Supply Circuit Research Articles

Power Supply Circuit for Dual Operation in Producing Tokamak and Reversed Field Pinch Plasmas in RELAX

Power Supply Circuit for Dual Operation in Producing Tokamak and Reversed Field Pinch Plasmas in RELAX

Performance analysis of mono-stage three-phase DC-AC converter with reduced logic power supply circuits

This paper presents the performance analysis of a mono-stage three-phase DC-AC converter with reduced logic power supply circuits. The power DC-AC power converter of the proposed system is formed by arrangement of one inductor, two power switches, and one capacitor in an opener-like configuration to yield each leg of the inverter. During the inversion process, the number of capacitor elements that charges up (builds electrical energy) or discharges across the power switches will be equal to the number of inductors that discharges or builds up magnetic energy that terminates in between the power switches and vice versa. Under this condition, the proposed system, boosts and converts DC power to AC power and at the same time maintains energy balance in the system in one stage power conversion phenomenon unlike conventional power inverters. The logic power supply circuit used in the proposed system has fewer component counts and performs optical isolation unlike its conventional counterparts which have larger component counts and isolate by electromagnetic induction. The proposed system achieved the following results: lower and cheaper logic power supply circuits, simulated phase voltages of 327.8 V and 326.6 V and 329.8 V at THDs of 0.09879 %, 0.2569 % and 0.2905 % and average phase currents of 6.30A, 6.32A and 6.26A, respectively, and experimented: scaled down phase-A, B, and C average voltages of 66.95 V, 65.6 V and 68.93 V at phase angles of 0°, 120°, and -120° respectively. The performance analysis of the mono-stage three-phase DC-AC converter with reduced logic power supply circuits can be used in home appliances, hospital equipment, communication-based power stations, and drive systems such as electric vehicles.

Load characteristics of magnetization-dependent transverse thermoelectric generation in GdFeCo ferrimagnetic alloy thin films

We evaluated the thermoelectric voltage and electric power induced by the transverse and longitudinal thermoelectric generation, along with their load resistance characteristics, by measuring the load voltage in remanent magnetization states of a perpendicularly magnetized GdFeCo ferrimagnetic alloy thin film. Various load resistances were connected transversely and longitudinally to the temperature gradient. Our results showed that the load voltage induced by thermoelectric generation varied with load resistance. Additionally, the sign of the transverse load voltage reversed with the reversal of magnetization. The electric power generated thermoelectrically exhibited load dependency, reaching a local maximum. These behaviors can be qualitatively explained by the load characteristics of the power supply circuit, where polarity changes with the direction of remanent magnetization. In conclusion, we demonstrated the extraction of electric power via thermoelectric generation in a GdFeCo ferrimagnetic thin film. These observations suggest that using magnetic materials can provide new functionality for thermoelectric generators.

High-Frequency Magnetic Pulse Generator for Low-Intensity Transcranial Magnetic Stimulation

This paper presents a high-frequency (HF) magnetic pulse generator designed for low-intensity transcranial magnetic stimulation (LI-TMS) applications. HF pulse stimulation can induce a strong electric field with minimal current and enhance the penetration depth of the electric field in human tissue. The HF magnetic pulse generator was designed and fabricated using a microcontroller unit, gate driver, full-bridge coil driver, and stimulation coil. Measurements with a full-bridge circuit supply voltage of 10 V demonstrated an electric field intensity of 6.8 Vpp/m at a frequency of 1 MHz with a power dissipation of 2.45 W. Achieving a similar electric field intensity at a frequency of 100 kHz required approximately ten times the coil current. Additionally, a quasi-resonant LC load was introduced by connecting a capacitor in series with the stimulation coil, which set the resonant frequency to approximately 10% higher than the frequency of 1 MHz. This approach reduced the coil impedance, achieving higher current with the same bias supply voltage. Experimental results showed an enhanced electric field intensity of 19.1 Vpp/m with a supply voltage of only 1.8 V and reduced power dissipation of 1.11 W. The proposed HF pulse train with quasi-resonant coil system is expected to enable a low-power LI-TMS system.

