Operation Of Terahertz Quantum Cascade Lasers Research Articles

Negative free carrier absorption in terahertz quantum cascade lasers

We analyze the peculiar case where the free carrier absorption arising from LO phonon absorption-assisted transitions becomes negative and therefore turns into a gain source for quantum cascade lasers. Such an additional source of gain exists when the ratio between the electronic and the lattice temperatures is larger than one, a condition that is usually fulfilled in quantum cascade lasers. We find a gain of few cm−1's at 200 K. We report the development of a terahertz quantum cascade laser operating in the negative free carrier absorption regime.

High-temperature, continuous-wave operation of terahertz quantum-cascade lasers with metal-metal waveguides and third-order distributed feedback

Currently, different competing waveguide and resonator concepts exist for terahertz quantum-cascade lasers (THz QCLs). We examine the continuous-wave (cw) performance of THz QCLs with single-plasmon (SP) and metal-metal (MM) waveguides fabricated from the same wafer. While SP QCLs are superior in terms of output power, the maximum operating temperature for MM QCLs is typically much higher. For SP QCLs, we observed cw operation up to 73 K as compared to 129 K for narrow (≤ 15 μm) MM QCLs. In the latter case, single-mode operation and a narrow beam profile were achieved by applying third-order distributed-feedback gratings and contact pads which are optically insulated from the intended resonators. We present a quantitative analytic model for the beam profile, which is based on experimentally accessible parameters.

Coherent sampling of active mode-locked terahertz quantum cascade lasers and frequency synthesis

Researchers demonstrate a terahertz quantum cascade laser operating in a regime of active mode-locking by modulating its bias current with a radiofrequency synthesizer. This technique allows coherent sampling of the terahertz electric field as well as control over the laser's carrier–envelope phase shift.

186 K operation of terahertz quantum-cascade lasers based on a diagonal design

Resonant-phonon terahertz quantum-cascade lasers operating up to a heat-sink temperature of 186 K are demonstrated. This record temperature performance is achieved based on a diagonal design, with the objective to increase the upper-state lifetime and therefore the gain at elevated temperatures. The increased diagonality also lowers the operating current densities by limiting the flow of parasitic leakage current. Quantitatively, the diagonality is characterized by a radiative oscillator strength that is smaller by a factor of two from the least of any previously published designs. At the lasing frequency of 3.9 THz, 63 mW of peak optical power was measured at 5 K, and approximately 5 mW could still be detected at 180 K.

Operation of terahertz quantum-cascade lasers at 164 K in pulsed mode and at 117 K in continuous-wave mode

We report the demonstration of a terahertz quantum-cascade laser that operates up to 164 K in pulsed mode and 117 K in continuous-wave mode at approximately 3.0 THz. The active region was based on a resonant-phonon depopulation scheme and a metal-metal waveguide was used for modal confinement. Copper to copper thermocompression wafer bonding was used to fabricate the waveguide, which displayed improved thermal properties compared to a previous indium-gold bonding method.

Terahertz quantum-cascade laser operating up to 137 K

We report operation of a terahertz quantum-cascade laser at 3.8 THz (λ≈79 μm) up to a heat-sink temperature of 137 K. A resonant phonon depopulation design was used with a low-loss metal–metal waveguide, which provided a confinement factor of nearly unity. A threshold current density of 625 A/cm2 was obtained in pulsed mode at 5 K. Devices fabricated using a conventional semi-insulating surface-plasmon waveguide lased up to 92 K with a threshold current density of 670 A/cm2 at 5 K.

Continuous-wave operation of terahertz quantum-cascade lasers

We report continuous-wave (CW) operation of a 4.4-THz quantum-cascade laser grown in the GaAs-AlGaAs materials system by molecular beam epitaxy. The device operates at 4 K with a threshold current of 160 mA, and an output power of ∼25 μW. In pulsed mode, the maximum operating temperature is 52 K, with a threshold current of 108 mA at 4 K. CW lasing was achieved by using a small cavity ridge area (60×600 μm), and by coating one of the laser facets. These two features allowed for a substantial decrease of the threshold current and therefore reduced detrimental heating effects. The role played by the lateral resistance of the 800-nm GaAs layer underneath the active region was also investigated. Experimental data is presented showing that the temperature of the active region, which eventually hinders CW lasing, can be substantially influenced by the value of this lateral resistance.