Sulfonic Acid Research Articles

Clean and efficient preparation of metallic bismuth from methane-sulfonate electrolyte in the membrane electrolysis cell

As a prevailing hydrometallurgical extraction system for bismuth sulfide concentrate, the acidic chloride solution has superior applicability to raw materials and high recovery ratio of metallic bismuth. Nevertheless, it has disadvantages of being easily volatile and strongly corrosive, as well as large energy consumption and poor deposition morphology during chloride electrolysis. Methane-sulfonic acid (MSA) solution is widely considered as the next generation of green hydrometallurgical system, due to its excellent physicochemical properties such as high metal salts solubility, low volatility, and biodegradability. In this study, membrane electrolysis technique was adopted based on the acidic bismuth methane-sulfonate leaching solution, and the influence of electrolyte composition, cathode current density (CCD), and temperature parameters on the bismuth conversion ratio (BCR) and deposition rate (BDR), techno-economic indicators and cathodic bismuth morphology were studied. The results show that the CCD affects the deposits morphology significantly, and the bismuth metal is partially dark and composed of loose ellipsoidal particles at high current density. Under the optimal conditions (70g/L Bi3+ ions, 5g/L Fe2+ ions, 110g/L MSA, 35 °C, 180A/m2), high-purity metallic bismuth (Bi 99.97%) with silver-white luster is obtained. The BCR and BDR are 9.43% and 0.46kg/(h·m2), respectively. The cathodic current efficiency (CCE) reaches over 98%, and specific energy consumption (SEC) is less than 715 kWh/t Bi. Compared with the traditional chloride system, the MSA-based membrane electrolysis medium has advantages of environmental friendliness, low occupational risks, low carbon and energy consumption, and can thus provide a sustainable green solution for bismuth hydrometallurgy.

Highly durable perfluorosulfonic acid proton exchange membrane by combining inorganic free radical scavengers and organic antioxidants

In this work, a new type of complex was constructed by coordinating quercetin (QC) with cerium (Ce) ions. This complex was introduced into perfluorosulfonic acid resin (PFSA) to fabricate a proton exchange membrane. The coordination process prevented the formation of ion cross-links between cerium and sulfonic acid groups in PFSA, thereby keeping proton conductivity and fuel cell performance of membrane samples at a high level. Due to the insolubility of quercetin in water, its coordination with cerium minimized cerium migration, providing long-lasting resistance to free radicals. The effects of additives on PFSA membrane properties were investigated by measuring IEC, water uptake, swelling ratio, and proton conductivity. Fenton degradation experiments and membrane electrode assembly performance tests was conducted simultaneously. The results demonstrated that compared to the addition of quercetin or cerium alone, the use of QC-Ce increased the proton conductivity by 23.70% after 24-h Fenton degradation and lowered fluoride release by 58.29%. Meanwhile, the PFSA/QC-Ce composite membrane samples maintained an open circuit voltage of 0.935 V and a maximum power density of 668.15 mW cm−2 after 96 h of open circuit voltage hold testing.

Smartphone-Based Rapid Quantitative Detection Platform with Imprinted Polymer for Pb (II) Detection in Real Samples

This paper reports the successful development and application of an efficient method for quantifying Pb2+ in aqueous samples using a smartphone-based colorimetric device with an imprinted polymer (IIP). The IIP was synthesized by modifying the previous study; using rhodizonate, 2-acrylamido-2-methylpropane sulfonic acid (AMPS), N,N′-methylenebisacrylamide (MBA), and potassium persulfate (KPS). The polymers were then characterized. An absorption study was performed to determine the optimal conditions for the smartphone-based colorimetric device processing. The device consists of a black box (10 × 10 × 10 cm), which was designed to ensure repeatability of the image acquisition. The methodology involved the use of a smartphone camera to capture images of IIP previously exposed at Pb2+ solutions with various concentrations, and color channel values were calculated (RGB, YMK HSVI). PLS multivariate regression was performed, and the optimum working range (0–10 mg L−1) was determined using seven principal components with a detection limit (LOD) of 0.215 mg L−1 and R2 = 0.998. The applicability of a colorimetric sensor in real samples showed a coefficient of variation (% RSD) of less than 9%, and inductively coupled plasma mass spectrometry (ICP-MS) was applied as the reference method. These results confirmed that the quantitation smartphone-based colorimetric sensor is a suitable analytical tool for reliable on-site Pb2+ monitoring.

