Thermal Boundary Layer Thickness Research Articles

On the boundary-layer asymmetry in two-dimensional annular Rayleigh–Bénard convection subject to radial gravity

Radial unstable stratification is a potential source of turbulence in the cold regions of accretion disks. To investigate this thermal effect, here we focus on two-dimensional Rayleigh–Bénard convection in an annulus subject to radially dependent gravitational acceleration $g \propto 1/r$ . Next to the Rayleigh number $Ra$ and Prandtl number $Pr$ , the radius ratio $\eta$ , defined as the ratio of inner and outer cylinder radii, is a crucial parameter governing the flow dynamics. Using direct numerical simulations for $Pr=1$ and $Ra$ in the range from $10^7$ to $10^{10}$ , we explore how variations in $\eta$ influence the asymmetry in the flow field, particularly in the boundary layers. Our results show that in the studied parameter range, the flow is dominated by convective rolls and that the thermal boundary-layer (TBL) thickness ratio between the inner and outer boundaries varies as $\eta ^{1/2}$ . This scaling is attributed to the equality of velocity scales in the inner ( $u_i$ ) and outer ( $u_o$ ) regions. We further derive that the temperature drops in the inner and outer TBLs scale as $1/(1+\eta ^{1/2})$ and $\eta ^{1/2}/(1+\eta ^{1/2})$ , respectively. The scalings and the temperature drops are in perfect agreement with the numerical data.

Heat Transportation of 3D Chemically Reactive Flow of Jeffrey Nanofluid over a Porous Frame with Variable Thermal Conductivity

Nanofluids with variable thermal conductivity can potentially bring about a transformative impact in various industries. They offer adaptive and efficient heat transfer solutions that can adjust to changing conditions and specific requirements. The insertion of nanoparticles into the base fluid significantly changes its properties, affecting thermal conductivity and viscosity. The primary objective of this paper is to analyze the heat transfer rate and three-dimensional bio-convective flow of a non-Newtonian Jeffrey nanofluid across a porous surface with variable thermal conductivity. The investigation also considers the impacts of thermophoresis, Brownian motion, and the Lorentz force. The combine impact of thermal radiation and motile microbes also incorporated in the current study. To model these phenomena, we employ the boundary layer approximation to derive a system of partial differential equations (PDEs). These PDEs are subsequently simplified into more manageable ordinary differential equations (ODEs) using the similarity variables. The numerical analysis is performed via the finite difference approach, which consists of a three-stage Lobatto scheme using MATLAB package. Additionally, important engineering parameters under different constraints-like skin friction, Nusselt number, and Sherwood number—are given in a thorough manner using tabular and graphical representations. The results of this study demonstrate significant enhancements in various aspects, including thermophoresis, Brownian motion, and thermal boundary layer thickness are demonstrated through graphically and in the form of tables. As the thermal radiation parameter increases, the temperature profile rises accordingly. This enhancement in the temperature profile is directly attributable to the higher value of the radiation parameter, which results in a physical increase in temperature. These improvements are attributed to a reduction in viscous forces and an increase in the Brownian diffusion coefficient. This research advances the understanding of non-Newtonian thermally radiative flow with variable thermal conductivity, elucidating the complex behavior of such fluids and providing valuable insights for engineering applications.

Significance of spatial variability in heat generation on nonlinear mixed convective Jeffrey nanofluid flows nearby an impermeable plate

The dynamics of Jeffrey nanofluids over an elongated surface heated by convection are addressed adequately under the nonlinear Boussinesq’s sense. Novel attributes of exponential heat source and thermal radiation are included. Buongiorno’s revised nanoliquid model is implemented to study the uneven dispersion and thermophoresis of nanoparticles subjected to passive control of nanoparticles on the surface. Wall suction or injection effects are also considered. Mathematical modeling is developed and treated numerically using the similarity approach. The results are presented considering numerous values of the physical parameters. Stimulus variables that regulate the resulting dimensionless physical quantities are examined graphically. Nonlinear convection has occurred to reinforce the nanofluid motion and reduce the thermal boundary layer thickness. The results of this study are useful in polymer industries.

