NiTiHf alloy. The shape memory recovery of the Pt-modified alloy is similar to the ternary alloy at higher strength levels. The recovery ratio determined using Vickers indentation is compared with that determined using compression tests to provide an efficacy of small volume tests for screening of these alloys.

Microstructure Evolution and Tensile Properties of Medium Manganese Steel Heat Treated by Two-Step Annealing

In this paper, the nucleation and growth of austenite are controlled through a two-step annealing process to achieve multi-scale distribution and content increase of retained austenite in low manganese series medium-Mn steel. Combining SEM, EBSD, AES, and other experimental equipment, the evolution rules of the microstructure, properties, and element distribution behavior of the test steel during the annealing process are studied. Compared with one-step annealing, the two-step annealing significantly broadens the size distribution range of retained austenite. In the first step, after annealing at a higher intercritical temperature (760 °C), the ferrite and the M/A island are obtained, completing the initial partition of Mn and the refinement of microstructures. During the second step of annealing (720 °C), the primary Mn-rich martensite region provides higher nucleation driving force and finer dispersed nucleation sites, promoting the nucleation and growth of reverse transformation austenite. At the same time, the metastable-retained austenite formed after the first step of annealing continues to grow through interface movement. Furthermore, a high proportion (23.4%) of retained austenite with multi-scale distribution is formed in the final microstructure, and the product of strength and elongation increased from 21.8 GPa·% by the one-step annealing process to 30.1 GPa·%.

Effect of microstructural inheritance window on the mechanical properties of an intercritically annealed Q&P steel

Different initial microstructures significantly influence the final microstructures and mechanical properties of the intercritically annealed quenching and partitioning steels. Previous studies have primarily focused on the mechanism for the inheritance of different initial microstructures into the final microstructures, which affects the phase fraction and mechanical properties. However, these studies have overlooked the existence of an inheritance window in the intercritical annealing process. In this study, we investigated the inheritance window and explored the impact of varying initial microstructures on the reverse transformation of austenite, final phase fraction, and mechanical properties. Our findings reveal that the varying initial microstructure exhibits minimal influence on the final microstructure and mechanical properties for short or long annealing times. However, for the intercritical annealing treatment for 60 s, the initial microstructure of martensite with more nucleation sites accelerated the austenite reverse transformation fraction, enhanced the reverse-transformed austenite content, increased the primary martensite content, and improved the yield strength. Conversely, the coil-cooled sample, with initial microstructures consisting of ferrite and pearlite without dissoluble Mn-rich cementites, reduced the austenite reverse transformation rate, decreased the reverse-transformed austenite content, enhanced the ferrite and RA content, and improved ductility.

Effect of dislocation density on microstructure and mechanical properties of cold-rolled medium Mn steel

This study investigated the effect of dislocation density on microstructural transformation and mechanical properties of Fe-7.23Mn-4.42Al-0.09C-1.99Si (wt.%) steel. By the tempering treatment, the dislocation density was reduced. The effect of of dislocation density on the plasticity of the steel was analyzed. The dislocation density was reduced from 2.3 × 10−16 m−2 to 1.6 10−16m−2 by tempering. Reducing dislocation density in the metastable austenite resulted in a higher metastable austenite transformation rate. And the low dislocation density steels exhibited a longer strain length during tensile deformation. It was obvserved that the dislocation density of the test steel decreased by 30% after tempering, the austenite transformation rate increased to 53.3%, and tensile strength and elongation increased to 1010 MPa and 44% respectively.

Precipitation kinetics of ferritic / martensitic oxide dispersion strengthened steels: Influence of the matrix phase transformation

ODS steels are candidate materials for the future generation of nuclear power plants. Ferritic / Martensitic (F/M) ODS steels display better formability thanks to high temperature austenitic transformation. The precipitation kinetics of a F/M Fe‑9Cr ODS steel during powder consolidation up to 1100 °C has been characterized by in‑situ Small Angle X-ray Scattering (SAXS). The influence of the matrix phase transformation has been established, showing an increase of the growth rate of the nano‑oxides in austenite, leading to nano‑oxides ∼ 2x larger in diameter than in Fe‑14Cr ferritic ODS grades at the end of the thermal treatment. These results are further supported by local atom probe tomography (APT) performed across grains showing contrasted microstructure and composition. Anomalous SAXS as well as comparison between APT and SAXS provide evidence that the nano‑oxides stabilize with a Y2Ti2O7 or Y2TiO5 stoichiometry around 1100 °C.

