Thickness Shear Vibration Mode Research Articles

Near Stochiometric LiNbO3 Crystal: the Piezoelectric Features and the Shear Horizontal Guided Wave Transducer for Structural Health Monitoring up to 650 °C.

The application of shear horizontal (SH) guided wave transducers in high-temperature structural health monitoring (SHM) is a topic of significant interest across various industrial engineering sectors. In this study, we utilized the novelty piezoelectric crystal of near stoichiometric lithium niobate (NSLN), which exhibited a robust piezoelectric response (d15 = 77.6 pC/N@room temperature). Next, the pure thickness shear vibration mode d15' through size optimization was designed. It was demonstrated that the NSLN-based ultrasonic guided wave transducers utilizing the optimum d15' mode were proficient in transmitting and receiving pure fundamental SH wave (SH0 wave) along two orthogonal main directions (0° and 90°) over a wide frequency range (100-350 kHz), exhibiting strong response to the SH0 wave. Under the driving voltage of 100 V, the signal voltages of the NSLN-based transducer were found to be on the order of 200.3 and 11.8 mV at room temperature and high temperature of 650 °C, respectively. Moreover, the NSLN-based SH0 transducer showcased its better defect localization ability, and the signal-to-noise ratio (SNR) sensitivity of NSLN-based transducer was evaluated to be 16.1 dB at high temperature of 650 °C. To sum up, the ultrasonic wave transducer based on NSLN crystal demonstrated higher potential applications for in situ SHM under elevated temperatures.

Ultrahigh‐Temperature Piezoelectric Crystal YbBa3(PO4)3 for Vibration Sensing Application

AbstractHigh‐temperature vibration sensors are of great importance for accurate monitoring of dynamic mechanical conditions in automotive, aerospace and energy‐generation‐related systems. Currently, piezoelectric crystals with ultrahigh operational temperature and good piezoelectric performance for high‐temperature sensing applications are attracting considerable attention. Herein, a novel piezoelectric crystal YbBa3(PO4)3 with cubic symmetry and a high melting point of ≈1850 °C is explored, and grown by using the Czochralski method. The temperature‐dependent behaviors of electro‐elastic constants and electrical resistivity are investigated ranging from 25 to 800 °C, where the dielectric loss of the YbBa3(PO4)3 crystal is found to be ≈15% at 800 °C. In addition, an optimal crystal cut with a pure thickness shear vibration mode is designed. The optimal crystal cut presents a good piezoelectric activity ( = 12.6 pC N−1) as well as good temperature stability. Furthermore, a high‐temperature accelerometer with shear piezoelectric mode is designed and fabricated using the YbBa3(PO4)3 crystal, and the sensing performance at elevated temperature are evaluated. The average sensitivity is found to be 1.16 pC g−1, with a small temperature deviation (≈7.7%), exhibiting a good temperature stability. All these results indicate that YbBa3(PO4)3 piezoelectric crystal is a promising candidate for high‐temperature piezoelectric sensing applications.

Investigation of Electro-Elastic Properties for LN Single Crystals at Low Temperature

Lithium niobate crystals (LiNbO3, LN) are multifunctional crystal materials with many outstanding properties. In this work, the electro-elastic properties of LN single crystals were explored at temperatures from −150 °C to 150 °C. The temperature dependences of dielectric permittivities, elastic compliances, electromechanical coupling factors and piezoelectric coefficients were determined using the impedance method. The LN crystals possessed large dielectric permittivities, the ε11T/ε0 and ε33T/ε0 were 83.2 and 29.4 at room temperature, respectively. The elastic compliances s11, s13, s33 and s44 presented a positive increase as the temperature increased, and the variations were 5.0%, 8.2%, 4.6% and 5.4%, respectively, showing a good temperature stability. Moreover, the temperature dependence of the electromechanical coupling factors and piezoelectric coefficients for different vibration modes were studied with a temperature range from −150 °C to 150 °C, where the thickness shear vibration mode d15 presented a large piezoelectric response and minimal temperature variation.

