Sulfide-based Solid Electrolytes Research Articles

Accelerated Li Penetration and Crack Propagation Due to Mechanical Degradation of Sulfide-Based Solid Electrolyte.

This work presents quantitative investigations into the relationships between lithium dendrite growth in the defects of Li6PS5Cl (LPSCl) solid electrolyte (SE), crack nucleation and propagation in the SE, and the associated mechanical forces driving these dendrites and cracks. Two different growth modes for lithium dendrites are identified by ex situ scanning electron microscopy (SEM) observation: longitudinal cracking inside pores in the SE and lateral penetration along boundaries of the SE particles. These in situ TEM tests reveal that concentrated Li plating in a nano-sized defect on the LPSCl surface will lead to the nucleation and propagation of cracks into the LPSCl under a stress much smaller than the expected mechanical strength of the LPSCl material. This unexpected mechanical degradation is caused by a reduction in the mechanical strength of LPSCl during electrochemical charge/discharge cycling, resulting from a disorder in the crystal structure of LPSCl as revealed by DFT simulations. Due to this mechanical degradation of LPSCl, the threshold force necessary to initiate crack growth is much lower than the previously expected force to drive dendrite growth.

Isotropic cell design enables low-pressure lithium metal solid-state batteries

Solid-state batteries that utilize sulfide-based solid-electrolytes, such as the argyrodite Li6PS5Cl, have become one of the most promising directions for next-generation energy storage. However, one remaining technical challenge for such materials has been the requirement of large pressures during operation. This challenge grows as the size of the cells increase as the pressure must be uniformly distributed over a larger-and-larger area. In this work, we introduce an isotropic cell design to pressurize the cell with perfect homogeneity, which is ensured by using a fluid pressurization medium. By achieving perfect homogeneity, the magnitude of the pressure necessary to stabilize the material is greatly reduced. Using such an isotropic cell design, lithium-metal solid-state pouch cells achieve remarkable extreme-fast-charging performance even at a low-pressure of only 2 MPa.

Microstructure-chemomechanics relations of polycrystalline cathodes in solid-state batteries

Lithium-nickel-manganese-cobalt-oxides (NMC) embedded in solid-electrolytes are being extensively applied as composite cathodes to match the high energy density of metallic anodes. During charge/discharge, the cathode composite often degrades through the evolution of micro-cracks within the grains, along the grain boundaries, and delamination at the particle-electrolyte interface. Experimental evidence has shown that regulating the morphology of grains and their crystallographic orientations is an effective way to relieve the volume-expansion-induced stresses and cracks, consequently stabilizing the electrochemical performance of the electrode. However, the interplay among the crystal orientation, grain morphology, and chemo-mechanical behavior has not been holistically studied. In that context, a thermodynamically consistent computational framework is developed to understand the role of microstructural modulation on the chemo-mechanical interactions of a polycrystalline NMC secondary particle embedded in a sulfide-based solid electrolyte. A phase-field fracture variable is employed to consider the initiation and propagation of cracks. A set of diffused phase-field parameters is adopted to define the transition of chemo-mechanical properties between the grains, grain boundaries, electrolyte, and particle-electrolyte interfaces. This modeling framework is implemented in the open-source finite element package MOOSE to solve three state variables: concentration, displacement, and phase-field damage parameter. A systematic parametric study is performed to explore the effects of aspect ratio, the crystal orientation of grains, and the interfacial fracture energy through the chemo-mechanical analysis of the composite electrode. The findings of this study offer predictive insights for designing solid-state batteries that provide stable performance with reduced fracture evolution.

