Surface Oxidation State Research Articles

Role of Oxide-Derived Cu on the Initial Elementary Reaction Intermediate During Catalytic CO2 Reduction.

The catalytic role of oxide-derived Cu (OD-Cu) in promoting CO2 reduction (CO2R) to C2+ products has been appreciated for decades. However, the dynamic evolution of the surface oxidation states, together with their real correlation to the binding of reaction intermediates, remains unclear due to technical challenges. Here, we show the time-resolved spectroscopic signatures of key OD-Cu-CO2•- intermediates during catalytic CO2 reduction through one electron transfer from nanoseconds to seconds time scale. We generated the initial intermediate CO2•- radicals in the bulk solution and monitored the interfacial reaction kinetics with well-defined OD-Cu (Cu(0), Cu(I), and Cu(II)) nanoparticles. Combined with molecular simulations, transient absorption profiles analysis reveals that Cu(I) induced a faster CO2•- radical coupling reaction than Cu(0), whereas Cu(II) is only reduced to Cu(I) by the CO2•- radical. Furthermore, the newly developed multistep cumulative pulse methodology uncovered the transition in chemical states of mixed OD-Cu during radical coupling reactions. This pulse radiolysis study provides compelling evidence for the beneficial role of subsurface oxides in early time catalytic CO2 transformation.

Tailoring electrochemical CO2 reduction selectivity over CuSn by modulating surface oxidation state with infrared laser treatment

Infrared laser treatment was used to precisely modify the surface structure of CuSn electrodes, effectively fine-tuning the selectivity of reduction products. With increasing laser power, the metallic Cu and Sn surfaces became more oxidized, and the Sn/Cu composition ratio varied with depth and further changed post-EC reaction. The diversity of reduction products, including C1 (CO, CH4, and formate), C2 (C2H4, ethanol, acetate, acetaldehyde, and glycolaldehyde), and C3 (propanol and isopropanol) compounds, shifted towards a more selective production of C1 (CO and formate) products. These tailored behaviors are attributed to variations in interfacial electronic structures, oxidation states, composition ratios, and the interaction between CO2 and the density of states (Cu, O, and Sn) near the Fermi level. The laser treatment method enables precise tuning of electrode surfaces, modulation of reduction products, and enhancement of selectivity. Moreover, this technique presents a novel approach for electrode design in the field of CO2 reduction, offering new avenues for optimizing catalytic performance.

Enhanced photoelectrochemical CO2 reduction activity towards selective generation of alcohols over CuxO/SrTiO3 heterojunction photocathodes

Photoelectrochemical reduction (PECR) of CO2 to value-added chemicals and fuels will reduce the dependency on fossil fuels, also it will solve environmental issues that arise due to greenhouse gases. A heterojunction of CuxO/SrTiO3 with varying post-annealing temperature ranges from 300 to 600 °C (CS300-600) was synthesized by overlying the spin-coated SrTiO3 on electrodeposited Cu2O over the FTO glass substrate. The synthesized photoelectrode's crystallinity and phase formation significantly varied by varying the post-annealing temperature, which was characterized via XRD and Raman spectroscopy. Optical, morphological, type of heterojunction formation and elemental surface oxidation states of photoelectrodes were studied through UV–visible DRS spectrum, FE-SEM, and XPS analysis respectively. Electrocatalytic analysis such as Linear Sweep Voltammetry (LSV), and Electrochemical Impedance Spectrometry (EIS) was employed, thus it conforms to the highest photocurrent density (−1.38 mA/cm2 at −0.6V vs. Ag/AgCl), and low charge transfer resistance (RCT=0.412 kΩ) at the electrode-electrolyte interfaces for CS500 photoelectrode as compared to others photoelectrodes. PECR of CO2 to liquid product formation was evaluated by applying different potential ranges (0 to −0.6 V vs. Ag/AgCl). Highest methanol formation of 48.69 μmol.cm−2hr−1, which is approximately 9 times enhanced as compared to the pure Cu2O (5.62 μmol.cm−2hr−1) photoelectrode at 0 V vs Ag/AgCl for CS500 heterojunction. Optimization of overlaying SrTiO3 synthesis temperature for crystallization formation on Cu2O and applied photoelectrode potential findings could pave the way for designing other new heterojunction types for selective liquid alcohol production.

