Synthetic Humeri Research Articles

Biomechanical Analysis of Different K-wire Configurations for Percutaneous Fixation of Two-Part Proximal Humerus Fractures.

The increasing prevalence of proximal humerus fractures in the elderly population, particularly osteoporotic fractures, necessitates a biomechanical evaluation of Kirschner wire (K-wire) configurations used in percutaneous fixation. This study investigates the stability of different K-wire configurations and examines the effect of wire size and type (smooth vs. threaded). Using 27 synthetic humeri models, we compare three configurations as follows: four parallel ascending K-wires (box-type), two ascending and two descending K-wires, and a combination of both. Results show that adding descending K-wires significantly enhances stability, particularly against torsional forces. This study highlights the importance of wire type and configuration in stabilizing proximal humerus fractures. Multiplanar constructs with descending K-wires, especially threaded ones, offer better stability. These insights help improve surgical techniques for elderly and osteoporotic patients, but further research using cadaver models is needed for clinical validation.

Impact of augmentation strategy variations on the mechanical characteristics of patients with osteoporotic proximal humerus fractures with medial column instability.

Low bone density and lack of medial support are the two most important factors affecting the stability of locking plate fixation for osteoporotic proximal humeral fractures (PHFs). This study aimed to compare the biomechanical characteristics of PHILOS locking plates combined with calcar screws, bone cement, fibular allografts, and medial locking plate support strategies for treating osteoporotic PHFs with medial column instability. A three-part osteoporotic PHF (AO 11-B3.2) model with metaphyseal loss was generated using 40 synthetic humeri and fixed via four distinct medial support strategies. All models were mechanically tested to quantify the mechanical characteristics. Subsequently, finite element models were created for each biomechanical test case. The stress distribution and displacement of the four different fixation structures were analyzed using finite element analysis. The results demonstrated that the PHILOS locking plate combined with the medial locking plate, exhibited the greatest stability when subjected to axial, shear, and torsional loading. Furthermore, the PHILOS locking plate combined with bone cement showed structural stability similar to that of the PHILOS locking plate combined with fibular allograft but with lower stress levels on the fracture surface. In conclusion, the PLP-MLP fixation structure showed superior biomechanical properties under axial, shear, and torsional loading compared to other medial support methods. Repairing the medial support when treating osteoporotic PHFs with medial column instability can enhance the mechanical stability of the fracture end in both the short and long term.

A new configuration of lateral-pin fixation for pediatric supracondylar humeral fracture: A biomechanical analysis.

The aim of this study was to biomechanically compare a new lateral-pinning technique, in which pins engage the medial and lateral columns of the distal humerus in a divergent configuration in both the axial and sagittal planes instead of the coronal plane, with the cross-pin, and with 2 and 3 coronally divergent lateral-pin techniques in a synthetic humerus model of supracondylar humerus fractures. Thirty-six identical synthetic models of the humerus simulating a standardized supracondylar humerus fracture were included in this study. They were divided into 4 groups based on the pin configuration of fixation: the new 3-lateral pin-fixation technique (group A), 2 crossed pins (group B), 3 divergent lateral pins (group C), and 2 divergent lateral pins (group D). Each model was subjected to combined axial and torsional loading, and then torsional stability and torsional stiffness (Nmm/°) were recorded. Group A had greater rotational stability than groups C and D but had no statistically significant additional rotational stability compared with group B (P=.042, P=.008, P=.648, respectively), whereas group B had greater rotational stability than only group D (P=.020). Furthermore, group A demonstrated higher internal rotational stiffness compared with groups C and D (P=.038, P=.006, respectively). Group B had better internal rotational stiffness than group D (P=.015). There was no significant difference in internal rotational stiffness between groups A and B (P=. 542), groups B and C (P=.804), and groups D and C (P=.352). Although no statistically significant differences existed between groups A and B, the modified pin configuration exhibited the highest torsional stability and stiffness. Group D showed the lowest values in all biomechanical properties. This study has shown us that this new lateral-pinning technique may provide torsional resistance to internal rotational displacement as strong as the standard technique of crossed-pin configuration of fixation. Furthermore, with this new pin configuration, greater torsional resistance can be obtained than with either the standard 2- or the standard 3-lateral divergent pin configuration. Cite this article as: Bilgili F, Demirel M, Birişik F, Balcı Hİ, Sunbuloglu E, Bozdag E. A new configuration of lateral-pin fixation for pediatric supracondylar humeral fracture: A biomechanical analysis. Acta Orthop Traumatol Turc., 2023 10.5152/j.aott.2024.21091 [Epub Ahead of Print].

