TM Modes Research Articles

Substrate integrated waveguide differential antenna for full duplex applications

Abstract This paper presents a substrate-integrated waveguide (SIW) differential antenna for full duplex applications. The proposed antenna consists of two square SIW cavities named as outer and inner. The inner cavity is nested into the outer cavity. The outer cavity is differentially excited with a pair of coaxial feed lines, while the inner square patch is orthogonally excited with another pair of differential coaxial feed lines. This orthogonal feeding arrangement results in high isolation between the differential ports. The modified hybrid TE130/310 mode of the outer cavity radiates through a pair of arc-shaped slots at 9.35 GHz, while the TM01 mode of the inner square patch is responsible for the radiations at 8.65 GHz. The proposed antenna prototype is fabricated and measured for validation. Moreover, the designed antenna has a front-to-back ratio better than 22 dB and measured maximum gain values of 6.1 dBi and 7.6 dBi at 8.65 GHz (Port 2 ON) and 9.35 GHz (Port 1 ON), respectively.

Plane wave diffraction by a semi‐infinite parallel‐plate waveguide with partial material loading: The case of H polarisation

AbstractThe analysis of diffraction by a semi‐infinite parallel‐plate waveguide with partial material loading is rigorously carried out using the Wiener–Hopf technique for the H‐polarised plane wave incidence. In solving the Wiener–Hopf equations, the authors apply the Modified Residue Calculus Technique (MRCT) to achieve highly accurate solutions. The scattered field in real space is explicitly derived by performing the inverse Fourier transform of the solution in the transform domain. Within the waveguide, the scattered field is represented in terms of the waveguide TM modes, while the external field is asymptotically evaluated by applying the saddle‐point method to yield a far field expression. The authors present representative numerical examples of the radar cross section for various physical parameters and discuss the far‐field scattering characteristics in detail. Comparisons with the E‐polarisation are also given.

Ultra-broadband absorber and perfect thermal emitter for high-efficiency solar energy absorption and conversion

This study proposes a pyramid-shaped solar absorber designed with multi-layered Ti-SiO2 ring stacked. The structure achieves an average absorption efficiency of 98.03 % over the range of 280–4000 nm, and under AM1.5 spectral conditions, the weighted average absorption efficiency reaches 97.66 %, the bandwidth with an absorption efficiency greater than 90 % reaches 3750 nm. To explore the reason for achieving ultra-broadband absorption with this structure, the electromagnetic field distribution at three absorption peaks was calculated. The results revealed that the resonance between the polarization direction of the three-layer circular ring stacked structure and the plasmon resonance at the junction of Ti and SiO2 contribute to the model's capability for ultra-broadband high-efficiency absorption. At the same time, the thermal emissivity of the structure was calculated at high temperatures of 1000 K and 2000 K, both exceeding 97 %. Furthermore, due to the fully symmetrical design, the absorber is polarization-independent. It was found through calculations that whether in TM mode or TE mode, as the incident angle varies from 0° to 60°, the average absorption efficiency of the absorber changes only by 11.16 %, thereby verifying the structure's excellent insensitivity to incident light angles. In summary, all these characteristics indicate that the model has excellent application prospects in fields such as solar energy collection and photothermal conversion.

Inverse-Designed Ultra-Compact Passive Phase Shifters for High-Performance Beam Steering.

Ultra-compact passive phase shifters are inversely designed by the multi-objective particle swarm optimization algorithm. The wavelength-dependent phase difference between two output beams originates from the different distances of the input light passing through the 4 μm × 3.2 μm rectangular waveguide with random-distributed air-hole arrays. As the wavelength changes from 1535 to 1565 nm, a phase difference tuning range of 6.26 rad and 6.95 rad is obtained for TE and TM modes, respectively. Compared with the array waveguide grating counterpart, the phase shifters exhibit higher transmission with a much smaller footprint. By combining the inverse-designed phase shifter and random-grating emitter together, integrated beam-steering structures are built, which show a large scanning range of ±25.47° and ±27.85° in the lateral direction for TE and TM mode, respectively. This work may pave the way for the development of ultra-compact high-performance optical phased array LiDARs.

