Tensile Relaxation Research Articles

Multiscale revelation of asphalt morphology and adhesion performance evolution during stress relaxation process

The objective of this study is to investigate the evolution of asphalt morphology and adhesion properties during stress relaxation using atomic force microscopy (AFM) and molecular dynamics (MD) simulations. Changes in surface roughness, Derjaguin-Muller-Toporov (DMT) modulus, adhesion force, and force-distance curves were analyzed. Morphological and adhesion property evolution was assessed using correlation length and Lyapunov exponent. MD simulations provided insights into the internal stress-time relationship and free volume fraction of asphalt during relaxation. Results indicate that under constant tensile strain, the “bee structure” on the asphalt surface elongates, dark pits transform into light protrusions, microcracks heal, and surface roughness stabilizes after 10 h. Under compressive strain, similar changes occur but are more pronounced during tensile relaxation. The combined use of AFM and MD simulations offers a comprehensive understanding of the microscopic evolution mechanisms of asphalt under stress relaxation, providing valuable insights for optimizing asphalt pavement design and maintenance.

Effect of temperature and humidity on mechanical properties and constitutive modeling of pressure-sensitive adhesives

Pressure-sensitive adhesives (PSAs) are crucial for the structural and functional integrity of flexible displays. Investigating the intricate mechanical properties of PSAs can help enhance product quality and performance. This study conducts systematic mechanical tests, including uniaxial tensile, compression, planar shear, and stress relaxation, on PSAs at temperatures ranging from – 25 to 85 ℃ and relative humidity levels from 0 to 90%. Our findings reveal that the Anssari-Benam model accurately describes the hyperelastic behavior of PSA materials under large deformation, outperforming the Ogden model by requiring fewer parameters and better preserving convexity. Moreover the results show that temperature markedly affects PSA properties, particularly near the glass transition temperature (Tg), with lower temperatures leading to decreased elasticity and higher temperatures aiding in stress relaxation. Similarly, humidity impacts PSA behavior, increasing elasticity and decreasing stiffness, especially noticeable in stress relaxation tests. These findings highlight the substantial influence of environmental conditions on the material properties of PSAs and underscore the necessity of understanding both hyperelastic and viscoelastic responses for their application in flexible technologies. This research provides critical insights for the optimal utilization of PSAs in the rapidly evolving field of flexible electronics, including OLED displays.

Thermo-Chemo-Mechanical Modeling of Residual Stress in Unidirectional Carbon Fiber-Reinforced Polymers during Manufacture.

The application of carbon fiber-reinforced composite materials in marine engineering is growing steadily. The mechanical properties of unbonded flexible risers using composite tensile armor wire are highly valued. However, the curing process generates a certain amount of internal residual stress. We present a detailed analysis of epoxy resin laminates to assess the impact of thermal, chemical, and mechanical effects on the curing stress and strain. An empirical model that correlates temperature and degree of cure was developed to precisely fit the elastic modulus data of the curing resin. The chemical kinetics of the epoxy resin system was characterized using differential scanning calorimetry (DSC), while the tensile relaxation modulus was determined through a dynamic mechanical analysis. The viscoelastic model was calibrated using the elastic modulus data of the cured resin combining temperature and degree of the curing (thermochemical kinetics) responses. Based on the principle of time-temperature superposition, the displacement factor and relaxation behavior of the material were also accurately captured by employing the same principle of time-temperature superposition. Utilizing the empirical model for degree of cure and modulus, we predicted micro-curing-induced strains in cured composite materials, which were then validated with experimental observations.

Influence of Cold Wave Diversities on Thermal Stress and Thermal Fatigue Life of Asphalt Mixture.

