Superconducting Nanowire Single-photon Detectors Research Articles

Evaluation of a-NbGe films as a candidate material for superconducting nanowire single-photon detector (SNSPD) applications

Evaluation of a-NbGe films as a candidate material for superconducting nanowire single-photon detector (SNSPD) applications

Sub-millikelvin-resolved superconducting nanowire single-photon detector operates with sub-pW infrared radiation power

Abstract The noise equivalent temperature difference (NETD) indicates the minimum temperature difference resolvable by an infrared detector. The lower the NETD is, the better the sensor can register small temperature differences. In this work, we proposed a strategy to achieve a high temperature resolution using a superconducting nanowire single-photon detector (SNSPD) with ultrahigh sensitivity. We deduced the model for calculating the NETD of a photon-counting type detector and applied it to our SNSPD-based setup. Experimentally, we obtained a NETD as low as 0.65 mK, which is limited by the background radiation of the environment, and the required infrared radiation power is calculated to be less than 1 pW. Furthermore, the intrinsic NETD of this SNSPD is estimated to be less than 0.1 mK. This work demonstrated a sub-mK temperature resolution with the SNSPD, paving the way for future remote infrared thermal imaging with high temperature resolution.

Monte Carlo calculations of cryogenic photodetector readout of scintillating GaAs for dark matter detection

The recent discovery that GaAs(Si,B) is a bright cryogenic scintillator with no apparent afterglow offers new opportunities for detecting rare, low-energy, electronic excitations from interacting dark matter. This paper presents Monte Carlo calculations of the scintillation photon detection efficiencies of optical cavities using three current cryogenic photodetector technologies. In order of photon detection efficiency these are: (1) Ge/TES: germanium absorbers that convert interacting photons to athermal phonons that are readout by transition edge sensors, (2) KID: kinetic induction detectors that respond to the breaking of cooper pairs by a change in resonance frequency, and (3) SNSPD: superconducting nanowire single photon detectors, where a photon briefly transitions a thin wire from superconducting to normal. The detection efficiencies depend strongly on the n-type GaAs absolute absorption coefficient KA, which is a part of the narrow beam absorption that has never been directly measured. However, the high cryogenic scintillation luminosity of GaAs(Si,B) sets an upper limit on KA of 0.03/cm. Using that value and properties published for Ge/TES, KID, and SNSPD photodetectors, this work calculates that those photodetectors attached to opposing faces of a 1 cm3 cubic GaAs(Si,B) crystal in an optical cavity with gold mirrors would have scintillation photon detection efficiencies of 35%, 25%, and 8%, respectively. Larger values would be expected for lower values of KA.

Room-temperature photonic quantum computing in integrated silicon photonics with germanium–silicon single-photon avalanche diodes

Most, if not all, photonic quantum computing (PQC) relies upon superconducting nanowire single-photon detectors (SNSPDs) typically based on niobium nitride (NbN) operated at a temperature <4 K. This paper proposes and analyzes 300 K waveguide-integrated germanium–silicon (GeSi) single-photon avalanche diodes (SPADs) based on the recently demonstrated normal-incidence GeSi SPADs operated at room temperature, and shows that their performance is competitive against that of NbN SNSPDs in a series of metrics for PQC with a reasonable time-gating window. These GeSi SPADs become photon-number-resolving avalanche diodes (PNRADs) by deploying a spatially-multiplexed M-fold-waveguide array of M GeSi SPADs. Using on-chip waveguided spontaneous four-wave mixing sources and waveguided field-programmable interferometer mesh circuits, together with the high-metric SPADs and PNRADs, high-performance quantum computing at room temperature is predicted for this PQC architecture.

Quantum thermodynamics with a single superconducting vortex.

We demonstrate complete control over dynamics of a single superconducting vortex in a nanostructure, which we coin the Single Vortex Box. Our device allows us to trap the vortex in a field-cooled aluminum nanosquare and expel it on demand with a nanosecond pulse of electrical current. Using the time-resolving nanothermometry we measure [Formula: see text] joules as the amount of the dissipated heat in the elementary process of the single-vortex expulsion. Our experiment enlightens the thermodynamics of the absorption process in the superconducting nanowire single-photon detectors, in which vortices are perceived to be essential for a formation of a detectable hotspot. The demonstrated opportunity to manipulate a single superconducting vortex reliably in a confined geometry comprises a proof of concept of a nanoscale nonvolatile memory cell with subnanosecond write and read operations, which offers compatibility with quantum processors based either on superconducting qubits or on rapid single-flux quantum circuits.