Thermo-kinetic insights into deformation mechanism in the phase-transforming nanostructured Fe alloy

Solid-state phase transformations (SSPTs) being the most widely versatile routes to tailor microstructures are less utilized in the design of nanostructured (NS) alloys, resulting in a lack of understanding of the significance of SSPTs in tuning mechanical properties. Here, we combine nanostructuring with reverse austenite transformation to make a phase-transforming NS Fe alloy consisting of ultrafine ferrite and austenite grains. By comparison with the coarse-grained (CG) counterpart, the NS sample exhibits high strengths (i.e., the yield and the ultimate tensile strengths are 816 and 1170 MPa, respectively), good ductility with a uniform elongation of 53 %, and superior strain hardening capacity, under multiple strengthening mechanisms and the activation of transformation induced plasticity. Regarding the mechanism in forming the NS sample, grain refinement is revealed to markedly affect the austenite formation kinetics by generating sluggish growth behavior accompanied by sufficient solute partitioning. Then, we clarify the difference in mechanical responses of the phase-transforming NS and CG samples using a physically based microstructures-properties model. Further based on the thermo-kinetic theory of generalized stability, we show that the simultaneous increase of strength and ductility in the NS sample relative to the CG sample is originated from the deformation physics with higher driving force and higher generalized stability. From the thermo-kinetic perspective, our work demonstrates that the SSPTs hold substantial promise in optimizing the microstructures and the mechanical properties of NS Fe alloys and are expected to find wide application in the development of other NS materials.

Effects of intercritical annealing time on microstructure, tensile properties, and cryogenic toughness of newly designed ultra-low C low Ni Medium-Mn steel

An ultra-low carbon and low nickel medium manganese heavy steel plates was fabricated by quenching and intercritical annealing process. The effect of annealing time on the tensile properties and impact toughness were studied in relation to the formation of reversed transformation. The results show that excellent mechanical properties with yield strength of 680 MPa, tensile strength of 871 MPa, total elongation of 38.2% and high impact energy of 187 J at −60 °C were obtained. The microstructure comprised of ultra-fine grained ferrite and retained austenite (RA) together with a small amount of martensite after intercritical annealing. Increasing the intercritical annealing time resulted in coarser matrix microstructures, larger and more voluminous retained austenite, but with notably reduced stability. Highly stable RA enhances the work hardening capacity of the steel via sustained deformation-induced transformation (TRIP effect), significantly contributing to the toughening of the multiphase system. In addition, Austenite stability, rather than large-angle grain boundaries and the amount of austenite transformation, is the primary factor determining the low-temperature toughness of medium manganese steel.

Austenite formation and solute redistribution during double soaking of a 7Mn-steel

In this work, the influence of secondary soaking parameters on microstructural evolution in medium manganese steels is evaluated with a specific focus on the mechanisms driving austenite formation and solute partitioning at an intermediate secondary soaking temperature of 750 °C. The secondary soaking heat treatment represents the latter step of the double soaking heat treatment where it is used, after an initial intercritical annealing heat treatment, to form additional, solute-lean austenite. Here, data are obtained on a 0.14C-7.17 Mn steel for secondary soaking temperatures between 700 °C and 800 °C, and for times up to 1200 s. Austenite formation during secondary soaking is characterized using dilatometry and XRD, while Mn redistribution is experimentally observed using STEM-EDS. Manganese partitioning during secondary soaking, as well as calculated changes in carbon partitioning, are further explored through a DICTRATM model. Experimental and simulation results suggest that the ferrite-to-austenite transformation during the secondary soaking step may proceed under a partitioning, diffusional transformation at the 750 °C secondary soaking temperature. Manganese partitioning was demonstrated to primarily occur from ferrite to newly formed secondary austenite, while carbon diffusion principally occurred from primary to secondary austenite. Transformation of secondary austenite to martensite upon quenching along with some fraction of primary austenite, whose transformation was attributed to a reduction in C concentration, was shown demonstrated. The results of this study are expected to be of interest to those seeking to design multi-step heat treatments which produce austenite of variable solute concentrations and stabilities.