Real-time multianalyte biosensors based on interference-free multichannel monolithic quartz crystal microbalance.

In this work, we design, fabricate and characterize a new interference-free multichannel monolithic quartz crystal microbalance (MQCM) platform for bio-sensing applications. Firstly, interference due to thickness-shear vibration mode coupling between channels in MQCM array is effectively suppressed by interposing a polydimethylsiloxane wall between adjacent QCM electrodes on a quartz substrate to form inverted-mesa-like structure. In addition, the electrical coupling due to the electrical impedance of solution is diminished by extending the flow path between them with an extended-design flow channel. The electrical testing results show that individual QCM signal is unaffected by those of adjacent channels under liquid loading, signifying the achievement of interference-free MQCM. The MQCM is applied for multi-analyte biosensing of IgG and HSA. The anti-IgG and anti-HSA are separately immobilized on two adjacent QCM electrodes, which are subsequently blocked with BSA to avoid unspecific binding. The MQCM biosensors are tested with single- and double-analyte solutions under continuous flow of buffer. The IgG and HSA QCM sensors only show frequency shift responses to their corresponding analytes and there are very small cross frequency shifts due to remnant unspecific binding. Moreover, MQCM sensors show approximately linear frequency shift response with analyte concentration. Therefore, the developed MQCM platform is promising for real-time interference-free label-free detection and quantification of multiple bio-analytes.

Critical Property in Relaxor-PbTiO(3) Single Crystals --- Shear Piezoelectric Response.

The shear piezoelectric behavior in relaxor-PbTiO(3) (PT) single crystals is investigated in regard to crystal phase. High levels of shear piezoelectric activity, d(15) or d(24) >2000 pC N(-1), has been observed for single domain rhombohedral (R), orthorhombic (O) and tetragonal (T) relaxor-PT crystals. The high piezoelectric response is attributed to a flattening of the Gibbs free energy at compositions proximate to the morphotropic phase boundaries, where the polarization rotation is easy with applying perpendicular electric field. The shear piezoelectric behavior of pervoskite ferroelectric crystals was discussed with respect to ferroelectric-ferroelectric phase transitions and dc bias field using phenomenological approach. The relationship between single domain shear piezoelectric response and piezoelectric activities in domain engineered configurations were given in this paper. From an application viewpoint, the temperature and ac field drive stability for shear piezoelectric responses are investigated. A temperature independent shear piezoelectric response (d(24), in the range of -50°C to O-T phase transition temperature) is thermodynamically expected and experimentally confirmed in orthorhombic relaxor-PT crystals; relatively high ac field drive stability (5 kV cm(-1)) is obtained in manganese modified relaxor-PT crystals. For all thickness shear vibration modes, the mechanical quality factor Qs are less than 50, corresponding to the facilitated polarization rotation.

Thickness-shear vibration of rotated Y -cut quartz plates with unattached electrodes and asymmetric air gaps

Thickness-shear vibration modes of rotated Y-cut quartz plates with unattached electrodes and asymmetric air gaps are analyzed. An exact solution is obtained from the equations of piezoelectricity. Numerical results calculated from the solution show that the resonant frequencies are sensitive to the dimensions of the air gaps. This offers new design parameters for better resonator performance.

Radial vibration mode of 0.71Pb(Mg1∕3Nb2∕3)O3–0.29PbTiO3 single crystal and its applications

Ferroelectric single crystal (1−x)Pb(Mg1∕3Nb2∕3)O3–xPbTiO3 (PMNT) has attracted considerable attention for its outstanding piezoelectric properties after poled along the ⟨001⟩ or ⟨101⟩ directions and it is being actively applied to various ultrasonic devices. However, almost all previous applications focus on the longitudinal extension, transverse extension, thickness extension and thickness shear vibration mode. Here, we investigated the radial vibration mode of the ⟨001⟩ poled 0.71Pb(Mg1∕3Nb2∕3)O3–0.29PbTiO3 single crystal. Both the finite element simulation and experimental results have shown that the performance of radial vibration mode is excellent. The coupling coefficient of radial vibration mode can reach 0.84 and the anisotropy of the circular plate is very weak after it was poled along the ⟨001⟩ direction. Based on this mode, we further designed and fabricated a disk-type piezoelectric transformer and the open circuit voltage step-up ratio reached about 50 with no spurious vibration mode around the resonance frequency. All these have shown that the radial vibration mode of PMNT single crystal is also promising and useful for other piezoelectric device applications.

