Membrane Surface Research Articles

Adsorption and transport of acid dye through polymer inclusion membrane with Aliquat 336 and TBP

Colour is typically the initial pollutant identified in wastewater. Membrane separation represents a novel approach to separation processes, with expectations of supplanting many traditional separation systems. The aim of this study is to investigate polymer inclusion membranes (PIMs) consisting of tri octyl methyl ammonium chloride as the carrier, tributylphosphate as the modifier, poly-vinyl chloride as the base polymer and 2-Nitro phenyl pentyl ether as the plasticizer for removing an acid dye (Red Erionyl A-3G) from aqueous solution. The dye adsorption on the membrane surface and its transition to the stripping phase was achieved by placing the membrane between two glass cells. Changing the stripping solution ensured both adsorption on the membrane surface and the transfer of all the dye to the stripping stage. Using a mixture of 0.8 M salicylic acid and 0.8 M NaOH, along with stirring at 1000 rpm during the stripping phase, extraction efficiency reached 98% in the feed phase and 53% in the stripping phase. When 1 M NaOH solution was employed as the stripping solution, the membrane absorbed all the dye within 10 minutes, but there was no transition to the stripping phase. The membrane has a durability of 2 days.Graphical abstract

Photo-responsive anti-fouling polyzwitterionic brushes: a mesoscopic simulation.

The antifouling effects of a toothbrush-shaped photo-responsive polyzwitterionic membrane were studied via dissipative particle dynamics simulations in this work. The results reveal that the membrane modified by spiropyran methacrylate brushes displays photo-switchable and antifouling capability due to the photo-induced ring-opening reaction. Namely, surface morphology and hydrophilicity change in response to visible or UV light irradiation, which can be observed visually by protein adsorption and desorption. Further study indicates that: (1) brush-modification density can influence the structure and properties of the membrane. With low modification density, systems cannot establish an intact selective layer, which hinders the antifouling ability; as the modification density increases, the intact selective layer can be formed, which is conducive to the expression of photo-responsiveness and antifouling capability. (2) Factors of toothbrush-hair length and grafting ratio can influence the establishment of a light-responsive surface: as the grafting ratio and toothbrush-hair length increase, the light-responsive surface is gradually formed, meanwhile, the antifouling ability can be continuously reinforced under UV light irradiation. (3) As the brushes switch into a zwitterionic merocyanine state under UV exposure, the selective layer swelling becomes stronger than that with a hydrophobic spiropyran state under visible exposure. This is owing to the enhanced interaction between zwitterionic brushes and water, which is the root of the antifouling effect. The present work is expected to provide some guidelines for the design and development of novel antifouling membrane surfaces.

Small and Large Extracellular Vesicles of Porcine Seminal Plasma Differ in Lipid Profile

Seminal plasma contains a heterogeneous population of extracellular vesicles (sEVs) that remains poorly characterized. This study aimed to characterize the lipidomic profile of two subsets of differently sized sEVs, small (S-) and large (L-), isolated from porcine seminal plasma by size-exclusion chromatography and characterized by an orthogonal approach. High-performance liquid chromatography–high-resolution mass spectrometry was used for lipidomic analysis. A total of 157 lipid species from 14 lipid classes of 4 major categories (sphingolipids, glycerophospholipids, glycerolipids, and sterols) were identified. Qualitative differences were limited to two cholesteryl ester species present only in S-sEVs. L-sEVs had higher levels of all quantified lipid classes due to their larger membrane surface area. The distribution pattern was different, especially for sphingomyelins (more in S-sEVs) and ceramides (more in L-sEVs). In conclusion, this study reveals differences in the lipidomic profile of two subsets of porcine sEVs, suggesting that they differ in biogenesis and functionality.

Tailor-Made Heterocharged Covalent Organic Framework Membrane for Efficient Ion Separation.