Apart from low-temperature cracking, asphalt pavement may also suffer from thermal fatigue cracking. To clarify the impact of cold waves on the thermal fatigue performance of asphalt mixtures, the typical atmospheric temperature characteristics of different regions in China from 2012 to 2019 were analyzed, and the frequency of cold waves in these regions was determined. The viscoelastic parameters of an asphalt mixture are determined through an indirect tensile relaxation test. The thermal stress of the asphalt mixture is simulated and analyzed by using the finite element method. The effect of cold waves on the thermal fatigue life of the asphalt mixture was evaluated. The results show that the frequency of cold waves is different from region to region in China, and the cold waves mainly occurred from October of one year to February of the next year. Northeast China has the most frequency and the largest temperature drop amplitude, followed by North China. The maximum thermal stress increases with the decrease in temperature drop and initial temperature and is unrelated to the duration of cold waves. The thermal stress calculated based on the atmospheric thermal boundary is higher than the value using the road surface temperature. The thermal fatigue lives of asphalt mixtures in North China and Northeast China are very short, while the thermal fatigue life of the mixture in Central China is the longest. To meet the requirement of thermal fatigue damage caused by cold waves during the designed service stage, the recommended threshold for thermal stress is 0.39-0.77 MPa.

Multiscale residual stress and mechanical behavior analysis in machining of Ti-6Al-4V alloy with advanced microscopic characterization

Machining of polycrystalline metal materials results in metallurgical modifications in the machined surface, and it can introduce multiscale residual stresses (macroscale and microscale residual stress), which may be detrimental to the mechanical properties thereby interfering with the service performance of machined parts. However, most of the current studies only focus on the macroscale residual stress, the microscale residual stresses have always been neglected since the limitations of the commonly used techniques for residual stress measurement in machined surfaces. In this study, the recently developed Focused Ion Beam-digital image correlation (FIB-DIC) ring core method was employed to evaluate the time-resolved strain relaxation and multiscale residual stress of the machined surface under different cutting conditions. The quantitative evaluation of residual stress and microstructural effects on hardness of the machined surface was conducted by combining with FIB incremental milling and nanoindentation technique. It has been observed that although the global tensile strain relaxation was captured in the ring-core region, local microscale compressive strain relaxation also occurred. The hardness of the machined surface was determined by the combined effects of microstructure and residual stress induced by machining. Specifically, the grain refinement and compressive residual stress contributed to hardening, while tensile residual stress resulted in softening of the machined surface. Furthermore, it was also observed the hardening/softening effects were enhanced with increasing intensity of tension and compression.

The mechanical properties of different cross-veins in the hind wing of locust Locusta migratoria under uniaxial tensile and stress relaxation tests.

Locust Locusta migratoria exhibits remarkable aerial performances, relying predominantly on its hind wings that generate most of lift and thrust for flight. The mechanical properties of the cross-veins determine the deformation of the hind wing, which greatly affect the aerodynamic performance of flapping flight. However, whether the mechanical behaviours of the locust cross-veins change with loading rate is still unknown. In this study, cross-veins in four physiological regions (anterior-medial, anterior-lateral, posterior-medial and posterior-lateral) of the hind wing from adult locusts were investigated using uniaxial tensile test, stress relaxation test and fluorescence microscopy. It was found that the cross-veins were a type of viscoelastic material (including rate-independent elastic modulus and obvious stress relaxation). The cross-veins in the two anterior regions of the hind wing had significantly higher elastic moduli and higher ultimate tensile stress than those of its two posterior regions. This difference might be attributed to different resilin distribution patterns in the cross-veins. These findings furnish new insights into the mechanical characteristics of the locust cross-veins, which might deepen our understanding of the aerodynamic mechanisms of locust flapping flight.

Understanding the radial contraction and axial mechanical responses of carbon nanotube yarns under axial tensile loading

Carbon nanotube yarns (CNTYs) are hierarchical fibers with outstanding mechanical and electrical properties, with promising applications in the composite industry and as smart materials. In situ scanning electron microscopy observations are performed herein on individual dry-spun CNTYs during axial tensile testing in order to study their radial contraction response and structural changes. The CNTYs exhibited significant diameter reduction and untwisting due to the rearrangement of their fibrils during axial loading. In situ measurements of CNTY diameter reduction led to an exponential decrease of the radial contraction ratio with axial strain, with average values ranging between 5.43 and 1.08. The major failure mechanism was identified as fibril pull-out triggered by fibril slipping. The simultaneous stress and electrical resistance decay of CNTYs under axial tensile relaxation tests fit to a Wiechert's viscoelastic model using a Prony series. The rate of exponential decrease of the electrical resistance over time, however, is slower than that of the stress relaxation, indicating that additional charge carrier relaxation phenomena are present. Using the measured structural and material data input, a nonlinear analytical model based on classical theory of staple yarns is able to reproduce the mechanical response of the yarn. The model suggests that the most prominent parameters affecting the axial mechanical response of the CNTY are the radial contraction ratio, the slip factor, fibril radius, and fibril length.

