Thin Layer Research Articles

Effect of carbide refinement on high temperature erosive wear behavior of high chromium white cast iron with different titanium and carbon additions

It is known that better erosion wear resistance of high chromium (27wt.% Cr) white cast iron (HWCI) with titanium (Ti) addition can be achieved by controlling the size of M7C3 carbides. Nevertheless, it might not be directly applicable to high temperature conditions due to the more complex factors involved, especially the hot oxidation behavior. Therefore, the effect of 0-2wt.% Ti and 3-4wt.% carbon (C) addition on the high temperature erosion wear behavior of HWCI has be investigated in this research. The results show that there are TiC and M7C3 carbides precipitated in the material matrix. The size of M7C3 carbides decreases drastically as the amount of Ti increases. On the contrary, it is effectively enlarged with the addition of higher C. In addition, there is no significant difference in hardness among all specimens due to the relatively similar carbide volume fraction (CVF). The wear resistance of HWCI is improved by increasing the amount of Ti although it has a lower value as the C content increases. It means that hardness is not an important factor in evaluating the wear characteristics of HWCI at high temperatures. The worn surfaces and cross-sections show that the smaller M7C3 carbides are more likely to undergo plastic deformation rather than being directly peeled out. In addition, the effect of hot oxidation behavior was negligible because there is only a very thin oxidation layer on the worn surface. Therefore, it can be concluded that the erosive wear behavior of the material is greatly influenced by the size of M7C3, which the material with better erosive wear resistance contains finer carbides.

Nonlinear flow of couple stress fluid layer over an inclined plate

The issue of stability of a thin couple-stress liquid layer flows on an inclined plane was inspected. The thin-film approximation was employed to obtain a Benney-like differential equation, that described the time record of the interface profile The linear transition state and reduction ratio of maximum classical (Newtonian) growth-rate were discussed. The complete evolution equation was solved numerically using the method of lines in order to support the novelty of the work. The linear stability could be enhanced by increasing the couple-stress coefficient and surface tension as well as reducing the inclination. However, the ordinary viscosity played an irregular role. The linear results predicted conditions (windows) in which the non-Newtonian film was more stable than its Newtonian counterpart. The nonlinear stimulation anticipated the existence of sock waves in certain situations. The appearance of instability through the linear subcritical region as well as irregular influences with respect to surface tension and couple-stress property was revealed. The nonlinear approach was more accurate in describing the stability issue than the linear one. Such results could be employed to attain the optimum statuses with regard to the film stability, and control the shock waves. They would not only enable accurate practical implementation in the design of inertial confinement fusion capsules and supernova explosions and implosions modelling, but also would allow for precise numerical simulation.

Bamboo as a natural optimized fiber reinforced composite: interfacial mechanical properties and failure mechanisms

Bamboo is a typical natural fiber-reinforced composite with an optimized distribution of vascular bundles as reinforcement and parenchyma tissues as bio-matrix. The interfacial bonding performance between vascular bundles and parenchyma tissue is critical for the mechanical properties and failure mechanisms of bamboo. This study employed pull-out tests to determine the interfacial shear strength (IFSS) between bamboo vascular bundles and parenchyma tissue and evaluate the critical embedded lengths () of vascular bundles. The effects of embedded vascular bundle lengths on interfacial strength and failure behaviors were also investigated. The results revealed a value of 2.51 mm, lower than the majority of plant fiber-reinforced composite materials, with an IFSS of around 20 MPa, surpassing most artificial bamboo fiber composites. The pull-out process of the vascular bundles involved elasticity, debonding, and sliding friction stage, where debonding energy absorption (DEA) outweighed frictional energy absorption (FEA) and increasing with embedded length. The primary failure features include interfacial debonding, parenchyma tissue ripping, delamination of fiber thin layers, and fiber breakage. Moreover, the parenchyma cells between the two fiber sheaths and at the top of the bamboo block readily detached. The interfacial failure mechanisms of bamboo included debonding, reinforcement, and matrix failure, with the proportions varying as the embedded length increased. Quantitative analysis of the interfaces structure and mechanical properties between vascular bundles and parenchyma tissues could provide a reference for the biomimicry of bamboo structures and the manufacturing of natural fiber-reinforced composite materials.