Biomechanical Analysis of Combined Medial Calcar and Lateral Locked Plating Versus Isolated Lateral Locked Plating of Proximal Humerus Fractures.

Medial calcar buttress plating combined with lateral locked plating is biomechanically tested against isolated lateral locked plating in synthetic humeri models for the treatment of proximal humerus fractures. Proximal humerus fractures (OTA/AO type 11-A2.1) were manufactured in 10 pairs of Sawbones humeri models (Sawbones, Pacific Research Laboratories, Vashon Island, WA). Specimen were randomly assigned and instrumented with either medial calcar buttress plating combined with lateral locked plating (CP) or isolated lateral locked plating (LP). Nondestructive torsional and axial load tests were performed to evaluate construct stiffness. Large-cycle axial tests were conducted followed by destructive ramp-to-failure tests. Cyclic stiffness was compared in both nondestructive and ultimate failure loads. Failure displacement was recorded and compared between groups. The addition of medial calcar buttress plating to lateral locked plating constructs significantly increased the axial ( P < 0.01) and torsional ( P < 0.01) stiffness of the construct compared with isolated lateral locked plating by 95.56% and 37.46%, respectively. All models demonstrated greater axial stiffness ( P < 0.01) after 5000 cycles of axial compression, not dependent on the fixation method. During destructive testing, the CP construct withstood 45.35% larger load ( P < 0.01) and congruently exhibited 58% less humeral head displacement ( P = 0.02) before failure when compared with the LP construct. This study demonstrates the biomechanical superiority of medial calcar buttress plating when combined with lateral locked plating as compared with isolated lateral locked plating of OTA/AO type 11-A2.1 proximal humerus in synthetic humeri models.

The effect of shoulder prosthesis stem length on failure due to torsional loading. A biomechanical study in composite humeri

Shoulder arthroplasty is becoming increasingly common. With evolving implant designs, multiple humeral stem options exist for the surgeon to choose from. New stemless and short-stem systems are modular, remove less native bone stock, and better adapt to patient anatomy. It has been suggested that shorter stem implants may be protective against periprosthetic fracture; however, this has not been mechanistically evaluated. Therefore, this study aimed to biomechanically test synthetic humeri with long-stem, short-stem, and stemless arthroplasty components in a torsional manner to evaluate their response to loading and characterize failure. Twenty-four synthetic humeri were implanted with long stem, short stem, or stemless uncemented prosthesis, 8 in each group. Humeri were mounted in a custom testing jig with a morse taper interfacing with a mechanical testing system. After a 20N axial force, specimens were torsionally loaded to failure at 15 degrees/sec, with 50 Hz collection. Torque vs. rotation curves were generated for each specimen, and stiffness, yield, ultimate strength, and failure load were measured. ANOVA and post hoc pairwise comparisons were used to assess effect of stem type on mechanical test variable. The association of the stem type with fracture type was analyzed by a Fisher's Exact test. Statistical significance was set at P<.05. During torsional loading, long-stem implants were significantly stiffer than short or stemless implants. The angle of implant yielding was similar across stem designs; however, stemless implants had a lower yield torque. This correlated with a decreased yield energy in stemless compared to short stems as well. Maximum torque and failure torque was also significantly higher in short-stem and long-stem implants compared to stemless. Periprosthetic fractures in shoulder arthroplasty are a concern in low-energy trauma, and stem design likely plays a significant role in early implant-bone failure. Our results suggest stemless implants under torsional load fail at lower stress and are less stiff than stemmed implants. The failure mechanism of stemless implants through metaphyseal cancellous bone emphasizes the effect bone quality has on implant fixation. There is likely a balance of torsional stability to survive physiologic loads while minimizing diaphyseal stress and risk of diaphyseal periprosthetic fracture. This combined with revision and fixation options represent decisions the surgeon is faced with when performing shoulder arthroplasty.