Strain-rate sensitivity analysis of microwave processed polypropylene-carbon nanotube composites

The study investigates the strain rate sensitivity of microwave-processed polypropylene nanocomposites containing a 10% volume fraction of multi-walled carbon nanotubes (MWCNTs), synthesized using a domestic microwave applicator (DMA). Through experimental analysis under various loading conditions including tensile, flexural, and multistep relaxation loads, the mechanical strength of these nanocomposites is assessed alongside destructive testing and scanning electron microscopy (SEM) results. Mathematical models are proposed to elucidate the mechanical response under different strain rate loadings. The nanocomposite exhibits elastoplastic behavior, with maximum elongation observed at a strain rate of 3 mm/min. During uniaxial tension tests, the ultimate strength increases significantly from 5.74 MPa at 1.52 mm/min to 13.8 MPa and 15.7 MPa at 1 mm/min and 2 mm/min respectively during multistep relaxation tests. The true stress-true strain curve follows a power law of strain hardening under high strain rate tensile tests. Flexural tests reveal maximum flexural strength and modulus at a strain rate of 1.25 mm/min, with elongation peaking at 1.50 mm/min. Mechanical properties, including modulus and ultimate strength, show an increasing trend with strain rate until a limiting value is reached, beyond which thermal softening occurs. SEM fractography illustrates the random and spatial distribution of CNTs at low strain rates, whereas agglomeration and CNT pull-out are observed at higher strain rates. This comprehensive analysis sheds light on the intricate mechanical behavior of microwave-processed polypropylene nanocomposites, offering insights into their potential applications and optimization strategies.

Characterization of Potting Epoxy Resins Performance Parameters Based on a Viscoelastic Constitutive Model.

To describe the evolution of residual stresses in epoxy resin during the curing process, a more detailed characterization of its viscoelastic properties is necessary. In this study, we have devised a simplified apparatus for assessing the viscoelastic properties of epoxy resin. This apparatus employs a confining cylinder to restrict the circumferential and radial deformations of the material. Following the application of load by the testing machine, the epoxy resin sample gradually reduces the gap between its surface and the inner wall of the confining cylinder, ultimately achieving full contact and establishing a continuous interface. By recording the circumferential stress-strain on the outer surface of the confining cylinder, we can deduce the variations in material bulk and shear moduli with time. This characterization spans eight temperature points surrounding the glass transition temperature, revealing the bulk and shear relaxation moduli of the epoxy resin. Throughout the experiments, the epoxy resin's viscoelastic response demonstrated a pronounced time-temperature dependency. Below the glass transition temperature, the stress relaxation response progressively accelerated with increasing temperature, while beyond the glass transition temperature, the stress relaxation time underwent a substantial reduction. By applying the time-temperature superposition principle, it is possible to construct the relaxation master curves for the bulk and shear moduli of the epoxy resin. By fitting the data, we can obtain expressions for the constitutive model describing the viscoelastic behavior of the epoxy resin. In order to validate the reliability of the test results, a uniaxial tensile relaxation test was conducted on the epoxy resin casting body. The results show good agreement between the obtained uniaxial relaxation modulus curves and those derived from the bulk and shear relaxation modulus equations, confirming the validity of both the device design and the testing methodology.

