Surface Plasmon Resonance Sensor Research Articles

Fabrication of an Antifouling Surface Plasmon Resonance Sensor with Stratified Zwitterionic Peptides for Highly Efficient Detection of Peanut Allergens in Biscuits.

Peanut allergen monitoring is currently an effective strategy to avoid allergic diseases, while food matrix interference is a critical challenge during detection. Here, we developed an antifouling surface plasmon resonance sensor (SPR) with stratified zwitterionic peptides, which provides both excellent antifouling and sensing properties. The antifouling performance was measured by the SPR, which showed that stratified peptide coatings showed much better protein resistance, reaching ultralow adsorption levels (<5 ng/cm2). Atomic force microscopy was used to further analyze the antifouling mechanism from a mechanical perspective, which demonstrated lower adsorption forces on hybrid peptide coatings, confirming the better antifouling performance of stratified surfaces. Moreover, the recognition of peanut allergens in biscuits was performed using an SPR with high efficiency and appropriate recovery results (98.2-112%), which verified the feasibility of this assay. Therefore, the fabrication of antifouling sensors with stratified zwitterionic peptides provides an efficient strategy for food safety inspection.

Design of Surface Plasmon Resonance (SPR) Sensors for Highly Sensitive Biomolecular Detection in Cancer Diagnostics

Design of Surface Plasmon Resonance (SPR) Sensors for Highly Sensitive Biomolecular Detection in Cancer Diagnostics

D-Shaped PCF With Quasi-Sinusoidal Surface Topography for Dual-Polarization and Enhanced Performance Surface Plasmon Resonance Sensor

D-Shaped PCF With Quasi-Sinusoidal Surface Topography for Dual-Polarization and Enhanced Performance Surface Plasmon Resonance Sensor

Design of a highly sensitive and precise long-range surface plasmon resonance sensor for early detection of malaria

This manuscript presents an innovative Kretschmann configured for Long Range Surface Plasmon Resonance (LRSPR) sensor for malaria detection. It utilizes tungsten diselenide (WSe2) as a bio+molecular recognition element (BRE) layer to attach target analyte. The optimized sensor design demonstrates exceptional performance in detecting different malaria stages (Schizont with refractive index (RI) = 1.371, Trophozoite with RI = 1.381, and Ring with RI = 1.396) at a 633 nm wavelength. In comparison to conventional surface plasmon resonance (CSPR), the LRSPR biosensor exhibits a substantial improvement, a 6.67 to 10 times increase in detection accuracy (DA), an impressive 40 to 86.55 times enhancement in imaging figure of merit (IFOM), and a 6.0 to 8.66 times boost in imaging sensitivity (Simg.) for the sequential detection of different stages of malaria. COMSOL Multiphysics simulations highlight a deeper penetration depth (PD) of 258.71 nm, 276.85 nm, and 373.04 nm for the detection of Schizont, Trophozoite, and Ring stages, respectively.

Ammonia-trapping multilayer polymer urease film amplifier coated surface plasmon resonance sensor for ultra-sensitive urea detection

In this paper, we have developed a new urea signal amplification technology based on a multilayer urease polymer film self-assembly structure for the first time, enabling the realization of ultra-accurate urea optical detection. We demonstrate the effectiveness of this technique based on surface plasmon resonance (SPR) platform. When the urea signal amplifier is combined with SPR sensors, multilayer urease polymer film contacts with urea molecules, the urea molecules are oxidated into NH3 and CO2, causing the pH increase, which weakens the electrostatic interaction between different polymer layers and induces the RI reduction of the multilayer urease film, thereby causing the shift of the SPR spectrum. Experiment results confirm that urea sensitivity has been improved 12-fold, and the limit of detection (LOD) has been optimized to less than 10−3 mmol/L. Furthermore, the anti-interference has been improved 22.8-fold and is kept even the interference signal strength increases by 100 times. Moreover, multilayered urease polymer leads to the increase of urease on the sensor surface, thus expanding the detection range of urea by 3.5 times. This provides a new way to solve the contradiction between high sensitivity and large measurement range of optical fiber biosensor. Importantly, the concept of using enzyme-loaded polymer films for signal amplification can be adapted for the detection of various other biomolecules by replacing the enzyme with a specific recognition element for the target molecule. This opens doors for developing highly sensitive and specific biosensors for diverse applications in healthcare, environmental monitoring, and food safety.