Synthesis, Characterization, and Optimization of Novel Furan-ring Fused Chalcones via Radical Cyclization of α,β-Unsaturated Ketones and Cyclic Ketone

Abstract: Novel Furan-ring Fused Chalcones (FFC) were synthesized using a radical cyclization reaction of α,β-unsaturated ketones with cyclic ketone as the model reaction to attain this goal. In this study, traditional and microwave-assisted methods for the efficient and cost-effective synthesis of furan-ring fused chalcones in mild reaction conditions are compared and optimized. The goal is to develop a reliable and adaptable synthetic technique that may be used to produce these useful chalcone derivatives quickly and effectively. The optimal experimental conditions for these reactions were carefully determined using two independent methodologies: conventional (Method A) and microwave (Method B). The results indicated that the proposed method B could be used effectively in the future to synthesize novel furans with short reaction times and acceptable yields (87-94 %), and products were purified by column chromatography and preparative thin layer chromatography (PTLC). All new compounds were characterized by 1H-NMR, 13C-NMR, LC-MS, and elemental analyses.

New U-Pb zircon tuff ages and revised stratigraphic correlations in the Superior craton during the Great Oxidation Episode

Major environmental changes during the Great Oxidation Episode are recorded in 2.5–2.0 Ga sedimentary successions across the world. In North America, the Huronian Supergroup is the most complete succession, preserving three glacial intervals with possible equivalents in the Lake Superior region. The third and youngest glacial unit (Gowganda Formation, Cobalt Group) of the Huronian Supergroup has been correlated with glacial deposits of the Chocolay Group in the Lake Superior region. Here we present the results of in situ SHRIMP U-Pb geochronology of zircon in thin tuff layers from the basal Wewe Slate, Chocolay Group, from drill-core in the Marquette Range area, upper Michigan. Zircon U-Pb data from two intervals ∼16 m apart yielded weighted mean 207Pb/206Pb ages of 2174 ± 9 Ma and 2172 ± 6 Ma, which define the depositional ages of the Wewe Slate and the conformably underlying Kona Dolomite. In the Huronian Supergroup, SHRIMP U-Pb dating of zircon in a tuff bed from the Gordon Lake Formation, Cobalt Group, yielded a weighted mean 207Pb/206Pb age of 2318 ± 8 Ma, interpreted to be the age of deposition. Re-examination of previously published U-Pb zircon data from the Gordon Lake Formation (Rasmussen et al., 2013) yields a slightly older weighted mean 207Pb/206Pb age of 2310 ± 5 Ma. Our results show that the Wewe Slate, and probably the Kona Dolomite, are ∼150 million years younger than the ∼2.32 Ga Gordon Lake Formation, with which they were previously correlated. Our results suggest that the glacial deposits in the Lake Superior region represent a fourth Paleoproterozoic glaciation in North America, whose age range corresponds to that of the fourth and final early Paleoproterozoic glaciation in southern Africa. We propose that the Chocolay Group was deposited after the Huronian Supergroup and is broadly coeval with the rift-passive margin succession (Cycle 1 of the Kaniapiskau Supergroup) in the New Québec Orogen, Canada, whose deposition has been linked to rifting and breakup along the eastern margin of the Superior craton at ∼2.22 Ga.

