Suspended Mineral Research Articles

Geochemical drivers of manganese removal in drinking water reservoirs under hypolimnetic oxygenation

Manganese (Mn) is a naturally occurring contaminant commonly found in drinking water supplies. In lakes and reservoirs, water authorities increasingly use in situ treatment by hypolimnetic oxygenation (HOx) systems to remove metals such as Mn from the water column. HOx systems introduce dissolved oxygen (DO) to the bottom waters (hypolimnion) to promote oxidation and subsequent removal of metals from the water column. Previous laboratory studies have shown the importance of individual geochemical drivers (pH, alkalinity, mineral surfaces) on Mn oxidation, but few studies have examined the influence of these drivers of Mn removal in concert. In this study, we conducted field monitoring and laboratory experiments to examine how pH, alkalinity and the presence of mineral particles influence Mn removal at two drinking water reservoirs in southwest Virginia, both with HOx systems: Falling Creek Reservoir (FCR) and Carvins Cove Reservoir (CCR). Both reservoirs have had historical issues with elevated (>0.05 mg/L) Mn concentrations during seasonal stratification (May–October). Watershed geology contributes to differences in pH and alkalinity between the reservoirs, with FCR having lower historical medians of hypolimnetic pH and alkalinity (6.6 and 18 mg/L CaCO3, respectively) than CCR (7.2 and 62 mg/L CaCO3, respectively).Results of laboratory experiments examining the influence of pH on Mn removal showed substantial Mn loss within 14 days only under high pH (10) conditions. Mn removal did not occur at pH 6 or 8 over the same 14-day period. In experiments with pH 10 and alkalinity >70 mg/L CaCO3, near-total Mn removal occurred within 2 h. Mn removal occurred concurrently with precipitation of microscopic (<5 μm) particles, followed by formation of macroscopic (>100 μm) particles. Particles of both size classes were identified as Mn oxides (MnOx). These observations suggest that increasing pH and alkalinity promotes Mn oxidation and subsequent removal from solution. Results of experiments with pH 10 and alkalinity >70 mg/L CaCO3 suggest that heterogeneous oxidation by MnOx partially drives rapid Mn removal. Thus, initial formation of MnOx creates a positive feedback loop that can enhance additional Mn loss. In experiments using water collected from FCR and CCR, we observed rapid Mn removal in unfiltered water (0.002–0.05 d−1) but no significant removal of Mn in filtered water. These results, in combination with results of analysis of particles collected from reservoir water, suggest that minerals present in the water column likely catalyze MnOx formation. Together, our experimental results suggest that heterogenous oxidation is an important process of Mn removal, while pH and alkalinity variations of the range expected in natural freshwaters contribute less to differential Mn removal. The formation of MnOx particles during in situ oxygenation, as well as the presence of suspended minerals that occur naturally in water columns, play an important role in promoting Mn oxidation and should be accounted for in Mn removal treatment strategies.

Stratified water columns: homogenization and interface evolution

Stratified water columns are often found in lakes and oceans. Stratifications result from differences in density due to salt concentration, temperature, solid content and oxygenation. The stability of stratifications affects bioactivity, sedimentation, contaminant transport and environmental remediation. This study investigates the evolution of 6 stratified water columns created by differences in salinity, suspended minerals and the presence of a bottom heat source. We use acoustic wave reflection, photography, and both electrical conductivity and temperature profiles to track changes in stratification. Results show that multiple concurrent processes emerge across layers in otherwise quiescent water bodies. Dissimilar chemo-thermo conditions give rise to chemical and thermal diffusion, convection, and double-diffusion convection. When stratification involves suspended particles, interlayer processes include diffusiophoresis, flocculation/aggregation, sedimentation, osmosis, and chemo-consolidation; in this case, the specific surface and surface charge of suspended particles, and the salt concentration in contiguous layers determine aggregation-sedimentation-consolidation patterns. The interlayer transition zone acts as a high-pass filter that preferentially reflects low-frequency long-wavelength P-waves; invasive thermal and electrical conductivity probes provide complementary information and may identify stratification even when it is undetected by acoustic signals.