Stability analysis of dual solutions for nonlinear radiative magnetohydrodynamic flow of [formula omitted] hybrid nanofluid over a nonlinearly shrinking surface

The present work explores the existence and temporal stability of dual solutions with the consequence of nonlinear thermal radiation on hybrid nanofluid flow (including Silver and Titanium dioxide nanoparticles in water) past a permeable shrinking sheet. The analysis also considers the united outcomes of suction/injection, Joule heating, viscous dissipation, and magnetohydrodynamics. Employing realistic assumptions and suitable similarity transformations, the governing nonlinear partial differential equations are formulated and altered into a nonlinear ordinary differential equations system. These equations are then solved numerically using the Lobatto IIIA technique. It is observed that dual solutions can occur within a precise range of the shrinking surface parameter. Analyzing the temporal stability of these dual solutions under small disturbances shows that the upper solution branch is stable and represents a physically realistic solution to the problem. In contrast, the lower solution branch is unstable and not physically realizable. No solution exists beyond the critical λc=−1.3915 for the shrinking parameter. The critical values of shrinking parameter λc=−1.2565,−1.3188, and −1.4161 correspond to volume fractions of hybrid nanofluid with φAg−TiO2 of 2%,4%, and 8%, respectively. No solution exists beyond this critical point. The graphical representation and quantitative explanation demonstrate how various emergent characteristics affect momentum and thermal boundary layer profiles, Nusselt number, and skin friction. The velocity and temperature profile of hybrid nanofluid can be improved by adding a small volume of nanoparticle volume fraction. Thermal boundary layer thickness is amplified by an accumulation in the shrinking parameter, power index of velocity component, thermal radiation parameter, and temperature difference ratio. Sheering stress and heat transfer coefficient improve with adding more nanoparticles in the base fluid for the first solution braches, but opposite effects are found in the second solutions. The contributions of this research are significant both theoretically, in terms of advancing the mathematical modeling of hybrid nanofluid flow with heat transfer in engineering systems, and practically, in terms of applications to engineering cooling systems.

Enhancing the heat transfer in CuO-MWCNT oil hybrid nanofluid flow in a pipe

In this study, three-dimensional steady-state laminar flow simulations were conducted in a horizontal pipe using CuO and multi-walled carbon nanotubes (MWCNT) nanoparticles with engine oil as the base fluid. Various nanoparticle volume fractions were examined under a constant heat flux boundary condition applied to the pipe wall. The main goal was to assess and compare the effects of different nanoparticle volume concentrations, including CuO and MWCNT in ratios of 1:1 and 1:2, on convective heat transfer. A second-order discretisation method was employed for solving the equations, and the SIMPLE algorithm was used for pressure–velocity coupling in the CFD code. The study focused on the impact of nanoparticle volume fraction on the convective heat transfer coefficient and the Nusselt number at a Reynolds number of 750. The findings indicate that increasing the nanoparticle volume fraction enhances both the convective heat transfer coefficient and the Nusselt number, with MWCNT having a more pronounced effect compared to CuO. Specifically, adding 2% CuO increases the heat transfer coefficient by 65%, while a mixture of 1% CuO and 1% MWCNT boosts it by 75%. The thermal boundary layer thickness also grows with higher nanoparticle concentrations, with 1% CuO and 3% CuO increasing the thickness by 1.5% and 3.6%, respectively. A formula for the thermal boundary layer thickness in CuO-oil nanofluids is provided based on volume fraction, and a scale analysis of the average heat transfer coefficient confirms that the simulation results are consistent with this analysis.