Vibration distribution in output sections of a piezoelectric transformer operating at thickness shear mode

In this study, the vibration distribution along the width direction in the output section of a piezoelectric transformer operating at the thickness shear vibration mode is investigated experimentally and theoretically. It is experimentally found that the vibration of output section has a spatial gradient and attenuates as the distance from the input section increases. A theoretical model is developed to estimate the vibration attenuation in the output section, which provides the guidelines of optimizing the transformer and explains some important phenomena such as the nonuniform temperature distribution in piezoelectric transformers. The larger the load resistance, the larger the vibration gradient is. At the resonant frequency, the vibration gradient decreases with increasing the width of the input or output section, and it changes little with the length and thickness of the transformer when the load resistance matches with the piezoelectric transformer. The vibration gradient increases with increasing the length or decreasing the thickness when the load resistance is constant, in which the load does not match with the transformer.

Energy trapping of thickness-shear vibration modes of elastic plates with functionally graded materials

Energy trapping has important applications in the design of thickness-shear resonators. Considerable efforts have been made for the effective utilization and improvement of energy trapping with variations of plate configurations, such as adding electrodes and contouring. As a new approach in seeking improved energy trapping feature, we analyze thickness-shear vibrations in an elastic plate with functionally graded material (FGM) of in-plane variation of mechanical properties, such as elastic constants and density. A simple and general equation governing the thickness-shear modes is derived from a variational analysis. A plate with piecewise constant material properties is analyzed as an example. It is shown that such a plate can support thickness-shear vibration modes with obvious energy trapping. Bechmann's number for the existence of only one trapped mode also can be determined accordingly.

High- κ dielectrically transduced MEMS thickness shear mode resonators and tunable channel-select RF filters

Electrically coupled, high quality factor ( Q), tunable channel-select ladder filters comprised of dielectrically transduced thickness shear mode resonators are presented using integrated circuit compatible bulk micromachining technology. The filters are fabricated on the 3.2 μm thick device layer of heavily doped SOI wafers with a 20 nm thick hafnium dioxide film sandwiched between the polysilicon electrodes and the silicon device layer. The ladder filter consists of shunt and series resonators operating in the half-wave thickness shear vibration mode. Dielectric transduction provides a k 2 reduction in motional impedance relative to air-gap electrostatic transduction. Each constituent resonator of the filter can be excited at above 810 MHz resonant frequency with Q of 7800 in air and a motional impedance ( R X ) of 59 Ω. The ladder filter demonstrates a center frequency tuning range 8–817 MHz and an adjustable bandwidth from 600 kHz to 2.8 MHz, while maintaining an insertion loss <4 dB, stop-band rejection >30 dB and pass-band ripple <2 dB. By having a tunability feature, RF MEMS filters can accommodate various signal waveforms with bandwidth range 0.1–5 MHz. In addition, errors due to fabrication can be compensated and capacitive loading in receiver architecture can be minimized.

Modeling and analysis of dual-output piezoelectric transformer operating at thickness-shear vibration mode

In our previous study, the multioutput piezoelectric transformer operating at the thickness-shear vibration mode was proposed and experimentally investigated. By designing a new construction of support and lead wire connection, a power density of 52.7 W/cm3 and a total output power of 169.8 W were achieved at a temperature rise less than 20 degrees C. In this work, a theoretical model was developed for the dual-output piezoelectric transformer operating at the thickness-shear vibration mode. The equivalent circuit parameters of the piezoelectric transformer were derived. Based on this, the impedance characteristics, equivalent inductance, capacitance ratio, voltage gain, and efficiency of the piezoelectric transformer were calculated. The theoretical results were verified by experimental data. Furthermore, the effect of the transformer size on the voltage gain, efficiency, output power and power density, and the effect of the load of one output on the voltage gain of another output were analyzed. Some useful guidelines were achieved by these analyses.