Patterns of the relationship between the Secchi disk depth and the optical characteristics of water in the Neva Estuary (Baltic Sea): the influence of environmental variables

The Secchi disc depth (Dsd) measurement is widely used to monitor eutrophication and the quality of the aquatic environment. This study aimed to investigate the relationship between Dsd and various factors, including the coefficient of attenuation of photosynthetically active radiation [Kd (PAR)], the depth of the euphotic zone (Deu), PAR at the Secchi disk depth (Esd) and the absorption coefficient of PAR (F) in the Neva Estuary, one of largest estuaries of the Baltic Sea. Environmental variables impacting these indices were identified using data collected from midsummer 2012 to 2020. The Dsd values in the estuary ranged from 0.3 to 4.0 m, with an average value of 1.8 m, while the Deu/Dsd ratio ranged from 1.5 to 6.0 with an average value of 2.8. These values were significantly lower than those observed in the open waters of the Baltic Sea. The highest Deu/Dsd ratio was observed in turbid waters characterized by high Kd(PAR) and low Dsd. Contrary to expectations, Dsd did not exhibit a significant relationship with the concentration of chlorophyll a, raising doubts about the utility of historical Dsd data for reconstructing phytoplankton development in the estuary. Principal component analysis did not identify the primary environmental variables strongly affecting the optical characteristics of water. However, recursive partitioning of the dataset using analysis of variance (CART approach) revealed that the concentration of suspended mineral matter (SMM) was the primary predictor of Deu/Dsd, Kd(PAR), and F. This SMM was associated with the frequent resuspension of bottom sediments during windy weather and construction activities in the estuary. Concentrations of suspended organic matter and the depth of the water area were found to be less significant as environmental variables. Furthermore, the CART approach demonstrated that different combinations of environmental variables in estuarine waters could result in similar optical indicator values. To reliably interpret the data and determine the optical characteristics of water in estuaries from Dsd, more complex models incorporating machine learning and neural connections are required. Additionally, reference determinations of Esd in various regions with specific sets of environmental variables would be valuable for comparative analyses and better understanding of estuarine systems.

Synthesis of Polyaluminum Chloride Coagulant from Waste Aluminum Foil and Utilization in Petroleum Wastewater Treatment

This work investigates the potential synthesis of cost-effective polyaluminum chloride (PACl) coagulant from waste household aluminum foil and utilization for treating petroleum wastewater (PWW), especially dissolved organic compounds (DOC, like octanol–water mixture) and nonsettleable suspended (NSS-kaolin) mineral particles. Based on the Standard Practice for Coagulation–Flocculation Jar Test, the efficiency of PACl for DOC and NSS removal was evaluated in relation to the effects of the operational parameters. The results demonstrated that the as-prepared PACl has an amorphous morphology with a Keggin-type e-Al13 molecular structure {Na[AlO4(OH)24(H2O)]·xH2O and good thermal stability up to 278 °C. PACl coagulant also exhibited a higher efficiency for NSS removal than DOC by around 1.5- to 1.9-fold under broad pH (5–7), while a higher acidic/alkaline pH disrupts the sweep floc formation. An increased PACl dosage (over 25 mg/L) also caused a decrease in the coagulation efficiency by 11.7% due to Al species’ transformation and pH depression (from 6.8 to 4.9) via increased PACl hydrolysis. With a fast rotating speed of 280 rpm for 2 min, the minimum dose of PACl (10–25 mg/L) can maximize the removal efficiency of NSS (~98%) and DOC (~69%) at pH 6.5 ± 0.5 and 35 °C after 30 min of settling time. Treating actual saline PWW samples (salinity up to 187.7 g/L) also verified the high efficacy of PACl coagulation performance in reducing the turbidity and dissolved hydrocarbons by more than 75.5% and 67.7%, respectively. These findings verify the techno-economic feasibility of the as-prepared PACl coagulant in treating PWW treatment at different salinity levels.