Real-time and highly responsive hydrogen mapping in pure Fe using TiO2 thin films

A hydrogen visualization method with high responsivity and chemical stability under atmospheric corrosion is necessary to inhibit hydrogen embrittlement, which can occur with hydrogen uptake of structural materials. In this study, a highly responsive hydrogen mapping technique for steels was successfully established using a TiO2 thin film and Pd intermediate layer. The color of the TiO2 film on the hydrogen-detection side changes during hydrogen charging on the hydrogen-entry side of the Fe specimen, indicating that the color changes were attributed to the hydrogen uptake of the Fe surface and subsequent introduction of hydrogen atoms to the TiO2 film. Considering the responsivity and visibility, the optimal thickness of the TiO2 film was determined to be 20 nm. As TiO2 is a chemically stable material, the proposed mapping technique can be used to monitor the hydrogen absorbed into metallic materials under outdoor conditions.

Improving the Transparency of a MgAl2O4 Spinel Damaged by Sandblasting through a SiO2-ZrO2 Coating

Transparent materials in contact with harmful environments such as sandstorms are exposed to surface damage. Transparent MgAl2O4 spinel used as protective window, lens or laser exit port, among others, is one of the materials affected by natural aggressions. The impact of sand particles can cause significant defects on the exposed surface, thus affecting its optical and mechanical behavior. The aim of this work is to improve the surface state of a spinel damaged surface by the deposition of a thin layer of SiO2-ZrO2. For this purpose, spinel samples obtained from different commercial powders sintered by Spark Plasma Sintering were sandblasted and further coated with a SiO2-ZrO2 thin layer. The coating was successfully synthesized by the sol/gel method, deposited on the sandblasted samples and then treated at 900 °C, reaching a final thickness of 250 nm. The results indicated that sandblasting significantly affects the surface of the spinel samples as well as the optical transmission, confirmed by UV-visible spectroscopy and profilometry tests. However, the deposition of a SiO2-ZrO2 coating modifies the UV-visible response. Thus, the optical transmission of the S25CRX12 sample presents the best transmission values of 81%, followed by the S25CRX14 sample then the S30CR sample at 550 nm wavelength. An important difference was observed between sandblasted samples and coated samples at low and high wavelengths. At low wavelengths (around 200 nm), sandblasting tends to improve significantly the transmission of spinel samples, which exhibit a low transmission in the pristine state. This phenomenon can be attributed to the healing of small superficial defects responsible for the degradation of transmission such as pores or flaws. When the initial transmission at 200 nm is high, the sandblasting worsens the transmission. Sandblasting reduces slightly the transmission values for long wavelengths due to the formation of large superficial defects like chipping by creation and propagation of lateral cracks. The coating of the sandblasted samples exhibits some healing of defects induced by sandblasting. The deposition of the SiO2-ZrO2 layer induces a clear increase in the optical transmission values, sometimes exceeding the initial values of the transmission in the pristine state.

Probing the Thermal and Electrical Properties of Ultrawide Bandgap Nitrogen‐Polar AlGaN Heterostructures

AbstractUltra‐wide bandgap semiconductor AlGaN is a promising candidate for high‐power and high‐frequency electronics. AlGaN‐heterostructures with nitrogen (N)‐polarity can offer added benefits of low‐leakage and large drive current. However, electro‐thermal transport in such heterostructures remains unexplored, although they are essential for electronic device functionality. Here, the thermal and electrical properties of N‐polar AlxGa1‐xN‐channel heterostructures (Al percentage, x = 15–90%) are explored and compared with their GaN counterpart. The thermal measurements uncover that the effective thermal resistance of the thin channel and barrier layers are similar in magnitudes for N‐polar‐ AlGaN and GaN heterostructures, however, the total effective thermal conductivity in N‐polar AlGaN heterostructure is ≈4× smaller. This reduction originates from the larger thermal resistance of the thick Al0.15Ga0.85N buffer layer within the AlGaN stack. N‐polar AlxGa1‐xN stack displays a thermal conductivity almost independent of temperature, measured from room temperature up to 200 °C. Hall measurements of an N‐polar Al0.30Ga0.70N‐channel heterostructure further reveal that electrical properties such as resistivity, carrier density, and mobility remain nearly unchanged with temperature, indicating the dominance of alloy‐phonon scattering in such material systems. These results offer important insights into material‐device co‐design and reliability of N‐polar AlGaN heterostructures.