Electromagnetic mixed convective flow of dusty hyperbolic tangent hybrid nanofluid over a stretching surface: A quadratic regression analysis using RSM

This article investigates the flow dynamics of electrically conducting dusty hyperbolic tangent fluid over a stretching sheet with thermal radiation and heat source effects. Moreover, the suspension of Aluminium oxide (Al2O3) and Tantalum nanoparticles in engine oil as base fluid at 300 K is considered. The flow and thermal dynamics are analysed using Xue and Hamilton Crosser's thermal conductivity models. Moreover, using various ranges, the effect of the Richardson number on forced, mixed and natural convection is examined. The governing partial differential equations of the flow model are converted into ordinary differential equations and then solved numerically using the boundary value problem solver BVP4C along with the shooting technique in MATLAB. The Xue model enhances the heat transfer rate by 3.55% compared to the Hamilton Crosser model ϕ1 = 0.03, ϕ2 = 0.01, R = 0.1, Q = 0.6, βt = 0.2, βv = 0.07. A moderate adjustment to the Richardson number can reduce skin friction by 0.889% in the case of forced convection. The absence of dust particles enhances the thermal and momentum boundary layer thickness. Tantalum nanoparticles outperform Al2O3 in terms of temperature and velocity. It is possible to regulate the temperature and velocity of the backflow by changing the heat source parameter and the nanoparticle volume percentage. The maximum achievable heat transfer rate in the fourth experimental run is 0.2609 when R = 2.5 and Q = 1.5 as determined by the quadratic regression analysis.

Flow analysis of water conveying nanomaterials over a rotating surface with thermal radiation

PurposeThe present findings aim to investigate the thermal behavior of water-based nanofluid flow over a rotating surface, focusing on understanding the effects of different types of nanoparticles on thermal efficiency, considering thermal radiation and variable viscosity effects. By considering four distinct nanoparticles – silicon dioxide titanium dioxide, aluminum oxide and molybdenum disulfide – the study aims to provide insights into how nanoparticle addition influences heat production, thermal boundary layer thickness and overall thermal performance.Design/methodology/approachThe study employs computational methods, utilizing the BVP mid-rich algorithm for the solution procedure. The computational approach allows for a detailed investigation of the thermal behavior of nanofluid flows across a rotating surface under varying conditions.FindingsThe study concludes that adding nanoparticles in the base liquid increases heat production in the system, resulting in enhanced thermal boundary layer thickness. The comparative analysis shows that different nanoparticle types exhibit varying effects on thermal efficiency, suggesting that careful selection of nanoparticles can optimize heat transport and thermal management processes. Moreover, there's a noteworthy uptrend in the radial velocity profile concerning the stretching parameter, whereas a converse trend is observed in the thermal profile.Originality/valueThis study contributes original insights by comprehensively investigating the thermal behavior of water-based hybrid nanofluid flow over a rotating surface.

Thermal analysis on Ferro Casson nanofluid flow over a Riga plate with thermal radiation and non-uniform heat source/sink

Ferro hybrid nanofluids can be used in electronics and microelectronics cooling applications to reduce heat accumulation and efficiently remove surplus heat. These nanofluids aid to maintain optimum operating temperatures and reduce device overheating by enhancing the heat transfer rate. With this motivation, the aim of the present numerical analysis is to study the three-dimensional incompressible hybrid nanofluid flow over a slippery Riga surface by combining the Casson fluid model. Mathematical modeling is constructed with nanoparticles as Fe3O4 and CoFe2O4 with base fluid as water. The non-uniform heat source/sink and thermal linear radiation effects are taken into account with the Hamilton–Crosser thermal conductivity model. A system of nonlinear PDEs is produced by the proposed problem and then the relevant similarity variables are implemented to transform the set of partial differential equations and their accompanying boundary conditions into the coupled nonlinear differential equations with one independent variable. These modified ordinary differential equations (ODEs) were then successfully solved with the Runge–Kutta fourth-order method by combining via the shooting technique. With the aid of graphical representations, the effects of various influencing parameters were presented and analyzed comprehensively. Furthermore, the impacts of relevant parameters on heat transfer rates and shear stress are concisely discussed and illustrated in tabular forms. The significant findings include the enhancement of the radiation parameter increases the thermal boundary layer thickness and the thickness increases whenever surface experiences slippery conditions. The axial and transverse momentum of the fluid are controlled with the Casson parameter. An effective connection is noticed once the current numerical solutions are verified under particular conditions that were previously described.