Sorption of oxytetracycline to microsized colloids under concentrated salt solution: A perspective on terrestrial-to-ocean transfer of antibiotics

The sorption of antibiotics on soil minerals and their cotransport have been widely studied for the past few years; however, these processes in concentrated salt solutions (estuary-like conditions) are not fully understood. This study aims to determine the possible sorption of oxytetracycline (OTC) on various natural and synthesized microsized minerals (including haematite, goethite, kaolinite, bentonite, lateritic, kaolinitic and illitic soil clays) under conditions mimicking pure, fresh, brackish and sea waters. The sorption of OTC was found to decrease in surface charge (herein zeta potential), hence altering the colloidal properties of the materials used. The sorption capacities of soil clays for OTC follow the inequality illitic soil clay > kaolinitic soil clay > lateritic soil clay, and the sorption capacities were found to decrease at higher salt concentrations. Seawater can intensify the release of the sorbed OTC from soil clay surfaces while favouring the coaggregation of the remaining OTC with soil clays. This implies that the long-range transport of OTC or other similar antibiotics can be governed by the mineralogical composition/properties of the suspended particles. More importantly, increasing salt concentrations in estuaries may form a chemical barrier at which limited amounts of OTC/antibiotics can pass through, while the remaining OTC/antibiotics can be favoured to aggregate simultaneously with suspended mineral particles.

Electrocoagulation in a packed aluminium scraps anode reactor for mineral processing wastewater treatment

Efficient treatment and purification of mineral processing wastewater (MPW) have not been sufficiently investigated in the past though they are of great importance for sustainable mineral processing. Herein, a unique electrocoagulation (EC) reactor with aluminium scraps as anode material was developed for the treatment of real industrial MPW containing residual flotation reagents (major contributor to chemical oxygen demand, COD) and suspended particles. It was found that the active coagulants produced from the dissolution of aluminium scraps can play a key role in the purification of MPW. Under the conditions of initial pH 9, current 1 A, and processing time 90 min, the removal rate of COD was 74% while the turbidity can be almost completely removed. The mechanism lies in that most of the flotation reagents was adsorbed on the surfaces of suspended mineral particles, namely, montmorillonite, quartz, garnet, chlorite and mica, and then precipitated with the mineral particles. This innovative technology of utilizing wasted aluminium scraps to treat MPW is in line with the green development.

Combined effects of chemical dispersant and suspended minerals on the dispersion process of spilled oil

The dispersion process of spilled oil is an important concern for the effective disposal of oil spills. The dispersed oil concentration and oil droplets size distribution were studied through a wave tank test under the application of chemical dispersant and suspended minerals. The results indicated that dispersant and minerals increased the dispersed oil concentration and the effect of dispersant was more significant, and they had a synergistic effect on oil dispersion. When dispersant and minerals were applied together, the volume mean diameter of oil droplets decreased in the first 30 min, then increased and reached a maximum value at 90–120 min, and decreased again. Moreover, suspended minerals could inhibit the coalescence of oil droplets. This study can afford data support for oil spill emergency response that occurs in inshore or estuaries.

Impact of the Construction of New Port Facilities on the Biomass and Species Composition of Phytoplankton in the Neva Estuary (Baltic Sea)

The construction of new port facilities and the creation of new lands is a natural consequence of the rapid growth in the population of ocean coastlines. Despite the fact that such human activity is becoming more and more widespread, its impact on various components of aquatic ecosystems, including phytoplankton, is still poorly understood. The aim of the study was to assess the effect of the large-scale construction of new port facilities on biomass and taxonomic composition of phytoplankton in the Neva Estuary (northeastern Baltic Sea). Studies have shown that digging and displacing large amounts of bottom sediments during these works led to a significant increase in suspended mineral matter and a decrease in water transparency in the estuary. This significantly reduced the species richness and biomass of phytoplankton. However, the analysis of beta diversity did not show significant changes in the phytoplankton community during the periods of port construction and the periods when no works were carried out. The changes mainly concerned rare species, while the occurrence and biomass of dominant and subdominant species changed to a lesser extent. Due to various adaptations, the phytoplankton species common in the estuary are apparently able to survive under prolonged shading and successfully compete with species that are unable to withstand the lack of light for a long time. To correctly take into account the effects of the construction of new port facilities on phytoplankton and, if possible, minimize it, additional studies of the ecology of certain phytoplankton species, their relationships, and physiological responses to various environmental factors are required.

