System For Analysis At The Liquid Vacuum Interface Research Articles

Investigation of pyruvic acid photolysis at the air-liquid interface as a source of aqueous secondary organic aerosols

Pyruvic acid (PA) is a ubiquitous 2-oxocarboxylic acid in the atmosphere. Its photochemical process at the air-liquid (a-l) interface has been suggested as an important source of aqueous secondary organic aerosols. We investigated the photochemical reaction pathways of PA at the a-l interface using synchrotron-based vacuum ultraviolet single-photon ionization mass spectrometry (VUV SPI-MS) coupled with the System for Analysis at the Liquid Vacuum Interface (SALVI) microreactor. Results from mass spectral analysis and the determination of appearance energies (AEs) indicate that photolysis of PA can generate radicals, then they recombine with carboxylic acids and simple molecular oligomers. Furthermore, the preliminary products could form larger oligomers via radical reaction or esterification in the presence of hydroxyl and carboxyl functional groups. Mass spectral comparison shows that most photochemical reactions would complete within 4 h. The expanded photochemistry-driven reaction flowchart of PA is proposed based on the newly discovered products. Our results reveal that the interfacial PA photochemical reactions have different mechanisms from the bulk liquid due to the interfacial properties, such as molecular density, composition, and ion concentration. Our findings show that in situ mass spectral analysis with bright photon ionization is useful to elucidate the contribution of a-l interfacial reactions leading to aqSOA formation.

Microscale Electrochemical Corrosion of Uranium Oxide Particles.

Understanding the corrosion of spent nuclear fuel is important for the development of long-term storage solutions. However, the risk of radiation contamination presents challenges for experimental analysis. Adapted from the system for analysis at the liquid-vacuum interface (SALVI), we developed a miniaturized uranium oxide (UO2)-attached working electrode (WE) to reduce contamination risk. To protect UO2 particles in a miniatured electrochemical cell, a thin layer of Nafion was formed on the surface. Atomic force microscopy (AFM) shows a dense layer of UO2 particles and indicates their participation in electrochemical reactions. Particles remain intact on the electrode surface with slight redistribution. X-ray photoelectron spectroscopy (XPS) reveals a difference in the distribution of U(IV), U(V), and U(VI) between pristine and corroded UO2 electrodes. The presence of U(V)/U(VI) on the corroded electrode surface demonstrates that electrochemically driven UO2 oxidation can be studied using these cells. Our observations of U(V) in the micro-electrode due to the selective semi-permeability of Nafion suggest that interfacial water plays a key role, potentially simulating a water-lean scenario in fuel storage conditions. This novel approach offers analytical reproducibility, design flexibility, a small footprint, and a low irradiation dose, while separating the α-effect. This approach provides a valuable microscale electrochemical platform for spent fuel corrosion studies with minimal radiological materials and the potential for diverse configurations.

Studying Interfacial Dark Reactions of Glyoxal and Hydrogen Peroxide Using Vacuum Ultraviolet Single Photon Ionization Mass Spectrometry

Aqueous secondary organic aerosol (aqSOA) formation from volatile and semivolatile organic compounds at the air–liquid interface is considered as an important source of fine particles in the atmosphere. However, due to the lack of in situ detecting techniques, the detailed interfacial reaction mechanism and dynamics still remain uncertain. In this study, synchrotron-based vacuum ultraviolet single-photon ionization mass spectrometry (VUV SPI-MS) was coupled with the System for Analysis at the Liquid Vacuum Interface (SALVI) to investigate glyoxal dark oxidation products at the aqueous surface. Mass spectral analysis and determination of appearance energies (AEs) suggest that the main products of glyoxal dark interfacial aging are carboxylic acid related oligomers. Furthermore, the VUV SPI-MS results were compared and validated against those of in situ liquid time-of-flight secondary ion mass spectrometry (ToF-SIMS). The reaction mechanisms of the dark glyoxal interfacial oxidation, obtained using two different approaches, indicate that differences in ionization and instrument operation principles could contribute to their abilities to detect different oligomers. Therefore, the mechanistic differences revealed between the VUV SPI-MS and ToF-SIMS indicate that more in situ and real-time techniques are needed to investigate the contribution of the air–liquid interfacial reactions leading to aqSOA formation.