Pore size sieving, Donnan exclusion, and their combined effects seriously affect ion separation of membrane processes. However, traditional polymer-based membranes face some challenges in precisely controlling both charge distribution and pore size on the membrane surface, which hinders the ion separation performance, such as heavy metal ion removal. Herein, the heterocharged covalent organic framework (COF) membrane is reported by assembling two kinds of ionic COF nanosheets with opposite charges and different pore sizes. By manipulating the stacking quantity and sequence of two kinds of nanosheets, the impact of membrane surface charge and pore size on the separation performance of monovalent and multivalent ions is investigated. For the separation of anions, the effect of pore size sieving is dominant, while for the separation of cations, the effect of Donnan exclusion is dominant. The heterocharged TpEBr/TpPa-SO3H membrane with a positively charged upper layer and a negatively charged bottom layer exhibits excellent rejection of multivalent anions and cations (Ni2+, Cd2+, Cr2+, CrO4 2-, SeO3 2-, etc). The strategy provides not only high-performance COF membranes for ion separation but also an inspiration for the engineering of heterocharged membranes.

Effective Application of Biocompatible Magnetite Nanoparticles in the Treatment of Multiple Sclerosis: Results of a Clinical Study

Multiple sclerosis (MS) is a serious neurological disorder due to its widespread prevalence, chronic nature, frequent progression to disability, and tendency to affect young people. The pathogenesis of MS is based on the immunopathogenesis hypothesis. Biocompatible magnetite nanoparticles, which exhibit selective sorption activity towards cell membrane surface proteins, circulating immune com-plexes, lymphocytotoxic antibodies, and the complement system, as well as enhance phagocytic ac-tivity and the completion index of leukocyte phagocytosis, can be effectively used for immunocor-rection. The main goal of the study is to slow the progression of MS, improve the neurological status and overall condition of the patient, and reduce the dynamics of the spread of demyelinating lesions in the brain. Materials and methods: A patient diagnosed with multiple sclerosis, secondary progres-sive type, cerebrospinal form, at the clinical aggravation stage was included in the study. Neurologi-cal status and disability were assessed using the EDSS scale, and brain MRI with contrast enhance-ment was performed. The nanodevice Micromage-B was administered orally as an immunosorbent and immunomodulator. The regimen and dosage of Micromage-B were personalized. Assessments of general condition and neurological status were conducted every 7 days for 6 months, with contrast-enhanced brain MRI performed in the 5th month. Results: The use of Micromage-B in MS treatment led to an objective improvement in neurological status, with reduced stiffness and fatigue in the lower extremities. Gait and coordination improved, hand tremors decreased, depression and concen-tration disorders subsided, appetite was restored, and speech improved. Throughout the treatment period, positive dynamics in the normalization of neurological status were observed. After 6 months, the total score on the EDSS scale decreased from 210 to 45. The most significant improvements were observed in the evaluation of the pyramidal system and coordination, with the EDSS Disability Scale score decreasing from 6.0 to 5.0. For the first time, contrast-enhanced brain MRI showed a reduction in the number of new demyelination foci by the 4th month of Micromage-B administra-tion. The positive changes in neurological status correlated with the MRI results. The recovery of central nervous system activity in MS is likely not only due to the immunosuppressive properties of magnetite nanoparticles but also due to the activation of remyelination mechanisms and oligoden-drocyte differentiation through enzymatic methylation. Conclusion: The use of biocompatible nanodevices in the complex treatment of MS is promising. Further improvement and study of the regimen and method of using biocompatible magnetite nanoparticles to enhance MS treatment effec-tiveness are required.

Endoplasmic reticulum stress regulates apoptosis and chemotherapeutic via enhancing TNFRSF10B recycling to the cell membrane in triple-negative breast cancer.

Triple-negative breast cancer (TNBC) is the most common malignant tumor in China. The expression and cell surface levels of TNF receptor superfamily member 10B (TNFRSF10B) are associated with apoptosis and chemotherapy. However, the precise molecular mechanisms that govern the regulation of TNFRSF10B remain unclear. RNA-Seq data related to TNBC chemotherapy resistance were acquired from the GEO database. The mRNA and protein levels of TNFRSF10B were detected using RT-PCR and Western blotting, respectively. Cell Counting Kit-8 (CCK-8) and colony formation assays were used to detect cell proliferation. Annexin V/7-AAD staining was used to evaluate apoptosis. The cell membrane TNFRSF10B was analyzed by Western blotting and immunofluorescence. Inducers and inhibitors of endoplasmic reticulum stress (ERS) were used to assess the effect of ERS on TNFRSF10B localization. TNFRSF10B expression was downregulated in TNBC and was associated with prognosis. TNFRSF10B overexpression inhibits the growth of TNBC both in vivo and in vitro and can partially counteract chemotherapy resistance. ERS activation in TNBC promotes the expression of TNFRSF10B, leading to its enrichment on the cell membrane surface, thereby activating the apoptotic pathways. ERS regulates the expression and subcellular localization of TNFRSF10B in TNBC cells. They synergistically affect anti-apoptosis and chemotherapy resistance in TNBC cells.