A tunable low-frequency piezoelectric phase shifter

This paper presents a new technique of shifting the phase of a low-frequency AC voltage. The technique is derived from the multioutput piezoelectric transformer. The piezoelectric phase shifter is made of a piezoelectric ceramic plate operating at the thickness shear vibration mode. The ceramic plate consists of input, output and control parts. The control part is connected to a tunable inductor or capacitor, which can tune the phase shift between the output and input voltages smoothly. The phase shift can be increased by decreasing the inductance or capacitance at the control part. Tuning a DC bias voltage applied to the input part may also change the phase shift. A maximum phase shift of 128° and minimum phase shift of −10° are achieved by the prototype of the phase shifter. The phase shifter has a wide phase shift range, good ability to manage high power and relatively high energy transmission efficiency.

Detection of longitudinal defect in pipes using torsional modes

The multi-modes and disperse characteristics of torsional modes in pipes are investigated theoretically and experimentally. At all frequencies, both phase velocity and group velocity of the lowest torsional mode T(0,1) are constant and equal to shear wave velocity. T(0.1) mode at all frequencies is the fastest torsional mode. In the experiments, T(0,1) mode is excited and received in pipes using 9 thickness shear vibration mode piezoelectric ceramic elements. Furthermore, an artificial longitudinal defect of a 4 m long pipe is detected using T(0,1) mode at 50 kHz. Experimental results show that it is feasible for longitudinal defect detection in pipes using T(0,1) mode of ultrasonic guided waves.

Piezoelectric Properties of SrBi2Nb2O9 Textured Ceramics

The textured ceramics of the bismuth layer structured ferroelectrics SrBi2Nb2O9 (SBN)-type compound were fabricated by the templated grain growth (TGG) method, and their characteristics and piezoelectric properties were studied. Platelike particles with a large shape anisotropy, which were needed as template particles in the TGG process, were obtained for the composition with 10% Nd substitution on the Sr site of SBN. Highly (00ℓ) textured Sr0.9Nd0.1Bi2Nb2O9 (SNBN) ceramics were successfully obtained using the TGG process with platelike particles, and the orientation degree of the textured ceramics was 96%. The electromechanical coupling factor of the 96% orientation degree textured ceramics in the thickness shear vibration mode was three times as large as that for the randomly oriented ceramics. The temperature coefficient of the resonant frequency (TCF) of the textured ceramics was +20.9 ppm/°C, whose absolute value was two-thirds of that of the randomly oriented ceramics. The resonant frequency of the textured ceramics increased with temperature, while the resonant frequency of the randomly oriented ceramics decreased with increasing temperature. This result indicated the possibility of obtaining an excellent TCF by the optimization of grain orientation. Therefore, textured ceramics with orientation degrees from 54% to 96% were prepared using template particles of different average diameters, and an excellent TCF of -0.4 ppm/°C was obtained for the specimen with an orientation degree of 76%.

Piezoelectric transformer with high power density and multiple outputs

A new type of piezoelectric transformer which is capable of higher power density than currently known conventional types is presented. It is also capable of multiple voltage outputs. The transformer is made from lead zirconate titanate and is based on the k15 thickness shear vibration mode. This is the first reported case of such vibration mode being used to achieve high-power low-voltage piezoelectric transformers. Experimental characteristics of the prototype are reported. Such transformers are expected to find applications in automotive electronics and telecommunication power supplies.