Cavity-based bunch length measurement study for the Super Tau-Charm Facility transport line

In this paper, a nondestructive cavity-based scheme is proposed to achieve high-resolution bunch length measurement in the Super Tau-Charm Facility (STCF) transport line. By extracting the TM010 and TM020 mode signals excited by the beam within a single pillbox cavity, a beam spectrum can be obtained to deduce the Root-Mean-Square (RMS) bunch length. This scheme is more spatially compact compared to the traditional method using double cavities. In this study, the basic principles of the cavity-based bunch length measurement method are explained, the monitor layout is introduced, and the design methods for the cavity and electronics are described. A prototype cavity was machined. Offline tests demonstrate that the eigenmodes in the cavity meet the design requirements and can be used for the bunch length measurements. Based on the online signal characteristics of the Cavity Beam Position Monitors (CBPMs) and the beam parameters of the STCF, the performance of this measurement method is evaluated. For picosecond-level bunches in the STCF transport line, this scheme can provide a bunch length measurement resolution of 233.5 fs at 1.5 nC.

Design of an optically transparent ultrawideband absorber with high angular stability using ITO films.

In this paper, an optically transparency ultrawideband absorber with high angular stability is designed. The proposed absorber is composed of two different materials with indium thin oxide (ITO) conductive films and polydimethylsiloxane (PDMS) substrates. With the aid of a stacked structure design, the absorber has a 90% absorption band from 5 to 43.5 GHz and the fractional bandwidth reaches 158.7%. Also, for the TE mode, the absorption remains stable with the oblique incident angles reaching 50°. And similar angular stability can be observed for the TM mode from 0° to 70°. Besides, the thickness of the absorber is only 0.092 wavelength and transmittance within the visible band is 57.3%. For further verification, a prototype is fabricated and measured. Good agreements between the simulated and the measured results can be observed.

Design of tunable terahertz metamaterial for variable optical attenuation and sensing applications

In this work, an actively tunable terahertz metamaterial (TTM) is proposed to realize variable optical attenuation and sensing applications. The unit cell of TTM is composed of H-shaped resonator (HSR) and C-shaped resonator (CSR). The resonant frequency can be tuned from 0.60 THz to 0.82 THz and show an analog electromagnetically induced transparency (EIT) phenomenon. By adjusting the geometry parameters of HSR and CSR, the enhanced quality (Q) factor is obtained from 2 to 14. Moreover, the CSR can be rotated from 0° to 90° to show the potential in the variable optical attenuator (VOA) application. The resonant intensity at 0.60 THz can be gradually decreased and then disappeared eventually when the CSR rotated from 0° to 90° in TE mode. While the resonant intensity at 0.60 THz can be gradually increased and then reach maximum value from 0° to 90° in TM mode. To demonstrate the proposed TTM can be used for the environmental sensing application, the TTM is exposed on the ambient environment with different refractive indexes from 1.0 to 2.2. The maximum sensitivity is 67 GHz. This work offers a novel approach for the THz metamaterial using for the VOA, optical switching, and sensing applications.

Compact polarization splitter-rotator based on lithium niobate-on-insulator platform

We propose a compact mode-coupled polarization splitter-rotator (PSR) based on the lithium niobate-on-insulator platform. The PSR is composed of an asymmetric directional coupler, a taper, and an S-bend. Cross-polarization mode coupling is achieved using a ridge waveguide and air cladding to break the symmetry of the waveguide cross section with a length of only 61 μm. Simulation results show that the insertion losses of this device in the 1500–1600 nm range are less than 1.85 and 0.31 dB for TM0 and TE0 modes, respectively, and the extinction ratios are more than 22.5 and 22.7 dB, respectively. In addition, the PSR exhibits a polarization conversion efficiency of 99.97% at 1550 nm. The proposed PSR has great potential for applications in polarization-division multiplexing transmitters and on-chip polarization controllers.

Cyclotron resonance imaging at cryogenic temperatures enabled by electric field modification in a microwave cavity

Abstract Cyclotron resonance (CR) is a standard but emerging technique for investigating carrier properties of semiconductors. We have succeeded in CR measurements by employing a microwave cavity designed for electron paramagnetic resonance (EPR). Here, we demonstrate CR imaging to visualize the spatial distribution of carriers at cryogenic temperatures for the first time. To realize CR imaging, it is necessary to account for the electric field modification in the microwave cavity of a cylindrical TM110 mode, which is designed for EPR imaging and is inherently unsuitable for CR measurements. CR detection requires the oscillating electric field perpendicular to the external static magnetic field (B 0) at the sample position, which is not designed for the unloaded cavity. It has been challenging to verify the electric field distribution inside the cavity experimentally, but we show that the observation of the CR signals provides evidence of modification in the electric field. Analysis of the electromagnetic field explains the results, revealing a field distribution whose strength and direction are perturbed due to the lensing effect by the inserted dielectric materials.