U(VI) mitigation via forward osmosis: elucidation of retention mechanisms and co-ion effects

Uranium (U) is a chemical and radioactive toxic contaminant affecting many groundwater systems. The focus of this study was to evaluate the suitability of forward osmosis (FO) for uranium rejection from contaminated groundwater under field-relevant conditions. Laboratory experiments with aqueous solution containing uranium were performed with FO membrane to understand the uranium rejection mechanism under varied pH, draw solution concentration, and presence of co-ions. Further, experiments were performed with U-contaminated field groundwater. Results of the hydrogeochemcial modelling using PHREEQC indicated that the rejection mechanism of uranium was highly dependent on aqueous speciation. Uranium rejection was maximum at alkaline pH with ca. 99% rejection due to charge-based interactions between membrane and dominant uranyl complexes. The results of the co-ion study indicated that nitrate and phosphate ions decrease uranium rejection. Whereas, bicarbonates, calcium, and magnesium ions concentrated uranium in feed solution. Further, the uranium adsorption onto the membrane surface primarily depended on pH of the aqueous solution with maximum adsorption at pH 5.5. Our results show that the World Health Organization’s drinking water guideline value of 30 μgL−1 for U could be achieved via FO process in field groundwater containing low dissolved solids.

An Innovative Surface Modification Technique for Antifouling Polyamide Nanofiltration Membranes.

In this study, we developed a novel surface coating technique to modify the surface chemistry of thin film composite (TFC) nanofiltration (NF) membranes, aiming to mitigate organic fouling while maintaining the membrane's permselectivity. We formed a spot-like polyester (PE) coating on top of a polyamide (PA) TFC membrane using mist-based interfacial polymerization. This process involved exposing the membrane surface to tiny droplets carrying different concentrations of sulfonated kraft lignin (SKL, 3, 5, and 7 wt %) and trimesoyl chloride (TMC, 0.2 wt %). The main advantages of this surface coating technique are minimal solvent consumption (less than 0.05 mL/cm2) and precise control over interfacial polymerization. Zeta potential measurements of the coated membranes exhibited enhancements in negative charge compared to the control membrane. This enhancement is attributed to the unreacted carboxyl functional groups of the SKL and TMC monomers, as well as the presence of sulfonate groups (SO3) in the structure of SKL. AFM results showed a notable decrease in membrane surface roughness after polyester coating due to the slower diffusion of SKL to the interface and a milder reaction with TMC. In terms of fouling resistance, the membrane coated with a polyester composed of 7 wt % SKL showed a 90% flux recovery ratio (FRR) during Bovine Serum Albumin (BSA) filtration, showing a 15% improvement compared to the control membrane (PA). PE-coated membranes provided stable separation performance over 40 h of filtration. The sodium chloride rejection and water flux displayed minimal variations, indicating the robustness of the coating layer. The final section of the presented study focuses on assessing the feasibility of scaling up and the cost-effectiveness of the proposed technique. The demonstrated ease of scalability and a notable reduction in chemical consumption establish this method as a viable, environmentally friendly, and sustainable solution for surface modification.

Development and life cycle assessment (LCA) of super-oleophobic (under water) and super-hydrophilic (in-air) mesh membrane for oily water treatment

This paper reports the fabrication, characterization, and environmental impact analysis of a super-oleophobic (under water) and super-hydrophilic mesh membrane for oily water treatment. In order to prepare mesh membrane, Titania nanoparticles (NPs) were spray coated on mesh stainless steel followed by calcination at 500 °C. After that, the Titania-coated mesh membrane was characterized using contact angle goniometry (CA), XRD, FE-SEM, EDX and elemental mapping. The FE-SEM, EDX, elemental mapping and XRD results confirmed that the Titania NPs were successfully coated on the surface of mesh membrane. CA results demonstrated that the prepared mesh membrane is super-hydrophilic and super-oleo phobic under water conditions, making it suitable for oil/water separation. Subsequently, life cycle assessment (LCA) was performed to determine the environmental impacts of Titania NPs-coated mesh membrane fabrication process. LCA results indicate that electricity and nitrogen contributed the most toward the eighteen environmental impact categories considered for this study.