High-Power, Multioutput Piezoelectric Transformers Operating at the Thickness-Shear Vibration Mode

In this study, a piezoelectric transformer operating at the thickness shear vibration mode and with dual or triple outputs is proposed. It consists of a lead zirconate titanate (PZT) ceramic plate with a high mechanical quality factor Q/sub m/ and a size of 120 /spl times/ 20 /spl times/ 4 mm/sup 3/. The PZT ceramic plate is poled along the width direction. The electrodes of input and output parts are on the top and bottom surfaces of the ceramic plate and separated by narrow gaps. A new construction of support and lead wire connection is used for the transformer. At a temperature rise less than 20/spl deg/C and efficiency of 90%, the piezoelectric transformer with dual outputs has a maximum total output power of 169.8 W, with a power of 129.5 W in one output and 40.3 W in another. The one with triple outputs has a maximum total output power of 163.1 W, with a power of 36.9 W in the first output, 13.0 W in the second output and 113.2 W in the third output. The maximum efficiency of the piezo-electric transformer with dual outputs and triple outputs is 98% and 95.7%, respectively. The voltage gains of the transformers are less than one, and different outputs have different gains. Also, there is a driving frequency range in which the load resistance of one output has little effect on the voltage gain of another output.

High-power, multioutput piezoelectric transformers operating at the thickness-shear vibration mode

In this study, a piezoelectric transformer operating at the thickness shear vibration mode and with dual or triple outputs is proposed. It consists of a lead zirconate titanate (PZT) ceramic plate with a high mechanical quality factor Q/sub m/ and a size of 120 /spl times/ 20 /spl times/ 4 mm/sup 3/. The PZT ceramic plate is poled along the width direction. The electrodes of input and output parts are on the top and bottom surfaces of the ceramic plate and separated by narrow gaps. A new construction of support and lead wire connection is used for the transformer. At a temperature rise less than 20/spl deg/C and efficiency of 90%, the piezoelectric transformer with dual outputs has a maximum total output power of 169.8 W, with a power of 129.5 W in one output and 40.3 W in another. The one with triple outputs has a maximum total output power of 163.1 W, with a power of 36.9 W in the first output, 13.0 W in the second output and 113.2 W in the third output. The maximum efficiency of the piezo-electric transformer with dual outputs and triple outputs is 98% and 95.7%, respectively. The voltage gains of the transformers are less than one, and different outputs have different gains. Also, there is a driving frequency range in which the load resistance of one output has little effect on the voltage gain of another output.

High-power, multioutput piezoelectric transformers operating at the thickness-shear vibration mode

In this study, a piezoelectric transformer operating at the thickness shear vibration mode and with dual or triple outputs is proposed. It consists of a lead zirconate titanate (PZT) ceramic plate with a high mechanical quality factor Qm and a size of 120 x 20 x 4 mm3. The PZT ceramic plate is poled along the width direction. The electrodes of input and output parts are on the top and bottom surfaces of the ceramic plate and separated by narrow gaps. A new construction of support and lead wire connection is used for the transformer. At a temperature rise less than 20 degrees C and efficiency of 90%, the piezoelectric transformer with dual outputs has a maximum total output power of 169.8 W, with a power of 129.5 W in one output and 40.3 W in another. The one with triple outputs has a maximum total output power of 163.1 W, with a power of 36.9 W in the first output, 13.0 W in the second output and 113.2 W in the third output. The maximum efficiency of the piezoelectric transformer with dual outputs and triple outputs is 98% and 95.7%, respectively. The voltage gains of the transformers are less than one, and different outputs have different gains. Also, there is a driving frequency range in which the load resistance of one output has little effect on the voltage gain of another output.

Thickness-Shear Vibration Mode Characteristics of SrBi4Ti4O15-Based Ceramics

Dielectric and piezoelectric properties have been investigated in bismuth layer-structure compounds SrBi4Ti4O15 (SBT) and BaBi4Ti4O15 (BBT)-based solid solutions. Lanthanum-substituted and manganese-added SBT and BBT form solid solutions for all levels of Ba substitution. The Curie temperature and coercive field strength decrease monotonously with the amount of Ba substitution. The mechanical quality factor, Qm, of the thickness-shear vibration mode also decreases. The value of elastic compliance increases with the amount of Ba substitution, but conversely its temperature dependency decreases.

Piezoelectric vibration component

First Page