The improvement of electrochemical performance by mixing InF3 in Li5.3PS4.3Cl1.7 solid electrolyte

All-solid-state batteries (ASSBs) employing solid electrolytes (SE) are currently gaining attention as next-generation energy storage devices. Solid electrolytes exhibit higher energy densities and operation across a wide temperature range than liquid electrolytes. The solid electrolyte acts as a separator, providing higher mechanical strength than polymer separators. This helps prevent cell deterioration and short circuit issues caused by lithium dendrite growth during charge – discharge cycles. Consequently, lithium metal, previously challenging to apply in conventional lithium-ion batteries, can be utilized as an anode electrode material. Sulfide-based solid electrolytes offer advantageous mechanical properties and high ionic conductivity. However, their narrow chemical/electrochemical stability window poses challenges. During the charging-discharging process of a battery with a lithium metal anode, a reduction decomposition reaction of the solid electrolyte occurs. On the other hand, Lithium Fluoride (LiF) exhibits low electronic conductivity due to a wide band gap but has a broad electrochemical stability window. In this study, we prepared a mixture of Li5.3PS4.3Cl1.7 with InF3 to generate an artificial solid electrolyte interphase (SEI) containing LiF. We confirmed the structural properties using powder X-ray diffraction (XRD). The XRD pattern showed the maintenance of the argyrodite structure, with only an increase in the peak intensity corresponding to InF3. The optimized solid electrolyte-based ASSB demonstrated a higher initial discharge capacity of 172.8 mAh/g, a coulombic efficiency of 78.54 %, and a capacity retention rate of 93.6 %, outperforming ASSBs based on the bare solid electrolyte (Li5.3PS4.3Cl1.7).

Insights into Lithium Sulfide Glass Electrolyte Structures and Ionic Conductivity via Machine Learning Force Field Simulations.

Sulfide-based solid electrolytes (SEs) are important for advancing all-solid-state batteries (ASSBs), primarily due to their high ionic conductivities and robust mechanical stability. Glassy SEs (GSEs) comprising mixed Si and P glass formers are particularly promising for their synthesis process and their ability to prevent lithium dendrite growth. However, to date, the complexity of their glassy structures hinders a complete understanding of the relationships between their structures and properties. This study introduces a new machine learning force field (ML-FF) tailored for lithium sulfide-based GSEs, enabling the exploration of their structural characteristics, mechanical properties, and lithium ionic conductivities. Using molecular dynamic (MD) simulations with this ML-FF, we explore the glass structures in varying compositions, including binary Li2S-SiS2 and Li2S-P2S5 as well as ternary Li2S-SiS2-P2S5. Our simulations yielded consistent results in terms of density, elastic modulus, radial distribution functions, and neutron structure factors compared to DFT and experimental work. Our findings reveal distinct local environments for Si and P within these glasses, with most Si atoms in edge-sharing configurations in Li2S-SiS2 and a mix of corner- and edge-sharing tetrahedra in the ternary Li2S-SiS2-P2S5 composition. For lithium ionic conductivity at 300 K, the 50Li2S-50SiS2 glass displayed the lowest conductivity at 2.1 mS/cm, while the 75Li2S-25P2S5 composition exhibited the highest conductivity at 3.6 mS/cm. The ternary glass showed a conductivity of 2.6 mS/cm, sitting between the two. Moreover, an in-depth analysis of lithium ion diffusion over the MD trajectory in the ternary glass demonstrated a significant correlation between diffusion pathways and the rotational dynamics of nearby SiS4 or PS4 tetrahedra. The ML-FF developed in this study provides an important tool for exploring a broad spectrum of solid-state and mixed former sulfide-based electrolytes.