Construction of PEO@g-C3N4 supported ionic liquid membrane with interactive network structure for enhanced carbon capture efficiency

Polyethylene oxide (PEO) shows a high CO2-philic due to its dipolar-quadrupolar interaction with CO2 molecules. As a result, it is an excellent candidate for gas separation applications, yet it faces problems such as crystallization and low permeance. Herein, we show a versatile strategy to enhance gas permeation fluxes, which is mainly achieved by hindering the crystallization of PEO and the stacking of nanosheets. Specifically, graphite-like phase carbon nitride (g-C3N4) nanosheets are introduced and interaction networks (PGCN) are constructed by taking full advantage of the dipole-level quadrupole moment interactions between the ether-oxygen groups contained in PEO and CO2. In order to compensate the membrane surface defects for enhancing gas selectivity, we used the suspension coating method to create a PEO@g-C3N4 supported ionic liquid membrane (PGCN/ILX SILM) by coating IL on the surface of membrane. The results show that, when the IL concentration is 30 wt%, the PGCN/IL30 % membrane separates CO2/N2 with a CO2 permeance of 1396 GPU and an optimal selectivity of 58. While overcoming the “Trade-off” effect, it has demonstrated good thermal stability and long-term stable operation for 72 h. The development of this work will generate solutions for overcoming PEO crystallization and achieving efficient CO2 capture.

Effectiveness of cloth media filters on mitigating membrane fouling in anaerobic filter membrane bioreactors

Membrane fouling is a persistent challenge that has impeded the broader application of anaerobic membrane bioreactors (AnMBRs). To mitigate membrane fouling, between the outlet of the UASB anaerobic bioreactor and the PVDF membrane to form the anaerobic filter membrane bioreactor (AnFMBR) system. Through comprehensive experiments, the optimal pore size for cloth filters was determined to be 50 μm. A comprehensive assessment over 140 days of operation shows that the novel AnFMBR had significantly greater resistance to membrane pollution than the traditional AnMBR. The AnFMBR system membrane tank exhibited lower mixed liquor suspended solid and mixed liquor volatile suspended solid concentrations, smaller sludge particle sizes, increased hydrophilicity of sludge flocs, and optimized microbial community distribution compared to those of conventional AnMBRs. The total solids foulant accumulation rate in the AnMBR was 5.1 g/m2/day, while in the AnFMBR, the rate was 2.4 g/m2/day, marking a 53.7 % decrease in fouling rate for the AnFMBR compared with the AnMBR. This decrease indicates that integrating the filtration assembly significantly lowered the rate of solid foulant accumulation on the membrane surface, primarily by controlling the buildup of solid foulants in the cake layer, thereby alleviating membrane fouling. AnFMBR compared to AnMBR, the membrane fouling rate halved, effectively doubled the interval between membrane cleaning from seven days, as observed in the AnMBR system, to fourteen days. These findings underscore the potential of integrating cloth media filters into AnMBRs to improve operational efficiency, economic viability, and sustainability.

Incorporation of composite metal-PVP derived carbon membranes for the percrystallisation of salt water

In this research using supported metal‑carbon membranes in a membrane percrystallisation application, we investigated the influence of metal ions on the formation of carbon during carbon membrane synthesis by combining polyvinylpyrrolidone (PVP) with various metal compounds, including zinc, potassium, barium, sodium, magnesium, calcium, and strontium, through calcination at 700 °C in a nitrogen atmosphere for the first time. These carbon membranes were then subjected to continuous percrystallisation experiments to produce dry salt crystals from salt solutions. The feed solution (3.5, 10, 20 wt% of salt) were used at 30, 50, and 70 °C for the performance evaluation. Intriguingly, the addition of metal elements to the PVP solution resulted in an enhancement in the total pore volume and surface area of the resulting carbon membranes. The PVP-Zn precursor exhibited the highest increase with a maximum improvement of 99 fold. Moreover, when compared to the PVP membranes alone, the composite membranes also exhibited higher fluxes. Among the tested composite carbon membranes, PVP-Ca, PVP-Zn, and PVP-Mg demonstrated the highest flux values, reaching an impressive 55 kg.m−2.h−1. Additionally, these membranes exhibited self-elimination, where salt was effectively removed from the membrane surface during percrystallisation testing. Thus, these membranes have the potential to be employed in desalination applications.