An Overview of FPGA-inspired Obfuscation Techniques

Building and maintaining a silicon foundry is a costly endeavor that requires substantial financial investment. From this scenario, the semiconductor business has largely shifted to a fabless model where the Integrated Circuit (IC) supply chain is globalized but potentially untrusted. In recent years, several hardware obfuscation techniques have emerged to thwart hardware security threats related to untrusted IC fabrication. Reconfigurable-based obfuscation schemes have shown great promise of security against state-of-the-art attacks – these are techniques that rely on the transformation of static logic configurable elements such as Look Up Tables (LUTs). This survey provides a comprehensive analysis of reconfigurable-based obfuscation techniques, evaluating their overheads and enumerating their effectiveness against all known attacks. The techniques are also classified based on different factors, including the technology used, element type, and IP type. Additionally, we present a discussion on the advantages of reconfigurable-based obfuscation techniques when compared to Logic Locking techniques and the challenges associated with evaluating these techniques on hardware, primarily due to the lack of tapeouts. The survey’s findings are essential for researchers interested in hardware obfuscation and future trends in this area.

Classification of Multi-Source Partial Discharge in GIS

Abstract Partial discharge (PD) analysis is an important method to identify electrical equipment faults. However, due to the influence of environmental electromagnetic interference and other equipment discharges in the power supply circuit during the on-site PD test, the collected PD signal is the combination of various PD and noise, which makes it challenging to identify the type or source of on-site partial discharge. A multi-source PD classification method based on the multiple threshold and K-means clustering algorithm is pro-posed to solve this problem. First, wavelet transform with an improved threshold is used to initially denoise the original signal. Then the multiple threshold method is used to filter the residual ripple between every two pulses. Finally, spectrum analysis is carried out for each pulse, and the maximum value of the spectrum is extracted as the feature quantity. Then, the K-means algorithm is used to classify the PD pulses, and the PRPD images of PD pulses in different frequency domains are obtained. The results show that the method adopted in this paper can denoise, extract and classify the PD signals collected on the site, and the PRPD diagram of PD pulse after classification is more obvious, which provides a basis for identifying the PD source on the site.

Асинхронды генератордың статор орамасының белсенді кедергісі мен температурасын жанама түрде анықтау

The indirect methods for calculating the temperature of asynchronous generators with the introduction of a pulse component in the power supply circuit of the stator windings of asynchronous generators with squirrel-cage rotor are considered. The relevance of this is sue is determined by the need to improve asynchronous energy converters to increase their reliability and safety. An indirect method for determining temperature based on measuring the resistance of the stator of an asynchronous generator with squirrel-cage rotor is proposed. The method is based on superimposing pulse signals of small amplitude and high frequency of 600 Hz on an alternating mains sinusoidal voltage with a frequency of 50 Hz. There were given the simulation results. The research results confirm the possibility of indirect tempera ture determination and the creation of a thermal protection system for asynchronous energy converters based on the use of estimation methods.

Creation of an Information and Measuring Protection System against Arc and Partial Discharges in Complete Switchgears of Substations

In the article, the author considers the development and description of the principle of operation of an information and measuring protection system against arc and partial discharges in complete switchgears of electrical substations. The data acquisition by the information and measurement system is carried out on the basis of the acoustic method, followed by analysis and decision-making on disconnecting the power supply circuits when a pre-emergency condition of electrical equipment is detected. A block diagram of an information and measurement system and a schematic diagram of an acoustic sensor are presented. The criteria characterizing the technical condition of the control panel are defined. A method of protection against arc and partial discharges by recording and processing an acoustic signal is proposed.

Study of a Laboratory Circuit with a Warm Baseboard in Pulse Mode

The increasing global energy demand is a problem that people have been paying attention to, people's demand for energy is increasingly urgent, and improving energy efficiency has become a hot topic in this century. Studies have shown that pulsating flow has an important effect on heat transfer, and it has been concluded in most literatures that turbulent pulsation can enhance heat transfer in different degrees. Pulsation heat transfer is a comprehensive heat transfer process, and the best heat transfer performance can be achieved only when the thermal resistance of each part is reasonably coordinated. Based on the principle of hydraulic shock, this paper develops a device with warm substrate which can be used to increase the pulsating pressure and enhance the heat transfer efficiency of pulsating flow. Firstly, the construction scheme of the experimental device is proposed, and the working principle of the experimental device is described in detail. The complex impedance, frequency function, amplitude-frequency characteristic and phase-frequency characteristic are obtained by mathematical transformation of power supply circuit. Finally, the frequency response of the circuit is constructed.