Coaggregation of micro polystyrene particles and suspended minerals under concentrated salt solution: A perspective of terrestrial-to-ocean transfer of microplastics

This study evaluates the colloidal stability of polystyrene microplastics (PSMPs) in the presence of various mineral colloids. Although PSMPs were highly dispersive, they were found to be involved in the aggregation of each mineral colloid. The efficiency of mineral colloids to stimulate the coaggregation of PSMPs follows the order bentonite > kaolinitic soil clay > illitic soil clay > kaolinite > goethite > haematite. Surface charge density is likely a crucial factor that determines the efficiency of mineral colloids. In concentrated salt solution, PSMPs together with mineral colloids can be involved in various continuous and simultaneous electrochemical processes such as charge neutralization, double electric layer compression, van der Waals attraction stimulation and heteroaggregation. These processes may also occur in the estuary environments, where suspended mineral colloids may play an ultimate role in reducing the transport of microplastics into oceans while also intensifying microplastic enrichment in coastal sediments.

Supervised Classifications of Optical Water Types in Spanish Inland Waters

Remote sensing of lake water quality assumes there is no universal method or algorithm that can be applied in a general way on all inland waters, which usually have different in-water components affecting their optical properties. Depending on the place and time of year, the lake dynamics, and the particular components of the water, non-tailor-designed algorithms can lead to large errors or lags in the quantification of the water quality parameters, such as the suspended mineral sediments, dissolved organic matter, and chlorophyll-a concentration. Selecting the most suitable algorithm for each type of water is not a simple matter. One way to make selecting the most suitable water quality algorithm easier on each occasion is by knowing ahead of time the type of water being handled. This approach is used, for instance, in the Lake Water Quality production chain of the Copernicus Global Land Service. The objective of this work is to determine which supervised classification approach might give the most accurate results. We use a dataset of manually labeled pixels on lakes and reservoirs in Eastern Spain. High-resolution images from the Multispectral Instrument sensor on board the ESA Sentinel-2 satellite, atmospherically corrected with the Case 2 Regional Coast Colour algorithm, are used as the basis for extracting the pixels for the dataset. Three families of different supervised classifiers have been implemented and compared: the K-nearest neighbor, decision trees, and support vector machine. Based on the results, the most appropriate for our study area is the random forest classifier, which was selected and applied on a series of images to derive the temporal series of the optical water types per lake. An evaluation of the results is presented, and an analysis is made using expert knowledge.

Seasonally variable interactions between dissolved organic matter and mineral particles in an agricultural river

Streams and rivers form an important link in the global carbon cycle by transporting and transforming large amounts of carbon imported from terrestrial ecosystems to the oceans. Since streams in agricultural areas often experience increased concentrations of suspended mineral particles from soil erosion, they are important sites where dissolved organic carbon (DOC) may be adsorbed to particles and retained in the sediment. As the extent of adsorption varies with the molecular composition of dissolved organic matter (DOM), which is seasonally variable, we expect also the fraction of organic material that adsorbs to mineral particles to fluctuate over time. We sampled the agriculturally impacted River Fyrisån (Sweden) monthly during 1 year, and measured DOC concentration and DOM composition based on several optical properties. At each sampling occasion, we estimated the potential for adsorption by exposing the samples to a reference clay. The potential for adsorption was greatest when riverine DOM had the most terrestrial character, as this fraction of the DOM pool was selectively adsorbed to clay surfaces. The extent of adsorption was negatively related to the concentration of base cations, most notably calcium. We suggest that the observed relationships between the potential for adsorption, DOM composition and base cations are linked by discharge. A bioavailability test at one sampling occasion suggested that DOM remaining after exposure to clay particles was more biodegradable. This implies that adsorption may alter the degradation potential of DOM remaining in solution, which could have far reaching effects on the fate of organic carbon.

Satellite observations estimating the effects of river discharge and wind-driven upwelling on phytoplankton dynamics in the Chesapeake Bay.