Surface disinfection change the mechanical, structural and biological properties of flexible materials used for additive manufacturing of medical devices

Additive manufacturing (AM) is a versatile technology with potential applications in healthcare and medical instruments, where surface disinfection or sterilization is essential. This study comprehensively the effect of commonly used cost-effective disinfectants, ethanol (70 V/V%) and chlorine solution on the mechanical and thermal properties of flexible 3D printed materials. The following materials were tested before and after a 5-cycle surface disinfection: Flexfill TPE 90A, Phyton Flex (TPU) for material extrusion, Flexible (resin), Elastic 50A (resin) for vat photopolymerization and Flexa Black (TPU) material for powder bed fusion technology. Mechanical tests included tensile, compression, Charpy impact, flex resistance and stress relaxation tests, as well as Shore A hardness and volume measurements. The structure was analyzed using scanning electron microscopy (SEM)and Raman spectroscopy. The cytotoxicity was assessed using a A549 cell viability assay. The results show that after disinfection, significant changes occurred mainly in the tensile and Shore A properties, such as the tensile strength of the disinfected Flexible (resin) materials was 3.44 MPa ± 0.51 MPa (ethanol) and 2.62 MPa ± 0.31 MPa compared to the native 2.02 MPa ± 0.24 MPa. Interestingly, the applied surface disinfectants can negatively affect biocompatibility. Medical devices have been designed and fabricated based on the findings. Our findings can serve as a guide to the potential applications of commonly used 3D printed flexible materials in the biomedical field.

A numerical model for stress relaxation analysis of sealing systems in nonbonded pipe end fittings

Nonbonded flexible pipes consist of polymer materials that experience stress relaxation at high temperatures, which ultimately affects the sealing performance of end sealing systems. To assess stress relaxation curves under varying temperatures and pre-strains, this paper conducts both tensile and stress relaxation tests on PVDF materials. To describe the stress relaxation characteristics of these materials, the Prony series is utilized. In order to identify the parameters of the series, the paper employs the Levenberg-Marquardt method of nonlinear regression. A finite element model is established to verify the accuracy of the parameter identification method. Subsequently, the paper establishes a two-dimensional axisymmetric finite element model of the sealing system in the end fitting, while taking into account fluid pressure inside the pipeline using a pressure penetration method. The impact of stress relaxation on the sealing performance is then discussed. Finally, the paper alters the coefficients of the Prony series to explore their significance on the sealing performance of the sealing system.

Impact of epitaxial strain relaxation on ferromagnetism in a freestanding La2 / 3Sr1 / 3MnO3 membrane

Manganite perovskites host emerging physical properties of strongly-correlated electrons with charge, spin, and lattice degrees of freedom. Using the epitaxial lift-off technique, we report enhancement of saturation magnetization and the ferromagnetic transition temperature of freestanding La2/3Sr1/3MnO3 membrane compared with as-grown film on SrTiO3 substrate involving lateral tensile strain. Structural analysis reveals shrinkage of unit-cell volume by tensile strain relaxation in the freestanding membrane, which causes enhancement of the ferromagnetic interaction. The impact of the microscopic lattice deformation on the ferromagnetism of La2/3Sr1/3MnO3 indicates a high potential of this material for flexible electronics applications with intriguing functionalities in strongly-correlated electron systems.

Viscosity mechanism of perfluorosulfonic acid-based materials and their application in proton exchange membrane fuel cells

Perfluorosulfonic acid (PFSA) ionomers and their composites are popular electrolyte materials for proton exchange membrane fuel cells (PEMFCs), which subject to the combined actions associated with humidity change, temperature cycling, and clamp force during long-time operation. Thus, their time-related mechanical behaviour can greatly affect their proton conductivity and material degradation. Because viscosity is a vital factor controlling the mechanical deformation in the entire life cycle of a material, it is important to accurately predict for guiding the structural designation and operation condition. Currently, most of the literature discusses the PFSA viscosity based on large-strain-rate experiments. Microscopic driving mechanisms and macroscopic responses to small strain rates that occur during PEMFC operation remain largely unclear. In this study, the characterises of PFSA viscosity were investigated in terms of molecular interactions and macroscopic rheological behaviour. A cross-scale model was developed to describe the shear thinning phenomenon to obtain a zero-shear viscosity, which captures the linear viscous behaviour for small strain rates. Subsequently, a modified generalised Maxwell model consisting of elastic-plastic elements and zero-shear viscosity-dependent viscous elements was proposed and calibrated by the tensile and stress relaxation experiments for Nafion 117 membranes. In addition, the proposed visco-elastoplastic model, after validated by small-strain rate experiments, was used to investigate the response to cyclic loading during start-up and shutdown, which provides insights on the mechanical damage due to the hydrothermal cycles.