Association between exposure to per- and polyfluoroalkyl substance and liver injury in American adults.

Epidemiological data is scarce regarding the association between exposure to mixtures of per- and polyfluoroalkyl substances (PFASs) and liver injury in the general populace. The current research used data from the National Health and Nutrition Examination Survey (2009-2018). The PFAS exposure levels were defined by the serum concentrations of PFASs with > 70% detection in samples, namely perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), perfluorohexane sulfonic acid (PFHxS), perfluorodecanoic acid (PFDeA), and perfluorooctane sulfonic acid (PFOS). Liver injury was assessed from two aspects: first, the degree of liver inflammation was determined based on serum alanine aminotransferase (ALT), aspartate aminotransferase (AST), glutamyltransferase (GGT), and total bilirubin (TBIL) levels; second, the degree of liver fibrosis was determined based on fibrosis-4 (FIB-4) index. We assessed the associations between individual or total PFAS exposure and these outcomes using multivariable linear regression models and logistic regression models, restricted cubic splines, and weighted quantile sum regression. Among the samples of 7484 American adults, the median concentration of PFOS was the highest, followed by PFOA and PFHxS. Using multivariable linear regression, a positive correlation was observed between all PFASs and liver enzymes such as ALT, AST, and TBIL. Additionally, the weighted quantile sum model indicated an overall positive association between the five PFASs and liver injury indicators. For liver function biomarkers and liver fibrosis, PFNA and PFOS were the most heavily weighting chemicals, respectively. Our findings provide new epidemiological evidence indicating a potential association between PFAS exposure and adverse effects on liver injury biomarkers, highlighting the potentially harmful effects of PFAS exposure on liver health.

Tungsten oxide embedded graphene oxide doped with SPEEK composite membrane for zinc–bromine redox flow batteries

Zinc-bromine redox flow batteries (Zn/Br2 RFBs) are fingerprint candidates for large-scale energy storage applications owing to their low cost, flexibility, high energy density, and astonishing round-trip efficiency. However, during the charging and discharging process, the diffusion of bromine through the porous membrane creates significant capacity decay and reduces the membrane efficiency of Zn/Br2 RFBs. In this respect, we developed various amounts of tungsten trioxide (WO3) nanoparticle-decorated graphene oxide (WO3@GO)-loaded sulfonated poly (ether ether ketone) (SPEEK) membranes and investigated their Zn/Br2 redox flow battery performance. The optimum amount of WO3@GO-loaded WO3@GO/SPEEK-3 membrane exhibits higher mechanical stability and ionic conductivity, significantly restricting the bromine crossover through the membrane. Due to their higher hydrophilic ability and uniform dispersion, WO3-loaded GO nanosheets provide strong interaction between the sulfonic acid group of the SPEEK membrane, which acts as an effective barrier for bromine crossover and significantly alters the Zn/Br2 battery performance. As a result, at a current density of 40 mA cm−2, the Zn/Br2 single cell of the WO3@GO/SPEEK-3 demonstrated higher coulombic efficiency (96.6 %), voltage efficiency (89.6 %), and energy efficiency (86.6 %), better than the WO3@GO/SPEEK-5 and pristine SPEEK membranes. These performances indicate that the proposed low-cost WO3@GO/SPEEK membrane can be highly applicable to other energy-related fields, including fuel cells and water treatment.