Comprehensive Design and Analysis of Thin Film Sb2S3/CIGS Tandem Solar Cell: TCAD Simulation Approach

Abstract This research presents a design and analysis of a tandem solar cell, combining thin film wide bandgap Sb2S3 (1.72 eV) and narrow bandgap CIGS (1.15 eV) for the top and bottom sub-cells, respectively. The integration of all thin film layers enhances flexibility, rendering the tandem solar cell suitable for applications such as wearable electronics. To optimize the power conversion efficiency (PCE) of the tandem solar device, advanced technology computer-aided design (TCAD) simulation tools are employed to estimate loss mechanisms and fine-tune parameters for each layer. An experimentally validated optoelectronic model is introduced, calibrated and validated against fabricated reference solar cells for the individual top and bottom cells. The calibrated model is then utilized to propose optimization routines for the Sb2S3/CIGS tandem solar cell. The initial tandem cell exhibits a JSC of 15.72 mA/cm2 and a PCE of 15.36%. The efficiency drop in the tandem configuration is identified primarily in the top cell. A systematic optimization process for the top cell is initiated, exploring various configurations, including HTL-free and ETL-free setups. Moreover, an np homojunction structure for the top cell is proposed. Optimization routines are applied that involve determining optimal thickness and doping concentration of the n-layer, investigating the effect of p-layer doping concentration, and exploring the influence of the work function of the front contact. As a result, the tandem cell efficiency is significantly improved to 23.33% at the current matching point (CMP), with a JSC of 17.15 mA/cm2. The findings contribute to the advancement of thin-film tandem solar cell technology, showcasing its potential for efficient and flexible photovoltaic applications.

Microwave-transparent metallic metamaterials for autonomous driving safety.

Maintaining the surface transparency of protective covers using transparent heaters in extreme weather is imperative for enhancing safety in autonomous driving. However, achieving both high transmittance and low sheet resistance, two key performance indicators for transparent heaters, is inherently challenging. Here, inspired by metamaterial design, we report microwave-transparent, low-sheet-resistance heaters for automotive radars. Ultrathin (approximately one ten-thousandth of the wavelength), electrically connected metamaterials on a millimetre-thick dielectric cover provide near-unity transmission at specific frequencies within the W band (75-110 GHz), despite their metal filling ratio exceeding 70 %. These metamaterials yield the desired phase delay to adjust Fabry-Perot resonance at each target frequency. Fabricated microwave-transparent heaters exhibit exceptionally low sheet resistance (0.41 ohm/sq), thereby heating the dielectric cover above 180 °C at a nominal bias of 3 V. Defrosting tests demonstrate their thermal capability to swiftly remove thin ice layers in sub-zero temperatures.

Examination of Operational Methods for a Low-Temperature Aquifer Thermal Storage Air Conditioning System Based on Operational Performance and Considerations of Thermal Storage and Pumping Volume Balance

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Detailed actual performance data measured over four years are presented, and performance analysis results show that a COP of 5 was achieved for the overall building cooling and heating system. In addition, the study provides a detailed analysis of the imbalance in heat quantity, remaining heat storage, and other factors based on actual data, identifying operational issues and summarizing specific improvement measures. Finally, as a proposal for a sustainable operational method to balance the cumulative heat storage and pumping volume of cold and hot water, specific operational procedures are summarized, including setting the return water temperature for the next season based on the dimensionless average pumping temperature of the previous season, and a flowchart is presented. There is no prior research that shows such specific operational procedures, and this can be considered an important achievement of this study.

Imaging ultra-weak UV light below 100 pW cm-2 using a 4H-SiC photodetector with an Al2O3 interfacial layer.