Influence of Terbium Doping and Annealing on the Structural and Optical Characteristics of Sputtered Zinc Oxide Thin Films

This paper studied the structural and luminescent characteristics of undoped and doped-with-Tb3+-ions ZnO films of 200 nm and 600 nm thicknesses, grown via RF magnetron sputtering on (100) silicon substrate in Ar and Ar-O2 plasma. X-ray diffraction (XRD) patterns revealed a strong preferred orientation of ZnO and ZnO:Tb crystals of the wurtzite structure along the c-axis, perpendicular to the substrate. In the as-deposited ZnO:Tb films, the additional crystal phases, namely, Tb2O3, TbO2, and an amorphous phase, were revealed. The as-deposited undoped films were under tensile strain, that increased in the doped films. This proved the incorporation of the Tb3+ ions into the ZnO grains, and agreed with the Raman spectra investigation. The XRD data and atomic force microscopy study showed that Tb doping impeded the growth of grains and columns, respectively. The photoluminescence (PL) spectra of the doped films contained the UV band ascribed to exciton PL, a broad intrinsic defect-related band, and the narrow bands caused by the intra-shell transitions of the Tb3+ ions. Terbium doping suppressed ZnO emissions. The post-deposition rapid thermal annealing at up to 800 °C of both the undoped and doped films promoted tensile strain relaxation, grain growth, improvement in the ZnO crystal structure, and an increase in the exciton PL. The intensity of the Tb3+ PL changed non-monotonically, and was the highest for the film annealed at 600 °C. The conventional thermal annealing promoted the non-monotonic changes in the strains and grain sizes in such a way that, after annealing at 900 °C, their values became the same as in the as-deposited ZnO:Tb film. This structural change was accompanied by a decrease in the exciton and Tb3+ PL intensity. The formation of the Zn2SiO4 phase was observed via XRD, and confirmed via scanning electron microscopy. It was attributed to the interdiffusion through the film/substrate interface. The deposition in the Ar-O2 atmosphere is found to be more preferable for the formation of Tb3+ emission centers in the ZnO matrix.

Development of a tensile relaxation modulus test for identifying the tensile relaxation spectrum of asphalt binder

The tensile properties of asphalt binder such as strength, ductility, and stress-relaxation (relaxation) modulus are not only closely related to binder performance, but the modulus is also a necessary input for accurate material characterisation, modelling, and simulation. The linear behaviour of a homogeneous isotropic material can be fully characterised by both the tensile and shear relaxation moduli or their corresponding relaxation spectra. The shear properties of asphalt binders are often studied through dynamic shear tests. However, its tensile relaxation modulus and spectrum are seldom determined. Instead, they are often derived from the shear relaxation modulus with a prescribed Poisson ratio. However, it remains a question whether the ratio is material-, time- or even loading-independent. A tensile relaxation test is thus developed for determining the tensile relaxation modulus and spectrum directly. The continuous tensile relaxation spectrum is numerically derived based on the integral equation that connects the modulus to the spectrum. Spectrum regularisation and L-curve are used for solving the overfitting issue of the ill-posed equations. Two binders are used to evaluate the experimental method and the computational approach. The data suggest that the Poisson ratio may not be regarded as a constant for different asphalt binders. Hence, it is necessary to characterise asphalt binders using the tensile relaxation spectrum. Cross-checking between tensile and shear test data and between experimental relaxation moduli and the back-calculated ones from the tensile relaxation spectra indicate that the developed methods are robust and reliable.