Abiotic formation of alkylsulfonic acids in interstellar analog ices and implications for their detection on Ryugu

For the last century, the source of sulfur in Earth’s very first organisms has remained a fundamental, unsolved enigma. While sulfates and their organic derivatives with sulfur in the S(+VI) oxidation state represent core nutrients in contemporary biochemistry, the limited bioavailability of sulfates during Earth’s early Archean period proposed that more soluble S(+IV) compounds served as the initial source of sulfur for the first terrestrial microorganisms. Here, we reveal via laboratory simulation experiments that the three simplest alkylsulfonic acids—water soluble organic S(+IV) compounds—can be efficiently produced in interstellar, sulfur-doped ices through interaction with galactic cosmic rays. This discovery opens a previously elusive path into the synthesis of vital astrobiological significance and untangles fundamental mechanisms of a facile preparation of sulfur-containing, biorelevant organics in extraterrestrial ices; these molecules can be eventually incorporated into comets and asteroids before their delivery and detection on Earth such as in the Murchison, Tagish Lake, and Allende meteorites along with the carbonaceous asteroid Ryugu.

Organic Mixed Ionic-Electronic Conductors Based on Tunable and Functional Poly(3,4-ethylenedioxythiophene) Copolymers.

Organic mixed ionic-electronic conductors (OMIECs) are being explored in applications such as bioelectronics, biosensors, energy conversion and storage, and optoelectronics. OMIECs are largely composed of conjugated polymers that couple ionic and electronic transport in their structure as well as synthetic flexibility. Despite extensive research, previous studies have mainly focused on either enhancing ion conduction or enabling synthetic modification. This limited the number of OMIECs that excel in both domains. Here, a series of OMIECs based on functionalized poly(3,4-ethylenedioxythiophene) (PEDOT) copolymers that combine efficient ion/electron transport with the versatility of post-functionalization were developed. EDOT monomers bearing sulfonic (EDOTS) and carboxylic acid (EDOTCOOH) groups were electrochemically copolymerized in different ratios on oxygen plasma-treated conductive substrates. The plasma treatment enabled the synthesis of copolymers containing high ratios of EDOTS (up to 68%), otherwise not possible with untreated substrates. This flexibility in synthesis resulted in the fabrication of copolymers with tunable properties in terms of conductivity (2-0.0019 S/cm) and ion/electron transport, for example, as revealed by their volumetric capacitances (122-11 F/cm3). The importance of the organic nature of the OMIECs that are amenable to synthetic modification was also demonstrated. EDOTCOOH was successfully post-functionalized without influencing the ionic and electronic transport of the copolymers. This opens a new way to tailor the properties of the OMIECs to specific applications, especially in the field of bioelectronics.

Adsorption of spray droplets reduced adsorption of dicamba spray droplets on leaves as droplet size increases

Abstract Off-target movement of growth regulator herbicides can cause severe injury to susceptible plants. Apart from not spraying on windy days or at excessive boom heights, making herbicide applications using nozzles that produce large droplets is the preferred method for reducing herbicide drift. Although large droplets maintain a higher velocity and are more likely to reach the leaf surface in windy conditions, their ability to remain on the leaf surface is poorly understood. Upon impact with the leaf surface, droplets may shatter, bounce, roll-off, or be retained on a leaf surface. We examined how different nozzles, pressures, and adjuvants impact spray droplet adsorption on the leaf surface of common lambsquarters and soybean. Plants were grown in a greenhouse and sprayed in a spray chamber. Three nozzles (XR, AIXR, and TTI) were evaluated at 138, 259, and 379 kPa. Dicamba (0.14 kg ae ha⁻¹) was applied alone and with methylated seed oil (MSO), a non-ionic surfactant, silicone-based adjuvant, crop oil concentrate, or a drift reduction adjuvant. A 1, 3, 6, 8-pyrene tetra sulfonic acid tetra sodium salt was added as a tracer. Dicamba spray droplet adsorption when using the XR nozzle, which produced the smallest spray droplets, was 1.75 times greater than when applied with the TTI nozzle with the largest spray droplets. Applying dicamba with MSO increased adsorption on leaf surfaces nearly four times the amount achieved without an adjuvant. The lowest application pressure (138 kPa) increased dicamba spray volume adsorbed more than 10% compared to the higher pressures 259 and 379 kPa. By understanding the impacts of these application parameters on dicamba spray droplet adsorption, applicators can select application parameters, equipment, and adjuvants that will maximize the amount of dicamba spray volume retained on the target leaf surface while minimizing dicamba spray drift.