Integration of CaO2/Fe2+ and ultrafiltration acts as multiple-workfunctions pretreatment for seawater desalination during harmful algal blooms

This study employed calcium peroxide/ferrous iron (CaO2/Fe2+) as an innovative pretreatment strategy for seawater reverse osmosis (SWRO) operation during harmful algae blooms (HABs). CaO2/Fe2+ showed improved coagulation performance compared to conventional coagulation (Fe3+ coagulant). The dynamic dominance of foulants between micro-particles and algal organic matters (AOMs), due to the different dosages of CaO2/Fe2+, was found to be crucial in reducing ultrafiltration (UF) fouling. As a result, the optimal dosage of 0.05 mM/0.1 mM of CaO2/Fe2+ achieved a higher reduction of 71.6 % of modified fouling index (MFI) compared to conventional coagulation (38.1 % via 0.1 mM Fe3+). Specifically, CaO2/Fe2+ demonstrated a greater capacity to remove micro-particles across size ranges of 1–5 μm and various AOMs (i.e., biopolymer and humics) in algae-laden seawater compared to conventional coagulation. This resulted in reduced flux decline and less accumulation of algal cells, proteinaceous substances and humics on membrane surfaces, which were validated through Optical-Photothermal Infrared Spectromicroscopy (O-PTIR) with sub-micron resolution. Additionally, CaO2/Fe2+ reduced dissolved Fe3+ in UF permeate, and generated combined chlorine simultaneously with disinfection effects on marine algae (evidenced by O-PTIR and Raman spectroscopy). Thus, it would reduce fouling of subsequent SWRO membranes. Overall, CaO2/Fe2+ presents a multiple-workfunctions pretreatment method for HAB mitigation in seawater desalination plants.

Applications of Titanium Dioxide (TiO2) Nanoparticles in Photocatalysis

Titanium dioxide nanoparticles (TiO2 NPs) are conspicuously preferred as photocatalyst among the transition metal oxide nanoparticles. It exhibited in three polymorphisms of steady state rutile phase while brookite and anatase sustaining in metastable phase. The mixed phases of anatase phase and rarely found brookite phase mostly preferred for the photodegradation applications. The economically affordable along with nontoxic nature on top of excellent opto-electronics and catalytic properties of TiO2 NPs are eminently favorable for the photocatalytic degradation of chemically complex structured numerous organic and inorganic dyes, phenol and phenol-based derivatives, passive microplastics as well as suspended matters, non-biodegradable cytostatic drugs, acetaminophen, pharmaceutical organic waste compounds in addition to water pollutants. The photocatalytic capability of these NPs enhanced by upgrading the structural and morphological nature by opting different synthesis techniques as well preparing the nanocomposites of TiO2 incorporation with other metals. The hydrothermally prepared polymeric membranes of polyvinylidene with TiO2 NPs effectively (more than 90%) removed 17 α–ethinylestradiol from the contaminated water compared to Diclofenac under Uv irradiation. As it fronting the issue of electrostatic repulsion to all other membranes surface. The grafted membrane recorded highest degradation efficiency of 95.4% and best reusability of 90% saturated at fifth recycle for Methylene Blue azo dye compared with blending and dip coating membranes. The TiO2 modified ultrafiltration membranes of Polyvinylidene Fluoride with Dopamine illustrated the 92.6% photocatalytic degradation of Sulfadiazine which is most hazardous and highly resistant to biodegradation. 100% degradation of phenol derivative by TiO2 NPs hybrid polymeric films in visible light irradiation. The degradation efficiency of heterogenous photocatalyst Carbon–TiO2 contained anatase and brookite phased for Methylene Blue dye was 100% while for Rhodamine–B higher than 99% in solar and more than 78% in LED light irradiation. The recent trends for improvisation of photocatalytic ability of TiO2 NPs to enhance the quality of water and hence the mankind are elaborated.