Weak light detection is crucial in various practical applications such as night vision systems, flame monitoring, and underwater operations. Decreasing the dark current of a photodetector can effectively mitigate noises, consequently enhancing the signal-to-noise ratio and overall weak light detection performance. Herein, we demonstrate a 4H-SiC UV photodetector capable of detecting extremely weak UV light. This device comprises a photosensitive layer of 4H-SiC, two TiN electrodes and an atomically thin Al2O3 interfacial layer between TiN and the C surface of 4H-SiC. Under 360 nm UV light illumination, the proposed Al2O3 device demonstrates an ultra-low dark current of 18 fA, possibly benefiting from the effective passivation of interfacial carriers, and a boosted photo-to-dark current ratio of 6.7 × 107. Consequently, it achieves a weak-light detection limit as low as 31.8 pW cm-2, significantly outperforming the control device lacking Al2O3. When compared to previously reported SiC photodetectors, our Al2O3 device boasts an exceptional large linear dynamic range of 172 dB. Leveraging this, we construct a photodetector array capable of clearly imaging an object under ultra-weak light illumination below the 100 pW cm-2 level. The proposed photodetector represents a significant advancement in the development of highly sensitive image sensors for weak light detection.

Thin-film flow between a rotating sphere and a nearly vertical moving plate

When a sphere rotates near a rigid boundary coated with a thin layer of viscous liquid, ‘tracks’ are generated both behind and over the sphere. This paper describes a theory for the simplest one-track configuration which can occur under particular experimental conditions. The theoretical predictions are in good agreement with experimental observations.

Atmospheric plasma treatment effect on shear strength of GFRP-Aluminum adhesively bonded lap joints

The objective of this study is to investigate the effect of air (dielectric barrier discharge) DBD plasma treatment on the bonding strength of adhesively bonded glass fiber-reinforced epoxy composite-aluminum lap joints. The bonding performance of lap joints produced by the plasma treatment was compared with that of untreated and peel-ply surface treatments. Water contact angles of the substrates were measured for untreated, peel-ply, and plasma surface-treated substrates. Experimental results showed that plasma-treated aluminum and GFRP substrates increased the wettability properties and thus shear strength of adhesively bonded GFRP-Al joints increased. After the shear tests, the fracture surfaces of the substrates were visually examined and three different damage modes were observed, including light fiber tear failure, adhesive failure, and thin layer cohesive failure modes.

Microporous Electrode Binders for Anion Exchange Membrane Water Electrolyzers.

In anion exchange membrane (AEM) water electrolyzers, AEMs separate hydrogen and oxygen, but should efficiently transport hydroxide ions. In the electrodes, catalyst nanoparticles are mechanically bonded to the porous transport layer or membrane by a polymeric binder. Since these binders form a thin layer on the catalyst particles, they should not only transport hydroxide ions and water to the catalyst particles, but should also transport the nascating gases away. In the worst case, if formation of gases is >> than gas transport, a gas pocket between catalyst surface and the binder may form and hinder access to reactants (hydroxide ions, water). In this work, the ion conductive binder SEBS-DABCO is blended with PIM-1, a highly permeable polymer of intrinsic microporosity. With increasing amount of PIM-1 in the blends, the permeability for water (selected to represent small molecules) increases. Simultaneously, swelling and conductivity decrease, due to the increased hydrophobicity. Ex situ data and electrochemical data indicate that blends with 50% PIM-1 have better properties than blends with 25% or 75% PIM-1, and tests in the electrolyzer confirm an improved performance when the SEBS-DABCO binder contains 50% PIM-1.

