Symmetrical Faults Research Articles

Optimized hybrid osprey with PSO control for improved VSC-HVDC-wind power integration

Innovative power systems include offshore wind farms (OWFs) to generate electricity from renewable sources. So, reliable control systems are also necessary to make sure these power systems run smoothly. The purpose of this study is to combine the Osprey Optimization with Particle Swarm Optimization (OOPSO) to fine-tune the gains of Proportional-Integral (PI) controllers within the investigated wind energy conversion system (WECS) to enhance its performance. The study confirms the effectiveness of using the Hybrid OOPSO algorithm to optimize PI controllers in a WECS. The WECS includes two voltage source converter (VSC) stations at each end of a high voltage direct current (HVDC) transmission system. The transmission system links OWFs to the grid. The research demonstrates that the Hybrid OOPSO algorithm is superior to the genetic algorithm (GA) and PSO by enhancing setup stability and allowing fast voltage regaining following different fault cases. The introduced method performs more remarkably than traditional methods such as GA and PSO. The results of this study have shown that the proposed OOPSO enhances the overshoot in onshore voltage transient response under a symmetrical fault condition by 26% over PSO, 24% over GA, and 16% over OOA. The study is conducted using MATLAB/Simulink. The study underscores the importance of advanced optimization methods to guarantee offshore wind energy systems' efficient and dependable functioning.

Nonlinear integral backstepping control based on particle swarm optimization for a grid-connected variable wind energy conversion system during voltage dips

Double-fed induction generator (DFIG) wind turbines connected to the grid are particularly subject to grid problems such as voltage dips. Because of this, it might be challenging to maintain system stability and prevent system disconnections when using a Proportional-Integral (PI) Controller to operate this system. This paper applies the Integral Backstepping Control for the wind power plant system connected to the power grid. The Integral Backstepping is a nonlinear and recursive method that employs the Lyapunov theory to ensure the system's stability. The best selection of gain values for the Lyapunov function guarantees improved system control. These gains are frequently adjusted using the trial-and-error strategy, which is time-consuming and inefficient. This technique becomes more complex when many parameters need to be determined. It also limits the system's performance and restricts this nonlinear approach's advantages. The objective is to apply the particle swarm optimization for computing several constant values of the nonlinear approach by minimizing an integral absolute error criterion index. The weighted sum of errors is employed to solve the multiple objective problems. The proposed controller tracks the maximum power point, maintains the voltage of the DC-Link constant, and controls active and reactive power. The robustness of this method is verified in critical conditions, including system parameter variation and asymmetrical and symmetrical grid faults. The simulation findings highlight the effectiveness and robustness of the combination of Integral Backstepping with Particle Swarm Optimization in terms of reducing response time from 10.6 (ms) to 2 (ms), canceling static error, and improving overshoot compared to the vector control based on PI regulator. Besides, the DC-Link voltage ripples during the asymmetrical grid faults are reduced to ±1 (V) using the suggested controller. The latter can be implemented thanks to advancements in Central Processor Unit technology.

Improved Thermal Behavior of Multi-MW Power Converter Fed Pumped Storage Power Plant During Symmetrical Grid Fault

Improved Thermal Behavior of Multi-MW Power Converter Fed Pumped Storage Power Plant During Symmetrical Grid Fault

Application of the percentage differential relay and stator earth fault protection in synchronous generators

Abstract Synchronous generators play a vital role in the power system. The relay protection distributed in the system can quickly remove the fault, effectively respond to it, and solve the problem. In this paper, the characteristics of a synchronous generator neutral ungrounded are analyzed when various unsymmetrical and symmetrical faults occur in the internal and external areas, and the percentage differential relay is used to solve the problem of short circuit faults. For the single line-to-ground fault, the stator earth fault protection is also introduced to compensate for the shortcomings of the generator neutral ungrounded. The simulation software MATLAB/Simulink is applied for modeling and analysis, and the strategy of composite protection solves the problem of unsymmetrical failure for the neutral point ungrounding generator.