A New Approach to Single‐Step Fabrication of TiOx‐CeOx Nanoparticles

Mixed metal oxide (MMO) nanoparticles (NPs) are hybrids consisting of two or more nanoscale metal oxides. Advantages of MMO NPs over single metal oxides include improved catalytic activity, enhanced electrical and magnetic properties, and increased thermal stability due to the synergy of the different oxide components. This study presents a novel fabrication route for TiO2‐CeO2 NPs enriched with oxygen vacancies using a Haberland‐type gas aggregation cluster source. The NPs, deposited from different segmented Ti/Ce targets under varying O2 addition, were examined with respect to final composition, morphology, and Ti, Ce surface oxidation states. Particle formation mechanisms are proposed for the observed morphologies. Additionally, available O2 during deposition and its impact on the formation of defective sites were investigated. Defective sites in TiO2‐CeO2 NPs were analyzed using transfer to X‐ray photoelectron spectroscopy and transmission electron microscopy without contact to ambient oxygen. The incorporation of Ce to the target exhibits synergistic effects on the synthesis process. Segmented Ti/Ce targets enable the deposition of a broad range of mixed oxide NPs with diverse compositions and morphologies at considerably enhanced deposition rates, which is vital for practical applications. The presented fabrication approach is expected to be applicable for a broad variety of MMO NPs.

Regulating oxidation states of Cu nanowires for enhanced catalytic reduction of 4-nitrophenol

Abstract The construction of highly efficient and low-cost catalysts is crucial for the reduction reaction of 4-nitrophenol (4-NP). Herein, we provide a simple processing method, including vacuum storage, natural oxidation, and heating oxidation, that effectively regulates the surface oxidation state of copper nanowires and produces copper nanowires with different oxidation states (such as Cu, Cu2O, and CuO). Research has found that CuNW-N (Cu nanowires for vacuum storage) catalysts with a surface composition of 67.9% Cu0, 20.6% Cu+, and 11.5% Cu2+ exhibit the best catalytic performance for the reduction of 4-nitrophenol (4-NP) and their reaction rate constant reaches 0.791 min−1. This work provides a feasible catalyst preparation strategy for the efficient catalytic reduction of 4-NP.

Ultra-sensitive CuAl2O4 Nanoflakes for ppb level detection of Isopropanol

Trace-level detection of isopropanol is important for human health monitoring and air quality surveillance. In this work, we report synthesis of high surface area two-dimensional (2D) nanoflakes of CuAl2O4 using surfactant-assisted hydrothermal process and its application in ppb level detection of isopropanol. X-ray diffraction revealed the polycrystalline nature of the spinel and a nano crystallite size of 42 nm. The 2D morphology of CuAl2O4 was confirmed using field emission scanning electron microscope whereas BET revealed the mesoporous nature and a high surface area of 41.8 m2g-1. The surface oxidation states of the material were found through X-ray photoelectron spectroscopy. The 2D CuAl2O4 demonstrated excellent sensing towards isopropanol with its response varying from 11.8 to 84.5 % (500 ppb–10 ppm) at 300 °C. The limit of detection of the spinel was found to be 56 ppb at its optimum operating temperature of 300 °C. In addition, the sensing layer was found to have response times in range 1101 s for 500 ppb to 168 s for 10 ppm and recovery times in the range 300 s for 500 ppb to 570 s for 10 ppm.

