Surface Of Titanium Dental Implants Research Articles

MICROSTRUCTURE, CHEMICAL COMPOSITION, AND NANOMECHANICAL PROPERTIES OF ARC-PVD ZrTa/ZrTaO2 BILAYER COATINGS

The results of vacuum-arc deposition of thin bilayer ZrTa/ZrTaO2 coatings on the surface of titanium dental implants, AISI-316L stainless steel are presented. The structure, phase and chemical composition of deposited coatings have been investigated by means of scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) and X-ray diffraction analysis XRD. Nanomechanical properties have been investigated by nanoindentation method. The obtained results can be useful for optimization of implant surfaces to prevent corrosion and mechanical failure, thereby improving osseointegration.

Laser-Induced Temperature Changes on the Outer Surface of Titanium Dental Implants: An In Vitro Study.

To measure the surface temperature distribution after using a CO2 laser to heat titanium dental implants via different power settings, application intervals, and irradiation times. A total of 10 tissue-level titanium implants (Screw-Line Promote Plus, Camlog; 4.3 × 11 mm) were placed (EpoFix, Struers) and irradiated with a CO2 laser (Denta 2, Lutronic) with a wavelength of 10.6 μm at power levels of 4 watts (Group 1), 6 watts (Group 2), 8 watts (Group 3), and 10 watts (Group 4). A continuous beam mode (setting I) and noncontinuous beam modes with 5-second (setting II) and 10-second (setting III) pause intervals were used. For each setting, a total irradiation time of 50 seconds was used and repeated 10 times. The temperature was measured using external thermocouple (Testo) in contact with the implant surface at the implant shoulder, middle, and apex. A linear regression model was used to analyze the data (P = .05). Setting I demonstrated the most rapid increase in implant surface temperature in all three test sites as well as the greatest total temperature at 50 seconds of irradiation time. The greater the pause interval (settings II and III) during the 50 seconds of irradiation, the lower the rate of temperature increase as well as the total temperature in all three test sites and with all power levels. The average temperature difference between the apex and shoulder site was significant for setting III for all groups, but not for any groups in settings I and II. Heating the internal aspect of an implant with a CO2 laser produces different temperature distribution profiles depending on the laser power level and the application interval. Laser-beam irradiation leads to a temperature gradient, which is greatest at the implant apex and smallest at the implant shoulder.

Improvement of osseointegration efficacy of titanium implant through plasma surface treatment

A novel plasma treatment source for generating cylindrical plasma on the surface of titanium dental implants is developed herein. Using the titanium implant as an electrode and the packaging wall as a dielectric barrier, a dielectric barrier discharge (DBD) plasma was generated, allowing the implant to remain sterile. Numerical and experimental investigations were conducted to determine the optimal discharge conditions for eliminating hydrocarbon impurities, which are known to degrade the bioactivity of the implant. XPS measurement confirmed that plasma treatment reduced the amount of carbon impurities on the implant surface by approximately 60%. Additionally, in vitro experiments demonstrated that the surface treatment significantly improved cell adhesion, proliferation, and differentiation. Collectively, we proposed a plasma treatment source for dental implants that successfully removes carbon impurities and facilitate the osseointegration of SLA implants.

Benefits of Residual Aluminum Oxide for Sand Blasting Titanium Dental Implants: Osseointegration and Bactericidal Effects.

Objectives. The purpose of this work was to determine the influence of residual alumina after sand blasting treatment in titanium dental implants. This paper studied the effect of alumina on physico-chemical surface properties, such as: surface wettability, surface energy. Osseointegration and bacteria adhesion were determined in order to determine the effect of the abrasive particles. Materials and Methods. Three surfaces were studied: (1) as-received, (2) rough surface with residual alumina from sand blasting on the surface and (3) with the same roughness but without residual alumina. Roughness was determined by white light interferometer microscopy. Surface wettability was evaluated with a contact angle video-based system and the surface free energy by means of Owens and Wendt equation. Scanning electron microscopy equipped with microanalysis was used to study the morphology and determine the chemical composition of the surfaces. Bacteria (Lactobacillus salivarius and Streptococcus sanguinis) were cultured in each surface. In total, 110 dental implants were placed into the bone of eight minipigs in order to compare the osseointegration. The percentage of bone-to-implant contact was determined after 4 and 6 weeks of implantation with histometric analysis. Results. The surfaces with residual alumina presented a lower surface free energy than clean surfaces. The in vivo studies demonstrated that the residual alumina accelerated bone tissue growth at different implantation times, in relation to clean dental implants. In addition, residual alumina showed a bactericidal effect by decreasing the quantity of bacteria adhering to the titanium. Conclusions. It is possible to verify the benefits that the alumina (percentages around 8% in weight) produces on the surface of titanium dental implants. Clinical relevance. Clinicians should be aware of the benefits of sand-blasted alumina due to the physico-chemical surface changes demonstrated in in vivo tests.