Identifying novel mechanisms of per- and polyfluoroalkyl substance-induced hepatotoxicity using FRG humanized mice.

Per- and polyfluoroalkyl substances (PFAS) such as perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS) and perfluoro-2-methyl-3-oxahexanoic acid (GenX), the new replacement PFAS, are major environmental contaminants. In rodents, these PFAS induce several adverse effects on the liver, including increased proliferation, hepatomegaly, steatosis, hypercholesterolemia, nonalcoholic fatty liver disease and liver cancers. Activation of peroxisome proliferator receptor alpha by PFAS is considered the primary mechanism of action in rodent hepatocyte-induced proliferation. However, the human relevance of this mechanism is uncertain. We investigated human-relevant mechanisms of PFAS-induced adverse hepatic effects using FRG liver-chimeric humanized mice with livers repopulated with functional human hepatocytes. Male FRG humanized mice were treated with 0.067mg/L of PFOA, 0.145mg/L of PFOS, or 1mg/L of GenX in drinking water for 28days. PFOS caused a significant decrease in total serum cholesterol and LDL/VLDL, whereas GenX caused a significant elevation in LDL/VLDL with no change in total cholesterol and HDL. All three PFAS induced significant hepatocyte proliferation. RNA-sequencing with alignment to the human genome showed a total of 240, 162, and 619 differentially expressed genes after PFOA, PFOS, and GenX exposure, respectively. Upstream regulator analysis revealed that all three PFAS induced activation of p53 and inhibition of androgen receptor and NR1D1, a transcriptional repressor important in circadian rhythm. Further biochemical studies confirmed NR1D1 inhibition and in silico modeling indicated potential interaction of all three PFAS with the DNA-binding domain of NR1D1. In conclusion, our studies using FRG humanized mice have revealed new human-relevant molecular mechanisms of PFAS including their previously unknown effect on circadian rhythm.

Epoxy‐Based Carbon Fiber‐Reinforced Plastics Recycling via Solvolysis with Non‐Oxidizing Methanesulfonic Acid

AbstractThe urgent requirement for efficient recycling strategies in the wind energy industry prompted this study to explore the behavior of methanesulfonic acid (MSA) in the solvolysis of carbon fiber‐reinforced plastics (CFRP), as an alternative to standard solvents and acids. For the investigation, two layers of carbon fibers, infused with amine‐based epoxy through a vacuum‐assisted resin infusion process, were applied. The results showed that MSA was the most effective solvent for the solvolysis of CFRP, compared to other investigated common acids. The recycled products demonstrated satisfactory properties for both the matrix and fiber, which were comparable to those of the virgin materials.

Production of Alkylate Gasoline Using Methanesulfonic Acid as a Green Catalyst in the Presence of Real Refinery Hydrocarbon Mixtures

Production of Alkylate Gasoline Using Methanesulfonic Acid as a Green Catalyst in the Presence of Real Refinery Hydrocarbon Mixtures

Multifunctional Hydroxylamine‐O‐Sulfonic Acid as Additives for Highly Efficient and Stable Perovskite Solar Cells