A smooth switching strategy for steady-state operation control and fault transient control of doubly fed induction generator

Abstract As the proportion of wind power generation systems in power systems continues to rise, their dynamic response during system malfunctions has gained significant importance. As the grid short-circuit ratio continues to decrease, traditional fault ride-through algorithms for wind power generators may no longer be applicable. This is evidenced by voltage oscillations under significant disturbances and overvoltage issues during low-voltage ride-through, which are further aggravated during asymmetric fault conditions. Therefore, this paper focuses on the low-voltage ride-through issues of doubly fed induction wind power generators in weak power grids. It investigates the steady-state operation and transient control schemes and proposes a smooth transition strategy for steady-state and fault transient operations of doubly fed wind power generators. This approach guarantees the synchronization of active and reactive power, mitigates steady-state reactive power imbalance, and prevents voltage fluctuations triggered by recurring low-voltage ride-through occurrences. Furthermore, during fault recovery, a ramped active power restoration approach is employed to mitigate the coupling of active and reactive power introduced by the phase-locked loop, enabling rapid and stable restoration of active and reactive power outputs. As a result, superior dynamic performance is achieved during both symmetric and asymmetric fault processes. Finally, the superiority of the proposed smooth transition strategy under different fault scenarios is validated through simulations with the RTLAB platform.

Novel glassbox based explainable boosting machine for fault detection in electrical power transmission system.

The reliable operation of electrical power transmission systems is crucial for ensuring consumer's stable and uninterrupted electricity supply. Faults in electrical power transmission systems can lead to significant disruptions, economic losses, and potential safety hazards. A protective approach is essential for transmission lines to guard against faults caused by natural disturbances, short circuits, and open circuit issues. This study employs an advanced artificial neural network methodology for fault detection and classification, specifically distinguishing between single-phase fault and fault between all three phases and three-phase symmetrical fault. For fault data creation and analysis, we utilized a collection of line currents and voltages for different fault conditions, modelled in the MATLAB environment. Different fault scenarios with varied parameters are simulated to assess the applied method's detection ability. We analyzed the signal data time series analysis based on phase line current and phase line voltage. We employed SMOTE-based data oversampling to balance the dataset. Subsequently, we developed four advanced machine-learning models and one deep-learning model using signal data from line currents and voltage faults. We have proposed an optimized novel glassbox Explainable Boosting (EB) approach for fault detection. The proposed EB method incorporates the strengths of boosting and interpretable tree models. Simulation results affirm the high-efficiency scores of 99% in detecting and categorizing faults on transmission lines compared to traditional fault detection state-of-the-art methods. We conducted hyperparameter optimization and k-fold validations to enhance fault detection performance and validate our approach. We evaluated the computational complexity of fault detection models and augmented it with eXplainable Artificial Intelligence (XAI) analysis to illuminate the decision-making process of the proposed model for fault detection. Our proposed research presents a scalable and adaptable method for advancing smart grid technology, paving the way for more secure and efficient electrical power transmission systems.

Ensembled methodology for the comtrade analysis regarding medium voltage side in wind park

This research proposes a methodology for automated COMTRADE analysis using ensembled algorithms for fault analysis in medium voltage circuits, specifically for wind park feeders. Traditional fault detection methods face significant limitations, such as CT saturation and DC offset, underscoring the need for improved approaches. The proposed methodology integrates Random Committee, XGBoost (XGB), and Light XGB algorithms, optimized through grid search, achieving an accuracy of 99.397 %. This ensemble approach significantly reduces classification errors, false positives, and false negatives compared to single algorithm methods. This research has the analysis of 3929 events for training and 829 fault events for test, it revealed a high correlation between current and fault spectra; the methodology demonstrated superior performance in fault location analysis, with terminal faults showing the most severe transient recovery voltage (TRV) peak values, while kilometer faults exhibited higher transient recovery restoration voltage growth rates. The fault location analysis was conducted by comparing simulation-derived overvoltage with standard TRV graphs, aligned with IEC 62271-100 standards. Circuit breakers exhibited higher TRV tolerance with lower fault currents. Terminal faults, particularly symmetrical three-phase faults, were identified as the most severe, typically occurring at peak TRV values. Its findings reduced classification errors, from 41 to 5 events, and decreased the false negative rate from 1.81 % to 0.24 % compared to Random Forest. Validation with virtual relays showed a reduction in RCE from 5.3 % to 0.63 %.