Design of a switchable triple-waveguide-based TE-converted polarization beam splitter based on lithium niobate

The lithium-niobate-on-insulator (LNOI) platform has been the new force to drive the developments of integrated photonics, where efficient polarization management and mode conversion are the fundamental issues to be solved. In this work, we proposed a switchable TE-converted polarization beam splitter (PBS) based on optical phase change material (PCM) and a triple-waveguide in simulation. To optimize and analyze the proposed design, the 3D finite difference time domain (3D-FDTD) method is applied in this work. The simulated results indicate that when PCM is in the amorphous state, the device can effectively separate the TM and TE modes, achieving a low insertion loss (<0.5dB) for both modes at 1550 nm. While the PCM is in the crystalline state, the proposed device can realize the efficient conversion from the input TE0 mode to output TE1 mode, which obtains a mode conversion efficiency of 99.5%, crosstalk of −26dB, and insertion loss of 0.5 dB at 1550 nm. We hope such a device can make compact integration and capacity improvement for the integrated photonics in LNOI.

Transverse magnetic supermodes in plasmonic optical fibers excited by radially polarized light

The overlap integrals method, with a fully vectorial formulation, is used to model the selective excitation of the TM01 mode in a few-mode optical fiber with a radially polarized donut beam, and its coupling to guided modes having a plasmonic character (supermodes). The analyses were performed on a waveguide formed as a step-index few-mode optical fiber coated with a thin gold film, at an operating wavelength of 1310 nm. The waveguide was found to support modes having optical fiber, circular metallic waveguide, and surface plasmon characteristics, depending on geometrical and material parameters. Three purely bound transverse magnetic (radially polarized) supermodes were identified: Two symmetric, labeled sTM01 and sTM02 modes, and one asymmetric, labeled ab mode, where symmetry pertains to the transverse electric field distribution over the gold film. The effective mode indices of the supermodes were studied as a function of the thickness of the gold film and its proximity to the fiber core. Considerations for the selective excitation of the sTM01 mode are discussed along with its possible applications. The transmittance of the supermodes is found to be robust even at sharp waveguide transitions. The results predict that effective excitation of TM supermodes with strong plasmonic character, without significant coupling losses, can be achieved by exciting the fiber with a radially polarized donut beam.

Ultra-broadband polarization-insensitive versatile solar thermal harvester

Sustainable and Renewable Energy is essential because it's non-polluted and available in nature. Solar energy is the most important of them all as its the essential of them all. Sun energy is a clean and finest alternative to renewable energy sources. The slotted cylinder-shaped Mxene-based resonator solar absorber (SCMRSA) achieved an average of 95.06 % efficient absorption. The MXene material is used as a resonating material above the titanium oxide layer based on the MXene layer. The wide angle of incidence is achieved which is analyzed by changing the different angles of incidence. The E-field response is also observed for the TE and TM modes. The results show a similar response for both TE and TM modes. The optimization of the structure is also observed for different variable variations and the final optimized design is used for the highly efficient absorptance results. The SCMRSA is also applicable for various solar thermal applications and energy harvesters.

Wideband circularly polarized dielectric resonator antenna with multi-functional metasurface assistance for low profile

ABSTRACT A low-profile broadband circularly polarized (CP) dielectric resonator antenna (DRA) is proposed, utilizing DR reutilization and metasurface (MS) techniques. Two resonant frequencies and an AR minimum are achieved simultaneously, by exciting a rectangular DR with an inclined corner-truncated coupling slot, for it generates nearly degenerated TE111 modes. For significant bandwidth enhancement and low profile, a new resonator is formed by reusing the DR and loading an MS above, which works in orthogonal TM modes. To increase the axial ratio bandwidth (ARBW) further without enlarging the antenna size， two parasitic patches are printed on two adjacent side walls of the DR. To verify the rationality and feasibility, the antenna is fabricated and measured. The fabricated prototype possesses the profile of 0.06λ 0 (λ 0 is the free-space wavelength at the center frequency). The measured impedance bandwidth (IBW) and ARBW are 36.05% (4.23 ~ 6.09 GHz) and 22.46% (4.9 ~ 6.14 GHz), respectively. The proposed antenna has both broadband characteristics and a low profile, making it easy to integrate into space-limited wireless communication systems with high data rates.