Using superconducting single photon detector to improve the coupling efficiency of multimode fibers in the telescope ranging system

The receiving system adopts the coupling manner of space beam and the multimode fiber among some space target laser ranging system. The fiber coupling efficiency can affect the number of echo photons and ranging accuracy, especially in lunar laser ranging, high orbit satellite laser ranging and space debris tracking. This article proposes a method utilizing the telescope pointing technique and a four-pixel superconducting nanowire single photon detector (SNSPDs) to measure coupling efficiency of multimode fiber. SNSPDs has the excellent performance with high detection efficiency, low dark count rate, and low recovery time. In the experiment, SNSPDs receives the changing signals caused by adjusting the offset angle of the telescope. The root mean square of deviation between measured results and theoretical calculations is 4.48%. The method is based on existing laser ranging systems and is suitable for scientific engineering verification of optical fibers already installed in the system and monitoring of system status.

Electrical trace analysis of superconducting nanowire photon-number-resolving detectors

We apply principal component analysis (PCA) to a set of electrical output signals from a commercially available superconducting nanowire single-photon detector (SNSPD) to investigate their photon-number-resolving capability. We find that the rising edge as well as the amplitude of the electrical signal have the most dependence on photon number. Accurately measuring the rising edge while simultaneously measuring the voltage of the pulse amplitude maximizes the photon-number resolution of SNSPDs. Using an optimal basis of principal components, we show unambiguous discrimination between one- and two-photon events, as well as partial resolution up to five photons. This expands the use case of SNSPDs to photon-counting experiments, without the need of detector multiplexing architectures. Published by the American Physical Society 2024

A wideband readout charge amplifier for superconducting nanowire single photon detector

A wideband readout charge amplifier for superconducting nanowire single photon detector

Mid-infrared superconducting nanowire single photon detector enhanced by overcoupled metasurfaces

Mid-infrared superconducting nanowire single photon detector enhanced by overcoupled metasurfaces

Optical bias and cryogenic laser readout of a multipixel superconducting nanowire single photon detector

Optical bias and cryogenic laser readout of a multipixel superconducting nanowire single photon detector

Cryogenic temperature 3D mapping via a distributed temperature sensor with centimeter resolution

We conduct 3D mapping of cryogenic temperatures via a Raman-based distributed temperature sensor, employing standard telecom single-mode fibers and polarization-independent superconducting nanowire single photon detectors (SNSPDs). By coiling a test fiber around various stages of a liquid helium cooled cryostat, our device demonstrates a lower temperature sensing limit of (48 ± 2) K, below the nitrogen boiling point. This achievement is made possible by the low dark count rates of SNSPDs, as validated by theoretical simulations. Furthermore, we utilize our device to map cryogenic temperatures on the 350 cm2 surface of a specially designed hollow cylindrical aluminum sample, accommodating approximately 2 m of standard single-mode optical fiber. During nitrogen cooling, we monitor the temporal evolution of the spatially dependent temperature gradient on the metallic sample with a temporal sampling down to one minute. Fiber-based distributed temperature sensing with centimetric spatial resolution can be effectively applied for 3D mapping at cryogenic temperatures of superconducting, quantum computing and aerospace instrumentation.

Frequency-domain multiplexing of SNSPDs with tunable superconducting resonators

This work culminates in a demonstration of an alternative frequency-domain multiplexing (FDM) scheme for superconducting nanowire single-photon detectors (SNSPDs) using the kinetic inductance parametric up-converter (KPUP) made out of NbTiN. There are multiple multiplexing architectures for SNSPDs that are already in use, but FDM could prove superior in applications where the operational bias currents are very low, especially for mid-infrared and far-infrared SNSPDs. Previous FDM schemes integrated the SNSPD within the resonator, while, in this work, we use an external resonator, which gives more flexibility to optimize the SNSPD architecture. The KPUP is a DC-biased superconducting λ/2 resonator that is sensitive to current perturbations. When coupled to an SNSPD, the KPUP can be used to read out current pulses on a few μA scale. The KPUP is made out of NbTiN, which has a large kinetic inductance and a high operating temperature. Meanwhile, the SNSPD is made from WSi, which is a popular material for broadband SNSPDs. A software-defined radio platform and a graphics processing unit are used to read out the KPUP and SNSPD array. Frequency-domain multiplexed SNSPDs have applications in astronomy, remote sensing, exoplanet science, dark matter detection, and quantum sensing.