Non-Oberbeck–Boussinesq effects on a differentially heated vertical cavity with high-Prandtl number fluid

This study explores the non-Oberbeck–Boussinesq (NOB) effects on hydrodynamics and heat transport in two-dimensional glycerol-filled differentially heated vertical cavity (DHVC). The simulations span Rayleigh numbers (Ra) from 2×103 to 5×109 and temperature difference (Δθ̃) up to 50 K at a Prandtl number (Pr) of 2547. We showed the emergence of stratified flow structures, delineated the NOB effects on temperature distribution symmetry, and analyzed the scaling behaviors of the Nusselt number (Nu), Reynolds number (Re), and thermal boundary layer (BL) thicknesses (λ¯hθ and λ¯cθ) against Ra. For Ra≥3×105, the stratification number (S) shows reduced sensitivity to changes in Ra, stabilizing around 0.5. Additionally, the center temperature (θcen) appears to be unaffected by Ra and increases linearly with Δθ̃ for Ra>106, satisfying θcen≈2.99×10−3K−1Δθ̃. Our results also revealed that Nu∼Raγ Nu and Re∼RaγRe with 0.2649≤γ Nu≤0.2654 and 0.3633≤γ Re≤0.3643, respectively, where γ Nu and γ Re exhibit a monotonic decrease as NOB effects intensify. For all investigated Ra values, NuNOB/NuOB<1 and ReNOB/ReOB>1 hold consistently, with deviations from OB predictions capped at 6.38% and 2.63% for Ra≥108, respectively. The analysis of thermal BL thickness reveals distinct scaling behaviors, characterized by λ¯h,cθ∼Raγ λ¯ h, c, with scaling exponents ranging from −0.2690 to −0.2669 for both OB and NOB scenarios. Notably, it reveals a divergence from water-based DHVC trends, showing linear decreases in the hot wall's scaling exponent and increases for the cold wall.

Experimental and numerical study of structural parameters on the heat transfer performance of submerged cooling system

Immersion direct contact cooling effectively transfers heat from electronic components to a cooling solution without additional thermal resistance, due to its high energy density, low power consumption, system simplicity, and integrated thermal management for electronic devices. Current scholarly research on immersed structures predominantly focuses on surface temperature effects, with a scant investigation into internal flow and temperature field distributions concerning boundary layers. This study addresses structural optimization in immersion cooling systems, employing experimental and simulation methods to elucidate the thermal mechanisms by which structural optimization impacts the performance of chip immersion cooling systems. The research examines the impact of panel spacing and liquid level height on the thickness of velocity and thermal boundary layers, as well as the combined effects of natural and forced convection under three distinct cooling modes. Analysis reveals that heat pipe immersion cooling can reduce the heat source junction temperature to 40.7 °C under a 60 W power dissipation, a 47.2 % decrease from the bare heat source temperature. Reducing panel spacing disrupts the thermal boundary, enhancing forced convection and lowering the junction temperature by up to 10.1 % (6.5 °C). As liquid level height increases, the junction temperature initially decreases and then rises, with an optimal height of 175 mm for the best overall heat transfer effect. At low flow velocities (0.04 m/s), the vertical buoyancy-induced flow velocity at the heat source surface (24.2 × 10-6 m/s) exceeds the horizontal forced convection velocity (0.78 × 10-6 m/s), indicating that buoyancy changes due to density differences are significant and must be considered.