In situ, in vivo, and in operando imaging and spectroscopy of liquids using microfluidics in vacuum

This review offers a succinct overview of the development of a vacuum-compatible microfluidic reactor system for analysis at the liquid vacuum interface (SALVI), and its diverse applications in in situ, in vivo, and in operando imaging of liquid surfaces as well as the air-liquid (a-l), liquid-liquid (l-l), and solid-liquid (s-l) interfaces in the past decade. SALVI is one of the first microfluidics-based reactors that has enabled direct analysis of volatile liquids in vacuum surface tools such as scanning electron microscopy (SEM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Its integration into ambient and vacuum spectroscopy and microscopy is illustrated. Several applications are highlighted including (1) imaging nanoparticles in liquid using in situ SEM; (2) mapping the evolving l-l interface using in situ x-ray absorption spectroscopy and ToF-SIMS; (3) following complex a-l interfacial oxidation reaction products using in situ ToF-SIMS; (4) capturing biological interfaces of cells and microbes via in vivo multimodal and correlative imaging; and (5) monitoring the dynamic solid electrode and liquid electrolyte interface using in operando molecular imaging. Finally, outlook and recommendations are presented. Besides showing the holistic information volume obtained by real-time multiplexed imaging, this review intends to convey the importance of tool development in revolutionizing surface and interface analysis using vacuum platforms previously limited to solid surfaces. Microfluidics is manifested to be not limited to ambient conditions in many examples in this review. Moreover, fundamental interfacial phenomena underpinning mass and charge transfer can now be pursued in real time via innovated chemical imaging and spectroscopy.

Revealing the Structural Evolution of Green Rust Synthesized in Ionic Liquids by In Situ Molecular Imaging

AbstractIonic liquids are green solvents that have wide applications in material synthesis, catalysis, and separation. A model switchable ionic liquid (SWIL) consisting of 1,8‐diazabicycloundec‐7‐ene (DBU) and 1‐hexanol with carbon dioxide (CO2) as the trigger gas is chosen to synthesize nanocrystalline green rust. Under anoxic conditions, by adding iron (II) acetate (Fe(C2H3O2)2) and methanol to the degassed SWIL, a nanoparticulate green rust with carbonate (nano‐GR) is synthesized. More importantly, the molecular structural change of the ionic liquid resulting in green rust crystallines is first characterized using in situ liquid using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) coupled with the system for analysis at the liquid vacuum interface (SALVI), a vacuum compatible microfluidic reactor in this work. Dimers and ionic clusters consisting ferric and ferrous ions are identified in liquid ToF‐SIMS spectra. Spectral principal component analysis is used to confirm that these ion pairs including dimers and cluster ions are different from nonionic liquids. The results show that liquid ToF‐SIMS can be a useful tool to study complex liquids at the molecular level providing insights into predicative synthesis of nanomaterials using environmentally friendly green solvents and giving unique visualization of the evolving material interface due to nucleation.

Understanding Time Dependence on Zinc Metal-Organic Framework Growth Using in Situ Liquid Secondary Ion Mass Spectrometry.

The abundance of novel metal-organic framework (MOF) materials continues to increase as more applications are discovered for these highly porous, well-ordered crystalline structures. The simplicity of constituents allows for the design of new MOFs with virtue of functionality and pore topology toward target adsorbates. However, the fundamental understanding of how these frameworks evolve during nucleation and growth is mostly limited to speculation from simulation studies. In this effort, we utilize a unique vacuum compatible system for analysis at the liquid vacuum interface (SALVI) microfluidic interface to analyze the formation and evolution of the benchmark MOF-74 framework using time-of-flight secondary ion mass spectrometry (ToF-SIMS). Principal component analysis of the SIMS mass spectra, together with ex situ electron microscopy, powder X-ray diffractometry, and porosimetry, provides new insights into the structural growth, metal-oxide cluster formation, and aging process of Zn-MOF-74. Samples collected over a range of synthesis times and analyzed closely with in situ ToF-SIMS, transmission electron microscopy, and gas adsorption studies verify the developing pore structure during the aging process.

Evolution of aqSOA from the Air-Liquid Interfacial Photochemistry of Glyoxal and Hydroxyl Radicals.

The effect of photochemical reaction time on glyoxal and hydrogen peroxide at the air-liquid (a-l) interface is investigated using in situ time-of-flight secondary ion mass spectrometry (ToF-SIMS) enabled by a system for analysis at the liquid vacuum interface (SALVI) microreactor. Carboxylic acids are formed mainly by reaction with hydroxyl radicals in the initial reactions. Oligomers, cluster ions, and water clusters formed due to longer photochemistry. Our results provide direct molecular evidence that water clusters are associated with proton transfer and the formation of oligomers and cluster ions at the a-l interface. The oligomer formation is facilitated by water cluster and cluster ion formation over time. Formation of higher m/z oligomers and cluster ions indicates the possibility of highly oxygenated organic components formation at the a-l interface. Furthermore, new chemical reaction pathways, such as surface organic cluster, hydration shell, and water cluster formation, are proposed based on SIMS spectral observations, and the existing understanding of glyoxal photochemistry is expanded. Our in situ findings verify that the a-l interfacial reactions are important pathways for aqueous secondary organic aerosol (aqSOA) formation.