Development of a Prototype Non-volatile Heating Circuit with Pulsating Mode

The emergence of global energy crisis makes energy saving technology become the key technology of sustainable development. Enhanced heat transfer technology can improve the efficiency of various heat transfer equipment and reduce the weight and volume, which plays a vital role in energy saving and sustainable economic development. In recent years, based on theoretical and experimental research, Chinese researchers and technicians have developed many new technologies to strengthen heat transfer, such as cross-scaled elliptic tube, discontinuous double-inclined inner rib tube, spiral groove tube, spiral groove tube, inner fin tube, twisted elliptic tube and so on. Among them, the pulsating heat transfer technology is an efficient and energy-saving means that can significantly strengthen the convective transport operation and improve the heat transfer effect. Through fluid pulsation or the vibration of the heat transfer pipe, the technology can remove the dirt deposited on the heat exchange surface, reduce the thermal resistance of the dirt, and improve the performance and life of the heat exchanger. It is widely used in the cooling of electronic components, automobile turbines, and the utilization of atomic energy in Marine environment. Firstly, the construction scheme of the experimental device is proposed, and the working principle of the experimental device is described in detail. The complex impedance, frequency function, amplitude-frequency characteristic and phase-frequency characteristic are obtained by mathematical transformation of power supply circuit. Finally, the frequency response of the circuit is constructed.

DC Power Boosting Circuit for Freestanding‐Sliding Triboelectric Nanogenerators with High Intrinsic Impedance and Multi‐Harmonic Output

AbstractThis study presents a freestanding sliding triboelectric nanogenerator (FS‐TENG) designed for low‐frequency motions (below 2 Hz). However, for practical applications, an efficient power management strategy is required to handle the harmonic outputs of the FS‐TENG. The high‐frequency signal is not sustainable for powering low‐power electronic applications. To address the issue, a novel direct current power supply circuit (DPS) is proposed that utilizes a double charge circuit (DCC) and a comb filtering circuit (CFC) to efficiently harness harmonic sources from the FS‐TENG. The direct power supply (DPS) outperforms traditional converters by reducing the impedance of the FS‐TENG and collecting the target harmonic sources, which facilitates a continuous power supply to the load. The results demonstrate that the DPS is capable of providing a continuous DC voltage of 2.2 V to a 10 MΩ load with minimal ripple (0.039%) at a low operating frequency of 0.625 Hz. Additionally, the practical application of a self‐powered temperature sensor is demonstrated to highlight the potential of FS‐TENG and DPS for low‐frequency energy harvesting solutions in real‐world scenarios.

Power-modulated reconfigurable nonlinear plasmonic devices without DC power supply and feed circuit

High-power electromagnetic (EM) waves can directly modulate the parameters of nonlinear varactor diodes through the rectification and Kerr effects without relying on external sources. Based on this principle, we propose a power-modulated reconfigurable nonlinear device based on spoof surface plasmon polariton (SSPP) waveguide loaded by varactor diodes, without applying DC power supply or feed circuit. Increasing the input power level reduces the effective capacitance of the varactor diode, leading to a blueshift in the cutoff frequency of the SSPP waveguide. This feature can be employed to realize the switching on/off of the input signal depending on the signal power. On the other hand, the transmission state of a low-power signal can be controlled by inputting another independent high-power EM wave simultaneously. Increasing the power of the control wave will enable the low-power signal within a wider bandwidth switched from off to on states. Experimental results are presented to show the excellent performance of the power-modulated reconfigurable SSPP device. This method can reduce the system complexity and provide inspiration for reconfigurable all-passive multifunctional devices and systems.

Design of a mining carbon monoxide sensor and analysis of multi-gas cross-interference performance

Abstract A new type of carbon monoxide sensor is designed to address the issue of cross interference of nitrogen oxide gas in the exhaust emissions of underground diesel engine rubber-tired vehicles with electrochemical carbon monoxide sensors, which leads to frequent false alarm accidents. The hardware circuit design of the DC-DC voltage reduction power supply circuit, display circuit, component signal processing circuit, etc. is detailed, At the same time, the sensitive components used in the sensor adopt a special gas filtration membrane design. Six types of gases, including hydrogen sulfide, nitric oxide, nitrogen dioxide, hydrogen, ethylene, and acetylene, were sequentially introduced in the laboratory for experimental analysis of multi-gas cross-interference performance. The experimental results have shown that the new carbon monoxide sensor can filter out nitrogen oxide gas, thereby solving the impact of underground rubber tire vehicle exhaust on the accuracy of carbon monoxide gas detection. It has broad prospects for promotion and application in coal mines underground.