Biomechanical analysis of a novel Y-plate designed for the treatment of extraarticular distal humerus fractures

Adult distal humerus fractures are infrequent, yet they account for one-third of all humerus fractures. For the treatment of comminuted and osteoporotic fractures, locking plates are claimed to be biomechanically superior to alternative internal fixing techniques. Treatment remains difficult despite recent advancements and the use of locking plates due to frequent comminution, low bone quality, and limited healing ability in osteoporotic bone. An optimal design of the newly constructed plate and the control model were selected. The biomechanical characteristics of non-osteoporotic and osteoporotic synthetic bone were compared on six models. The biomechanical properties of the new plate were tested and compared on 54 osteoporotic synthetic humerus models. The control models were reconstructive and parallel LCPs. The tests were carried out under static and dynamic axial, lateral and bending loads. Fracture displacements were measured by optical measuring system Aramis. The test model is significantly stiffer for lateral load (p = 0.0007) and for bending load at the moment of model failure (p = 0.0002), while for axial load the LCP model showed greater stiffness (p = 0.0017). During lateral dynamic loading, all three LCP models broke and there was a significant difference compared to the test model (p = 0.0125). The LCP model is dynamically significantly more durable under axial load, while the largest displacements were recorded with the test model (p = 0.029). The displacements induced by all three loads are within the limits that fulfil the parameters of appropriate biomechanical stability. A novel locking plate for extra-articular distal humerus fractures may provide an alternative to the traditional two-plate.

The addition of cerclage wiring does not improve proximal bicortical fixation of locking plates for Type C periprosthetic fractures in synthetic humeri

BackgroundTreatment of proximal humerus periprosthetic fractures is challenging. It remains difficult to achieve robust fixation of the proximal fragment to the locking plate using cerclage wiring and/or unicortical screws. Use of polyaxial tangentially directed bicortical locking screws increases screw purchase, but it is unclear if this option provides robust fixation. This biomechanical study compares fixation of constructs using cerclage wires, bicortical locking screws, and a hybrid method utilizing both methods. MethodsUncemented humeral stems were implanted into synthetic humeri and Type C periprosthetic fractures were simulated with a 1 cm transverse osteotomy. Distal ends of locking plates were secured with bicortical non-locking screws. The proximal ends were supported by either isolated cerclage wires, polyaxial locking screws, or a hybrid combination of both (n = 6 for each group). A universal test frame was used for non-destructive torsion and cyclic axial compression tests. 3-D motion tracking was employed to determine stiffnesses and relative interfragmentary motions. FindingsIsolated screw constructs showed significantly increased resistance against torsional movement, bending, and shear, (p < 0.05) in comparison to cerclage constructs. The hybrid construct provided no significant changes in stability over the isolated screw construct. InterpretationAddition of cerclage wires in this synthetic bone model of Type C periprosthetic humerus fractures did not add significant stability to proximal bicortical locking plate fixation. Considering risks of tissue stripping and nerve injury, usage of cerclage wires in a similar clinical setting should be chosen carefully, especially when bicortical fixation around the prosthetic stem can be achieved.

Biomechanical Analysis of Crossed Pinning Construct in Supracondylar Fracture of Humerus: Does the Point of Crossing Matter?

IntroductionThis appears to be the first biomechanical study that compares the stability of various locations of the crossing points in crossed pinning Kirschner wiring (K-wire) construct in treating pediatric supracondylar humerus fracture (SCHF). Additionally, this study compared the biomechanical stability between crossed pinning K-wire construct and the three-lateral divergent K-wire construct.MethodsFor the study purpose, 30 synthetic humerus bones were osteotomised at mid-olecranon fossa, anatomically reduced, and pinned using two 1.6-millimeter K-wires in five different constructs. A total of six samples were prepared for each construct and tested for extension, flexion, valgus, varus, internal rotation, and external rotation forces.ResultsAs for crossed pinning K-wire construct, the center crossing point emerged as the stiffest construct in both linear and rotational forces, in comparison to the lateral crossing point, superior crossing, and medial crossing pointConclusionBased on this analysis, it is highly recommended that, if the crossed pinning construct is selected to treat supracondylar humerus fracture, the surgeon should aim for center crossing point as it is the most stable construct. Nevertheless, if lateral and superior crossing points are obtained during the initial attempt of fixation, the fixation may be accepted without revising the K-wire as the stability of these two constructs are comparable and portrayed no significant difference when compared to that of the center crossing point. Additionally, it is essential to avoid the medial crossing point as it is significantly less stable in terms of rotational force when compared to the center crossing point.

Biomechanical Assessment of Three Osteosynthesis Constructs by Periprosthetic Humerus Fractures.