Enabling liquid vapor analysis using synchrotron VUV single photon ionization mass spectrometry with a microfluidic interface.

Vacuum ultraviolet (VUV) single photon ionization mass spectrometry (SPI-MS) is a vacuum-based technique typically used for the analysis of gas phase and solid samples, but not for liquids due to the challenge in introducing volatile liquids in a vacuum. Here we present the first demonstration of in situ liquid analysis by integrating the System for Analysis at the Liquid Vacuum Interface (SALVI) microfluidic reactor into VUV SPI-MS. Four representative volatile organic compound (VOC) solutions were used to illustrate the feasibility of liquid analysis. Our results show the accurate mass identification of the VOC molecules and the reliable determination of appearance energy that is consistent with ionization energy for gaseous species in the literature as reported. This work validates that the vacuum-compatible SALVI microfluidic interface can be utilized at the synchrotron beamline and enable the in situ study of gas-phase molecules evaporating off the surface of a liquid, which holds importance in the study of condensed matter chemistry.

<em>In Situ</em> Characterization of Boehmite Particles in Water Using Liquid SEM

In situ imaging and elemental analysis of boehmite (AlOOH) particles in water is realized using the System for Analysis at the Liquid Vacuum Interface (SALVI) and Scanning Electron Microscopy (SEM). This paper describes the method and key steps in integrating the vacuum compatible SAVLI to SEM and obtaining secondary electron (SE) images of particles in liquid in high vacuum. Energy dispersive x-ray spectroscopy (EDX) is used to obtain elemental analysis of particles in liquid and control samples including deionized (DI) water only and an empty channel as well. Synthesized boehmite (AlOOH) particles suspended in liquid are used as a model in the liquid SEM illustration. The results demonstrate that the particles can be imaged in the SE mode with good resolution (i.e., 400 nm). The AlOOH EDX spectrum shows significant signal from the aluminum (Al) when compared with the DI water and the empty channel control. In situ liquid SEM is a powerful technique to study particles in liquid with many exciting applications. This procedure aims to provide technical know-how in order to conduct liquid SEM imaging and EDX analysis using SALVI and to reduce potential pitfalls when using this approach.

In Situ Characterization of Shewanella oneidensis MR1 Biofilms by SALVI and ToF-SIMS.

Bacterial biofilms are surface-associated communities that are vastly studied to understand their self-produced extracellular polymeric substances (EPS) and their roles in environmental microbiology. This study outlines a method to cultivate biofilm attachment to the System for Analysis at the Liquid Vacuum Interface (SALVI) and achieve in situ chemical mapping of a living biofilm by time-of-flight secondary ion mass spectrometry (ToF-SIMS). This is done through the culturing of bacteria both outside and within the SALVI channel with our specialized setup, as well as through optical imaging techniques to detect the biofilm presence and thickness before ToF-SIMS analysis. Our results show the characteristic peaks of the Shewanella biofilm in its natural hydrated state, highlighting upon its localized water cluster environment, as well as EPS fragments, which are drastically different from the same biofilm's dehydrated state. These results demonstrate the breakthrough capability of SALVI that allows for in situ biofilm imaging with a vacuum-based chemical imaging instrument.

In situ nuclear magnetic resonance microimaging of live biofilms in a microchannel.

Biofilms are comprised of microbial cells and an extracellular polymeric substance (EPS) matrix that supports interactions between community members and with the local environment. The highly hydrated EPS matrix makes the application of many biofilm visualization techniques difficult. Hence, to better visualize how biofilms interact with their environment, there is a need for imaging techniques to monitor hydrated state biofilm dynamics. We employed an in situ dynamic approach to construct label-free images of biofilms. In situ imaging was conducted using a vacuum compatible microfluidic reactor, SALVI (System for Analysis at the Liquid Vacuum Interface), for biofilm growth; real-time confocal laser scanning microscopy analysis; and nuclear magnetic resonance (NMR) microimaging and spectroscopy. We integrated SALVI microchannel fluids and live biofilms to demonstrate in situ measurement capabilities, including velocity mapping, diffusion coefficient mapping, relaxometry, localized spectroscopy, relaxation times, porosity, and two- and three-dimensional imaging within the microchannel at high spatial resolution. We monitored organic acids adjacent to biofilms, suggesting that kinetic rate and substrate-product yield ratio studies are possible using the SALVI microfluidic reactor for growth characterizations. The integration of NMR microimaging studies into the SALVI platform demonstrates that a multimodal microfluidic platform can serve as an avenue to explore complex biological phenomena, such as biofilm attachment to surfaces, with detailed quantitative physical and chemical mapping. The further incorporation of other SALVI-compatible technologies, such as liquid time-of-flight secondary ion mass spectrometry imaging, with NMR microimaging will produce a powerful correlative approach to monitor in situ biofilm chemistry and dynamics at different spatial scales.