Tuning surface Mn defects on LaMnO3 perovskite oxides by selective dissolution strategy for enhanced phosphate removal

Selective dissolution is widely used to adjust the surface state of LaMnO3 perovskite oxides. In this study, LaMnO3(LMO) with B-Site vacancies was synthesized using ascorbic acid to selectively remove Mn cations and enhance phosphate adsorption. The optimized LMO with Mn defects (LMO-AA3) presented large surface area, plenty of mesoporosity and suitable electronic structure. Particularly, the adsorption capacity (113.48 mg/g) of LMO-AA3 was about10 times that of LMO. Adsorption experiments showed adsorption occurred both chemically and physically on the heterogeneous adsorption surfaces, as the pseudo-second-order kinetic model and the Redlich-Peterson isotherm model predicted. The stimulated mechanism of LMO-AA3 achieved phosphate absorption through enhancing electrostatic attraction and ligand exchange by –OH groups. Regeneration testing showed that LMO-AA3 can be used for both high and low-concentration purification of phosphate. The selectively remove Mn cations method may offer an appropriate choice for enhancing the material characteristics of effective phosphate capture.

Controlling the surface oxidation state of halogenated Cu-based catalyst for electrochemical reduction of carbon dioxide to ethylene

The electrochemical CO2 reduction reaction (CO2RR) has attracted significant attention as strategy for achieving carbon neutrality. Among the candidate materials for the CO2RR, Cu-based electrocatalysts can potentially produce various high-value carbon products. However, the diversity of their products obtained via CO2RR induces low selectivity and hinders the acquisition of a specific product with a high yield. Herein, we suggest the strategies for enhancing ethylene production via CO2RR by reconstructing the oxidation states of the Cu-based catalysts. The introduced chemical oxidation and following halogenation contributes to modulate the electron structures and oxidation states of the electrodeposited polygonal Cu catalyst surface. In particular, the chemical oxidation step induces the coexistence of Cu0 and Cu+ on the catalyst surface which stabilize the CO2 adsorption onto the catalyst surface, and the halogenation maintains the Cu0/Cu+ ratio of the catalyst surface during the CO2RR. As a result, controlling the oxidation states of Cu-based catalyst improves the ethylene production selectivity up to 47.0 % of Faradaic efficiency. Furthermore, we employ a membrane electrode assembly-based electrolyzer for CO2RR which is used for commercialization, and achieve high ethylene production with a partial current density of 124.7 mA cm–2.

Optimizing symmetric supercapacitor performance through rational design of Zr/Cu/Fe Oxide-Modified Poly(vinyl alcohol) hybrid nanofibers

Present work, ZrO2/CuO/PVA (ZC-PVA), ZrO2/Fe2O3/PVA (ZF-PVA) and ZrO2/CuO/Fe2O3/PVA (ZCF-PVA) nanofibers were synthesized by cost effective electrospinning method. The ZCF-PVA nanofiber prepared in this study were subjected to analysis using X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Fourier-transform infrared (FT-IR) spectroscopy, and X-ray photoelectron spectroscopy (XPS) techniques, individually. XRD was employed to ascertain both the structure and crystallite size of the synthesized materials. SEM and FT-IR analysis were used to identify the morphology and functional groups present in the prepared ZC-PVA, ZF-PVA and ZCF-PVA nanofibers. XPS confirmed the surface elemental composition and oxidation states of Zr4+, Cu2+, and Fe3+ in ZCF-PVA nanofiber comprising ZrO2, CuO, and α-Fe2O3. In three electrode configuration ZCF-PVA nanofiber shows significantly higher specific capacitance of 824F/g at 1 A/g current density under 1 M KOH. The generation of synergic effect between multi valence oxidation states of mixed metal oxides and polymer (ZCF-PVA) enhances the capacitive behavior. The ZCF-PVA symmetric device exhibits 184F/g at 0.5 A/g current density with 91 % capacitance retention and 94 % of coulombic efficiency even after 5000 cycles at 3 A/g of current density.

Role of catalyst oxidation states in the selective detection of reducing gases: A comparative study of nanocomposites based on Au and chemically/thermally reduced graphene oxide