Cost-effective synthesis of sulfide-based solid electrolytes without using Li2S

Solid electrolytes possess highly attractive potential which can improve safety properties and achieve high energy density when they replace the conventional liquid electrolytes in Li-ion batteries. Sulfide-based solid electrolytes have received considerable attention owing to their high ionic conductivities and good wettability due to their soft nature. These materials are typically synthesized using Li2S as a precursor. However, Li2S is expensive and thus cannot be widely used to prepare sulfide-based solid electrolytes for all-solid-state batteries (ASSBs). Here, we propose a novel approach to synthesize a sulfide-based solid electrolyte without using Li2S as a precursor. In this method, the starting powders of Li2O, Mg, and S were converted into Li2S and MgO by ball milling. The Li2S-MgO composite was then sequentially milled with P2S5 and LiBH4, and a BH4-substituted thiophosphate solid electrolyte was synthesized. The resulting Li3PS4-LiBH4-MgO composite exhibited a high ionic conductivity of 7.2 mS cm–1 at 25 °C, and the ASSB prepared using the solid electrolyte functioned well. The thiophosphate local structure of the prepared samples was examined by Raman and 31P solid-state nuclear magnetic resonance spectroscopies. Although the ionic conductivity slightly decreased upon MgO addition, the thiophosphate local structure was maintained. Moreover, the presence of MgO improved the chemical stability of the electrolyte in air.

Synthesis and Comprehensive Analytical Study of β-Li3PS4 Stabilization by Ca- and Ba-Codoped Li3PS4.

Sulfide-based solid electrolytes with high Li+ conductivity, such as Li3PS4, are key materials for the realization of all-solid-state Li+ batteries. One approach to achieving high Li+ conductivity is to combine crystalline-phase stabilization at high temperatures with the introduction of defects at room temperature. In this work, this approach was verified by codoping Li3PS4 with two kinds of divalent cations. The resulting structural changes were comprehensively investigated both experimentally and computationally. The high-temperature β-Li3PS4 phase of Li3PS4 could be stabilized at room temperature by adjusting the amount of Ca or Ba doping. The synthesized samples doped with divalent cations were found to have conductivities about 2 orders of magnitude higher than that of the γ-Li3PS4 phase at room temperature. The resultant Li+ conductivity at room temperature was also higher than that expected from interpolation of results for nondoped β-Li3PS4. It is believed that the structural changes produced by the divalent cation doping contribute to this increase in conductivity. The stability of the β-Li3PS4 phase with divalent cation doping was also demonstrated using density-functional-theory calculations for models with equivalent compositions to the synthesized samples. The Li+ positions obtained by structural optimization calculations showed the presence of diverse and disordered Li sites in the Ca-doped lattice. Such structural changes can contribute to cascade processes involving Li+ collisions, referred to as the "billiard-ball" mechanism, which cannot occur in nondoped β-Li3PS4. This series of experiments involving the synthesis and analyses of β-Li3PS4 with divalent cation doping provides a way to enhance Li+ conductivity through structural modification and optimization.

Binderless Sheet-Type Oxide-Sulfide Composite Solid Electrolyte for All-Solid-State Batteries

Lithium-ion batteries have been used as energy sources not only for small electronic devices but also for high-capacity and high-energy-density applications such as electric vehicles. However, the use of flammable organic liquid electrolytes in lithium-ion batteries has raised safety concerns in various applications. Therefore, solid-state batteries using flame-retardant inorganic materials are considered a more reasonable direction for future energy sources due to their high safety and high energy density. Solid electrolytes(SEs) are divided into oxide-based, sulfide-based, and polymer-based. Each solid electrolyte has its own advantages and disadvantages. Oxide-based solid electrolytes (e.g., Li7La3Zr2O12 (LLZO), Li3xLa2/3-xTiO3 (LLTO), Li1.3Al0.3Ti1.7(PO4)3 (LATP)) are air-stable and exhibit excellent electrochemical properties over a wide potential range. However, their high interfacial resistance may limit their practical application as batteries. Sulfide-based solid electrolytes (e.g., Li6PS5X (X=Cl, Br, I), Li10GeP2S12, (100-x)Li2S-xP2S5)) have high ionic conductivity, ductile properties, low interfacial resistance, and good room temperature workability. However, they are vulnerable to atmospheric instability, which can produce toxic gases such as H2S, and are relatively electrochemically unstable with Li metal. Polymer-based solid electrolytes, such as those made from polymers like PEO, PVDF, PAN, etc. that are compounded with other solid electrolytes (oxides, sulfides, etc.), offer the advantage of being able to form solid electrolyte membranes over large areas. But they have low ionic conductivity and weak mechanical properties of the polymer itself, limiting their practical application. To apply solid-state batteries to practical high-energy density energy storage devices such as electric vehicles, high ion conductivity, electrochemical stability, high mechanical properties, and large area formation of the electrolyte layer are essential. Solid electrolytes are mainly formed in powder form, and without a polymer binder, it is limited to apply as a film for large-capacity storage devices. Here, we fabricated a freestanding sheet-type Al-LLZO oxide-based solid electrolyte that forms a 3D network without a polymer material using an electrospinning method. In addition, we prepared a oxide-sulfide composite solid electrolyte membrane by impregnating LPSCl sulfide-based solid electrolyte into the Al-LLZO solid electrolyte sheet. As a result, This process removed the polymer and improved both the ionic conductivity and mechanical properties. Furthermore, it was possible to achieve both large-area and film characteristics without the need for a polymer.

