Three-phase Four-leg Voltage Source Converter Research Articles

Experimental Validation of an Advanced Load-Shift System Operating as Shunt Active Power Filter

This paper presents a load-shift system with advanced functionalities for the power grid. When compared with the conventional approach, an advanced load-shift system allows the compensation of power quality problems on the power grid side, namely problems related to current harmonics, current imbalances, and low power factor. The advanced load-shift system is composed by a bidirectional ac-dc converter to interface the power grid and by a bidirectional dc-dc converter to interface an energy storage system. Since the main innovation is related with the power grid interface, the focus of this work is on the analysis of the ac-dc converter, which is based on a three-phase four-leg voltage source converter. A theoretical study and the details concerning the control algorithm are presented and discussed along the paper. A laboratory prototype of the advanced load-shift system was developed, and the main details of implementation are described in the paper. Experimental results obtained with the developed prototype prove that the advanced load-shift system contributes for the technology progress in this area, validating a new operation concept concerning the power quality on the power grid side. For all the operation modes, the system operates with high power factor and the currents on the power grid side are balanced with a low total harmonic distortion and in phase with the respective power grid voltages.

AC Current Ripple Harmonic Pollution in Three-Phase Four-Leg Active Front-End AC/DC Converter for On-Board EV Chargers

Three-phase four-leg voltage-source converters have been considered for some recent projects in smart grids and in the automotive industry, projects such as on-board electric vehicles (EVs) chargers, thanks to their built-in ability to handle unbalanced AC currents through the 4th wire (neutral). Although conventional carrier-based modulations (CBMs) and space vector modulations (SVMs) have been commonly applied and extensively studied for three-phase four-leg voltage-source converters, very little has been reported concerning their pollution impact on AC grid in terms of switching ripple currents. This paper introduces a thorough analytical derivation of peak-to-peak and RMS values of the AC current ripple under balanced and unbalanced working conditions, in the case of three-phase four-leg converters with uncoupled AC-link inductors. The proposed mathematical approach covers both phase and neutral currents. All analytical findings have been applied to two industry recognized CBM methods, namely sinusoidal pulse-width modulation (PWM) and centered PWM (equivalent to SVM). The derived equations are effective, simple, and ready-to-use for accurate AC current ripple calculations. At the same time, the proposed equations and diagrams can be successfully adopted to design the conversion system basing on the grid codes in terms of current ripple (or total harmonic distortion (THD)/total demand distortion (TDD)) restrictions, enabling the sizing of AC-link inductors and the determination of the proper switching frequency for the given operating conditions. The analytical developments have been thoroughly verified by numerical simulations in MATLAB/Simulink and by extensive experimental tests.

Voltage Control of Four-Leg VSC for Power System Applications With Nonlinear and Unbalanced Loads

Voltage source converters are presented as the key devices for the future massive integration of distributed renewable energy resources in the network. This article presents a novel approach to control a three-phase four-leg voltage source converter for grid-forming operation. The objective of the controller is to generate a balanced three-phase voltage with a given amplitude and frequency at the point of common coupling. The proposed control algorithm works over the stationary axes. It is based on full state feedback law in combination with a resonant control loop tuned at the fundamental frequency in order to guaranty zero steady-state error on the voltage. The main advantage of the controller with respect to the classical cascade controllers is that this strategy is not modified depending on the type of load connected at the point of common coupling. Moreover, a systematic methodology to compute the controller gains is presented by solving an linear quadratic regulator problem that considers an extended model. This method guarantees small signal stability and provides active damping to the system. A laboratory testbed with different type of loads is used to validate and compare the proposed algorithm with the classical one. The experimental results demonstrate the effectiveness of the proposal by achieving low levels of harmonic distortion and imbalances in steady-state as well as a fast transient response.

Control Method of the Three-Phase Four-Leg Shunt Active Power Filter

This paper presents a novel all-digital approach applied to three-phase four-wire active power filter (APF), which is made up of three-phase four-leg voltage source converters. The controller just detects the main current and DC side capacitor voltage. Calculation method of the switch duty cycle is deducted on the base of mathematics model formed. This controller has fewer measurement, higher robustness and simpler calculation as comparing to traditional controllers. Simulation verify that the APF with proposed controller can compensate the harmonics effectively.

Current Regulation in Four-Leg Voltage-Source Converters

Three-phase four-leg voltage-source converters by virtue of the fourth leg connected to the neutral points of the wye-connected loads effectively handle the zero-sequence currents and voltages occasioned by connected load impedance imbalances and/or nonlinearity of loads. This paper develops a generalized carrier-based pulsewidth-modulation scheme for this converter which with a natural reference-frame control scheme that directly controls the actual load currents ensures current regulation irrespectively of the nature of the load. The proposed modulation and control schemes are effectively validated by computer simulation and experimental results for the converter operation in the linear and overmodulation regions.

A carrier-based PWM method for three-phase four-leg voltage source converters

In this paper a voltage modulation method based on a triangular carrier wave for the three-phase four-leg voltage source converter is described. The four-leg converter can produce three output voltages independently with one additional leg. The proposed modulation method for the four-leg converter can be implemented with a single carrier by a simple but useful "offset voltage" concept. The method is equivalent to the so called three-dimensional space vector PWM method, but its implementation is much easier. The maximum magnitude of the balanced three-phase voltage and the maximum magnitude of zero sequence voltage, which can be synthesized simultaneously, are derived. The feasibility of the proposed modulation technique is verified by computer simulation and experimental results. These results show that a proposed carrier-based pulsewidth modulation (PWM) technique can be easily implemented without conventional computational burden.