Hierarchical biocatalytic membranes embedded with trypsin–inorganic hybrid nanoflowers for effective β-lactoglobulin hydrolysis

β-lactoglobulin (β-LG) is a significant allergen in milk. Enzymatic hydrolysis of β-LG produces peptides with low allergenicity and improved functionality. The biocatalytic membranes combine enzyme function and membrane separation in one step, but is still challenging for proteolysis. Herein, the biocatalytic membranes embedded with trypsin-inorganic hybrid nanoflowers are developed by a facile and green method for β-LG hydrolysis. Ethylene vinyl alcohol copolymer (EVAL) nanofibers are fabricated as 3D scaffolding on the membrane surface and trypsin-copper phosphate nanoflowers are in-situ grown in the porous structure of membranes. The nanoflowers are uniformly entrapped in the EVAL nanofiber layer and preferentially grow in the EVAL nanofibers layer, leading to the hierarchical structure of membranes. The trypsin loading of the nanoflowers membrane is approximate to 282.1µg/cm2. Lower Michaelis-Menten constants Km prove the better affinity of Cu3(PO4)2-TR nanoflower membrane with substrates during filtration than that in static mode, even than free trypsin. The hierarchical structure of the membranes ensures both the enhanced trypsin-substrate contacts and low mass transfer resistance during the β-LG filtration. This work not only presents a novel concept of enzyme immobilized biocatalytic membranes, but also offers a sustainable solution for high-performance proteolysis.

Controlling of irreversible fouling and mechanism in a hybrid ceramic membrane bioreactor (CMBR)-reverse osmosis (RO) process for textile wastewater reclamation

In this study, the fouling propensity of a hybrid ceramic membrane bioreactor (CMBR)-reverse osmosis (RO) process was investigated over a prolonged period using real textile wastewater effluent. Additionally, the effectiveness of in-situ ozonation for fouling mitigation was investigated. The results revealed that the CMBR-RO system achieved approximately 99.8 % removal of chemical oxygen demand and 97.4 % removal of total nitrogen. Despite this, soluble extracellular polymeric substances, particularly biopolymers and humics-like substances, remained in the system, resulting in irreversible fouling on the ultrafiltration (UF) membrane. The implementation of in-situ ozonation notably reduced ceramic membrane fouling by enhancing the filterability of larger macromolecules and eliminating inorganic/organic foulants from the membrane surface. Multiple modified fouling indexes were also utilized to evaluate the fouling potential of the RO feed water through size fractionation. It is worth noting that ozonation could pose a potential risk for subsequent RO membrane fouling due to the formation of low molecular weight neutrals, acids, and calcium- or silica- related inorganic-organic complexes. Overall, the integrated CMBR-RO system with in-situ ozonation exhibited excellent performance in producing clean water, achieving nearly 100 % removal of 20 Aromatic Amines. These findings underscore the viability of the CMBR-RO system as a practical and sustainable choice for the reclamation of textile wastewater.

Choline chloride modification of nanofiltration membranes for improving heavy metal ions separation in wastewater

The growing concern over heavy metal ion contamination in industrial wastewater, posing a significant threat to global public health, has led to a heightened interest in devising efficient removal methods. Nanofiltration, while promising, faces a substantial challenge in simultaneously achieving a high rejection of heavy metal cations and maintaining an elevated water permeance. In response, this study utilizes a simple approach by employing choline chloride with a quaternary ammonium group to modify the surface of PEI-TMC membrane, leading to the design of a high-performance PEI-TMC-CC membrane. The choline chloride modification optimized the surface morphology, hydrophilicity, roughness, and combined the Donnan exclusion effect as well as sieving effect, enabling the PEI-TMC-CC membrane to achieve an exceptional rejection of heavy metal ions while retaining a great water permeance. An impressive water permeance 10.0 L·m−2·h−1·bar−1 was performed by the PEI-TMC-CC membrane, nearly three times that of traditional PEI-TMC membranes. Concurrently, the PEI-TMC-CC membrane demonstrated an impressive rejection of heavy metals Cd2+, Pb2+, Ni2+, Zn2+, and Cu2+, reaching rejections of 98.3%, 95.9%, 98.1%, 98.5% and 99.1%, respectively. Moreover, density functional theory (DFT) calculations confirmed the improved hydrophilicity of choline chloride molecules, aligning with experimental results. The modification of traditional nanofiltration membranes using cost-effective, hydrophilic, positively charged chemicals not only leads to significant performance improvements but also holds the potential to advance the development of positively charged nanofiltration membranes tailored for the removing of heavy metals cations from wastewater. This approach demonstrates promising prospects for industrial applications and further development.