Phytoplankton growth in estuaries is regulated by a complex combination of physical factors with freshwater discharge usually playing a dominating role controlling nutrient and light availability. The role of other factors, including upwelling-generating winds, is still unclear because most estuaries are too small for upwelling to emerge. In this study, we used remotely sensed proxies of phytoplankton biomass and concentration of suspended mineral particles to compare the effect of river discharge with the effect of upwelling events associated with persistent along-channel southerly winds in the Chesapeake Bay, a large estuary where upwelling and its effects on biogeochemical dynamics have been previously reported. The surface chlorophyll-a concentrations (Chl-a) were estimated from Visible Infrared Imaging Radiometer Suite (VIIRS) satellite data using the Generalized Stacked-Constraints Model (GSCM) corrected for seasonal effects by comparing remotely sensed and field-measured data. Light limitation of phytoplankton growth was assessed from the concentration of suspended mineral particles estimated from the remotely sensed backscattering at blue (443 nm) wavelength bbp (443). The nine-year time series (2012-2020) of Chl-a and bbp (443) confirmed that a primary factor regulating phytoplankton growth in this nearshore eutrophic area is discharge from the Susquehanna River, and presumably the nutrients it delivers, with a time lag up to four months. Persistent southerly wind events (2-3 days with wind speed >4 m/s) affected the water column stratification in the central part of the bay but did not result in significant increases in remotely sensed Chl-a. Analysis of model simulations of selected upwelling-favorable wind events revealed that strong southerly winds resulted in well-defined lateral (East-West) responses but were insufficient to deliver high-nutrient water to the surface layer to support phytoplankton bloom. We conclude that, in the Chesapeake Bay, which is a large, eutrophic estuary, wind-driven upwelling of deep water plays a limited role in driving phytoplankton growth under most conditions compared with river discharge. Integr Environ Assess Manag 2022;18:921-938. © 2022 SETAC.

Mixed-dust pneumoconiosis in a dental technician: a multidisciplinary diagnosis case report

BackgroundIn dental laboratories, exposure to crystalline silica can occur during procedures that generate suspended mineral dusts, e.g. dispersion of mixing powders, removal of castings from molds grinding, polishing of castings and porcelain, and use of silica sand for blasting. There is also a large list of toxic agents (acrylic resins, polymeric materials, etc.) used to produce removable and fixed prostheses, but also impression materials and more. Using personal protective equipment and other aids reduces the exposure to these potentially harmful agents.Case presentationWe report the case of a 42-year-old male dental technician who began to suffer from a dry cough and exertional dyspnea after approximately 15 years of work. The operations he conducted for his job resulted in the generation of crystalline silica, aluminum, chromium and titanium dust. The worker did not regularly wear personal protective equipment and some of the above operations were not carried out in closed circuit systems. The Chest X-ray showed diffused micronodules in the pulmonary interstitium of the upper-middle lobes, bilaterally, and a modest left basal pleural effusion. Simple spirometry showed small airway obstruction in its initial stage. High Resolution Computerized Tomography of the chest showed bilateral micronodulation of a miliariform type, with greater profusion to the upper lobes, also present in the visceral pleura, bilaterally. Histological examination showed aggregates of pigment-laden macrophages forming perivascular macules or arranged in a radial pattern around a core of sclerohyalinosis. Scanning Electron Microscopy and Energy Dispersive Spectrometry revealed several mineral particles, typically characterized by the presence of crystalline silica and metal aggregates. The environmental concentrations of total dust and its respirable fraction were all lower than the relative TLV-TWA—ACGIH, yet not negligible.ConclusionsThe above findings and a multidisciplinary assessment led to the diagnosis of mixed dust pneumoconiosis s/q with 2/2 profusion of occupational origin. This diagnosis in a dental technician was supported for the first time in literature by environmental exposure analysis.

The Multiple States of Environmental DNA and What Is Known about Their Persistence in Aquatic Environments.

Increased use of environmental DNA (eDNA) analysis for indirect species detection has spurred the need to understand eDNA persistence in the environment. Understanding the persistence of eDNA is complex because it exists in a mixture of different states (e.g., dissolved, particle adsorbed, intracellular, and intraorganellar), and each state is expected to have a specific decay rate that depends on environmental parameters. Thus, improving knowledge about eDNA conversion rates between states and the reactions that degrade eDNA in different states is needed. Here, we focus on eukaryotic extraorganismal eDNA, outline how water chemistry and suspended mineral particles likely affect conversion among each eDNA state, and indicate how environmental parameters affect persistence of states in the water column. On the basis of deducing these controlling parameters, we synthesized the eDNA literature to assess whether we could already derive a general understanding of eDNA states persisting in the environment. However, we found that these parameters are often not being measured or reported when measured, and in many cases very few experimental data exist from which to draw conclusions. Therefore, further study of how environmental parameters affect eDNA state conversion and eDNA decay in aquatic environments is needed. We recommend analytic controls that can be used during the processing of water to assess potential losses of different eDNA states if all were present in a water sample, and we outline future experimental work that would help determine the dominant eDNA states in water.