A new approach to instantaneous power based control of DFIG using active disturbance rejection control

This paper presents the design and control of a wind energy converter system that uses a doubly fed induction generator. It introduces a model that incorporates instantaneous active and reactive power as state variables to represent both the stator and rotor sides of the doubly fed induction generator. Subsequently, a linear active disturbance rejection-based control regulator is proposed for the control loops. The parameters of the linear active disturbance rejection controllers (ADRC) are adjusted by two methods: the single parameter tuning approach and the genetic algorithm (GA) method. The performance of the suggested controller is ultimately compared with a tuned proportional-integral (PI) control regulator in the MATLAB environment. In order to examine the performance of the system, various test scenarios are taken into account. These scenarios include different percentages of load change in both sub-synchronous and super-synchronous modes of operation, faults with different fault periods are considered in both modes of operation. The conventional PI controller-based approach requires 35 control cycles to reach steady state under load change conditions and 50 control cycles under symmetrical fault conditions, regardless of whether the system is operating in sub synchronous or super synchronous mode. The single parameter-based tuned ADRC approach only requires 15 control cycles for load change and 20 control cycles for symmetrical fault scenarios. In contrast, for both the load change and symmetrical fault scenarios, the ADRC with GA-based parameter tuning reaches steady state in just 5 control cycles. Furthermore, a case involving wind speed variation is presented to demonstrate the maximum power point tracking capability of the proposed control structure. Similarly, for the robustness test of the control regulator, variations in resistance and inductance are introduced to observe their impact on the response of the control regulators. Finally, a real-time hardware in loop setup is presented to validate the control strategy during the load change in the sub-synchronous mode of operation of the doubly fed induction generator.

A Pilot Protection of Negative Sequence and Additional Network Considering Photovoltaic Integration

Background: Introducing pilot protection in active distribution networks containing PV can improve the reliability and selectivity of protection. However, the basic communication facilities of the existing distribution network make it difficult to meet the requirements of data synchronization, and the PV T-connection to the network leads to sudden changes in the impedance angle. Methods: Therefore, pilot protection of a negative sequence and additional network considering PV is proposed. The scheme is based on the feature that the PV model only outputs positive sequence components after a fault. For asymmetrical faults, the negative sequence impedance detected at both ends of the protection is utilized to construct a comparative negative sequence impedance protection criterion. For symmetrical faults, the voltage characteristics of the faulty additional network are utilized to construct a protection criterion. Results: Finally, an actual distribution network model with PV is constructed in PSCAD to verify the effectiveness and reliability of the protection method. Conclusion: The protection method is selective and reliable and is not affected by high penetration rate and PV fault characteristics.

Artificial Hummingbird Algorithm-based fault location optimization for transmission line

Transmission is an important aspect regarding an effective designing of electric supply system. Ensuring reliable and fault-free transmission from the source for effective distribution to the end consumers is very much desirable. In this respect, fast and accurate fault detection, particularly in the overhead transmission lines, is very pertinent. Various algorithms and novel approaches have been formulated by various researchers aligned to this challenge. In this context, a new algorithm influenced by the biotic procedure of flight skills of hummingbird seems to be one of the best algorithms to address the cited problem. This paper focuses on the formulation of this Artificial Hummingbird Algorithm (AHA) and its high accuracy in ameliorating the fault location in transmission line. The most common flight skills being used in the algorithm are foraging schemes, which includes axial, diagonal, and omnidirectional flights. The proposed AHA has been tested using the Simulink prototype in MATLAB for an overhead transmission line having a length of 300 km and system voltage of 400 kV at suitable lengths. Specimen signal of voltages and currents waveforms has been taken at duo ends of the overhead transmission line. The results of the proposed algorithm have been compared with the results obtained from previous studies, and it has been observed that this algorithm yields better results for various kinds of asymmetrical and symmetrical faults.

A fault ride-through strategy for grid-forming converters under symmetrical and asymmetrical grid faults

In order to maintain grid-forming converter (GFM) voltage source behaviour under current limiting mode, a threshold virtual impedance (TVI) current limiting control is proposed, which is controlled in the positive and negative sequence synchronous reference frames for symmetrical and asymmetrical fault conditions. The converter current is strictly limited within the maximum limit without the need for current saturation limiters. Since the TVI control is based on 3-phase sinusoidal currents, it is shown that using the measured current instead of the existing current reference for the TVI control may cause oscillatory behaviour when a large switching delay is considered. Since sequence extraction control is necessary, the paper also compares GFM dynamic stability under the three well-known sequence extraction methods (i.e. delay cancellation, dual second order generalized integrator, and decoupled double synchronous reference frame). It is shown that the differences are small when GFM is not in current limiting mode, but they are large when GFM is in current limiting mode or switching delays are considered.