(Invited) Strategies for Enhancing the Stability of the Electrode-Electrolyte Interphase in Sulfide-Based Solid-State Batteries

In recent years, all solid-state batteries (SSBs) have gained significant attention as the next-generation energy storage device due to their high energy density, improved safety, and enhanced stability. Sulfide-based solid electrolytes (SEs) have garnered significant attention among various inorganic materials for their exceptional properties, including high ionic conductivity and robust mechanical properties. These features make them promising candidates for SSBs, ensuring both manufacturability and long-term cycle life. For example, Li-argyrodites (e.g., Li6PS5X, and X = Cl, Br, I) and Na-thioantimonate (e.g., Na2.88Sb0.88W0.12S4) offer high ionic conductivities (> 10-3 S/cm) that are comparable to those of liquid electrolytes. However, its practical application is still under-achieved due to a few technical challenges. Among the various issues, our focus is on the electrode-electrolyte interphase, which degrades the cycle life of the SSBs.At the cathode-electrolyte interphase, narrow electrochemical window (1.71 V – 2.01 V) of Li6PS5X unwantedly prompt the oxidative decomposition of solid-electrolyte. At the anode-electrolyte interphase, Li-argyrodite SEs can be easily reduced by Li metal or oxidized by cathode active materials because of its narrow electrochemical window (1.71 V – 2.01 V). The resulting byproducts at electrode-electrolyte interphases can unwantedly lead to capacity fading and an increase in cell resistance. Additionally, SSBs made with the Li-argyrodite SEs suffer from Li-dendrite penetration during repeated cycles and consequent internal short circuits.To address these challenges, we propose strategies for passivating the interphases between the cathode and the solid electrolyte, as well as between the metallic anode and the electrolyte in solid-state batteries (SSBs). Through a combinatorial study, we aim to elucidate the extent and severity of interfacial side reactions in solid-state batteries (SSBs). In addition, the optimal coating strategies of LiNbO3 for cathodes and Li3N coating on metallic Li anode will be discussed. The optimized Li3N as an artificial solid electrolyte interphase (SEI) layer on the metallic Li anode enables more than 5000 cycles without failure in symmetrical cells.Furthermore, we will also highlight a strategy for passivating the electrode-electrolyte interphases of Na-based solid-state batteries (SSBs) that employ thioantimoniate as the electrolyte material. The approaches to passivate the cathode and metallic Na anode will be presented. Comprehensive electrochemical and spectroscopic studies will be conducted to identify the source of degradation and elucidate the improvement mechanisms associated with each strategy.