The effect of surface roughness on the performance of 3D printed surface plasmon resonance sensors for refractive index measurements

AbstractIn this study, a polymer-based surface plasmon resonance (SPR) sensor for refractive index measurements was designed and manufactured via inkjet 3D printing; then, it was optically characterized. Next, it was investigated how the surface finish of the 3D printed optical waveguide affects the sensor performance, i.e., its sensitivity. More in detail, it was studied how the surface roughness changes with the placement of the 3D printed items on the building platform. To achieve this purpose, a Phase I distribution-free quality monitoring analysis of the selected manufacturing process was implemented for a small pilot production run. The aim was to check the stability of surface roughness versus the placement of the 3D printed parts on the building platform. The 3D printed sensor’s surface roughness was assessed through a profilometry study. In particular, the surface roughness was determined for the core of the optical waveguide used to excite the SPR phenomena. Furthermore, the SPR sensors were optically characterized to find the existing relationship between their sensitivity and the considered quality of surface finish. In particular, by varying the surface roughness of the used waveguide, the light scattering in the waveguide changes, and the SPR sensitivity changes too, similarly to the light-diffusing fibers covered by gold nanofilms where the guided light is scattered through a plurality of voids distributed in the core. The procedure followed to investigate the sensor roughness, and establishing their performance enabled the optimal operative range for their application in practice to be identified. Finally, a better knowledge of the 3D printing manufacturing process has been achieved to improve quality of surface finish.

High-performance portable grating-based surface plasmon resonance sensor using a tunable laser at normal incidence

Surface plasmon resonance (SPR) sensors are among the most sensitive sensors. In such devices, a grating is a compelling alternative to a prism for the excitation of a surface plasmon, especially in the development of sensors for point-of-care applications due to their compactness and cost-effectiveness. Here, we demonstrate the use of a tunable laser in a grating-based SPR system for further miniaturization and integration. The tunable laser working at normal incidence replaces spectral and moving components, while also simplifying the optical setup. Normal incidence is conventionally avoided due to the complexity of the control of degenerated SPR modes. We investigate, both computationally and experimentally, the splitting of the SPR modes at small nonzero incidences, which is lacking in previously reported studies. By optimizing the grating configuration, we were able to diminish the SPR mode splitting phenomenon when the excitation was feasible with the normal incidence configuration. The fabricated sensor showed a high sensitivity of 1101.6 nm/RIU. Notably, the figure of merit of the sensor, defined as the ratio between the sensitivity and bandwidth of the SPR dip, was 229.5. The experimental results were consistent with the simulation results. We also demonstrate its capability for detecting low concentrations of glucose and creatinine with the limit of detection of 14.2 and 19.1 mmol/L, respectively.

Localized Surface Plasmon Resonance Sensing and its Interplay with Fluidics.

In this Feature Article, we discuss the interplay between fluidics and the localized surface plasmon resonance (LSPR) sensing technique, primarily focusing on its applications in the realm of bio/chemical sensing within fluidic environments. Commencing with a foundational overview of LSPR principles from a sensing perspective, we subsequently showcase the development of a streamlined LSPR chip integrated with microfluidic structures. This integration opens the doors to advanced experiments involving fluid dynamics, greatly expanding the scope of LSPR-based research. Our discussions then turn to the practical implementation of LSPR and microfluidics in real-time biosensing, with a specific emphasis on monitoring DNA polymerase activity. Additionally, we illustrate the direct sensing of biological fluids, exemplified by the analysis of urine, while also shedding light on a unique particle assembly process that occurs on LSPR chips. We not only discuss the significance of LSPR sensing but also explore its potential to investigate a plethora of phenomena at liquid-liquid and solid-liquid interfaces. This is particularly noteworthy, as existing transduction methods and sensors fall short in fully comprehending these interfacial phenomena. Concluding our discussion, we present a futuristic perspective that provides insights into potential opportunities emerging at the intersection of fluidics and LSPR sensing.