Optimization of the surface of titanium dental implants of grade 5 alloy by barrier glass ceramic coating

Optimization of the surface of titanium dental implants of grade 5 alloy by barrier glass ceramic coating

Decontamination of Ti Oxide Surfaces by Using Ultraviolet Light: Hg-Vapor vs. LED-Based Irradiation.

C-range Ultraviolet (UVC) mercury (Hg)-vapor lamps have shown the successful decontamination of hydrocarbons and antimicrobial effects from titanium surfaces. This study focused on surface chemistry modifications of titanium dental implants by using two different light sources, Hg-vapor lamps and Light Emitting Diodes (LEDs), so as to compare the effectivity of both photofunctionalization technologies. Two different devices, a small Hg-vapor lamp (λ = 254 nm) and a pair of closely placed LEDs (λ = 278 nm), were used to irradiate the implants for 12 min. X-ray Photoelectron Spectroscopy (XPS) was employed to characterize the chemical composition of the surfaces, analysing the samples before and after the lighting treatment, performing a wide and narrow scan around the energy peaks of carbon, oxygen and titanium. XPS analysis showed a reduction in the concentration of surface hydrocarbons in both UVC technologies from around 26 to 23.4 C at.% (carbon atomic concentration). Besides, simultaneously, an increase in concentration of oxygen and titanium was observed. LED-based UVC photofunctionalization has been suggested to be as effective a method as Hg-vapor lamps to remove the hydrocarbons from the surface of titanium dental implants. Therefore, due to the increase in worldwide mercury limitations, LED-based technology could be a good alternative decontamination source.

Bioactive Effects of Low-Temperature Argon-Oxygen Plasma on a Titanium Implant Surface.

Although titanium is the most commonly used dental implant material, its biological aging directly leads to a lower rate of osseointegration. The aim of this study is to treat aged titanium disc surfaces using low-temperature argon–oxygen plasma (LTAOP) to obtain a more hydrophilic surface in order to enhance biological activities of osteoblasts on dental implant materials. In this study, smooth-machined titanium (SM Ti) and sandblasted and acid-etched titanium (SLA Ti) substrates were used. Aged titanium discs (SM and SLA Ti) were activated by LTAOP and the surface properties were analyzed. Osteoblasts were then seeded onto the aged and LTAOP-treated surfaces. Cell morphology, viability, and features of osteogenesis were examined. We showed that after the LTAOP treatment, the surfaces of both SM and SLA titanium substrates become more hydrophilic with a larger active oxygen species composition, whereas no obvious morphological changes were observed. Osteoblasts were found to be attached and stretched well on the surfaces of LTAOP treatment specimens. Moreover, the proliferation and osteocalcin secretion of osteoblasts on the plasma-activated titanium samples were superior to the untreated counterparts. LTAOP activation can enhance the attachment, proliferation, and mineralization of osteoblasts on the surfaces of the aged titanium substrates. This research provides a new strategy to modify the surface of titanium dental implants for improved biological functions.

The role of bacterial biofilm and mechanical forces in modulating dental implant failures

Currently many assume that bacteria are the primary etiological factor associated with failure of titanium dental implants. However, emerging data indicates a possible role for mechanical forces in implant failure. This study is based on the hypothesis that the synergistic effect of mechanical forces and bacterial biofilm can lead to surface damage resulting in in vivo release of metallic particles. The primary aim of the study was to develop a dynamic fatigue test method for dental implants immersed in wet environments such as; (i) 0.01 M phosphate buffer saline (PBS); (ii) lactic acid (pH = 5); (iii) bacterial polyculture. Four dental implants each were subjected to fatigue loading from 45 N to 450 N at 4 Hz for 2 million cycles while immersed in (i) PBS (negative control); (ii) bacterial culture (test); and (iii) lactic acid (positive control). Post-testing, optical microscopy, x-ray photoelectron spectroscopy, and electrochemical corrosion tests were performed to evaluate the surface morphology, chemistry, and potential, respectively, of titanium implants. Post-testing, surface discoloration was evident in all three groups. However, the surface damage was further established in XPS analyses of test specimens, which showed that the interplay of bacterial biofilm and mechanical forces resulted in thinning of the TiO2. Lower corrosion potential (Ecorr) of the test specimens compared to positive and negative controls also illustrated damage to the oxide layer. However, other electrochemical parameters such as linear polarization resistance (LPR) and corrosion rate (CR) were comparable among the groups indicating the corrosion resistance post-testing. The synergistic effect of cyclic occlusal loading and bacteria biofilm could negatively affect the surface of titanium dental implants.