Background Biomechanical stability assessment of 3 different constructs for proximal fixation of a locking compression plate (LCP) in treating a Worland type C periprosthetic fracture after total shoulder arthroplasty. Methods 27 Worland type C fractures after shoulder arthroplasty in synthetic humeri were treated with 14-hole LCP that is proximally fixed using the following: (1) 1 × 1.5 mm cerclage wires and 2x unicortical-locking screws, (2) 3 × 1.5 mm cerclage wires, or (3) 2x bicortical-locking attachment plates. Torsional stiffness was assessed by applying an internal rotation moment of 5 Nm and then after unloading the specimen, an external rotation moment of 5 Nm at the same rate was applied. Axial stiffness was assessed by applying a 50 N preload, and then applying a cyclic load of 250 N, then increasing the load by 50 N each time, until a maximum axial load of 2500 N was reached or specimen failure occurred. Results With regard to internal as well as external rotational stiffness, group 1 showed a mean stiffness of 0.37 Nm/deg and 0.57 Nm/deg, respectively, group 2 had a mean stiffness of 0.51 Nm/deg and 0.39 Nm/deg, respectively, while group 3 had a mean stiffness of 1.34 Nm/deg and 1.31 Nm/deg, respectively. Concerning axial stiffness, group 1 showed an average stiffness of 451.0 N/mm, group 2 had a mean stiffness of 737.5 N/mm, whereas group 3 had a mean stiffness of 715.8 N/mm. Conclusion Group 3 displayed a significantly higher torsional stiffness while a comparable axial stiffness to group 2.

The effect of hole size on failure loads of the distal humerus fenestration in Outerbridge-Kashiwagi arthroplasty: A biomechanical study.

The aim of this study was to biomechanically assess the effect of humeral-fenestration size in the Outerbridge-Kashiwagi arthroplasty on the ultimate failure load of the distal humerus in a synthetic bone model. We biomechanically tested the influence of different humeral-fenestration sizes on the failure load of the distal humerus in Outerbridge-Kashiwagi arthroplasty. A total of 50 synthetic humerus models were divided into 5 groups based on the fenestration size: 10 mm, 12 mm, 15 mm, 18 mm, and 20 mm. All the samples were randomly assigned to receive either axial or anteroposterior (AP) loading and then loaded to failure at a rate of 2 mm/min on a material testing machine. The data regarding ultimate failure loads under the axial and AP loading were analyzed. Under the AP loading, the mean ultimate failure loads of the 18 mm and 20 mm groups were lower than those of the other groups. Under the axial loading, the mean ultimate failure load of the 10 mm group was significantly greater than that of the 15 mm, 18 mm, and 20 mm groups. Additionally, the ultimate failure load of the 20 mm group was significantly lower than that of the 12 mm, 15 mm, and 18 mm groups. The distal humeral fenestrations with a size greater than 18 mm may offer poor biomechanical properties in the Outerbridge-Kashiwagi ulnohumeral arthroplasty.

Biomechanical behavior of three types of fixation in the two-part proximal humerus fracture without medial cortical support.

BackgroundThe purpose of this study was to evaluate the role of a non-locking plate applied to the anteromedial surface of the proximal humerus on loads at the implant-bone interface of non-locking and locking lateral plate fixation of proximal humeral fractures with a medial gap.MethodsTwenty synthetic humeri models were used. In fifteen, the proximal portion of the humerus was osteotomized to create a two-part surgical neck fracture, with a 10-mm medial gap and a 5-mm lateral gap; five models were controls. In the osteotomized humeri, five models were stabilized with a locking lateral plate (group L), five with a locking lateral plate and an anteromedial non-locking plate (group L+T), and five with a non-locking lateral plate and a non-locking anteromedial plate (group T+T). All humeri were tested under axial loading until catastrophic failure, which was characterized as complete closure of the medial gap. Stiffness was calculated using force vs. displacement curves. The data were analyzed via descriptive and inferential studies, at a 5% significance level.ResultsStatistically significant differences were seen among all the constructions. The combination of a lateral locking plate with an anteromedial non-locking plate (group L+T) was the stiffest construction, while the combination of a non-locking lateral plate with a non-locking anteromedial plate (group T+T) was the least stiff, even in comparison with a single locking lateral plate (p = 0.01). When the two groups which utilized a lateral locking plate (groups L+T and L) were compared, the group with additional anteromedial support demonstrated greater stiffness (p = 0.03), and stiffness values for the control group comprised of intact humeri models were even higher (p = 0.01).ConclusionCombining a lateral locking plate with a non-locking anteromedial plate provides a stiffer construction for fixation of unstable two-part proximal humerus fractures with a medial gap. Mechanical benefits of medial support with a second non-locking antero-medial plate seems to be related with better construct stability in terms of strength and fatigue, potentially reducing the risk of varus collapse of the humerus head and fracture healing disturbances.