Computational micropolar model of hybrid nanofluid flow across a wedge

Non-Newtonian flow from wedges is a vital problem in coatings, polymer processing etc. Hence the main aim is to investigate the convective boundary layer flow of micropolar hybrid nanofluid (MHN)from a wedge. It is assumed that the wedge surface is isothermal. The Eringen model is employed to define micropolar fluid. Nanoscale Tiwari–Das formulations are used to study the specific effects of nanoparticles and volume fractions. The dimensionless boundary value problem arises by suitable coordinate transformations as a system of nonlinearly coupled ordinary differential equations. The so-called Falkner Skan flow case is resolved. Dimensionless, transformed, coupled momentum, microrotation, boundary layer equations are resolved using the numerical scheme MATLAB bvp4c. The parameteric investigations are performed on hybrid nanofluids using water as the basis liquid and varying volume fractions from 0 to 8%. Affirmation with previous work is done. The consequence of Eringen micropolar parameter, Hartree pressure gradient parameter, nanoparticle volume fraction, Eckert number, heat absorption (sink) parameter, on the flow and physical characteristics are visualized graphically and in tables. With rising material factor and volume fraction of nanoparticle, temperature is markedly enhanced. Increases in volume fraction dampen angular velocity close to the wedge surface, while farther from the wall, the opposite effect is seen. Temperature and thermal boundary layer thickness are both greatly enhanced by increasing Eckert number. With an increase in the volume proportion of nanoparticles, velocity decreases. Heat generation raises temperatures while a heat sink lowers them. The pressure gradient parameter increases skin friction while decreasing Nusselt number. Nusselt number for hybrid nanofluid is higher than for nanofluid.

On the dual diffusion flow of Powell–Eyring hybrid nanofluid with motile microorganism and non-uniform heat source using Darcy–Forchheimer model

This communication elaborates the rheological behavior of bioconvection flow of Powell–Eyring hybrid nanofluid over a stretchable heated cylinder embedded in Darcy–Forchheimer porous medium. The single and two-phase nanofluid models are used as mixture model by taking volumetric friction and dual diffusion of injected nanomaterial’s, while the Buongiorno model takes the dual diffusion of nanomaterials, allowing us to evaluate the thermophoresis and Brownian diffusion properties. The governing equations are solved with an efficient Runge–Kutta–Fehlberg numerical technique. The effects of appropriate parameters on flow, temperature, concentration, and motile microorganism. Our findings reveal that the fluid velocity increases with curvature parameter, while detract with Darcy and porosity parameter. Temperature is increasing function of Brownian, thermophoresis and heat source parameters. The concentration and motile profile increases with curvature parameter. An escalating trend for energy and mass transport was seen against curvature and thermophoresis parameter. Higher values of Curvature and Schmidt number depict positive impact on nanoparticle concentration, while the results for chemical reaction are conflicting. An increasing value of Brownian and thermophoresis parameters promote higher temperature. The temperature and thermal boundary layer thickness are also affected by the heat source and sink parameters in opposite manner.

An analytical study on the influence of magnetic field-dependent viscosity on viscous and ohmic dissipative second-grade fluid boundary layers

This article aims to investigate the magnetohydrodynamic (MHD) boundary layer flow of a second-grade non-Newtonian fluid over a horizontally stretching sheet, considering magnetic field-dependent (MFD) viscosity, as well as viscous and Ohmic dissipations. Analytical solutions for previously unexplored momentum and heat transfer equations involving MFD viscosity are derived. Two boundary conditions, namely Prescribed Surface Temperature (PST) and Prescribed Heat Flux (PHF), are taken into account. Governing dimensional partial differential equations (PDEs) are transformed into non-dimensional ordinary differential equations (ODEs) using similarity transformations. Closed-form analytical solutions for flow are derived, considering stretching velocity, MFD viscosity, second-grade fluid properties, and suction impacts. Heat transfer equations are transformed into Gauss-hypergeometric form, yielding solutions in terms of confluent hypergeometric functions. Analytical expressions for skin friction, local Nusselt number, and non-dimensional wall temperature are derived. A unique solution is obtained for the flow equation. It is found that both second-grade and magnetic viscosity parameters expand the momentum boundary layer while the magnetic parameter reduces thickness. Thermal boundary layer thickness increases with a higher second-grade parameter, magnetic viscosity, and Eckert number. Moreover, analytical solutions are validated against published results for a special case.