Effect of fluoride on the corrosion behavior of nanostructured Ti-24Nb-4Zr-8Sn alloy in acidulated artificial saliva

The surface of titanium dental implants is highly susceptible to aggressive fluoride ions in the oral environment. Nanotechnology has proven an effective approach to improve the stability and corrosion resistance of titanium by applying a passive film. In this study, we investigated the effects of fluoride on the corrosion behavior of nanostructured (NS) Ti-24Nb-4Zr-8Sn (Ti2448) alloy in acidulated artificial saliva (AAS) at 37 °C, and then conducted comparisons with its coarse grained (CG) counterpart. Electrochemical techniques, such as potentiodynamic polarization and electrochemical impedance spectroscopy (EIS), as well as surface analysis including X-ray photoelectron spectroscopy (XPS) with argon ion sputtering, and scanning electronic microscopy (SEM) were employed to evaluate the effects of fluoride on sensitivity to pitting and the tolerance of Ti2448 to fluoride in AAS solution. The results demonstrate that corrosion current density increased with F− concentration. In all respects, the NS Ti2448 alloy presented corrosion resistance superior to that of its coarse grained (CG) counterpart at low F− concentrations (≤0.1%). Furthermore, a high content of F− (1%) was shown to promote the active dissolution of both alloys by increasing the rate of corrosion. Following immersion in the fluoridated AAS solution for 60 days, a tissue-friendly compound, Ca3(PO4)2, was detected on the surface of the NS when F− = 0.01% and Na2TiF6 was identified as the main component in the corrosion products of the CG as well as NS Ti2448 alloys when F− = 1%. High concentrations of F− produced pitting corrosion on the CG alloy, whereas NS Ti2448 alloy presented general corrosion in the form of lamellar separation under the same conditions. These findings demonstrate the superior corrosion resistance of the NS Ti2448 alloy as well as lower pitting sensitivity and higher tolerance to fluoride due mainly to grain refinement.

Experimental studies of the effect of low frequency ultrasound on the wettability of the surface of titanium dental implants

Experimental studies of the effect of low frequency ultrasound on the wettability of the surface of titanium dental implants

Residual Contaminations of Silicon-Based Glass, Alumina and Aluminum Grits on a Titanium Surface After Sandblasting

Sandblasting (grit-blasting) is a commonly used surface treatment method for roughening the surface of titanium dental implants. Today, alumina (Al2O3) grits with various sizes are widely used for this purpose, due to their good surface roughening effects. However, sandblasting with Al2O3 grits also introduces impurities to the surface of the Ti implant, which may adversely affect the osseointegration process of the implant. This raises the question as to the use of Al2O3 as the most suitable type of sandblasting grit, considering the contaminations to the titanium implant in addition to roughening effects. This study evaluates Al2O3, a silicon-based (silica, SiO2) glass and Al metal grits in terms of both roughing effects and contamination to the titanium implant surface. Thirty commercially pure grade 2 (CP2) titanium plates were grit-blasted using various grits. Surface roughness average (R a) of all grit-blasted plate was measured. In addition, SEM/EDX analysis was performed to detect the morphology and elements on the titanium specimen surface before and after sandblasting. Results showed that each type of grits has its own advantages and disadvantages. This said, Al2O3 might be the most suitable material among the three tested grit materials for sandblasting a titanium dental implant surface.

Study of the effects of detoxification treatments on the surface of titanium dental implants (733.5)

Aim: To understand the effects of implant chemical treatment on the surface of two grades of Titanium. The solutions in this study are typically used in the clinical setting for implant sterilization.Methodology: Prior to treatment, disks of pure Ti (cpTi) and alloy (Ti14Al6V) were cut and polished. The surfaces were imaged with 3D microscopy (Keyence VHX 2000) and Atomic Force Microscopy (AFM Workshop). Treatment was performed with a series of compounds including citric acid, hydrogen peroxide, chlorhexidine‐gluconate, sodium fluoride, and several others. The treatments included both immersions in solution and rubbing with a cloth. pH was quantified before and after treatment with a pH meter (Metler Toledo).Results: Surface pitting was seen in both methods with solutions having pH蠄3 on both grades tested. Surface attack was more apparent with cpTi versus the same treatment preformed on the alloy. No significant change was seen with both methods in solutions with a pH>5. Oxidation was seen in both methods after treatment with cpTi in antibiotic treatments. AFM analysis further revealed pitting.Conclusion: Acidic environments coupled with rubbing were shown to cause oxidation of the surface of both Ti grades. These observations show that surface damage of dental alloys can be potentially induced prior to implantation. Additional studies will study particle dissociation due to treatments.