Envelope based symmetrical fault detection during power swing for series compensated lines

Envelope based symmetrical fault detection during power swing for series compensated lines

Adaptive low voltage crossing strategy for symmetrical faults of networked inverters

Abstract Due to the inability of grid-following control methods to compensate for the comprehensive reduction in system inertia, strength, and short-circuit capacity caused by the decreased proportion of synchronous machines, the grid exhibits insufficient resilience to disturbances, leading to severe stability risks in terms of rotor angle, frequency, and voltage. Grid-forming inverters have emerged to address this issue. During symmetrical faults, the low-voltage ride-through of grid-forming inverters often involves freezing the reactive power loop, resulting in a direct output of higher voltage and reactive current. However, an increase in reactive power command leads to a sharp rise in the internal potential magnitude of grid-forming inverters. Upon clearance of the grid fault, the excessively high internal potential may cause a rapid, short-term increase in terminal voltage, potentially resulting in overvoltage, which is detrimental to the operation of grid-connected equipment. In response to this issue, this paper proposes an adaptive low-voltage ride-through control strategy for grid-forming inverters under symmetrical faults controlled by a virtual synchronous machine control method. Initially, a virtual synchronous machine control model is established. Limiting current is achieved through the construction of a fixed virtual impedance loop. The issues associated with fixed virtual impedance current limiting are analyzed, leading to the proposal of an adaptive virtual impedance control strategy. Finally, the feasibility of the proposed method is verified through simulation experiments.

Adaptive reactive power control strategy for grid-forming inverter under symmetrical fault

Abstract Due to the inability of the grid-type control method to compensate for the comprehensive reduction in system inertia, strength, and short-circuit capacity caused by the proportional decrease of synchronous machines, the power grid exhibits insufficient resistance to disturbances, leading to severe stability risks in terms of rotor angle, frequency, and voltage. In response to these challenges, grid-forming inverters have emerged. Under symmetrical faults, the low-voltage ride-through of grid-forming inverters is often accompanied by a frozen reactive power environment, resulting in a direct output of increased voltage and reactive current. However, an elevated reactive power command can cause a sharp increase in the potential amplitude within grid-forming inverters. After the grid fault is cleared, the excessively high internal potential can cause a short-term and rapid increase in terminal voltage, potentially leading to overvoltage, which is detrimental to the operation of grid-connected devices. To address this issue, this paper first employs a grid-forming inverter controlled by a virtual synchronous machine control method. Using the grid positive-sequence voltage as a reference value, it identifies whether a voltage drop fault has occurred. Based on this, an adaptive reactive power control strategy is proposed, which can promptly achieve the same effect as the frozen reactive power environment during faults, while also promptly restoring the reactive power environment after fault clearance, thereby avoiding overvoltage issues. The feasibility of the proposed method is verified through the establishment of a simulation system.

Comparative analysis and implementation of DC microgrid systems versus AC microgrid performance

DC power systems have emerged as a cost-effective solution for electric power generation and transmission, challenging the dominance of AC distribution systems. However, a comprehensive efficiency comparison between DC and AC microgrids remains understudied. This study seeks to explore and conduct a thorough survey on development and designing of DC microgrids to address this gap. Firstly, a comprehensive literature review comparing the efficiencies of AC and DC microgrids has been presented. The analysis highlights the superior efficiency of DC distribution systems over AC systems, supported by detailed advantages. Secondly, hardware implementation has been performed to directly compare the efficiency of DC versus AC systems. Research validity and application are further improved by the hardware prototype’s scalability, which in simulation allows for a thorough assessment of system stability over a range of scenarios from four to six terminals. Test results from the built hardware prototype demonstrate an astounding 15% increase in efficiency using the DC system compared to the AC system, demonstrating its potential for improved performance in real-world scenarios. In simulation results, the designed DC microgrid demonstrates stable voltages of 500V under steady state operation and rapid recovery within 80 ms under both symmetrical and asymmetrical faults has been observed. The research being investigated utilizes hardware implementation and simulation to provide useful insights into the efficiency and stability of DC microgrids in comparison to AC systems. These results are important for developing robust power distribution networks in modern energy environments, promoting sustainability and dependability in infrastructure growth.