Superconducting single-photon detector integrated in DBR with optical microconnector for MM or SM fiber

This paper presents the development of a superconducting nanowire single-photon detector (SNSPD) integrated into a distributed Bragg reflector (DBR) with a design center wavelength of 830 nm and a bandwidth of 200 nm. This SNSPD is made of a superconducting niobium nitride (NbN) thin film that is produced using plasma-enhanced atomic layer deposition. The DBR is made of 15 alternating layers of silicon nitride and silicon oxide that are produced through plasma-enhanced chemical vapor deposition. The reflection efficiency of the mirror is 90% at a wavelength of 830 nm. For sufficient optical coupling, an optical micro-connector optimized for multimode or single-mode optical fibers with a diameter of 128 μm was formed using two-photon polymerization techniques. The niobium nitride film was deposited onto the DBR surface in-situ in two separate reactors connected by a vacuum transfer. The in-situ technique of deposition of a superconducting niobium nitride film and a DBR has allowed achieving a system detection efficiency of 90% at a wavelength of 830 nm and a dark count rate of 10 s−1 at a temperature of 2.5 K. Additionally, the detector jitter was 50 ps.

Time delay calibration techniques for receiving arrays in SNSPD-based optical communication systems

Superconducting nanowire single photon detectors (SNSPDs) have attracted considerable attention in the field of free-space optical communications, especially for ultra-long-distance communications. Calibrating the inherent time delay in the optoelectronic circuit of SNSPD arrays is critical to enabling photon detection with high time accuracy. In this paper, we propose two methods for estimating the inherent timing error: Gaussian fitting calibration (GFC) and maximum-likelihood calibration (MLC). In particular, MLC estimates the timing error by taking into account the deadtime and jitter characteristics of SNSPD. Experimental results demonstrate the effectiveness of the proposed methods.

High-performance photon number resolving detectors for 850–950 nm wavelength range

Since their first demonstration in 2001 [Gol’tsman et al., Appl. Phys. Lett. 79, 705–707 (2001)], superconducting-nanowire single-photon detectors (SNSPDs) have witnessed two decades of great developments. SNSPDs are the detector of choice in most modern quantum optics experiments and are slowly finding their way into other photon-starved fields of optics. Until now, however, in nearly all experiments, SNSPDs were used as “binary” detectors, meaning that they could only distinguish between 0 and >=1 photons, and photon number information was lost. Recent research has demonstrated proof-of-principle photon-number resolution (PNR) SNSPDs counting 2–5 photons. The photon-number-resolving capability is highly demanded in various quantum-optics experiments, including Hong–Ou–Mandel interference, photonic quantum computing, quantum communication, and non-Gaussian quantum state preparation. In particular, PNR detectors at the wavelength range of 850–950 nm are of great interest due to the availability of high-quality semiconductor quantum dots (QDs) [Heindel et al., Adv. Opt. Photonics 15, 613–738 (2023)] and high-performance cesium-based quantum memories [Ma et al., J. Opt. 19, 043001 (2017)]. In this paper, we demonstrate NbTiN-based SNSPDs with >94% system detection efficiency, sub-11 ps timing jitter for one photon, and sub-7 ps for 2 photons. More importantly, our detectors resolve up to 7 photons using conventional cryogenic electric readout circuitry. Through theoretical analysis, we show that the PNR performance of demonstrated detectors can be further improved by enhancing the signal-to-noise ratio and bandwidth of our readout circuitry. Our results are promising for the future of optical quantum computing and quantum communication.

Speckle‐Insensitive Fractal Superconducting Nanowire Single‐Photon Detector Coupled with Multimode Optical Fiber

AbstractSpeckles are ubiquitous phenomena associated with multi‐spatial‐mode optics, which may reduce detection efficiency and induce modal noise if the photoresponse of the detector is polarization‐dependent. Thus far, they limit the performance of superconducting nanowire single‐photon detectors (SNSPDs) coupled with multimode optical fibers (MMF). To solve this problem, here, it is shown that SNSPDs patterned into the fractal geometry is insensitive to speckles and generates minimal modal noise that would otherwise be induced by the polarization‐dependent local device efficiency of the meander and spiral SNSPDs. Using this advantageous property of the fractal SNSPDs, system detection efficiency at the wavelength of 1530 nm and 42‐ps timing jitter is demonstrated when we couple a fractal SNSPD with 50‐micrometer‐core, step‐index MMF. This work not only demonstrates a scheme to achieving high system detection efficiency for MMF‐coupled SNSPDs that can be used in many applications, but also provides insight on how engineered nanostructures of photodetectors can reduce modal noise when detecting light from multiple spatial modes.