Catalyst-loaded reduced graphene oxide (rGO) is a promising material for developing high-performance gas sensors. In this work, surface functionalization is achieved by loading different quantities of nanogold (Au) on chemically and thermally reduced graphene oxide (CRGO and TRGO). These materials showed selective gas response toward reducing gases such as hydrogen (H2), carbon monoxide (CO), and methane (CH4) in the temperature range RT to 150 °C. The quantity of Au catalysts and their oxidation states in the films influenced the selectivity attributes of the studied sensors. The surface oxidation states of the Au catalyst are different for CRGO-Au and TRGO-Au films. It is apparent from the results that the difference in the Au oxidation states is due to the variation in surface oxygen functionalities of the base matrix CRGO and TRGO. The experimental results are tallied with the proposed gas selectivity mechanism of CRGO-Au and TRGO-Au films.Novelty of the Work:In reduced graphene oxide based gas sensors, the combined influence of the graphene oxide reduction method, gold (Au) catalyst quantity, and valence oxidation states (in the Au catalyst) on the gas selectivity is rarely reported. The available reports only focus on examining the metallic gold (Au0) phase of the catalyst. However, it is necessary to note that Au can also exist in various higher oxidation states (Au+1, Au+2, Au+3, etc.), which provide selective gas adsorption sites. Therefore, this work addresses the above issue by employing chemically reduced graphene oxide (CRGO) and thermally reduced graphene oxide (TRGO) decorated with Au nanoparticles (Au wt% = 1 %, 50 % & 90 %) for the selective sensing of reducing gases.

Electronic perturbation of Cu nanowire surfaces with functionalized graphdiyne for enhanced CO2 reduction reaction

Abstract Electronic perturbation of Cu catalysts surface is crucial for optimizing electrochemical CO2 reduction activity, yet still poses great challenges. Herein, nanostructured Cu nanowires (NW) with fine-tuned surface electronic structure are achieved via surface encapsulation with electron-withdrawing (–F) and -donating (–Me) group-functionalized graphdiynes (R-GDY, R = –F and –Me), and the resulting catalysts, denoted as R-GDY/Cu NW, display distinct CO2 reduction performances. In-situ electrochemical spectroscopy revealed that the *CO (a key intermediate of the CO2 reduction reaction) binding affinity and consequent *CO coverage positively correlate to the Cu surface oxidation state, leading to the favorable C–C coupling on F-GDY/Cu NW over Me-GDY/Cu NW. Electrochemical measurements corroborate the favorable C2H4 production with an optimum C2+ selectivity of 73.15% ± 2.5% observed for F-GDY/Cu NW, while the predominant CH4 production is favored by Me-GDY/Cu NW. Furthermore, leveraging the *Cu–OH/*CO ratio as a descriptor, mechanistic investigation reveals that the protonation of distinct adsorbed *CO facilitated by *Cu–OH is crucial for the selective generation of C2H4 and CH4 on F-GDY/Cu NW and Me-GDY/Cu NW, respectively.

Unveiling Key Interface Characteristics of Ni/Yttria-Stabilized Zirconia Solid Oxide Cell Electrodes in H2O Electroreduction Using Operando X-ray Photoelectron Spectroscopy.

Nickel/yttria-stabilized zirconia (YSZ) composites are the most commonly used fuel electrodes for solid oxide cells. While microstructural changes of Ni/YSZ during operational conditions have been thoroughly investigated, there is limited knowledge regarding Ni/YSZ surface chemistry under working conditions. In this study, we examine the interaction between Ni/YSZ electrodes and water vapor under open circuit and polarization conditions, utilizing near ambient pressure soft and hard X-ray photoelectron spectroscopies. Miniature cells with conventional porous Ni/YSZ composite cermet cathodes were modified to facilitate the direct spectroscopic observation of the functional electrode's areas close to the interface with the YSZ electrolyte. The results highlight dynamic changes in the oxidation state and composition of Ni/YSZ under H2 and H2O atmospheres. We also quantify the accumulation of impurities on the electrode surface. Through adjustments in the pretreatment of the cell, the correlation between the nickel surface oxidation state and the cell's electrochemical performance during H2O electroreduction is established. It is unequivocally shown that nickel surface oxidation in H2O electrolysis favors NiO over Ni(OH)x, providing critical insights into the mechanism of Ni-phase redistribution within the electrode during long-term operation. Depth-dependent photoemission measurements, combined with theoretical quantitative simulations, reveal that NiO and Ni phases are uniformly mixed on the surface during H2O electrolysis. This differs from the conventional expectation of a NiO-shell/Ni-core configuration in gas phase oxidation. These findings provide crucial insights into the surface chemistry of Ni/YSZ electrodes under conditions relevant to H2O electrolysis, elucidating their impact on the electrochemical performance of the cell.