A Stabilization Control Strategy for Wind Energy Storage Microgrid Based on Improved Virtual Synchronous Generator

In high-penetration renewable-energy grid systems, conventional virtual synchronous generator (VSG) control faces a number of challenges, especially the difficulty of maintaining synchronization during grid voltage drops. This difficulty may lead to current overloads and equipment disconnections, and it has an impact on the security and reliability of the system, as well as limiting the dynamic reactive power support capability of the system. To solve this problem, in this study, a wind–solar hybrid power generation system is designed with a battery energy storage device connected on the DC side, and proposes a low voltage ride-through (LVRT) control strategy for the grid-connected inverter based on an improved VSG. The control strategy employs an integrated current limiting technique combining virtual impedance and vector current limiting to ensure that the VSG exhibits good dynamic power support characteristics during symmetrical faults by adjusting the setpoint value of reactive power. At the same time, it maintains the synchronization and power angle stability of the VSG itself to achieve the goal of LVRT. Simulation results show that the proposed control strategy can effectively suppress the renewable power fluctuations (about 30% reduction in fluctuations compared to the conventional strategy) and ensure the safe and reliable operation of the renewable energy sources and VSGs during grid-side faults. In addition, it provides a given reactive power support and stable grid voltage control (voltage dips reduced by about 20%), which significantly enhances the LVRT capability of the hybrid wind–solar-storage generation system.

Experimental analysis of a multi-phase resonance-based fault current limiter prototype under symmetrical and asymmetrical faults

Expansion of power systems and involving more distributed generation cause to increase in fault current levels. This paper presents a three-phase resonance-based solid-state fault current limiter (FCL) prototype that has series and parallel resonance modes developed to suppress fault currents of power systems. The laboratory-scaled prototype is located on a three-phase test circuit and has been examined with the fault types of three-phase, three phase-to-ground, two phase-to-ground, and phase-to-ground. The performance and effectiveness of the proposed series-parallel resonance-type fault current limiter (SPRFCL) are validated with the comparison of Matlab/Simulink simulations and experimental test results. Fault currents in different types of faults are limited to an allowable value at high rates and experimental results are considerably close to current values obtained from each fault simulation. Fault currents of faulted phases are restricted with the limiting rates ranging from 75 % to 85 % concerning prospective fault currents in the non-FCL situations. Short-circuit test results of the prototype of SPRFCL that is supplied from a 380 V grid revealed that it acts stable and successful operation regardless of fault type. Accordingly, it has a favorable circuit design for power system applications.

Design of Radial Distribution System to Study Load-Flow and Short Circuit Analysis Using ETAP Software

This work's analysis provides information on fault analysis and load flow studies, which help to understand how radial distribution networks operate both in normal and emergency circumstances. The research explores optimization methods, describing capacitor placement, transformer size, and feeder reconfiguration in order to lower losses and increase system efficacy. Moreover, the work looks at reliability-focused maintenance techniques, stressing the need of predictive maintenance and condition monitoring in raising the dependability of radial distribution networks. Modern electrical power networks depend heavily on their radial distribution system, which effectively and dependable distributes electricity to customers. Many radial distribution system-related topics are covered in detail on this website, including analytical methods, optimization processes, and dependability enhancement strategies. Power flow, voltage control, and losses in radial networks are investigated in this paper under a range of operational situations. The last and crucial stage of a power system, the electrical distribution system makes sure that customers have a steady supply of electricity. Regretfully, because it is often neglected and exposed to environmental risks, our distribution network has a number of problems. Our distribution feeder is rigorously analyzed for load flow and short-circuits in order to overcome these challenges and find and fix problems. The main topics of this study are the load flow and short-circuit analysis of a radial distribution feeder, which is mostly constructed with (ETAP). The final and crucial part of a power system, the electrical distribution system ensures that consumers receive an uninterrupted and steady supply of electricity. Our distribution feeder undergoes a rigorous and cautious process to address these issues front on because of the uncontrollable nature and susceptibility of our network to environmental hazards. This paper delves deeply into the issues of short-circuiting and load flow in radial distribution feeders. Both symmetrical and asymmetrical faults are thoroughly investigated by mathematical computations and ETAP simulations; the results of the software simulations are contrasted with those of the mathematical analysis. These discoveries will definitely influence the development and management of our system and point us in the direction of workable and practical solutions.