Despite the rapid development of perovskite solar cells (PSCs), defects in the devices continue to impede further improvements in power conversion efficiency and operational stability. In this work, the use of hydroxylamine‐O‐sulfonic acid as a bifunctional molecule to enhance the performance of PSCs is described. Strong coordination exists between the sulfonic acid group and uncoordinated Pb2+ of perovskite, while the NH bond on amino group interacts with uncoordinated I−. Thus, due to the synergistic contribution of sulfonic acid group and amino groups, the high‐quality perovskite film with good crystallinity and low defect density is achieved. As a result, the optimal devices exhibit an enhanced efficiency of 23.33%, which is much higher than that of the control device (21.53%). Notably, the optimized target device exhibits excellent long‐term operational stability, retaining over 90% of its initial efficiency after 480 h at 65 °C, over 93% after a continuous illumination test for 650 h, and over 96% after nearly 1400 h of air storage. In contrast, the control device demonstrates poorer stability. In these results, it is suggested that selecting a dual‐functional additive is a promising approach to enhance efficiency and maintain stability in PSCs.

Superhydrophilic and underwater superoleophobic hydrogel-loaded fabrics for enhanced oil/water separation

Separating oil/water mixtures in highly acidic, alkaline, and saline environments poses a significant challenge. This study presents a method for preparing stable hydrogel-loaded nonwoven fabrics capable of separating oil/water mixtures in such harsh conditions. The double network (DN) hydrogel-loaded nonwoven fabrics were fabricated by combining the in-situ copolymerization of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) with acrylamide (AM) and the physical freeze-thaw treatment of polyvinyl alcohol (PVA). This DN hydrogel exhibits an extremely low swelling degree (equilibrium swelling ratio = 0.37 g/g) and imparts excellent hydrophilic and underwater oleophobic performance (underwater oil contact angle >150°) to the loaded nonwoven fabrics. Additionally, owing to the unique structure formed by the hydrogel on the fabric surface, it demonstrates outstanding resistance to acids, alkalis, and salts. The material enables efficient oil/water separation in H2SO4, NaOH, and seawater solutions. The hydrogel-loaded nonwoven fabrics achieved a high oil/water separation efficiency of over 99 %, a water flux of more than 40,000 L/(m2·h), and maintained high stability even after 100 cycles of operation.

Dual-Site Biomacromolecule Doped Poly(3, 4-Ethylenedioxythiophene) for Bosting Both Anticoagulant and Electrochemical Performances.

Poly(3, 4-ethylenedioxythiophene) (PEDOT) as a new generation of intelligent conductive polymers, is attracting much attention in the field of tissue engineering. However, its water dispersibility, conductivity, and biocompatibility are incompatible, which limit its further development. In this work, biocompatible electrode material of PEDOT doped with sodium sulfonated alginate (SS) which contains two functional groups of sulfonic acid and carboxylic acid per repeat unit of the macromolecule. The as dual-site doping strategy simultaneously boosts anticoagulant and electrochemical performances, for example, good hydrophilicity (water contact angle of 59.40°), well dispersibility (dispersion solution unstratified in 30 days), high conductivity (4.45 S m-1), and enhanced anticoagulant property (extended activated partial thrombin time value of 59.0 s), forming an adjustable PEDOT: biomacromolecule interface; this fills the technical gap of implantable bioelectronics in terms of coagulation and thrombosis risk. At the same time, the assembled all-in-one supercapacitor with anticoagulant properties is prepared by PEDOT: sodium sulfonated alginate as electrode material and sodium alginate hydrogel as electrolyte layer. The dual-site doping strategy provides a new opinion for the design and optimization of functional conductive polymers and its applications in implantable energy storage fields.

PVA/PANI-DBSA Nanomesh Tactile Sensor for Force Feedback

Touch serves as an important medium for human–environment interaction. The piezoresistive tactile sensor has attracted much attention due to its convenient technology, simple principle, and convenient signal acquisition and analysis. In this paper, conductive beads-on-string polyvinyl alcohol (PVA)/polyaniline doped with dodecyl benzene sulfonic acid (PANI-DBSA) nanofibers were fabricated via the electrospinning technique. Due to the special nanostructure of PVA-coated PANI-DBSA, the tactile sensor presented a wide measuring range of 12 Pa–121 kPa and appreciable sensitivity of 8.576 kPa−1 at 12 Pa~484 Pa. In addition, the response time and recovery time of the sensor were approximately 500 ms, demonstrating promising prospects in the field of tactile sensing for active upper limb prostheses.