Biomechanical Analysis of Two Types of Humerus Supracondylar Fracture Fixation in Anatomical Model.

Objective To analyze the stability of humerus supracondylar fracture fixation with Kirschner wires comparing intramedullary and lateral (Fi), and two parallel lateral wires (FL) fixation in experimental models, to define which configuration presents greater stability. Methods A total of 72 synthetic humeri were cross-sectioned to simulate the fracture. These bones were divided into two equal groups and the fractures were fixed with parallel Kirschner wires (FL) and with a lateral and intramedullary (Fi) wire. Then, the test specimens were subjected to stress load tests on a universal test machine, measured in Newtons (N). Each group was subdivided into varus load, valgus, extension, flexion, external rotation and internal rotation. An analysis of the data was performed comparing the subgroups of the FL group with their respective subgroups of the Fi group through the two-tailed t test. Results The two-tailed t test showed that in 4 of the 6 evaluated conditions there was no significant statistical difference between the groups ( p > 0.05). We have found a significant difference between the group with extension load with a mean of 19 N (FL group) and of 28.7 N (Fi group) ( p = 0.004), and also between the groups with flexural load with the mean of the forces recorded in the FL group of 17.1 N and of 22.9 N in the Fi group ( p = 0.01). Conclusion Fixation with one intramedullary wire and one lateral wire, considering loads in extension and flexion, presents greater stability when compared to a fixation with two lateral wires, suggesting similar clinical results.

Biomechanical Analysis of Crossed Pinning Construct on Supracondylar Fracture of Humerus in Children: Does Point of Crossing Matters?

Introduction: Percutaneous pin fixation either by crossed pinning construct (CPC) or lateral divergent pinning construct (LDPC) are the recommended treatment for displaced supracondylar humerus fractures (SCHF) in children. Several studies had compared the biomechanical stability between these two, however, a biomechanical analysis of varying crossing point location in CPC has not been performed previously. The aim of this study was to compare the stability of various crossing point location in CPC and LDPC. Materials and Methods: Thirty synthetic humeri were osteotomized at mid olecranon fossa, anatomically reduced and pinned using two 1.6 mm Kirschner wiresin five different constructs namely centre point, medial point, lateral point, superior point and LDPC. Six samples were prepared for each construct and were tested for extension, flexion, valgus, varus, internal rotation and external rotation forces by using Universal Tensile Machine and the data were analysed with R Statistic. Results: The centre point CPC was the stiffest while the LDPC and medial point CPC were the least stiff construct for linear and rotational force respectively. Lateral point CPC, and superior point CPC showed no statistically significant difference when compared to centre point CPC. Conclusion: The centre point CPC was the most stable construct while the LDPC and medial point CPC were the least stable. The stability of lateral point CPC and superior point CPC were statistically comparable to centre point CPC. Clinically, this will help the treating surgeon to reduce the numbers of attempt during K-wire insertion in order to get perfect centre point CPC.

Biomechanical comparison of screw-based zoning of PHILOS and Fx proximal humerus plates

BackgroundTreatment of proximal humerus fractures with locking plates is associated with complications. We aimed to compare the biomechanical effects of removing screws and blade of a fixed angle locking plate and hybrid blade plate, on a two-part fracture model.MethodsForty-five synthetic humeri were divided into nine groups where four were implanted with a hybrid blade plate and the remaining with locking plate, to treat a two-part surgical neck fracture. Plates’ head screws and blades were divided into zones based on their distance from fracture site. Two groups acted as a control for each plate and the remaining seven had either a vacant zone or blade swapped with screws. For elastic cantilever bending, humeral head was fixed and the shaft was displaced 5 mm in extension, flexion, valgus and varus direction. Specimens were further loaded in varus direction to investigate their plastic behaviour.ResultsIn both plates, removal of inferomedial screws or blade led to a significantly larger drop in varus construct stiffness than other zones. In blade plate, insertion of screws in place of blade significantly increased the mean extension, flexion valgus and varus bending stiffness (24.458%/16.623%/19.493%/14.137%). In locking plate, removal of screw zones proximal to the inferomedial screws reduced extension and flexion bending stiffness by 26–33%.ConclusionsAlthough medial support improved varus stability, two inferomedial screws were more effective than blade. Proximal screws are important for extension and flexion. Mechanical consequences of screw removal should be considered when deciding the number and choice of screws and blade in clinic.