A chaos game optimization algorithm-based optimal control strategy for performance enhancement of offshore wind farms

This paper presents a novel application of the chaos game optimization (CGO) algorithm to optimally design PI controllers for power electronic interface circuits of offshore wind farms (OWF) consisting of a permanent magnet synchronous generator powered by a variable-speed wind turbine. The OWF is linked to the network via a high-voltage direct current (HVDC) transmission system. The CGO metaheuristic method is employed to fine-tune voltage source converter (VSC)-based HVDC transmission systems’ proportional-integral controller gains. The study explores multiple strategies to extract the highest power from the system while ensuring stability under symmetrical and unsymmetrical fault conditions. The CGO algorithm consistently yields superior results to other algorithms, improving system regaining and stability post disturbances. Consequently, the technique enhances the dynamic and transient stability of the OWF. The detailed study is implemented using MATLAB/Simulink.

LVRT Enhancement of DFIG-based WECS using SVPWM-based Inverter Control

Abstract: Across many countries, wind turbine generation systems (WTGS) have been established over the past few decades. In this paper, we augment the low voltage ride-through (LVRT) enrichment facility of driving a DFIG-based wind energy conversion system (WECS) using space vector pulse width modulation (SVPWM)-based inverter control. The proposed technique employs an SVPWM-based control algorithm to regulate the voltage and frequency of the output power during grid faults, thereby enhancing the WECS's ability to remain connected to the grid and provide power. The study focuses on decreasing transient current throughout the instant of fault. Modeling and control approaches were also discussed in this study. The performance of the proposed technique is evaluated using MATLAB/Simulink simulations, and the results demonstrate that the technique effectively improves the LVRT capability of the DFIG-based WECS. Background: Due to the variation in wind speed, the power generated by wind turbines is inconsistent. The power generated and the losses in wind turbines change correspondingly with changes in wind speed. The only type of machine that can generate power at speeds below the fixed speed is the doubly-fed induction generator (DFIG). But DFIG is oversensitive to network faults, which makes the bidirectional converters and DC link capacitor fail due to high inrush current and over-voltage. Methods: The converters connected to DFIG consist of an AC-to-DC converter, a boost converter, and a space vector pulse width modulation (SVPWM)-based DC-AC converter. The performance of the SVPWM controller is analyzed during symmetrical and unsymmetrical fault conditions. Results: The anticipated control provides adequate reactive power support to the network through the time of the fault and improves voltage and current waveform. The reactive power flow is also analyzed, and the effectiveness of the proposed controller is verified using MATLAB and Simulink. Conclusion: SVPWM (Space Vector Pulse Width Modulation)-based inverter control is an effective technique for wind energy conversion systems (WECS). The use of SVPWM can provide accurate and precise control of the AC voltage generated from the DC voltage source, resulting in improved system efficiency and reduced harmonic distortion in the output waveform. : The comparative analysis of THD suggests that SVPWM is a superior technique compared to other inverter control techniques such as sine-triangle pulse width modulation (SPWM) and carrier-based pulse width modulation (CPWM). SVPWM can help to reduce the distortion in the output waveform, leading to improved system efficiency, reduced wear on the system components, and overall better performance of the WECS. Furthermore, SVPWM offers several advantages over other inverter control techniques, including better utilization of DC voltage, improved voltage control, and better utilization of switching devices. These advantages make SVPWM a valuable tool for optimizing the operation of WECS and improving the reliability and performance of renewable energy systems. The value of THD for SVPWM inverter control in WECS is 1.53 under symmetrical fault and 1.34 for unsymmetrical fault, respectively. In summary, the use of SVPWM-based inverter control for WECS is an effective way to improve the efficiency and performance of the system while reducing the distortion in the output waveform and providing adequate reactive power support. The advantages of SVPWM over other inverter control techniques make it a valuable tool for the development and optimization of renewable energy systems.