Basicity and Stability of Argyrodite Sulfide-Based Solid Electrolytes

Argyrodite-type sulfide-based solid electrolyte Li6PS5Cl (LPSC) holds immense promise for solid-state battery applications. This is attributed to its stable structure and high ionic conductivity. Nonetheless, the persistent challenges involving the instability at the electrode/electrolyte interface and susceptibility to moisture present significant obstacles in material preparation and cell manufacturing processes. Our research has unveiled a noteworthy finding: the sulfur of the PS4 3− moiety is a Lewis-base active site to adsorb Lewis acid. It is found that the adsorption of CO2 on the sulfide electrolytes can enhance both the interfacial and electrochemical stability of the lithium and sulfide electrolyte interface. The formation of new S–CO2 bonds, confirmed using various analytical techniques, plays a pivotal role in modifying the interfacial behaviors of the sulfide electrolytes. Moreover, the LijCO2@LPSCjLTO shows an amazing result, with 62% capacity retention and ultra-high coulombic efficiency of 99.91% after 1000 cycles. Interestingly, the same concept was also applied to the high ionic conductivity sulfide-based superionic conductor Li10GeP2S12 (LGPS) system, which also has the PS4 3− moiety. A novel approach is also developed by utilization of the BBr3 gas as a Lewis base indicator to probe the strength of Lewis basicity of the sulfur sites of sulfide electrolytes. The basicity of the sulfide electrolytes can be correlated to the shift of 11B NMR peak. This correlation is further supported by the H2S generation rate when the electrolyte is exposed to a moisture atmosphere. This work not only provides a new pave towards enhancing stability at the sulfide electrolyte/lithium interface but profound insights into the basicity and moisture stability of sulfide electrolytes.

Investigating the Mechanisms of Li Dendrite Formation in Sulfide Solid Electrolytes for All-Solid-State Batteries

As the primary use of Li-ion batteries shifts from small electronic devices to electric vehicles, there is a need to increase the stability and energy density of Li-ion batteries. In order to achieve high energy density, use of lithium metal as an anode has being considered due to its high theoretical capacity (3860 mAh g-1) and low reduction potential (-3.04 V vs. SHE). However, the liquid electrolyte used in Li-ion batteries is not only dangerous due to the risk of fire in case of leakage, but also has the disadvantage of shortening the lifetime of the battery due to the generation of lithium dendrites during cycling when lithium metal is used as anode. To overcome these disadvantages, all-solid-state batteries using solid electrolytes have emerged, which are expected to improve safety and cycling stability even when using lithium metal anodes. Among the various types of solid electrolytes, sulfide solid electrolytes are widely used due to their high ionic conductivity and ductility, which allows easy formation of good interfaces, resulting in high performance all-solid-state batteries.To date, many attempts have been made to use lithium metal anodes with solid electrolytes, but dendrite growth has not been completely suppressed.1 Dendrite growth is affected by many interface-related factors, such as void ratio, grain size, elastic modulus, reductive decomposition products, and electrical conductivity of the electrolyte, which must be clarified before the use of lithium metal anodes can be realized.2 It is essential to observe and analyse the changes during electrochemical tests in order to reveal the formation of Li dendrites under the conditions in which actual real cells operate. We have attempted to elucidate the dynamic structural changes at the interface using multimodal/multiscale operando X-ray CT under an applied pressure, as well as the reactions taking place at the interface by observing the interface products using X-ray absorption spectroscopy. In this study, X-ray diffraction, X-ray absorption spectroscopy, time-resolved impedance measurements and multi scale operando X-ray CT are used to determine the electrochemical and chemical mechanisms of Li dendrite formation in different sulfide solid electrolytes. By investigating and comparing the particle size, porosity, doping effect of halides and reduction resistance of solid electrolytes used in lithium metal solid-state batteries, the mechanism of Li dendrite growth and how each factor affects dendrite growth are investigated.Here, we discuss Li3PS4, halogen-doped Li3PS4, and argyrodite-based Li6PS5Cl as typical sulfide-based solid electrolytes; Li3PS4 is known to have a low elastic modulus, and a simple cold press could be used to reduce the inter-particle voids. However, Li3PS4 has a very narrow potential difference, which resulted in unwanted oxidation and reduction byproducts during battery cycling. The high electronic conductivity of the reduction products at the interface also led to the formation of electronic pathways, resulting in the concentration of current in several locations and ultimately triggering the formation of Li dendrites. On the other hand, in argyrodite Li6PS5Cl, the formation of an interfacial phase with low electronic conductivity, which is mainly composed of lithium chloride at the interface, suppresses the reduction reaction and thus the formation of Li dendrites. In the presentation, the relationship between the lithium dendrite formation and the operating conditions such as temperature and pressure will also be presented.