Multicolor circularly polarized luminescence from chiral carbon dots and cellulose nanocrystals assemblies for visual polarization detection

Chiral carbon dots (CCDs) combined with outstanding photoluminescence and unique chirality have become intriguing carbon-based nanomaterials, however, the realization of the optical activity in both ground and excited states remains a great challenge. To overcome this difficulty, multicolor CCDs have been synthesized by changing surface oxidation states and P atom doping via solvothermal route, which emit unusual near-ultraviolet, and blue, yellow and red fluorescence with high photoluminescence quantum yields (PLQY) of 28.99%, 22.55%, 84.63%, and 75.73%, respectively. Benefiting from the excellent luminescence of CCDs and chiral environment of cellulose nanocrystals (CNCs), a series of CCDs@CNCs composite films were produced by matrix-assisted method. The electrostatic, H-bonds and vdWs interactions are found to drive the formation of co-assembly and facilitate the chiral transfer and amplify between CNCs and chromophores. Thus, the CCDs@CNCs films display bright and multicolor right-handed circularly polarized luminescence (CPL) with extremely high luminescence dissymmetry factor (glum) values of −0.24 to −0.90. The synergy of intense glum and high efficiency of multicolor composite films endow them with a potential for visual polarization detection. This research provides inspiration and feasibility for constructing CPL-active materials in co-assembly system and harvesting high glum value.

Zn-Doped MnO2 microflake pseudocapacitive cathode on Ni(OH)2/Ni-Foam substrate as a promising charge storage material

Zn-doped MnO2 microflakes cathode material on Ni(OH)2/Ni foam has been synthesized and characterized as well as tested its electrochemical performances in 3 M KOH solution. The present work varies the amounts of Zn dopant in MnO2 system to improve its capability in energy storage. Material identification has been simply confirmed with XRD, SEM, TEM, and XPS analysis. It is expected the Zn dopant will induce surface defects such as ZnMn2- or ZnMn0 and oxygen vacancy, leading to enhanced charge storage efficiency. In addition, XPS analysis reveals the existence of positively charged oxygen vacancy and the surface charge of ZnMn2- or ZnMn0 induce different surface oxidation states of Mn2+ and Mn4+. The oxidation states of Mn could accommodate the redox reactions involving ion adsorption and intercalation during pseudocapacitive charge and discharge processes. Substituting Zn into Mn sites is optimized with MnZn-1.5 which reaches a specific capacitance of 1601F/g at a 0.4 VAg/AgCl in KOH solution. This work demonstrates a promising material system for supercapacitor applications using Zn doping with a simple preparation process to support a large-scale application.

In-situ synthesis of coral reef-like synergistic zinc cobalt oxide and zinc manganese oxide composite as a battery-type electrode material for supercapacitors

Recently, in-situ preparation of metal oxide composite structures has gained much importance in fabricating electrode materials for energy storage and conversion devices because of its advantageous properties of beneficial interfacial contact, high conductivity, good synergism, short ion diffusion distance, better electrochemical performance, etc. Binary transition metal oxides (BTMOs) are given great attention for their significant electrochemical performances over primary MOs because of the two metal ions with different valent states for the redox reactions. In this study, we synthesize zinc cobalt oxide (ZnCo2O4) and zinc manganese oxide (ZnMn2O4) composite via a solvothermal synthetic method. The existence of both phases is identified using an X-ray diffraction analysis (XRD). The unique coral reef-like structures of the composite electrode are analysed via field emission scanning electron microscopy, and the nanostructure was identified using transmission electron microscopy. The X-ray photoelectron spectroscopy confirms the surface oxidation states of the composite and supports the XRD analysis. The synergetic composite electrode provides a large surface area of 50.86 m2 g−1 with many pores. The composite electrode has a specific capacity of 250 C g−1 at 1 A g−1. The ZCO/ZMO composite demonstrated impressive stability, retaining a specific capacity of 180 C g−1 at 6 A g−1 over 5000 cycles.