General features of multi-parameter anomalies of six moderate earthquakes occurred near Zhangbei-Bohai fault in China during the past decades

The great Zhangbei-Bohai fault (ZBF) is an important seismic active zone in Northeastern China, which intersects with another great fault, namely Tancheng-Lujiang fault (TLF), in the Central Bohai Sea. Most of the previous studies only investigated the earthquakes (EQs) happened in the west section of ZBF and anomalies appeared in the land area, but few researchers focused on the EQs happened in the east section of ZBF and studied the anomalies appeared above the Bohai Sea. Recently, we have investigated the disturbances on and above the Bohai Sea associated with the Zhangbei Mb5.6 EQ in 1998, whose epicenter located in the west section of ZBF, and found that there was seismicity induced gas release from submarine TLF. To study further the multi-parameter anomalies of EQs near ZBF during past decades and their relationship with ZBF and TLF, a scrutiny strategy for seismic anomaly in the sea area was proposed in this study. After comprehensive screening of EQs occurred near ZBF from 1998 to 2022 using multi-source remote sensing data, potential seismic anomalies including the anomalies of microwave brightness temperature and sea surface roughness on Bohai Sea were found correlated with 6 of the 23 investigated EQs, and there were commonly anomalies of CO and CH4 concentration in the atmosphere. All these seismic anomalies were found developing mainly along the TLF in Bohai Sea, and started usually before shocking, appeared co-seismically and in the next few days. Regional inconsistencies among the distribution of CO and CH4 anomalies could be owning to the specific underwater reservoir in the Bohai Bay Basin. Though analyzing the focal mechanism solutions of the selected EQ cases, we found that the seismic anomaly existed only when the TLF was in a stress state of tensile relaxation.

Lattice Strain Relaxation and Compositional Control in As-Rich GaAsP/(100)GaAs Heterostructures Grown by MOVPE.

The fabrication of high-efficiency GaAsP-based solar cells on GaAs wafers requires addressing structural issues arising from the materials lattice mismatch. We report on tensile strain relaxation and composition control of MOVPE-grown As-rich GaAs1-xPx/(100)GaAs heterostructures studied by double-crystal X-ray diffraction and field emission scanning electron microscopy. Thin (80-150 nm) GaAs1-xPx epilayers appear partially relaxed (within 1-12% of the initial misfit) through a network of misfit dislocations along the sample [011] and [011-] in plane directions. Values of the residual lattice strain as a function of epilayer thickness were compared with predictions from the equilibrium (Matthews-Blakeslee) and energy balance models. It is shown that the epilayers relax at a slower rate than expected based on the equilibrium model, an effect ascribed to the existence of an energy barrier to the nucleation of new dislocations. The study of GaAs1-xPx composition as a function of the V-group precursors ratio in the vapor during growth allowed for the determination of the As/P anion segregation coefficient. The latter agrees with values reported in the literature for P-rich alloys grown using the same precursor combination. P-incorporation into nearly pseudomorphic heterostructures turns out to be kinetically activated, with an activation energy EA = 1.41 ± 0.04 eV over the entire alloy compositional range.

Effect of neutral polymeric bonding agent on tensile mechanical properties and damage evolution of NEPE propellant

Introducing Neutral Polymeric bonding agents (NPBA) into the Nitrate Ester Plasticized Polyether (NEPE) propellant could improve the adhesion between filler/matrix interface, thereby contributing to the development of new generations of the NEPE propellant with better mechanical properties. Therefore, understanding the effects of NPBA on the deformation and damage evolution of the NEPE propellant is fundamental to material design and applications. This paper studies the uniaxial tensile and stress relaxation responses of the NEPE propellant with different amounts of NPBA. The damage evolution in terms of interface debonding is further investigated using a cohesive-zone model (CZM). Experimental results show that the initial modulus and strength of the NEPE propellant increase with the increasing amount of NPBA while the elongation decreases. Meanwhile, the relaxation rate slows down and a higher long-term equilibrium modulus is reached. Experimental and numerical analyses indicate that interface debonding and crack propagation along filler–matrix interface are the dominant damage mechanism for the samples with a low amount of NPBA, while damage localization and crack advancement through the matrix are predominant for the ones with a high amount of NPBA. Finally, crosslinking density tests and simulation results also show that the effect of the bonding agent is interfacial rather than due to the overall crosslinking density change of the binder.