Electromagnetic field compensation to attenuate energy leakage in TM020 mode damped cavity

This paper discusses the TM020 mode Higher-order Mode (HOM) damped cavity, which has a higher quality factor and lower characteristic impedance than the conventional TM010 mode. The unique electromagnetic field (EMF) distribution of the TM020 mode allows for an absorber to be placed at the magnetic field wave node, protecting the working mode while suppressing the HOMs. However, the introduction of high power input couplers and other structures can cause an asymmetrical EMF distribution, leading to operating mode leakage.To address this, EMF compensation methods are applied to the high power input coupler to achieve symmetrical EMF distribution, reducing operating mode loss. Overcoupling of the high power input coupler and the resonant cavity can significantly affect local EMF distribution, causing TM020 mode asymmetry. A tab structure at the coupler port are used to compensate for coupler-induced perturbations, attenuating EMF leakage.The paper proposes electromagnetic compensation structure schemes to mitigate working mode EMF leakage. The reliability of the scheme is demonstrated by the analysis of radiofrequency performance and other aspects through simulation software.

2D Magnetotelluric Resistivity Structure Modeling Using Finite Element Method Based on Vector Triangular Grid and Its Application to Lembang Fault MT Data

Abstract Magnetotellurics is one of the geophysical exploration techniques that relies on the natural fluctuations of electromagnetic waves to delineate their influence on the Earth. The primary focus of this method is to reveal the structure of Earth’s subsurface with the value of resistivity. The application of numerical approaches in magnetotelluric modeling has proven to be an efficient method in various theoretical studies in the field of geophysics, particularly in the context of modeling two-dimensional structures. This research explains a 2D resistivity structure modeling using a vector finite element method. This approach utilizes the edges of elements as vector bases. The presented results include response values such as apparent resistivity and impedance phase at the surface. The study employs the standard model from COMMEMI as a reference to validate the modeling program. Furthermore, the results from this modeling program are compared with the outcomes of the modeling program developed by Weaver et al. The good results were obtained with error values for each model for layered and homogeneous Earth < 3%. Additionally, for the reference model COMMEMI, errors of 3.4393% and 1.4050% were obtained for TE and TM modes, respectively. Furthermore, apparent resistivity and impedance phase results closely approximated the reference values for the topography model. Subsequently, in the application to field data, specifically the Lembang Fault, errors were obtained for the TE and TM modes within the range of 1.16 – 9.16% for each MT data acquisition site.

Electromagnetic scattering from a truncated semicircular slot for TM mode

Electromagnetic scattering from a truncated semicircular slot for TM mode

Factorized form of the dispersion relations of a traveling wave tube

The traveling tube (TWT) design in a nutshell comprises of a pencil-like electron beam (e-beam) in vacuum interacting with guiding it slow-wave structure (SWS). In our prior studies the e-beam was represented by one-dimensional electron flow and SWS was represented by a transmission line (TL). We extend in this paper our previously constructed field theory for TWTs as well the celebrated Pierce theory by replacing there the standard TL with its generalization allowing for the low frequency cutoff. Both the standard TL and generalized transmission line (GTL) feature uniformly distributed shunt capacitance and serial inductance, but the GTL in addition to that has uniformly distributed serial capacitance. We remind the reader that the standard TL represents a waveguide operating at the so-called TEM mode with no low frequency cutoff. In contrast, the GTL represents a waveguide operating at the so-called TM mode featuring the low frequency cutoff. We develop all the details of the extended TWT field theory and using a particular choice of the TWT parameters we derive a physically appealing factorized form of the TWT dispersion relations. This form has two factors that represent exactly the dispersion functions of non-interacting GTL and the e-beam. We also find that the factorized dispersion relations comes with a number of interesting features including: (i) focus points that belong to each dispersion curve as TWT principle parameter varies; (ii) formation of “hybrid” branches of the TWT dispersion curves parts of which can be traced to non-interacting GTL and the e-beam.