87‐2: Modeling and Simulation for Mitigating Display Noise Caused by PMIC Ripple

The output ripple of the Power Management IC (PMIC) is one of the causes of display panel noise. This paper introduces modeling and simulation methods aimed at predicting and mitigating noise induced by PMIC ripple. If the display panel simulation is performed using an ideal voltage source, the ripple characteristics of the PMIC cannot be included. The improved method accurately predicted the ripple of the voltage input to the panel by modeling flicker noise and thermal noise, which are the main causes of PMIC noise, and modeling the Z‐parameter and decoupling capacitor of the PCB. In addition, it was possible to minimize ripples and finally reduce display noise by optimizing the design of the power supply circuit.

A Design and Construction of the Vibration Perception Threshold Measurement Device for Diabetes

A Design and Construction of the Vibration Perception Threshold Measurement Device for Diabetes

Indirect temperature protection of an asynchronous generator by stator winding resistance measurement with superimposition of high-frequency pulse signals

The article deals with the indirect methods for calculating the temperature of asynchronous generators with the introduction of a pulse component in the power supply circuit of the stator windings of asynchronous generators with squirrel-cage rotor. The relevance of this issue is determined by the need to improve asynchronous energy converters to increase their reliability and safety. The object of the study is an asynchronous generator with squirrel-cage rotor, which consume 40 % of the total electricity generated, and are the most affordable. One of the dangerous modes of asynchronous generators is their overheating as a result of increased currents and temperatures. The thermal protection of the stator winding of asynchronous generators relies primarily on measuring or determining the winding temperature. An indirect method for determining temperature based on measuring the resistance of the stator of an asynchronous generator with squirrel-cage rotor is proposed. The method is based on superimposing pulse signals of small amplitude and high frequency of 600 Hz on an alternating sinusoidal voltage with a frequency of 50 Hz. A simulation model for a 3 kW asynchronous generator has been developed. There were given the simulation results. The estimated values of the active resistances of the stator can be used to indirectly determine the temperature of the windings in thermal protection devices of asynchronous generators, as well as for control, monitoring and diagnostics of the technical condition. The research results confirm the possibility of indirect temperature determination and the creation of a thermal protection system for asynchronous energy converters based on the use of estimation methods.

COMMON-MODE AND DIFFERENTIAL CHOKES

The types of interference in power supplies and DC/DC converters are described. The principle of operation, parameters and design designs of common-mode and differential chokes are given. The features of filters used in power supply circuits and in signal interfaces are established. These data can be used to design commonmode chokes and electrical devices containing them.

Thermal Energy consumption monitoring System in the Hot water Supply circuit as part of the Smart Home management system

Thermal Energy consumption monitoring System in the Hot water Supply circuit as part of the Smart Home management system

Enhancing Preamplifier Design for Acoustic Emission Detection Instrument

With the development of the industry, the safety of pressure vessels is crucial for both production and personnel safety. The application of acoustic emission testing technology as a dynamic non-destructive testing method in the detection of pressure vessels is becoming increasingly prevalent. This paper presents the design of a low-frequency acoustic emission preamplifier with a frequency range of 30KHz to 200KHz and a gain of 20dB. The preamplifier is composed of amplification circuits, power supply circuits, and filtering components. By utilizing the PXR04 series high-sensitivity resonant acoustic emission sensor and Texas Instruments' OPA333 operational amplifier, along with a clever power supply design, effective signal amplification and system stability are ensured. Experimental results validate the correctness of the design, providing a feasible and effective solution for enhancing the performance of acoustic emission testing equipment.

An intelligent schedule maintenance method for hydrogen fuel cell vehicles based on deep reinforcement learning considering dynamic reliability

Schedule maintenance activities for hydrogen fuel cell vehicles are aimed to keep them in better condition in long-term operation. In this paper, we develop a reinforcement learning based schedule maintenance strategy, which is used to comprehensively consider the balance between safety and maintenance cost, so as to find the optimal maintenance strategy. A multi-level framework is established with remaining useful life of key components, fault tree analysis, and logistics cost model to generate an exploration environment that can express the operational stability, the failure rate of components, and the cost of repair and storage. The trained agent combines a deep neural network to explore the optimal strategy under the dynamic reliability of key components. Finite steps are the constraints. Safety rates, maintenance cost, and episode of operation are incorporated into a multi-objective reward function. The hydrogen supply circuit of fuel cell vehicle is simulated via Python. The trained agent is compared with traditional time-based schedule maintenance strategy and corrective maintenance strategy. The results show that the reinforcement learning based schedule maintenance agent has optimized the total reward, cost control and accident rate by 77%, 59% and 5%, respectively, compared with the traditional time-based schedule maintenance strategy. In the safe operation management of fuel cell vehicles, efficient and stable decision-making ability has been achieved.