Nanoparticle aggregation kinematics and nanofluid flow in convectively heated outer stationary and inner stretched coaxial cylinders: Influenced by linear, nonlinear, and quadratic thermal radiation

The consequence of nanoparticle aggregation and convective boundary condition on the nanofluid stream past the co-axial cylinder with radiation impact is investigated in the present examination. The influence of linear, nonlinear, and quadratic thermal radiation on the nanofluid flow is analyzed. The outer cylinder stays stable, while the inner cylinder deforms horizontally in the axial direction, allowing fluid to flow. By using similarity variables, the governing equations are transformed into ordinary differential equations (ODEs). Subsequently, the Runge–Kutta–Fehlberg fourth-fifth order (RKF-45) method is employed to solve the reduced ODEs. The upshot of several nondimensional terms on the temperature and velocity profiles is displayed with graphical representation. The comparison of linear, quadratic, and nonlinear thermal radiation on the thermal profile is illustrated. The upsurge in curvature parameter increases velocity and thermal profile. The increase in radiation parameter intensifies the temperature profile. The thermal profile improves with a rise in the values of radiation parameter. The radiation parameter generates thermal energy in the flow zone, which is why the temperature field has improved. The thermal Biot number exhibits an increasing response with temperature and thermal boundary layer thickness. The linear thermal radiation shows better heat transfer compared to quadratic and nonlinear thermal radiation.

Impact of the Stefan gusting on a bioconvective nanofluid with the various slips over a rotating disc and a substance-responsive species

This paper presents thorough computational and theoretical analyses of steady forced convective flow over a rotating disc submerged in a water-based nanofluid containing microorganisms. It delves into the examination of boundary layer flow characteristics of a viscous nanofluid, considering Stefan blowing effects and multiple slip conditions influenced by a magnetic field. Notably, the study accounts for novel aspects such as thermal radiation and both constructive and destructive chemical reactions. The movement of nanoparticles is elucidated based on thermophoresis and microscopic behaviors, while changes in volume fraction do not affect the thermo-physical properties of the nanofluid. To address the altered nonlinear set of differential equations, an effective numerical approach, the Keller-Box method, is implemented for critical and efficient solutions. These appropriate transformations are defined and applied. When compared to blowing suction, it shows a better enhancement in the rate of heat transfer, mass, and microorganisms. Some of the main observations are there is a decrease in wall skin friction in the directions of radial and tangential as magnetic field strength is increased. The evaluation of thermal boundary layer thickness and temperature is noted for the radiation parameter (Rd) improvement. The present analysis has applications in electromagnetic micro-pumps and nanomechanics. As to the applications in the science and engineering fields, technologies such as micro-electromechanical systems-based microfluidic devices and microfluidic-related technologies will be accepted.

Melting heat transfer features in a B[formula omitted]dewadt flow of hybrid nanofluid ([formula omitted]/water) by a stretching stationary disk

The melting impacts on the three-dimensional hybrid nanofluid flow by a stationary stretching disk is examined. The flow configuration is due to the stretching of the disk. The magnetic field is applied normal to the disk in order to generate the resistance in the liquid. The performance of heat transfer in the liquid, the thermal radiation and heat generation/absorption impacts are taken into consideration. The melting heat transfer impact on the surface is analyzed here. The impact of stretching and rotating mechanisms along with applied physical impacts on the hybrid nanofluid flow and heat features are of the present concern for this physical problem. A conventional transformation is presented to lead to a set of coupled similarity equations which are highly non-linear in nature. A numerical method subject to bvp4c technique is adopted for the solution process. Results reveal that increasing trend of stretching of the disk lowers the boundary layer thickness and consequently highers the rate of heat transfer. It is found the reduction in thickness of thermal boundary layer by the strength of stretching. Additionally, the temperature distribution rises by the influence of melting temperature. Further, the skin fraction coefficient seen to be enhanced with the enlargement of nanoparticles volume fraction.