Titanium Corrosion Mechanisms in the Oral Environment: A Retrieval Study.

Corrosion of titanium dental implants has been associated with implant failure and is considered one of the triggering factors for peri-implantitis. This corrosion is concerning, because a large amount of metal ions and debris are generated in this process, the accumulation of which may lead to adverse tissue reactions in vivo. The goal of this study is to investigate the mechanisms for implant degradation by evaluating the surface of five titanium dental implants retrieved due to peri-implantitis. The results demonstrated that all the implants were subjected to very acidic environments, which, in combination with normal implant loading, led to cases of severe implant discoloration, pitting attack, cracking and fretting-crevice corrosion. The results suggest that acidic environments induced by bacterial biofilms and/or inflammatory processes may trigger oxidation of the surface of titanium dental implants. The corrosive process can lead to permanent breakdown of the oxide film, which, besides releasing metal ions and debris in vivo, may also hinder re-integration of the implant surface with surrounding bone.

Effects of Surface Charges on Dental Implants: Past, Present, and Future

Osseointegration is a major factor influencing the success of dental implantation. To achieve rapid and strong, durable osseointegration, biomaterial researchers have investigated various surface treatment methods for dental subgingival titanium (Ti) implants. This paper focuses on surface-charge modification on the surface of titanium dental implants, which is a relatively new and very promising methodology for improving the implants' osseointegration properties. We give an overview on both theoretical explanations on how surface-charge affects the implants' osseointegration, as well as a potential surface charge modification method using sandblasting. Additionally, we discuss insights on the important factors affecting effectiveness of surface-charge modification methods and point out several interesting directions for future investigations on this topic.

Comparison of biological characteristics of mesenchymal stem cells grown on two different titanium implant surfaces

This study examined the biological characteristics of mesenchymal stem cells (MSCs) grown on sand-blasted, large-grit, acid-etched (SLA) surface and hydroxyapatite (HA) coating on the SLA (HA/SLA) surface of titanium dental implants. The HA/SLA surfaces of titanium dental implants were formed by the ion beam assisted deposition (IBAD) method. Rabbit bone marrow derived mesenchymal stem cells cultured in vitro were seeded onto the surface of SLA and HA/SLA; the growth states of MSCs on the two samples were observed by a scanning electron microscope; the proliferation index, alkaline phosphatase (ALP) activity, osteocalcin (OCN) content of MSCs and mRNA relative expression level of osteopontin (opn) were compared between two groups. MSCs were found to be easier to adhere to the HA/SLA surface compared to the SLA surface. At the same time, the ALP activity and the OCN content of MSCs grown on the HA/SLA surface were obviously higher, and the relative expression level of opn mRNA was 4.78 times higher than that on the SLA surface. The HA coating formed by the IBAD method on the SLA surface of titanium dental implants significantly improves proliferation and well-differentiated osteoblastic phenotype of MSCs, which indicates a promising method for the surface modification of titanium dental implants.

Improvement of osseointegration of titanium dental implants by a modified sandblasting surface treatment: an in vivo interfacial biomechanics study.

To study the effects of a modified sandblasting surface treatment on the osseointegration of dental implants at the level of interfacial biomechanics, an in vivo pullout test was conducted using bone-interfacial shear strength as a criterion. Titanium implants were inserted into the medialis condyli of dogs and harvested 2, 4, and 12 weeks after insertion. Shear strength was determined with an Instron pullout tester. Observation and analysis of the surface of modified sandblasted implants after pullout at 12 weeks were performed with scanning electron microscopy and x-ray spectroscopy. Results showed that the shear strength of implants with a modified sandblasted surface was about five times as high as that of implants with a smooth surface. We concluded that the rough surface of titanium dental implants created by the modified sandblasting treatment can greatly enhance the shear strength at the dental implant-bone interface and that, with this enhancement, the secondary micropores play a much more important role in implant-bone bonding.