Label-free SPR fiber microfluidic sensor with PDA-MA cross-linked lipase for specific detection of tributyrin

As a precursor to butyric acid and also a short-chain triglyceride, tributyrin plays an important role in repairing small intestinal villi, promoting the absorption and utilization of nutrients, and monitoring human health. The traditional carboxylation functionalization method of optical fiber sensors takes a long time and is complicated to operate. Therefore, we need a sensor with a functional period, high sensitivity, and the ability to quickly detect samples to achieve specific detection of tributyrin. In this paper, based on the chemical cross-linking method of polydopamine-maleic acid (PDA-MA), a novel fiber-optic microfluidic surface plasmon resonance (SPR) sensor was proposed to realize the detection of tributyrin. Compared with the traditional functionalization method, the fixation method of PDA-MA chemical cross-linking method not only shortens the functionalization time, but also increases the sensitivity of the sensor. Experimental results show that the sensitivity of the microfluidic sensor coated with PDA reaches 3392.7 nm/RIU, which is 1.75 times that of the uncoated sensor. The sensor has a sensitivity of 8.22 nm/mM in the range of 0.5–5 mM and a response time of only 8 min at the concentration of 1 mM. In addition, the sample detection error of the sensor is within 12 % in the range of 0.5–5 mM. The proposed sensor offers the advantages of low sample consumption (100 μL), high sensitivity, good selectivity, good repeatability, anti-interference ability, and label-free measurement. The sensor holds promising applications in food safety and health monitoring due to its superior performance.

Lossy Mode Resonance Sensors Based on Anisotropic Few-Layer Black Phosphorus.

Lossy mode resonance (LMR) sensors offer a promising avenue to surpass the constraints of conventional surface plasmon resonance (SPR) sensors by delivering enhanced label-free detection capabilities. A notable edge of LMR over SPR is its excitation potential by both transverse electric (TE) and transverse magnetic (TM) polarized light. Yet this merit remains underexplored due to challenges to achieving high sensing performance under both TM and TE polarization within a singular LMR model. This study introduces a theoretical model for an LMR prism refractive index sensor based on a MgF2-few layer black phosphorus-MgF2 configuration, which can achieve angular sensitivity nearing 90° refractive index unit-1 (RIU-1) for both polarizations. Leveraging the distinct anisotropic nature of black phosphorus, the figure of merit (FOM) values along its two principal crystal axes (zigzag and armchair) show great difference, achieving an impressive FOM of 1.178 × 106 RIU-1 along the zigzag direction under TE polarized light and 1.231 × 104 RIU-1 along the armchair direction under TM polarized light. We also provide an analysis of the electric field distribution for each configuration at its respective resonant conditions. The proposed structure paves the way for innovative applications of anisotropic-material-based LMR sensors in various applications.

Nanopore arrays with TMOKE-enhanced high performance sensing

Magneto-plasmon sensing structure based on surface plasmon resonance (SPR) and magneto-optical (MO) effect has become a hot research topic in recent years. In this work, we propose a magneto-plasmon crystal consisting of an Au/Co double-layer nanoporous structure with optically thick Au film as a substrate. Due to the excitation of high-quality SPR, a Fano-like transverse magneto-optical Kerr (TMOKE) spectrum with subnanometer bandwidth is realized. A sensitivity of up to 677 nm RIU−1 is detected under subtle refractive index changes in air, and all the calculated figure of merits (FOM) are higher than 104 RIU−1. In addition, in order to highlight the superiority of the sensing performance of the MO plasmon (MOSPR) sensor, we compare the MOSPR sensor with the SPR sensor and calculate their FOM in different refractive index environments. The results show that the FOM of the MOSPR sensor is two orders of magnitude higher than that of the SPR sensor, which proves that the performance of the MOSPR sensor is significantly better than that of the SPR sensor and provides a theoretical basis for biosensing and gas detection based on magneto plasmon.