Biomechanical evaluation of a new technique for external fixation of unstable supracondylar humerus fractures in children.

Closed reduction and percutaneous pinning is regarded as the treatment of choice for unstable supracondylar humerus fractures, but there are cases in which the use of external fixation is preferable. The aim of this study was to investigate whether the method of external fixation could be considered as a stable alternative to percutaneous pinning and whether there was a difference in stability between two different external fixator constructs. Eighteen synthetic humeri were allocated to three groups of six bones each. The specimens of group 1 were fixed by crossed pinning, those of group 2 by a new variation of an external fixator and the specimens of group 3 by an established variation of it. Osteotomy displacement was measured under static loading in internal and external rotation, as well as in extension and flexion. The external fixators proved to be significantly more stable than crossed pinning in sagittal loading. In internal rotation loading the new variation of the external fixator showed the best results. In case of fractures that can't be replaced by closed reduction the new variation of external fixator should be preferred to the established variation or open reduction and crossed pinning.

HYBRID PLATING SHOWS EQUIVALENT BIOMECHANICAL BENDING STRENGTH TO UNICORTICAL LOCKED PLATING

Locking unicortical screw fixation of diaphyseal fractures may be clinically necessary due to internal constructs or prosthetic implants. The biomechanical effects of substituting one or more bicortical nonlocking screws to create a "hybrid" construct are unknown. Use of an initial nonlocking screw may be clinically desirable for creating initial plate-to-bone fixation prior to locking. A validated transverse fracture model was used with eighteen synthetic humerus models. Plate and screw fixation was performed in three treatment groups (n = 6): Unicortical locking screws only, fixation with two unicortical locking screws and one bicortical nonlocking screw on either side of the fracture and fixation with one unicortical locking screw and two bicortical locking screws on either side of the fracture. Displacement and gap strain measurements were made with a cyclic 4-point bending test. No significant differences were noted for construct stiffness or gap micromotion among the three groups on cyclic testing. Measurements at 1000, 5000, and 10,000 cycles showed stable fixation of all construct types with no significant changes in stiffness or micromotion. Substitution of one or more bicortical nonlocking screws in a unicortical locked construct does not affect construct stiffness or fracture gap strain. Data proven through controlled laboratory study.

Biomechanical testing of a new plate system for the distal humerus compared to two well-established implants

A biomechanical study was performed to test the hypothesis that a new anatomically preformed, thinner, soft-tissue protecting plate system for distal humeral fractures (Tifix®-hybridplate [HP]) would show comparable results in the quasi-static and dynamic testings compared to two conventional implants: The 3.5-mm reconstruction plate (RP) providing primary stability with normal bone mineral density (BMD), and a multidirectional locking plate (Tifix(®)-plate [P]) which can be used with poor bone quality. The Tifix(®)-HP was developed by the working group. The biomechanical testing was performed on a C2-fracture-model in 24 synthetic humeri. Three groups, each with eight bone-implant-constructs, were analysed in quasi-static and dynamic tests. The quasi-static measurements showed that under extension loading both locking plates (Tifix(®)-P, Tifix(®)-HP) were significantly stiffer than the reconstruction plate, and that the Tifix(®)-HP had a significantly lower stiffness than the two other implants under flexion loading. In the dynamic tests the Tifix(®)-P allowed significantly less fracture motion compared to the Tifix(®)-HP and the reconstruction plate. In an osteopaenic bone model locking plates failed only under much higher dynamic force than the reconstruction plate. The reconstruction plate and the Tifix(®)-P always failed through screw loosening, whereas the newly developed Tifix(®)-HP showed screw loosening in only one third of cases. The hypothesis that the newly designed plate system showed comparable results in the quasi-static and dynamic tests compared to the conventional implants with a significantly lower implant volume and thickness was confirmed.