Effective use of adaptive slicing in binder jetting using Taguchi method and surface roughness measurement with image processing

Purpose The use of additive manufacturing in many branches of industry is increasing significantly because of its many advantages, such as being able to produce complex parts that cannot be produced by classical methods, using fewer materials, easing the supply chain with on-site production, being able to produce with all kinds of materials and producing lighter parts. The binder jetting technique, one of the additive manufacturing methods researched within the scope of this work, is predicted to be the additive manufacturing method that will grow the most in the next decade, according to many economic reports. Although additive manufacturing methods have many advantages, they can be slower than classical manufacturing methods regarding production speed. For this reason, this study aims to increase the manufacturing speed in the binder jetting method. Design/methodology/approach Adaptive slicing and variable binder amount algorithm (VBAA) were used to increase manufacturing speed in binder jetting. Taguchi method was used to optimize the layer thickness and saturation ratio in VBAA. According to the Taguchi experimental design, 27 samples were produced in nine different conditions, three replicates each. The width of the samples in their raw form was measured. Afterward, the samples were sintered at 1,500 °C for 2 h. After sintering, surface roughness and density tests were performed. Therefore, the methods used have been proven to be successful. In addition, measurement possibilities with image processing were investigated to make surface roughness measurements more accessible and more economical. Findings As a result of the tests, the optimum printing condition was decided to be 180–250 µm for layer thickness and 50% for saturation. A separate test sample was then designed to implement adaptive slicing. This test sample was produced in three pieces: adaptive (180–250 µm), thin layer (180 µm) and thick layer (250 µm) with the determined parameters. The roughness values of the adaptive sliced sample and the thin layer sample were similar and better than the thick layer sample. A similar result was obtained using 12.31% fewer layers in the adaptive sample than in the thin layer sample. Originality/value The use of adaptive slicing in binder jetting has become more efficient. In this way, it will increase the use of adaptive slicing in binder jetting. In addition, a cheap and straightforward image processing method has been developed to calculate the surface roughness of the parts.

Reconfigurable image processing metasurfaces with phase-change materials.

Optical metasurfaces have enabled analog computing and image processing within sub-wavelength footprints, and with reduced power consumption and faster speeds. While various image processing metasurfaces have been demonstrated, most of the considered devices are static and lack reconfigurability. Yet, the ability to dynamically reconfigure processing operations is key for metasurfaces to be used within practical computing systems. Here, we demonstrate a passive edge-detection metasurface operating in the near-infrared regime whose response can be drastically modified by temperature variations smaller than 10 °C around a CMOS-compatible temperature of 65 °C. Such reconfigurability is achieved by leveraging the insulator-to-metal phase transition of a thin layer of vanadium dioxide, which strongly alters the metasurface nonlocal response. Importantly, this reconfigurability is accompanied by performance metrics-such as numerical aperture, efficiency, isotropy, and polarization-independence - close to optimal, and it is combined with a simple geometry compatible with large-scale manufacturing. Our work paves the way to a new generation of ultra-compact, tunableand passive devices for all-optical computation, with potential applications in augmented reality, remote sensing and bio-medical imaging.

The role of sulfate in the hydrothermal replacement of aragonite single crystals by calcite

Aragonite (CaCO3) is a stable calcium carbonate phase under high pressure conditions. However, its formation in (sub)surface environments, where calcite is the stable polymorph, is widespread. Regardless of its origin, aragonite is expected to undergo transformation into calcite under moderate pressures and temperatures. However, this transformation does not always take place, which results in the presence of abundant aragonitic relics in the geological record. Traditionally, this preservation has been explained by the presence of chemical inhibitors that prevent the conversion of aragonite to calcite. While it is widely accepted that magnesium (Mg) plays a key role in the polymorphic selection of CaCO3, the influence of other ions has also been suggested. This work evaluates the effect that different concentrations of sulfate (SO42−) in the fluid has on the progress of the aragonite-to-calcite transformation at 220 °C. Our results show that, upon reaction with deionized water or sulfate-poor solutions ([SO42−]aq < 0.1 mM), aragonite single crystals are extensively replaced by calcite aggregates (crystal size > 15 µm) through an interface coupled dissolution-precipitation reaction. The replacement starts at the aragonite crystal surfaces and advances inwards thanks to the development of an extensive network of fractures. Contrarily, when the solution bears higher concentrations of sulfate ([SO42−]aq > 0.1 mM), only a thin layer of smaller crystals of calcite (< 10 µm) form on the aragonite substrates, without any further transformation taking place. We interpret that these smaller crystals exert too little crystallization pressure and fail to promote the development of a network of fractures. In the absence of this network, the aragonite-calcite transformation cannot take place. The transformation does not occur neither when the experiments are conducted with deionized water and fragments of gypsum or anhydrite together with the aragonite grains. The results of this study shed light on the influence of dissolved sulfate in the kinetics of the fluid-driven transformation of aragonite into calcite. These results are useful to understand the preservation of aragonite in a variety of current geological settings and provide valuable insights for better understanding the diagenesis of sedimentary carbonates.