Improving the Molecular Ion Signal Intensity for In Situ Liquid SIMS Analysis.

In situ liquid secondary ion mass spectrometry (SIMS) enabled by system for analysis at the liquid vacuum interface (SALVI) has proven to be a promising new tool to provide molecular information at solid-liquid and liquid-vacuum interfaces. However, the initial data showed that useful signals in positive ion spectra are too weak to be meaningful in most cases. In addition, it is difficult to obtain strong negative molecular ion signals when m/z>200. These two drawbacks have been the biggest obstacle towards practical use of this new analytical approach. In this study, we report that strong and reliable positive and negative molecular signals are achievable after optimizing the SIMS experimental conditions. Four model systems, including a 1,8-diazabicycloundec-7-ene (DBU)-base switchable ionic liquid, a live Shewanella oneidensis biofilm, a hydrated mammalian epithelia cell, and an electrolyte popularly used in Li ion batteries were studied. A signal enhancement of about two orders of magnitude was obtained in comparison with non-optimized conditions. Therefore, molecular ion signal intensity has become very acceptable for use of in situ liquid SIMS to study solid-liquid and liquid-vacuum interfaces. Graphical Abstract ᅟ.

Switchable 1,8-diazabicycloundec-7-ene and 1-hexanol ionic liquid analyzed by liquid ToF-SIMS

Switchable ionic liquids (SWIL) play an important role in green chemistry. Due to the nature of SWIL chemistry, such as air sensitivity, pressure, and temperature dependence, it is difficult to characterize SWIL using vacuum-based surface techniques. The fully CO2 loaded 1:1 mixtures of 1,8-diazabicycloundec-7-ene (DBU) and 1-hexanol (a SWIL system) and non-CO2 loaded DBU and 1-hexanol mixture were analyzed by in situ time-of-flight secondary ion mass spectrometry (ToF-SIMS) coupled with the system for analysis at the liquid vacuum interface (SALVI), respectively. The DBU/1-hexanol/CO2 SWIL was injected into the microchannel before liquidsecondary ion mass spectrometryanalysis. Bi3+ primary ion beam was used. The positive and negative spectra of the SWIL chemical components are presented. The characteristic peaks m/z 153 (protonated DBU) in the positive mode and m/z 101 (deprotonated 1-hexanol) in the negative mode were observed. In addition, ion pair peaks including m/z 253, 319, 305, and 451 in the positive mode and m/z 145, 223, and 257 in the negative mode are first observed using this approach. These results demonstrate that the SALVI microfluidic reactor enables the vacuum-based surface technique (i.e., ToF-SIMS) for in situ characterization of challenging liquid samples such as ionic liquids.

In Situ Characterization of Hydrated Proteins in Water by SALVI and ToF-SIMS.

This work demonstrates in situ characterization of protein biomolecules in the aqueous solution using the System for Analysis at the Liquid Vacuum Interface (SALVI) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The fibronectin protein film was immobilized on the silicon nitride (SiN) membrane that forms the SALVI detection area. During ToF-SIMS analysis, three modes of analysis were conducted including high spatial resolution mass spectrometry, two-dimensional (2D) imaging, and depth profiling. Mass spectra were acquired in both positive and negative modes. Deionized water was also analyzed as a reference sample. Our results show that the fibronectin film in water has more distinct and stronger water cluster peaks compared to water alone. Characteristic peaks of amino acid fragments are also observable in the hydrated protein ToF-SIMS spectra. These results illustrate that protein molecule adsorption on a surface can be studied dynamically using SALVI and ToF-SIMS in the liquid environment for the first time.

Two-dimensional and three-dimensional dynamic imaging of live biofilms in a microchannel by time-of-flight secondary ion mass spectrometry.

A vacuum compatible microfluidic reactor, SALVI (System for Analysis at the Liquid Vacuum Interface), was employed for in situ chemical imaging of live biofilms using time-of-flight secondary ion mass spectrometry (ToF-SIMS). Depth profiling by sputtering materials in sequential layers resulted in live biofilm spatial chemical mapping. Two-dimensional (2D) images were reconstructed to report the first three-dimensional images of hydrated biofilm elucidating spatial and chemical heterogeneity. 2D image principal component analysis was conducted among biofilms at different locations in the microchannel. Our approach directly visualized spatial and chemical heterogeneity within the living biofilm by dynamic liquid ToF-SIMS.