PVDF-HFP via Localized Iodization as Interface Layer for All-Solid-State Lithium Batteries with Li6PS5Cl Films.

All-solid lithium (Li) metal batteries (ASSLBs) with sulfide-based solid electrolyte (SEs) films exhibit excellent electrochemical performance, rendering them capable of satisfying the growing demand for energy storage systems. However, challenges persist in the application of SEs film owing to their reactivity with Li metal and uncontrolled formation of lithium dendrites. In this study, iodine-doped poly(vinylidenefluoride-hexafluoropropylene) (PVDF-HFP) as an interlayer (PHI) to establish a stable interphase between Li metal and Li6PS5Cl (LPSCl) films is investigated. The release of I ions and PVDF-HFP produces LiI and LiF, effectively suppressing lithium dendrite growth. Density functional theory calculations show that the synthesized interlayer layer exhibits high interfacial energy. Results show that the PHI@Li/LPSCl film/PHI@Li symmetrical cells can cycle for more than 650h at 0.1mA cm-2. The PHI@Li/LPSCl film/NCM622 cell exhibits a distinct enhancement in capacity retention of ≈26% when using LiNi0.6Mn0.2Co0.2O2 (NCM622) as the cathode, compared to pristine Li metal as the anode. This study presents a feasible method for producing next-generation dendrite-free SEs films, promoting their practical use in ASSLBs.

Enhanced Electrochemical Stability and Extended Cycle Life in Sulfide-Based All-Solid-State Batteries: The Role of Li10 SnP2 S12 Coating on Ni-Rich NCM Cathode.

Recently, sulfide-based all-solid-state batteries (ASSBs) have attracted great attention because of their excellent safety and high energy density. However, by-products formed from side-reactions between the oxide-based cathodes and sulfide-based solid electrolytes (SEs) increase the interfacial resistance and degrade the cell performance. Suppression of this interfacial resistance is thus critical. In this study, the extraordinarily high stability of the cathode/SE interface is discovered when a Li10 SnP2 S12 (LSnPS) is applied to a cathode buffer layer. The electrochemical properties of the cathode interface at high potential are improved by synthesizing a core-shell structure cathode using LSnPS. The synthesized LSnPS is uniformly coated on a Li2 ZrO3 -coated LiNi0.8 Co0.1 Mn0.1 O2 (LZO-NCM) surface using the cost-efficient mechano-fusion method. The ASSB with LSnPS-coated LZO-NCM as the cathode and Li6 PS5 Cl (argyrodite, LPSCl) as the SE exhibited a capacity of 192 mAh g-1 and excellent cycle retention of ≈75% after 500 charge/discharge cycles. In addition, the degradation mechanism at the cathode/SE interface is investigated. The results indicated that LSnPS stabilizes the interface between NCM and argyrodite, thereby inhibiting the decomposition of the SE. This technology is expected to contribute to the commercialization of cathode materials for sulfide-based ASSBs due to its enhanced cycle performance, low-cost material application, and eco-friendly process.

Synthesis and Characterization of Na3SbS4 Solid Electrolytes via Mechanochemical and Sintered Solid-State Reactions: A Comparative Study

A sulfide-based solid electrolyte is an enticing non-organic solid-state electrolyte developed under ambient conditions. Na3SbS4, a profoundly enduring substance capable of withstanding exceedingly elevated temperatures and pressures, emerges as a focal point. Within this investigation, we employ dual distinct techniques to fabricate Na3SbS4, encompassing ball milling and the combination of ball milling with sintering procedures. A remarkable ionic conductivity of 3.1 × 10−4 S/cm at room temperature (RT), coupled with a meager activation energy of 0.21 eV, is achieved through a bifurcated process, which is attributed to the presence of tetragonal Na3SbS4 (t-NSS). Furthermore, we delve into the electrochemical performance and cyclic longevity of the Na2/3Fe1/2Mn1/2O2|t-NSS|Na system within ambient environs. It reveals 160 mAh/g initial charge and 106 mAh/g discharge capacities at 0.01 A/g current density. Furthermore, a cycle life test conducted at 0.01 A/g over 30 cycles demonstrates stable and reliable performance. The capacity retention further highlights its enduring energy storage capabilities. This study underscores the sustainable potential of Na3SbS4 as a solid-state electrolyte for advanced energy storage systems.