Aegeline attenuates TNBS-induced colitis by suppressing the NFƙB-mediated NLRP3 inflammasome pathway in mice.

A chronic inflammatory condition of the intestine, ulcerative colitis (UC), is challenging to successfully manage once diagnosed. Currently, available medical therapies for UC exhibit minimal efficacy with unacceptable side effects, while inventive biological agents are expensive and yetnotwell accepted by patients. Discovering more effective and safer treatments to treat UC is therefore essential. One of the primary alkaloids found in Aegle marmelos, aegeline, has anti-inflammatory and antioxidant properties as well as being able to suppress severalpro-inflammatory cytokines responsible for inflammation. The study aimed to investigate the effectiveness of aegeline in alleviating 2,4,6-trinitrobenzene sulfonic acid (TNBS)-induced colitis through the NFƙB-mediated NLRP3 inflammasome pathway. Mice were randomly allocated into six groups, Normal control (NC), Model control (MC-TNBS, 2,4,6-trinitrobenzene sulfonic acid), STD (TNBS + sulfasalazine 100mg/kg), AG1, AG2, and AG3 (TNBS + aegeline 5, 10, 20mg/kg) respectively. Physical parameters such as a change in body weight, stool consistency, rectal bleeding, colon length, myeloperoxidase (MPO) levels and nitric oxide (NO) levels, and disease activity index (DAI) were assessed and supporting gene expression studies of various pro-inflammatory cytokines and enzymes were evaluated and histopathological changes observed. Administration of aegeline (10, 20mg/kg) was found to be effective in colon protection by lowering the disease activity score and myeloperoxidase level and improving other physical parameters. Aegeline in high dose significantly downregulated the gene expression of NFƙB, iNOS, COX-2, NLRP3, IL-1β, and IL-18, conferring great anti-inflammatory potential. Suggestive of the findings, aegeline reduced the damage to the colon by downregulating transcriptional genes and enzymes leading to inflammation and mitigated TNBS-induced colitis probably through the NFƙB-mediated NLRP3 inflammasome pathway.

Characterization and optimization of ultrasound assisted oxidative desulfurization of a model fuel using a novel magnetic deep eutectic solvent

ABSTRACT In various studies, researchers have utilised different solvents to extract sulfur compounds from the fuels. This paper introduces a novel magnetic deep eutectic solvent employed in the ultrasound-assisted oxidative desulfurisation of dibenzothiophene within a model fuel. The solvent, synthesised at 85°C by combining choline chloride, p-toluene sulfonic acid, and FeCl₃, underwent characterisation through Fourier transform-infrared, Vibrating-sample magnetometer, and Raman spectrometry. Exploration of the key parameters, including oxidant to model fuel volumetric fraction percentage (0.2–0.3), Iron (III) chloride to choline chloride mole fraction (0.1–0.3), and Magnetic deep eutectic solvent to model fuel volumetric fraction (0.2–0.3), was conducted to assess their impact on dibenzothiophene conversion rates. Employing response surface methodology based on central composite experimental design, optimal operational parameters for the ultrasound-assisted oxidative desulfurisation process were identified, resulting in a sulfur removal rate of 98.7%. The findings highlight the solvent sustained efficiency even at higher dibenzothiophene concentrations. Additionally, the solvent paramagnetic properties facilitated an expedited separation from the fuel, leading to the significantly reduced process times.