Improving surface plasmon resonance sensors with speckle image processing

This paper investigates digital image correlation approaches for assessing speckle patterns produced by surface plasmon resonance (SPR) imaging. An SPR sensor based on the Kretschmann setup comprising a gold-coated prism in a fixed angular position performs refractive index assessments in ethanol solutions. Subsequently, the acquisition system collects the reflected light and processes the speckle field images to evaluate the sensor's sensitivity, noise, and limit of detection. Based on three repetitions under similar conditions, the maximum resolution for the average intensity, zero-mean normalized cross-correlation, and the relative sum of square differences metrics are 4.90×10−4, 2.31×10−5, and 7.45×10−6 RIU, respectively, leading to an improved limit of detection without modifying the optical setup.

Experimental study on ultra-high sensitivity gold-based SPR sensor for refractive index and temperature measurement

We have experimentally demonstrated an ultra-high sensitivity gold-based fiber refractive index (RI) sensor whose main structure is composed of multimode fiber (MMF) and photonic crystal fiber (PCF). The gold film is deposited on V-shaped PCF by magnetron sputtering, and sensing experiments are performed based on the principle of surface plasmon resonance (SPR). Numerical simulation results indicate that the cladding mode of the V-shaped PCF is more capable of stimulating the SPR effect than the core mode. The experimental results show that the RI measurement range of the sensor is 1.333–1.421, with a maximum sensitivity of 10015 nm/RIU. In addition to RI sensing, sensing probes can be coated with polydimethylsiloxane (PDMS) on a gold film for temperature sensing. For temperature detection, the range is from 10 to 100 °C and the maximum sensitivity is 3.5 nm/℃. Besides high sensitivity in RI measurement, the proposed sensor also has good sensing performance in temperature sensing. With the advantages of high sensitivity, good stability, and easy preparation, this sensor has become an important reference in the field of high-performance sensing.

High-sensitivity concentration detection of trace doxycycline in solution by molecular imprinting based on surface plasmon resonance technology

The abuse of doxycycline (DC) will lead to the presence of its residues in animals and water environments, which threatens human health. It is of great significance to detect the micro-content of DC in solution. Based on surface plasmon resonance (SPR) technology, we develop a detection method for trace DC in solution by modifying the SPR sensor chip with a molecular imprinting technique. The results show that the SPR sensor could specifically recognize DC in solution, and the detection limit of this method reaches 10−6µg/mL, which is 100 times lower than that of the ELISA method. The detection signal has good linearity in the concentration range of 10−6−10µg/mL. This method has the advantages of a low detection limit, large linear range, and high specificity for DC detection.

A surface plasmon resonance sensor based on photonic crystal fiber composed of magnesium fluoride and graphene layers to detect aqueous solutions

A surface plasmon resonance sensor based on photonic crystal fiber composed of magnesium fluoride and graphene layers to detect aqueous solutions

Design and Analysis of Surface Plasmon Resonance Sensor with Open-Loop Side-Polished Photonic Crystal Fiber

Design and Analysis of Surface Plasmon Resonance Sensor with Open-Loop Side-Polished Photonic Crystal Fiber

Peptide-Based Recognition Agents of Histamine: A Biopanning Approach with Enhanced Specificity.