Flexible and thin sulfide-based solid electrolyte sheet with Li+-ion conductive polymer network for all-solid-state lithium-ion batteries

All-solid-state lithium batteries (ASSLBs) with solid electrolytes are promising battery systems capable of improving the safety and energy density of current lithium-ion batteries. Reducing the thickness of the solid electrolyte while preventing the short circuit between the anode and cathode is imperative to increase the energy density of ASSLBs. Sulfide-based solid electrolytes have high ionic conductivities; however, they are brittle, difficult to be processed into a thin film, and challenging to form stable interfaces with electrodes of large volume change. In this study, flexible thin-solid electrolyte sheets with Li+-ion conductive polymer network were prepared and characterized for ASSLB applications. They exhibited higher ionic conductance and superior mechanical properties than those of pristine Li6PS5X (argyrodite) pellets. The all-solid-state lithium-ion cell (graphite/LiNi0.7Co0.15Mn0.15O2) with a solid electrolyte sheet delivered a high discharge capacity of 182.5 mAh g−1 and showed good cycling stability at 0.33 C and 25 ℃, demonstrating that flexible and thin sheets are promising solid electrolytes for ASSLBs operating at room temperature.

Trimethylsilyl Compounds for the Interfacial Stabilization of Thiophosphate-Based Solid Electrolytes in All-Solid-State Batteries.

Argyrodite-type Li6 PS5 Cl (LPSCl) has attracted much attention as a solid electrolyte for all-solid-state batteries (ASSBs) because of its high ionic conductivity and good mechanical flexibility. LPSCl, however, has challenges of translating research into practical applications, such as irreversible electrochemical degradation at the interface between LPSCl and cathode materials. Even for Li-ion batteries (LIBs), liquid electrolytes have the same issue as electrolyte decomposition due to interfacial instability. Nonetheless, current LIBs are successfully commercialized because functional electrolyte additives give rise to the formation of stable cathode-electrolyte interphase (CEI) and solid-electrolyte interphase (SEI) layers, leading to supplementing the interfacial stability between electrolyte and electrode. Herein, inspired by the role of electrolyte additives for LIBs, trimethylsilyl compounds are introduced as solid electrolyte additives for improving the interfacial stability between sulfide-based solid electrolytes and cathode materials. 2-(Trimethylsilyl)ethanethiol (TMS-SH), a solid electrolyte additive, is oxidatively decomposed during charge, forming a stable CEI layer. As a result, the CEI layer derived from TMS-SH suppresses the interfacial degradation between LPSCl and LiCoO2 , thereby leading to the excellent electrochemical performance of Li | LPSCl | LiCoO2 , such as superior cycle life over 2000 cycles (85.0% of capacity retention after 2000 cycles).

Transforming Li3PS4 Via Halide Incorporation: a Path to Improved Ionic Conductivity and Stability in All‐Solid‐State Batteries