WLI, XPS and SEM/FIB/EDS Surface Characterization of an Electrically Fluted Bearing Raceway

Electrical bearing currents may disturb the performance of the bearings via electro-corrosion if they surpass a limit of ca. 0.1 to 0.3 A/mm2. A continuous current flow, or, after a longer time span, an alternating current or a repeating impulse-like current, damages the raceway surface, leading in many cases to a fluting pattern on the raceway. Increased bearing vibration, audible noise, and decreased bearing lubrication as a result may demand a replacement of the bearings. Here, an electrically corroded axial ball bearing (type 51208) with fluting patterns is investigated. The bearing was lubricated with grease lubrication and was exposed to 4 A DC current flow. It is shown that the electric current flow causes higher concentrations of iron oxides and iron carbides on the bearing raceway surface together with increased surface roughness, leading to a mixed lubrication also at elevated bearing speeds up to 1500 rpm. The “electrically insulating” iron oxide layer and the “mechanically hard” iron carbide layer on the bearing steel are analysed by WLI, XPS, SEM, and EDS. White Light Interferometry (WLI) is used to provide an accurate measurement of the surface topography and roughness. X-ray Photoelectron Spectroscopy (XPS) measurements are conducted to analyze the chemical surface composition and oxidation states. Scanning Electron Microscopy (SEM) is applied for high-resolution imaging of the surface morphology, while the Focused Ion Beam (FIB) is used to cut a trench into the bearing surface to inspect the surface layers. With the Energy Dispersive X-ray spectrometry (EDS), the presence of composing elements is identified, determining their relative concentrations. The electrically-caused iron oxide and iron carbide may develop periodically along the raceway due to the perpendicular vibrations of the rolling ball on the raceway, leading gradually to the fluting pattern. Still, a simulation of this vibration-induced fluting-generation process from the start with the first surface craters—of the molten local contact spots—to the final fluting pattern is missing.

Operando Monitoring of Homolytic Cleavage of H2 into Surface Hydrides on Defective Cerium Dioxide Nanoparticles

AbstractThe use of ceria as catalyst in hydrogenation reactions is a recent trend, as they were uncovered to be active on a number of substrates, including alkynes, alkenes, and enones. While some studies focused on the use of well‐defined shapes, others emphasized the interest of defective structures. Overall, the meeting point of these studies is the need to characterize the surface reactivity vs. H2, by considering a number of interesting textures (films, nanopowders with various grain size or porosity), using monitoring techniques that preserve the original features of the materials. A key question is in particular to assess the possibility to form surface hydride through homolytic H2 splitting at cerium sites rather than at the oxygen one, a route recently highlighted as plausible. To address this question on small crystallites of CeO2, we designed a low‐temperature synthetic route for nanorods with an average grain size of 10 nm. Then, we employed near‐ambient‐pressure X‐ray photoelectron spectroscopy as an operando tool to monitor the cerium surface oxidation state during the initial annealing of the nanopowders, followed by exposure to a moderate pressure of H2 (0.52 mbar). We demonstrate that H2 homolytic splitting at cerium sites is the main activation process on this surface at 100 °C, leading to the oxidation of ca. 30 % of the surface cerium atoms from Ce3+ to Ce4+. The surface hydride species were however not stable at 250 °C, H2 was released, and cerium reduced back to Ce3+. A similar mechanism was observed on a defective ceria material obtained by calcination of CeO(OH)2, with comparable intensities. Overall, we report here CeO2 nanorods, exposing predominantly {100} and {110} facets, as showing an interesting surface reactivity for potential application in hydrogenation reactions, and we expose a straight operando methodology to delineate suitable temperatures to be used.