Simulation of a Pulsed Metastable Helium Lidar

Measurements of atmosphere density in the upper thermosphere and exosphere are of great significance for studying space–atmosphere interactions. However, the region from 200 km to 1000 km has been a blind area for traditional ground-based active remote sensing techniques due to the limitation of facilities and the paucity of neutral atmosphere. To fulfill this gap, the University of Science and Technology of China is developing a powerful metastable helium resonance fluorescent lidar incorporating a 2 m aperture telescope, a high-energy 1083 nm pulsed laser, as well as a superconducting nanowire single-photon detector (SNSPD) with high quantum efficiency and low dark noise. The system is described in detail in this work. To evaluate the performance of the lidar system, numerical simulation is implemented. The results show that metastable helium density measurements can be achieved with a relative error of less than 20% above 370 km in winter and less than 200% in 270–460 km in summer, demonstrating the feasibility of metastable helium lidar.

Monolithic integrated superconducting nanowire digital encoder

Superconducting digital circuits are promising technologies that can overcome bottlenecks in both classical and quantum computation due to their ultra-high operation speed and extremely low power dissipation. Superconducting nanowire cryotrons (nTrons) are emerging as one type of superconductor switching devices, offering advantages complementary to conventional Josephson junctions. Achieving monolithic integration of a reasonable number of nTrons into a functional digital circuit is a crucial step to extend its application. In this study, we constructed a monolithic integrated nTron-based binary encoder, which includes input fanout circuits, on-chip biasing, combinational logic routing and multi-gate nTrons. This represents a monolithic nTron digital circuit comprising 137 nTron gates, 424 resistors, 274 inductors, and 164 vias developed using a two-superconducting-layer fabrication process. The performance of this monolithic nTron encoder surpasses that of our previously demonstrated circuit with discrete nTron components. The maximum bias margin is 28% for the fanout circuit and 60% for the multi-gate nTron when using a signal generator, while the minimum timing jitter is 40 ps. The total power dissipation mainly from biasing resistors is 19.6 μW, making it more power efficient than RSFQ encoders. The encoder is then packaged and connected with a superconducting nanowire single-photon detector array for demonstrating its function of addressing pixel locations. Compared to the conventional readout, the nTron encoder shows a minimum readout error rate lower than 10−4 and reduces the readout RF lines from 15 to 4. The design and fabrication technologies could enrich integrated nTron digital circuits beyond current limits and promote their applications in classical and quantum systems.

Advances in Cryogenic Systems for the Superconducting Nanowire Single Photon Detector and Superconducting Quantum Computer

Advances in Cryogenic Systems for the Superconducting Nanowire Single Photon Detector and Superconducting Quantum Computer

Optimal Leveraging of a Gifford-McMahon Cryocooler’s Regenerative Cooling Power for SNSPD Applications

Superconducting nanowire single photon detectors (SNSPDs) offer unparalleled efficiency, minimal dark count rates, and picosecond jitter, making them ideal for single photon detector applications across the visible to mid-IR spectrum. A common cryogenic system used to reach these detectors’ optimal operating temperatures (>1 K) consists of Sumitomo’s compact RDK101 Gifford McMahon Cryocooler (GMC) running on an Zephyr air cooled compressor, coupled with a helium four (4He) adsorption stage. In this work, our aim is to provide measurements of the RDK101 GMC second stage regenerator tube cooling power at several locations along its length. We then characterise the performance of the adsorption cooler with heat loads applied to the regenerator tube. Our measurements demonstrate that heat loads of 1.2 W can be intercepted at the tube’s section near the GMC’s first cooling stage, with a negligible effect on the performance of the adsorption cooler. The thermal conductivity of yellow brass coaxial was characterised from 4 K to 40 K. Here we show that the heat load from 64 coaxial cable can be optimally intercepted with the defined regenerator cooling power. These results indicate that a 1024-pixel SNSPD array using a 32x32 row column multiplexing architecture could be successfully implemented in this cryogenic platform.