Consequences of higher order chemical reaction on bioconvective carbon nanotubes flow implementing Buongiorno's model

In recent years, carbon nanotubes have been extensively explored based on numerous applications in fields such as carbon nanotube based electrodes, super capacitors, nanowires, sensors, coating with polymers, biomedical, and mechanical applications. Keeping in view the significance of carbon nanotubes in the heat transfer process in micro-electrochemical systems, this study is conducted to examine the heat transfer attributes of the carbon nanotubes using the mixture base working fluid. The focus of this investigation is to elaborate the consequence of higher chemical reactions on the bioconvective flow of carbon nanotubes. Additionally, modified Buongiorno's nanofluid model has been used, which undertakes thermophoresis and Brownian motion effects. Heated boundary condition has also been incorporated with the migration of motile microorganisms. The hybrid nanofluid mechanism has been followed in this work. Carbon nanotubes of single-layer and multi-layer have been used simultaneously with different working fluids, such as ethylene glycol (EG) and ethylene glycol/water (EG-water). Non-dimensional flow model equations have been tackled with the bvp-4c package. The obtained outcomes have been presented for distinct profiles and tabulated data sets for the surface skin friction and heat transfer coefficient. It has been observed that when the level of Brownian motion increases, the velocity profile decreases abruptly for SWCNT-MWCNT/EG as compared to SWCNT-MWCNT/EG-water hybrid nanofluid. Opposite behavior has been seen with raising values of magnetization. High Prandtl number decrease thermal boundary layer thickness for both types of hybrid nanofluids. The motile microorganism profile expands by raising the level of bioconvective Lewis number. Moreover, the outcomes of drag force and Nusselt number have been compared, and good agreement has been found.

Numerical study of hybrid binary Al2O3-Cu-H2O nanofluid coating boundary layer flow from an exponentially stretching/shrinking perforated substrate with Cattaneo-Christov heat flux, heat source, suction and multiple slip effects

Modern coating systems are increasingly deploying nanomaterials which offer improved thermal performance. The optimization of these systems can benefit from more elegant fluid dynamic models of the coating process. Inspired by these advancements, the present investigation introduces a novel mathematical model to analyze the boundary layer transport in Al2O3-Cu-H2O hybrid binary nanofluid coating deposition on an exponentially stretching porous substrate (sheet). Lateral mass flux (suction) at the wall is also considered a heat source (generation) for hot spot manufacturing effects. To add further sophistication to the thermal conduction model, a non-Fourier approach is adopted which accurately incorporates thermal relaxation effects i.e. the Cattaneo-Christov heat flux (CCHF) model. The Tiwari-Das volume fraction nanoscale formulation is implemented for different combinations of Alumina (Al2O3) and Copper (Cu) metallic nanoparticles in an aqueous base fluid (H2O). Hydrodynamic wall and thermal slip are also included as they feature in coating processes. The fundamental equations governing mass, momentum, and energy conservation, along with the corresponding conditions at the wall (substrate) and free stream, are made dimensionless through suitable scaling similarity transformations. The resulting nonlinear coupled ordinary differential boundary value problem is subsequently addressed using the efficient MATLAB bvp4c routine. Special cases of the non-Fourier model are validated against published results, and the general model is further confirmed through validation using an Adams-Moulton 2-step predictor-corrector algorithm (AMPC). Furthermore, dual solutions of the generalized model are extracted and visualized. A comprehensive study of the effects of key thermophysical key parameters on momentum and thermal characteristics (velocity, temperature, skin friction and local Nusselt number) is conducted and solutions are visualized graphically. The computations show that higher temperatures are present with intensification in the thermal relaxation parameter (Cattaneo-Christov hyperbolic model parameter), which predicts therefore larger temperatures than the classical Parabolic heat conduction model using Fourier analysis. Effectively, thermal relaxation is responsible for finite heat wave propagation and produces more accurate estimations of heat transfer than the Fourier model. An increase in stretching parameter enhances the skin friction coefficient and elevates the local Nusselt number. As the thermal relaxation parameter increases, the temperature magnitudes corresponding to the first and second solutions are both enhanced as are thermal boundary layer thicknesses. An increase in wall suction induces an escalation in the first solution for velocity whereas it reduces the second solution velocity. Stronger wall suction suppresses temperatures. With increasing thermal slip, the boundary layer is cooled i.e. temperature plummets and thermal boundary layer thickness is decreased. Strong deceleration is induced with greater hydrodynamic (velocity) slip. Both first and second solutions for skin friction are elevated with shrinking whereas they are depressed with stretching. With greater velocity slip both the first and second solutions for skin friction are depleted with greater velocity slip for the shrinking case, whereas they are generally enhanced for the very strong stretching case. The computations offer some new insights into multi-physical thermal fluid dynamics of nanofluid-based coating systems.