Enhancing the efficiency of polypyrrole-dodecylbenzene sulfonic acid in-tube solid-phase microextraction coating for analysis of nitrogen-containing pesticides in water environments

Background: With the growing use of nitrogen-containing pesticides in agriculture, their residues in the environment have raised significant public health concerns.Objective: This study aimed to develop a novel PPy-DBSA/IT-SPME coating to enhance the detection efficiency of polar nitrogen-containing pesticides in water matrices.Methods: The preparation conditions were optimized, including pyrrole concentration at 7.0 mol/L, DBSA concentration at 0.014 mol/L, oxidant concentration at 0.35 mol/L, and a coating cycle repeated 10 times. High-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was employed for detection.Results: The novel coating effectively adsorbed 19 different categories of polar nitrogen-containing pesticides, including sulfonylureas, triazolopyrimidines, diphenyl ether herbicides, benzoylurea insecticides, and phenylurea herbicides, with unadsorbed rates below 10%. The analytical method achieved an average recovery rate of 61.92% to 115.21%, with an RSD below 5.0%. Detection and quantification limits ranged from 0.012 to 0.524 μg/L and 0.127 to 5.243 μg/L, respectively.Conclusion: The developed method is green, efficient, simple, and cost-effective. It offers an environmentally friendly and user-friendly approach for the detection of polar nitrogen-containing pesticide residues, demonstrating good recovery and precision. This method holds potential for wide application in environmental monitoring and food safety.

Concentration-induced spontaneous polymerization of protic ionic liquids for efficient in situ adhesion

The advancement of contemporary adhesives is often limited by the balancing act between cohesion and interfacial adhesion strength. This study explores an approach to overcome this trade-off by utilizing the spontaneous polymerization of a protic ionic liquid-based monomer obtained through the neutralization of 2-acrylamide-2-methyl propane sulfonic acid and hydroxylamine. The initiator-free polymerization process is carried out through a gradual increase in monomer concentration in aqueous solutions caused by solvent evaporation upon heating, which results in the in-situ formation of a tough and thin adhesive layer with a highly entangled polymeric network and an intimate interface contact between the adhesive and substrate. The abundance of internal and external non-covalent interactions also contributes to both cohesion and interfacial adhesion. Consequently, the produced protic poly(ionic liquid)s exhibit considerable adhesion strength on a variety of substrates. This method also allows for the creation of advanced adhesive composites with electrical conductivity or visualized sensing functionality by incorporating commercially available fillers into the ionic liquid adhesive. This study provides a strategy for creating high-performance ionic liquid-based adhesives and highlights the importance of in-situ polymerization for constructing adhesive composites.

Structurally Tunable Graphitized Mesoporous Carbon for Enhancing the Accessibility and Durability of Cathode Pt‐Based Catalysts for Proton Exchange Membrane Fuel Cells

Low Pt utilization and intense carbon corrosion of cathode catalysts is a crucial issue for high‐efficiency proton exchange membrane fuel cells due to the highly demanded long‐term durability and less acquisition/application cost. Herein, structurally tunable graphitized mesoporous carbon (GMC) is obtained by direct high‐temperature pyrolysis and in situ‐controlled mesopore formation; the structure‐optimized GMC1300‐1800 exhibits a mesopore size of 7.54 nm and enhanced corrosion resistance. Functionalized GMC1300‐1800 is loaded with small‐sized Pt nanoparticles (NPs) (1.5 nm) uniformly by impregnation method to obtain Pt/GMC1300‐1800 and form an “internal platinum structure” to avoid sulfonic acid groups poisoning as well as ensure O2/proton accessibility. Hence, the electrochemically active surface area (ECSA) of Pt/GMC1300‐1800 reaches 106.1 m2 g−1Pt, while mass activity and specific activity at 0.9 V are 2.1 and 1.4 times those of commercial Pt/C, respectively. Notably, the ECSA decay is less than 17% for both 30 000 cycles’ accelerated durability tests (ADTs) of Pt attenuation and carbon attenuation. Accordingly, the optimized mesoporous structure of GMC1300‐1800 significantly decreases the coverage of sulfonic acid groups on Pt NPs, leading to the highest peak power density in the single‐cell test. Density functional theory calculations demonstrate the synergistic effect between graphitization and mesoporosity on enhancing the accessibility and durability of the catalysts.