Designing Tb-doped Mn-Ni-Cu ferrite meta-absorbers for a broad frequency range: Magnetodielectric, physical, reflection loss, and absorptivity characteristics

Developing meta-absorbers with exceptional EM wave absorption, shielding capacity, and superior dissipation performance remains worthwhile in the gigahertz (GHz) range. Electromagnetic pollution has a detrimental impact on the health of living organisms due to the emergence of high-frequency waves from communication devices. The challenges were addressed by preparing, designing, and simulating ferrite-based meta-absorbers. The nanoferrites of Tb-doped Mn-Ni-Cu (Mn0.2Ni0.3Cu0.5TbxFe2-xO4) with different levels of Tb (x = 0.00, 0.025, 0.05, 0.075) were prepared utilizing the sol-gel auto combustion technique. The phase, structural, elastic, and magnetic features of the Tb-doped Mn-Ni-Cu ferrites were examined using XRD, FESEM, FTIR, and VSM techniques, respectively. The MAUD software was utilized to obtain refinement and precise structural characteristics. The force constant, phase, and elastic properties were also assessed. The magnetization and coercivity exhibited a reduction. An assessment was conducted on the performance of field switching and high-frequency response. At high frequencies, the dielectric characteristics, such as complex permeability and permittivity, exhibit greater values, while losses diminish. At a frequency of 4.6 GHz, a reflection loss (RL) of −54.21 dB was measured for x = 0.05, whereas a reflection loss of −54.03 dB was measured for x = 0.075. The meta-absorbers of Tb-doped Mn-Ni-Cu ferrites were designed and simulated. The absorptivity of the Tb-doped Mn-Ni-Cu ferrite substrate material is illustrated. The meta-absorber exhibited three distinct absorption peaks at frequencies of 1.5, 2.5, and 4.5–6 GHz, respectively. The absorptivity of the material likewise rises with an increase in the incidence angle; the material's absorptivity also increases. The TM mode exhibited the highest values at an angle of 60 degrees, while the TE mode displayed the highest values at an angle of 0 degrees. Tb-doped Mn-Ni-Cu ferrites are effective for electromagnetic interference (EMI), multilayer ceramic integrated circuits (MLCIs), shielding, and absorbing high-frequency signals in 5 G applications.

Ultrathin metal-dielectric planar interface for high-performance photonic spin Hall effect

Abstract This study explores the photonic spin Hall effect (PSHE) with a focus on its sensitivity to incident wave polarization and physical parameter variations. Traditionally surface plasmonic resonance (SPR) systems mainly enhance H-polarized PSHE. However, our proposed method involves an ultrathin metal layer, capped with a glass dielectric layer on a glass substrate, to achieve high-performance PSHE for both H- and V-polarization waves. This high-performance PSHE in terms of enhancement in PSHE magnitudes arises from the simultaneous presence of SPR and waveguiding effects, resulting in the emergence of hybrid TE and TM modes. Investigating Au and Ag ultrathin metal layers, we find that the highest H-polarized PSHE occurs at ~1.52 × 10^6 nm and ~2.05 × 10^5 nm for Au and Ag, respectively. Similarly, for Vpolarized incident light, maximum enhanced PSHE is observed at ~1.58 × 10^5 nm and ~9.48 × 10^4 nm for Au and Ag, respectively. By adjusting the thickness of the metal and/or glass cap layer, precise control over PSHE amplitude and active polarization response is achievable. This research unveils unique capabilities for generating hybrid modes that enhance PSHE for both polarizations, offering a potential platform for developing tunable polarizationfavorable spin optics optoelectronic devices.

Compact and low-crosstalk multimode waveguide crossing utilizing subwavelength holey metamaterial waveguides

To further increase the transmission capacity of on-chip optical communication systems, hybrid division multiplexing technology has emerged as a crucial alternative solution, in which multimode waveguide crossings are highly desired. In this paper, we propose and experimentally demonstrate a compact multimode (i.e., three different modes) waveguide crossing that employs subwavelength holey metamaterial waveguides (SHMWs). The used SHMW, formed by inserting subwavelength periodic holes into a multimode interference (MMI) coupler, deservedly exhibits synergetic advantages of the two kinds of structures, enabling an attractive three-mode (e.g., TE0, TM0, and TM1) waveguide crossing with flexible design, small size, and good performance. Simulation results show that the realized device has a low insertion loss (< 0.74 dB), low reflection loss (<−13.1 dB), and low crosstalk (<−31.6 dB) at a central wavelength of 1550 nm for all the modes with a compact footprint of 27.4 µm × 27.4 µm. The experimental results prove that insertion losses are as low as 0.72 dB, 0.27 dB, and 0.90 dB for TE0, TM0, and TM1 mode, respectively, with the corresponding crosstalk below −38 dB at 1550 nm. The proposed device can be widely applied in photonic integrated circuits to construct photonic systems with the abilities of mode control and multiplexing.