Comparison of UV/PS and VUV/PS as ultrafiltration pretreatment: Performance, mechanisms, DBPs formation and toxicity assessment

Ultrafiltration (UF) is widely used in drinking water plants, nevertheless, it still encounters challenges stemming from inevitable membrane fouling caused by natural organic matter (NOM). Herein, this work applied VUV/PS as UF membrane pretreatment and used UV/PS for comparison. VUV/PS system exhibited superior ability in removing NOM compared to UV/PS system. HO and SO4− played crucial roles in the degradation. [SO4−]ss was notably higher than [HO]ss in the systems, yet HO was of greater significance. [HO]ss and [SO4−]ss in the VUV/PS process were remarkably higher than those in the UV/PS process, due to the function of 185 nm photons. VUV/PS pretreatment basically recovered flux and effectively reduced fouling resistance, with better performance than UV/PS. Fouling mechanism was dominated by multiple mechanisms after UV/PS pretreatment, whereas it was transformed into pore blockage after VUV/PS pretreatment. Moreover, the UF effluent quality after VUV/PS pretreatment outperformed that of UV/PS but fell short of that without pretreatment, possibly due to the generation of abundant low MW substances under the action of HO and SO4−. After chlorine disinfection, UV/PS and VUV/PS pretreatments increased the DBPs production and cytotoxicity. Specifically, oxidant PS affected the membrane surface morphology and fouling behaviors, and had no obvious effect on interception performance and mechanical properties. In actual water treatment, VUV/PS and UV/PS pretreatments exhibited excellent performance in alleviating membrane fouling, improving water quality, and reducing DBPs formation and acute toxicity.

Alleviation of RO Membrane Fouling in Wastewater Reclamation Plants Using an Enhanced Acid-Base Chemical Cleaning Method

Membrane fouling has always been a critical constraint in the operation of the reverse osmosis (RO) process, and chemical cleaning is essential for mitigating membrane fouling and ensuring smooth operation of the membrane system. This paper presents an optimized chemical cleaning method for efficient cleaning of RO membranes in full-scale applications. Compared to the regular cleaning method (cleaning with 0.1% NaOH+1% EDTA+0.025% SDBS followed by 0.2% HCl), the optimized cleaning method improves the cleaning efficiency by adding sodium chloride to the alkaline cleaning solution and citric acid to the acid cleaning solution. Notably, the membrane flux recovery rate with the optimized cleaning method is 45.74%, and it improves the cleaning efficiency by 1.65 times compared to the regular cleaning method. Additionally, the optimized cleaning method removes 30.46% of the total foulants (organic and inorganic), which is 2.11 times higher than the regular cleaning method. The removal of inorganic ions such as Fe, Ca, and Mg is significantly improved with the optimized cleaning method. For organic matter removal, the optimized cleaning method effectively removes more polysaccharides, proteins, and microbial metabolites by disrupting the complex structure of organic matter. Furthermore, it also changes the microbial community structure on the RO membrane surface by eliminating microorganisms that cannot withstand strong acids, bases, and high salt environments. However, Mycobacterium can adapt to these harsh conditions and shows a relative abundance of up to 84.13% after cleaning. Overall, our results provide a new chemical cleaning method for RO membranes in full-scale applications. This method effectively removes membrane foulants and enhances the understanding of the removal characteristics of foulants on RO membrane surfaces by chemical cleaning.

Investigating Dialysis Membrane Surface Charge and Hydrophobicity Effects on Fibrinogen Adsorption Using Synchrotron Radiation Micro-Computed Tomography (SR-CT)

Investigating Dialysis Membrane Surface Charge and Hydrophobicity Effects on Fibrinogen Adsorption Using Synchrotron Radiation Micro-Computed Tomography (SR-CT)