Experimental investigations on the vertical distribution and properties of oil-mineral aggregates (OMAs) formed by different clay minerals

After oil spills, the floating oil may interact with suspended minerals to form the oil-mineral aggregates (OMAs) in turbulent environments. In this work, a flume was used in conjunction with a settling device to investigate the vertical distribution and properties of OMAs formed by different clay minerals. The density and size of OMAs depend on the density and surface properties of the constituent particles, which also affect the vertical distribution of dispersed oil. Density of oil-montmorillonite aggregates increased from 1165 to 1897 kg/m3 within 6 h test. Among the four minerals, montmorillonite displayed the highest affinity with dispersed oil and the most significant modification of oil-water interfacial tension. Oil dispersion efficiency was significantly greater and reached 39.3% in the presence of montmorillonite at 300 mg/L compared with the control group (17.6%). Particle concentration is the most important factor for the capture of oil and participation of particles during the OMA formation, while the zeta potential and hydrophobicity have nonsignificant effect on the two processes. Cation exchange capacity has a moderate effect on the sunken oil formation, which is also the second main factor governing the particle participation. Particle size plays a second leading role in governing the sunken oil formation but with a minor contribution of the particle participation.

Методический подход к характеристике загрязнения природных водоемов по спутниковым данным с учетом агрегации тонкодисперсных отходов переработки минерального сырья

The level of the environmental impact of the mining industry specifies the urgency of ecological management of the natural resources based on the satellite monitoring data. The high content of the suspended mineral particles in the industrial waters and the requirement to reduce their access to the natural water reservoirs determine the need to characterize the mininginduced pollution that can be carried out correctly with due account of the aggregate stability of dispersions. In spite of the theoretical concepts, prediction of the particles aggregation is limited by a lack of data on their interaction parameters. In order to parametrize the interactions in the mineral-water-mineral system it is proposed to use experimental data on aggregation of finely dispersed particles, obtained by the laser diffraction method in the equilibrium conditions. For this purpose the procedure of the experimental appraisal of the effective Hamaker constants has been elaborated using ores of developed deposits of the Kola mining complex as an example. The authors have studied the conditions of the surface layer of natural water reservoirs in the most industrially developed central part of the Murmansk region and defined characteristics of pollution with finely dispersed by-products of the mineral raw material treatment, according to the satellite observation data of the spatial distribution of the normalized difference turbidity index. The authors have established that the least propagation of the pollution into the natural water reservoirs is observed in the case of the apatite-nepheline ores processing by-products, which is explained by the effective aggregation of the finely dispersed nepheline particles. The proposed approach to apply data on mineral particles aggregation for interpretation of the satellite observations does not require carrying out in-situ observations and makes it possible to identify the mining-induced pollution of natural water reservoirs in industrial territories using suspended particles.

Organic Matter Composition of Biomineral Flocs and Its Influence on Suspended Particulate Matter Dynamics Along a Nearshore to Offshore Transect

AbstractThe seasonal variation in concentration of transparent exopolymer particles (TEPs), particulate organic carbon (POC) and particulate organic nitrogen (PON) were investigated together with floc size and the concentration of suspended particulate matter (SPM) along the cross‐shore gradient, from the high turbid nearshore toward the low‐turbid offshore waters in the Southern Bight of the North Sea. Our data demonstrate that biophysical flocculation cannot be explained by these heterogeneous parameters, but requires a distinction between a more reactive labile (“fresh”) and a less reactive refractory (“mineral‐associated”) fraction. Based on all data, we separated the labile and mineral‐associated POC, PON, and TEP using a semi‐empirical model approach. The model's estimates of fresh and mineral‐associated organic matter (OM) show that great parts of the POC, PON, and TEP are associated with suspended minerals, which are present in the water column throughout the year, whereas the occurrence of fresh TEP, POC, and PON is restricted to spring and summer months. In spite of a constantly high abundance of total TEP throughout the entire year, it is its fresh fraction that promotes the formation of larger and faster sinking biomineral flocs, thereby contributing to reducing the SPM concentration in the water column over spring and summer. Our results show that the different components of the SPM, such as minerals, extracellular OM and living organisms, form an integrated dynamic system with direct interactions and feedback controls.