Genotoxicity and heating Performance of VxFe3-xO4 nanoparticles in Health applications

The applications of magnetic nanoparticles (MNPs) as biocatalysts in different biomedical areas have been evolved very recently. One of the main challenges in this field is to design affective MNPs surfaces with catalytically active atomic centres, while producing minimal toxicological side effects on the hosting cell or tissues. MNPs of vanadium spinel ferrite (VFe2O4) are a promising material for mimicking the action of natural enzymes in degrading harmful substrates due to the presence of active V5+ centres. However, the toxicity of this material has not been yet studied in detail enough to grant biomedical safety. In this work, we have extensively measured the structural, compositional, and magnetic properties of a series of VxFe3-xO4 spinel ferrite MNPs to assess the surface composition and oxidation state of V atoms, and also performed systematic and extensive in vitro cytotoxicity and genotoxicity testing required to assess their safety in potential clinical applications. We could establish the presence of V5+ at the particle surface even in water-based colloidal samples at pH 7, as well as different amounts of V2+ and V3+ substitution at the A and B sites of the spinel structure. All samples showed large heating efficiency with Specific Loss Power values up to 400 W/g (H0 = 30 kA/m; f = 700 kHz). Samples analysed for safety in human hepatocellular carcinoma (HepG2) cell line with up to 24h of exposure showed that these MNPs did not induce major genomic abnormalities such as micronuclei, nuclear buds, or nucleoplasmic bridges (MNIs, NBUDs, and NPBs), nor did they cause DNA double-strand breaks (DSBs) or aneugenic effects—types of damage considered most harmful to cellular genetic material. The present study is an essential step towards the use of these type of nanomaterials in any biomedical or clinical application.

An investigation into the short-circuit characteristics of Sic MOSFET power devices

Silicon carbide (SiC) metal-oxide-semiconductor field-effect transistor (MOSFET) devices exhibit substantial prospects for application under extreme operational conditions, including elevated temperatures, high voltages, and high frequencies. Nevertheless, owing to their distinctive material and structural attributes, SiC MOSFET devices are not devoid of challenges, with the short-circuit phenomenon constituting a pivotal avenue of inquiry. The short-circuit effect pertains to the abrupt escalation of leakage current that these devices might undergo under elevated voltage conditions, thereby exerting a perturbing influence on their stability and reliability. Investigations into the short-circuit effect predominantly revolve around two dimensions: one involves comprehending its underlying physical mechanisms, while the other centers on identifying commensurate remedial approaches.With respect to the underlying physical mechanisms, researchers have discerned that the elevated breakdown field strength and augmented carrier mobility intrinsic to SiC materials engender an augmentation in leakage current, consequently giving rise to the short-circuit effect. Furthermore, factors such as oxide layer anomalies and surface states are also conceivable catalysts for the surge in leakage current. To rectify this predicament, scholars have proffered a panoply of stratagems, encompassing the optimization of material synthesis processes, enhancement of oxide layer quality, refinement of device structural designs, and incorporation of protective circuitry, among others. In summation, the investigation of the short-circuit effect in silicon carbide MOSFET devices is fundamentally aimed at attaining an in-depth comprehension of its causative mechanisms. Moreover, it endeavors to proffer efficacious resolutions conducive to augmenting the reliability and steadfastness of these devices within high-temperature and high-voltage environments, thereby facilitating their widespread integration within the ambit of high-performance power electronics.

Surface Passivation toward Multiple Inherent Dangling Bonds in Indium Phosphide Quantum Dots.

Indium phosphide (InP) quantum dots (QDs) have become the most recognized prospect to be less-toxic surrogates for Cd-based optoelectronic systems. Due to the particularly dangling bonds (DBs) and the undesirable oxides, the photoluminescence performance and stability of InP QDs remain to be improved. Previous investigations largely focus on eliminating P-DBs and resultant surface oxidation states; however, little attention has been paid to the adverse effects of the surface In-DBs on InP QDs. This work demonstrates a facile one-step surface peeling and passivation treatment method for both In- and P-DBs for InP QDs. Meanwhile, the surface treatment may also effectively support the encapsulation of the ZnSe shell. Finally, the generated InP/ZnSe QDs display a narrower full width at half-maximum (fwhm) of ∼48 nm, higher photoluminescence quantum yields (PLQYs) of ∼70%, and superior stability. This work enlarges the surface chemistry engineering consideration of InP QDs and considerably promotes the development of efficient and stable optoelectronic devices.