Catalytic strategies for uniform monolayer MoSe2 growth in CVD processes

To facilitate the widespread utilization of devices based on two-dimensional transition metal dichalcogenide (TMDC) materials, addressing the challenge of producing large-area and uniform monolayers is crucial. In this study, we investigated the efficacy of various catalysts in promoting the growth of monolayer MoSe2 through chemical vapor deposition (CVD) as a potential solution to improve surface coverage and uniformity while maintaining the monolayer structure. Five distinct water-soluble catalysts (sodium chloride (NaCl), zinc chloride (ZnCl2), potassium hydroxide (KOH), potassium chloride (KCl), potassium oxalate (K2C2O4)) were employed in conjunction with a glass substrate for the CVD-based growth of monolayer MoSe2. We applied these catalyst solutions as thin layers onto SiO2/Si substrates to observe their specific catalytic effects on monolayer MoSe2 formation. MoSe2 was selected as the target material due to its promising characteristics within the TMDC family, particularly its high mobility. Our findings revealed that NaCl, ZnCl2, KCl, and K2C2O4 catalysts enhanced monolayer growth in the 2H phase on SiO2/Si substrates, while the glass substrate resulted in a hybrid 1T/2H MoSe2 structure, albeit with the highest surface coverage. Furthermore, the use of a catalyst allowed us to bypass the laborious transfer step by enabling direct growth of the MoSe2 flakes on the Si/SiO2 substrate, eliminating the risk of flake damage arising from the transfer process. Among the catalyst solutions, NaCl yielded the most homogeneous MoSe2 monolayer growth with relatively high coverage.

Review on Environmentally Assisted Static and Fatigue Cracking of Al-Mg-Si-(Cu) Alloys

This paper reviews the relevant literature and covers the main aspects of the environmentally assisted cracking of Al-Mg-Si-(Cu) alloys. Apart from a brief overview of the major microstructural and mechanical properties, it presents research results on the corrosion sensitivity and stress corrosion susceptibility of Al-Mg-Si alloys. Possible mechanisms of stress corrosion cracking and corrosion fatigue in aluminum alloys, such as anodic dissolution and/or interaction with hydrogen, are considered. A number of factors, including atmospheric or solution conditions, applied stress, and material properties, can affect these mechanisms, leading to environmentally assisted cracking. Specific attention is given to Al-Mg-Si alloys with copper, which may increase the sensitivity to intergranular corrosion. The susceptibility to both intergranular corrosion and stress corrosion cracking of Cu-containing Al-Mg-Si alloys is mostly associated with a very thin layer (segregation) of Cu on the grain boundaries. However, the effect of Cu on the corrosion fatigue and fatigue crack growth rate of Al-Mg-Si alloys has received limited attention in the literature. At the current state of the research, it has not yet been holistically assessed, although a few studies have shown that a certain content of copper can improve the resistance of aluminum alloys to the environment with regard to corrosion fatigue. Furthermore, considerations of the synergistic actions of various factors remain essential for further studying environmentally assisted cracking phenomena in aluminum alloys.