Investigation of machining and modified surface features of 316L steel through novel hybrid of HA/CNT added-EDM process

Hydroxyapatite powder (HAp) mixed-EDM process causes surface defects including a high roughness, crack and a thick recast layer attributing a low wettability and amorphous alloys as well as a low material erosion rate (MER) while processing the metallic biomaterials. To mitigate these occurrences, many measures have been conducted. This research aims to investigate the feasibility of hybrid HA and carbon nanotubes (CNT) powders mixed EDM process for processing 316L steel. This study also aims to explore the impacts of CNT and the associated variables on machining and surface characteristics of 316L steel. To ameliorate the machining and surface responses, a high electrically and thermally conductive CNT particles have been added in the HAp suspended mineral oil. To address the set objectives, several characterizations techniques including profilometer, goniometer, energy dispersive X-ray (EDX), X-ray diffraction (XRD), and scanning-electron microscope (SEM) have been carried out. In this study, the multiple additives (HAp and CNT) mixed-EDM process has been successfully introduced. Addition of the CNT in the HAp mixed mineral oil improves MER to 26.47 mg/min and declines SR to 3.16 μm. A thin uniform recast layer of 12.4 μm attributing cracks free surface and a high hydrophilic in nature having contact angle of 35° has been obtained in this study. Elemental composition analysis reveals a high content of Ca, P, O and C in the recast layer formed. The oxides, carbides, and CNT reinforced Ca-P based oxides with both crystalline and amorphous phases have been achieved. In this research work, a novel and effective method for processing the biomedical devices made of 316L steel has been proposed.

Influence of different mineral particles in lubricating grease on the fretting behavior between steel wires under different contact forms

The suspended mineral particles in the mine aggravate the wear of hoisting wire rope and seriously threaten the mine safety. In order to explore the effect of different mineral particles on the fretting behavior between steel wires, the wear test of steel wires under different contact forms was performed by a homemade tester. Results show that the coefficient of friction between steel wires decreases with increasing the concentrations of mineral particles (coal particles and ore particles). The wear coefficient of steel wire decreases with the increase of the coal particle concentration, while for the grease mixed with ore particles, the wear coefficient presents the opposite change rule. Compared with the original grease and the grease mixed with coal particles, the wear scars of steel wire under the grease mixed with ore particles condition show more serious furrows, micro cracks and pits. The wear mechanisms of steel wire lubricated by the grease mixed with different mineral particles are abrasive wear, adhesive wear and fatigue wear.

Extracellular Electron Transfer of Electrochemically Active Bacteria Community Promoted by Semiconducting Minerals with Photo-Response in Marine Euphotic Zone

Based on the most active hydrosphere on the earth, the interplay between adjacent semiconducting minerals and electrochemically active microorganisms was scientifically researched in the marine euphotic zone of the Yellow Sea, China. Fe and Ti were found in suspended minerals by ICP-MS and EDS, probing the element composition of suspended minerals from macro to micro. Moreover, SR-XRD and Raman indicated that semiconducting minerals of iron and titanium metal oxide in situ such as anatase, rutile, brookite, and goethite consisted in suspended minerals, notably, which retained prominent photo-response property and distinct photoelectric catalytic potential under visible light. 16S rRNA gene systematically emerged that electrochemically active microorganisms, such as Pseudomonas and Paraclostridium, were pivotal in the solution and preponderant on the electrode respectively after a period of cultivation. Whereupon a dual-chamber reactor was established to probe into the mechanism of redox reaction and electron transfer process between microorganisms and suspended minerals. Importantly, compared with a graphite electrode, the maximum power density of the reaction was 2.78 times with the increase of suspended minerals as the electron acceptor under dark conditions, as well as 236.53% promotion with visible light. Experiments gave an index that semiconducting minerals could interact with electroactive microorganisms, effectively promoting the process of extracellular electron transfer in the euphotic zone, which will make a foundation for further research on electron energy transfer based on the interactions of semiconducting minerals and electrochemically active microorganisms, as well as the regulation mechanism of elements cycling.