Feasibility of a Braided Composite for Orthopedic Bone Cast

A tubular braided composite bone cast for improving the efficiency and quality of bone fracture treatment is investigated. Finite element analysis was used to evaluate stress concentrations in fracture sites supported with plate and tubular casts. The stress in a plated bone is 768 % of that in a whole bone at the same location, while it is only 47 % in a bone with a tubular cast. Three unbroken synthetic humeri were mechanically tested using an in-vitro long bone testing procedure developed in-house to find their stiffness at 20° and 60° abduction; these were found to be 116.8 ± 1.5 N/mm and 20.63 ± 0.02 N/mm, respectively. A 2 cm gap osteotomy was cut through the diaphysis in each bone. The bones were casted with a Kevlar/Cold cure composite, with calculated braid angles and thicknesses that Closely matched bone propoerties. The stiffness tests were repeated, and the results were within 10 % of the unbroken bone. This novel method of bone casting is promising if other clinical challenges can be minimized.

Stiffness and ultimate load of osseointegrated prosthesis fixations in the upper and lower extremity

BackgroundTechniques for the skeletal attachment of amputation-prostheses have been developed over recent decades. This type of attachment has only been performed on a small number of patients. It poses various potential advantages compared to conventional treatment with a socket, but is also associated with an increased risk of bone or implant-bone interface fracture in the case of a fall. We therefore investigated the bending stiffness and ultimate bending moment of such devices implanted in human and synthetic bones.MethodsEight human specimens and 16 synthetic models of the proximal femora were implanted with lower extremity prostheses and eight human specimens and six synthetic humeri were implanted with upper extremity prostheses. They were dissected according to typical amputation levels and underwent loading in a material testing machine in a four-point bending setup. Bending stiffness, ultimate bending moment and fracture modes were determined in a load to failure experiment. Additionally, axial pull-out was performed on eight synthetic specimens of the lower extremity.ResultsMaximum bending moment of the synthetic femora was 160.6±27.5 Nm, the flexural rigidity of the synthetic femora was 189.0±22.6 Nm2. Maximum bending moment of the human femora was 100.4±38.5 Nm, and the flexural rigidity was 137.8±29.4 Nm2. The maximum bending moment of the six synthetic humeri was 104.9±19.0 Nm, and the flexural rigidity was 63.7±3.6 Nm2. For the human humeri the maximum bending moment was 36.7±11.0 Nm, and the flexural rigidity at was 43.7±10.5 Nm2. The maximum pull-out force for the eight synthetic femora was 3571±919 N.ConclusionSignificant differences were found between human and synthetic specimens of the lower and upper extremity regarding maximum bending moment, bending displacement and flexural rigidity. The results of this study are relevant with respect to previous finding regarding the load at the interfaces of osseointegrated prosthesis fixation devices and are crucial for the development of safety devices intended to protect the bone-implant interface from damaging loadings.

Biomechanical analysis of pinning configurations for a supracondylar humerus fracture with coronal medial obliquity

Despite hundreds of studies of pinning configurations for transverse supracondylar humerus fractures, very few studies have investigated the optimal pin configurations in the treatment of supracondylar humerus fractures with coronal medial obliquity. The aim of this study was to develop a model of supracondylar humerus fractures with coronal medial obliquity and compare the stability of three various pin configurations to provide an acceptable pin placement. Oblique cuts were made in synthetic humeri at the level of the coronoid and olecranon fossae to simulate a humeral supracondylar fracture with coronal medial obliquity. Each fracture was reduced and fixed using two 0.062 inch K-wires in three different configurations, and sequentially tested in extension, varus, valgus, and internal and external rotations using an MTS 858 Minibionix materials testing load frame. We performed analysis of variance to compare construction stiffness of different pin configurations and the standard level of significant (P-value ≤ 0.05) was used indicate statistical significance. In resistance to extension and valgus loading, there was no statistical difference between all the three pin configurations (P=0.22 and 0.130, respectively). During the varus loading condition, the greatest stiffness values were obtained with the two crossed pin configuration, followed by the two medial pins, and the two lateral pin configuration showed the lowest values. For resistance in internal and external rotation testing, although there was no statistical difference between the two medial pins and the two crossed pins configurations (P=0.06 and 0.75, respectively), they were significantly greater than that of the two lateral pin configuration (P=0.003 and 0.004; P=0.001 and 0.02, respectively). In a synthetic humerus model of supracondylar humerus fractures with coronal medial obliquity, the two crossed pin configuration provided statistically greatest or comparable stability in the varus, and internal and external rotation loading conditions.