Comparison of mechanical properties of 3-dimensional printed and thermoformed orthodontic aligners

Orthodontic treatment using clear aligners has experienced exponential growth since its introduction in the late 1990s. Three-dimensional (3D) printing has also grown in popularity among orthodontists, and companies have begun to produce resins to directly print clear aligners. This study aimed to examine the mechanical properties of commercially available thermoformed aligners and direct 3D-printed aligners under laboratory conditions and a simulated oral environment. Samples were prepared (approximately 2.5 × 20 mm) from 2 thermoformed materials, EX30 and LD30 (Align Technology Inc, San Jose, Calif), as well as 2 direct 3D-printing resins, Material X (Envisiontec, Inc; Dearborn, Mich) and OD-Clear TF (3DResyns, Barcelona, Spain). Wet samples were subjected to phosphate-buffered saline at 37°C for 7 days, whereas dry samples were stored at 25°C. Tensile and stress relaxation tests were carried out on an RSA3 Dynamic Mechanical Analyzer (Texas Instruments, Dallas, Tex) and Instron Universal Testing System (Instron, Norwood, Mass) to calculate elastic modulus, ultimate tensile strength, and stress relaxation. The elastic modulus of dry and wet samples was 103.2 ± 17.3 MPa and 114.4 ± 17.9 MPa (EX30), 61.3 ± 9.18 MPa and 103.5 ± 11.4 MPa (LD30), 431.2 ± 16.0 MPa and 139.9 ± 34.6 MPa (Material X), and 38.4 ± 14.7 MPa and 38.3 ± 8.4 MPa (OD-Clear TF), respectively. The ultimate tensile strength of dry and wet samples was 64.41 ± 7.25 MPa and 61.43 ± 7.41MPa (EX30), 40.04 ± 5.00 MPa and 30.09 ± 1.50 MPa (LD30), 28.11 ± 3.75 MPa and 27.57 ± 4.09 MPa (Material X), and 9.34 ± 1.96 MPa and 8.27 ± 0.93 MPa (OD-Clear TF), respectively. Residual stress of wet samples at 2% strain for 2 hours was 59.99 ± 3.02% (EX30), 52.57 ± 12.28% (LD30), 6.98 ± 2.64% (Material X), and 4.39 ± 0.84% (OD-Clear TF). There was a significant difference in elastic modulus, ultimate tensile strength, and stress relaxation among the samples tested. Moisture, specifically a simulated oral environment, appears to have a greater effect on the mechanical properties of direct 3D-printed aligners when compared with thermoformed aligners. This is likely to impact the ability of 3D-printed aligners to generate and maintain adequate force levels for tooth movement.

Analysis of Low-Temperature Rheological and Mechanical Properties of Steel Slag Asphalt Mixture Based on Direct Tensile Test

Due to the high resource requirements for specimen preparation and testing equipment, the direct tensile test method is seldom used to study the cracking behavior of asphalt mixture at low temperatures. In this study, three asphalt mixtures were prepared in which all of the basalt or part of the basalt and basalt aggregate was replaced by steel slag. Through the direct tensile creep test and direct tensile relaxation tests including the measurement of creep rate, cumulative strain change rate, and relaxation time, the variation law of rheological properties of low-temperature steel slag asphalt mixture was analyzed and the variation law of viscoelastic properties was explored. Meanwhile, based on the traditional viscoelastic constitutive model, the creep compliance and relaxation modulus were fitted. The mechanical response of the transformation from creep compliance to relaxation modulus of steel slag asphalt mixture was analyzed by a numerical method. The results show that, with the decrease of temperature, the creep rate εs and cumulative strain change rate of the three asphalt mixtures gradually decline, and the relaxation time gradually increases. In particular, when the temperature was reduced from −20°C to −30°C, the cumulative strain change rate of all three asphalt mixtures reached the minimum, which was less than 10%. Moreover, none of them relax to 75% σ0 within 3,600 s at −30°C. The mixture specimens with steel slag replacing all basalt exhibited the best low-temperature deformation adaptation performance under different temperature conditions. Mixture specimens with basalt as aggregate have the worst low-temperature deformation adaptation performance. The relaxation modulus obtained by the measurement of creep compliance is similar to that obtained by testing, and the relaxation modulus calculated through the direct tensile test is more accurate.