Nonlinear heat radiation and mass transfer characteristics on MHD Walters’ B fluid flow through a porous medium over a stretching sheet

To handle the continuous thermal power supply is very important in thermal systems and industries, so magnetized heat transport with non-Newtonian fluid is an appropriate platform for thermal power energy. In view of this usefulness, this paper provides a numerical assessment of electrically conducting Walter's B fluid flow through nonlinear permeable stretching sheet subject to mixed convective, porous medium, and Newtonian heating phenomena. Thermophoresis and Brownian motion effects have been included in energy and species diffusion equations to account for the impacts of nonlinear thermal radiation, joule heating, heat source and chemical reaction. The system of governing equations has been reduced to dimensionless nonlinear coupled equations using similarity transformations. The bvp4c technique has been used to obtain the solution for velocity, temperature, and concentration distributions. We consider both regions of assisting and opposing flow and provide various tables and graphs to examine the impact of varying values of emerging factors. Heat source and thermal radiation characteristics are found to enhance the thermal boundary layer thickness, which may be used to dissipate heat. The magnetic parameter augmented the fluid temperature and decelerated the velocity field. The chemical reaction parameter accelerated the concentration distribution. Further, the Sherwood number, Nusselt number, and skin friction coefficient have been determined and compared well to prior research that has been published.

Insight of Jeffrey flow over a stretching Riga plate with activation energy and viscous dissipation: Melting heat transfer regime

AbstractPresent article highlights the significance of Arrhenius activation energy along with viscous dissipation in Jeffrey fluid over a Riga plate. Riga plate is basically an actuator made up of array of magnets and electrodes scaled on a plane surface to tackle the weaker electrical conductivity during fluid flow. In order to ensure the novelty, a reliable melting heat surface condition has been incorporated on nonlinear stretching Riga plate of variable thickness to reconnoiter features of heat transfer. Moreover, stagnation point has been retained in this study. Adequate transformations are employed in order to attain system of nonlinear ordinary differential equations. A well known semi analytical technique (Homotopy analysis method) is utilized to obtain series solutions of prevailing dimensionless equations. Influence of several apposite parameters on velocity, thermal and concentration distributions is analyzed graphically. Physical evaluation and graphical sketch is presented for drag force coefficient and rate of heat transfer. Analysis of velocity as well as associated boundary layer thickness gives the growing up impact for the strength of modified Hartmann number. Enhancement of dimensionless reaction rate and endothermic/exothermic reaction parameter results in increment for heat flux over stretching Riga plate. Increase in thermal distribution takes place for higher Eckert number while thermal boundary layer thickness depicts opposite trend in this case. Concentration boundary layer thickness enhances while concentration profile declines for higher Schmidt number. Velocity distribution is found to be incremented for intense melting process. Higher dimensionless activation energy parameter is analyzed to be responsible for growing up concentration field.