Histamine is a biogenic amine that poses a potential threat to public health due to its toxicological effects. In this study, we identified histamine-binding peptides by screening a random 12-mer peptide library, employing a novel biopanning approach that excluded histidine-binding sequences in the final round. This additional step enhanced the selectivity of the peptides and prevented interference from histidine during detection. The binding affinities of synthesized peptides to histamine were assessed using isothermal titration calorimetry (ITC). Among the identified peptides, HBF10 (SGFRDGIEDFLW) and HBF26 (IPLENQHKIYST) showed significant affinity to histamine, with Kavalues of 2.56×104 (M-1) and 8.94×104 (M-1), respectively. Notably, the identified peptides did not demonstrate binding affinity towards histidine, despite its structural similarity to histamine. Subsequently, the surface plasmon resonance (SPR) sensor surface was prepared by immobilizing the peptide HBF26 to investigate the potential of the peptide as a recognition agent for histamine detection. The findings suggest that the identified peptides have an affinity to histamine specifically, showcasing their potential applications as diagnostic agents with specific targeting capabilities.

Design and Development of a Split Ring Resonator and Circular Disc Metasurface Based Graphene/Gold Surface Plasmon Resonance Sensor for Illicit Drugs Detection

Design and Development of a Split Ring Resonator and Circular Disc Metasurface Based Graphene/Gold Surface Plasmon Resonance Sensor for Illicit Drugs Detection

Sodium-based no-core fiber surface plasmon resonance sensor with high sensitivity and narrow FWHM

Since fiber-optic sensors using noble metal-excited surface plasmon resonance (SPR) effects have encountered bottlenecks in improving performance, we propose a fiber-optic sensor using sodium in combination with a no-core fiber (NCF) to measure both refractive index (RI) and temperature. We deposited sodium thin films on the surface of NCF optical fibers and protected them with polymethyl methacrylate (PMMA) or polydimethylsiloxane (PDMS) for RI sensing or temperature sensing. We performed computational simulations and performance analyses of the sensors using the finite element method, and the results show that the sodium-based SPR sensors have higher sensitivity, wider detection range, and narrower full width at half-maximum (FWHM) than the noble metal SPR sensors. SPR sensors with different sodium film thicknesses have different sensing characteristics, so we can get optical fiber sensors with more flexible transmission characteristics, which helps us arrange sensors more conveniently in practical applications. The simulation and numerical results show that when the sensor is used to measure RI, the average sensitivity of the sensor can reach 7977 nm RIU−1, the maximum sensitivity can reach 23100 nm RIU−1, the narrowest FWHM is 14.23 nm, and the maximum figure of merit (FOM) is 719.42 RIU−1 under different thicknesses of sodium film. The corresponding RI ranges from 1.32 to 1.41. When the temperature measurement range is 0 °C ∼ 100 °C, the average sensitivity can reach 7.86 nm °C−1, the maximum temperature sensitivity can reach 21.1 nm °C−1, and the narrowest FWHM is 17.84 nm. In summary, the proposed sodium-based SPR sensor has flexible and high-performance sensing characteristics, and our research work provides more powerful theoretical support for the application of sodium-based plasma devices.

Harnessing quantum plexcitons for enhanced sensitivity and selectivity of creatinine sensor

Despite their widespread usage, surface plasmon resonance (SPR) sensors have several drawbacks, including limited sensitivity and the requirement for sophisticated functionalization chemistry to enhance their performance. In contrast, using quantum states for sensing may result in an enormous increase in sensor performance. These states, however, often need a rigorously controlled environment, which limits their adoption. Recently, there has been a surge of interest in employing quantum plexcitons to solve this conundrum, which has recently been proven to be resilient and robust even in ambient conditions. Here, we report the utilization of plexcitons induced through hybridization of surface plasmon and excitons in a SPR-Otto configuration for sensing creatinine molecules. Using an organic pentamer, BOBzBT2, the ultra-strong coupling regime with a Rabi splitting of 22 % of the uncoupled energy was observed and exploited to monitor the creatinine concentrations. This demonstration proposes a way to combine the benefits of an SPR-based design with the sensitivity offered by quantum plexcitons, which is beneficial for future practical quantum sensing.