AbstractTo enhance Li+ transport in all‐solid‐state batteries (ASSBs), harnessing localized nanoscale disorder can be instrumental, especially in sulfide‐based solid electrolytes (SEs). In this investigation, the transformation of the model SE, Li3PS4, is delved into via the introduction of LiBr. 31P nuclear magnetic resonance (NMR)unveils the emergence of a glassy PS43− network interspersed with Br−. 6Li NMR corroborates swift Li+ migration between PS43− and Br−, with increased Li+ mobility indicated by NMR relaxation measurements. A more than fourfold enhancement in ionic conductivity is observed upon LiBr incorporation into Li3PS4. Moreover, a notable decrease in activation energy underscores the pivotal role of Br− incorporation within the anionic lattice, effectively reducing the energy barrier for ion conduction and transitioning Li+ transport dimensionality from 2D to 3D. The compatibility of Li3PS4 with Li metal is improved through LiBr incorporation, alongside an increase in critical current density from 0.34 to 0.50 mA cm−2, while preserving the electrochemical stability window. ASSBs with 3Li3PS4:LiBr as the SE showcase robust high‐rate and long‐term cycling performance. These findings collectively indicate the potential of lithium halide incorporation as a promising avenue to enhance the ionic conductivity and stability of SEs.

Protective NaSICON Interlayer between a Sodium-Tin Alloy Anode and Sulfide-Based Solid Electrolytes for All-Solid-State Sodium Batteries.

This paper presents a suitable combination of different sodium solid electrolytes to surpass the challenge of highly reactive cell components in sodium batteries. The focus is laid on the introduction of ceramic Na3.4Zr2Si2.4P0.6O12 serving as a protective layer for sulfide-based separator electrolytes to avoid the high reactivity with the sodium metal anode. The chemical instability of the anode|sulfide solid electrolyte interface is demonstrated by impedance spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. The Na3.4Zr2Si2.4P0.6O12 disk shows chemical stability with the sodium metal anode as well as the sulfide solid electrolyte. Impedance analysis suggests an electrochemically stable interface. Electron microscopy points to a reaction at the Na3.4Zr2Si2.4P0.6O12 surface toward the sulfide solid electrolyte, which does not seem to affect the performance negatively. The results presented prove the chemical stabilization of the anode-separator interface using a Na3.4Zr2Si2.4P0.6O12 interlayer, which is an important step toward a sodium all-solid-state battery. Due to the applied pressure that is mandatory for battery cells with sulfide-based cathode composite, the use of a brittle ceramic in such cells remains challenging.

Nanoporous silicon fiber networks in a composite anode for all-solid-state batteries with superior cycling performance

All-solid-state batteries comprising Si anodes are promising materials for energy storage in electronic vehicles because their energy density is approximately 1.7 times higher than that of graphite anodes. However, Si undergoes severe volume changes during cycling, resulting in the loss of electronic and ionic conduction pathways and rapid capacity fading. To address this challenge, we developed composite anodes with a nanoporous Si fiber network structure in sulfide-based solid electrolytes (SEs) and conductive additives. Nanoporous Si fibers were fabricated by electrospinning, followed by magnesiothermic reduction. The total pore volume of the fibers allowed pore shrinkage to compensate for the volumetric expansion of Li12Si7, thereby suppressing outward expansion and preserving the Si-SE (or conductive additive) interface. The network structure of the lithiated Si fibers compensates for electronic and ionic conduction pathways even to the partially delaminated areas, leading to increased Si utilization. The anodes exhibited superior performance, achieving an initial Coulombic efficiency of 71%, a reversible capacity of 1474 mAh g−1, and capacity retention of 85% after 40 cycles with an industrially acceptable areal capacity of 1.3 mAh cm−2. The proposed approach can reduce the constraint pressure during charging/discharging and may have practical applications in large-area all-solid-state batteries.

New Insights of Infiltration Process of Argyrodite Li6PS5Cl Solid Electrolyte into Conventional Lithium-Ion Electrodes for Solid-State Batteries

All-solid-state lithium-ion batteries based on solid electrolytes are attractive for electric applications due to their potential high energy density and safety. The sulfide solid electrolyte (e.g., argyrodite) shows a high ionic conductivity (10−3 S cm−1). There is an open question related to the sulfide electrode’s fabrication by simply infiltrating methods applied for conventional lithium-ion battery electrodes via homogeneous solid electrolyte solutions, the structure of electrolytes after drying, chemical stability of binders and electrolyte, the surface morphology of electrolyte, and the deepening of the infiltrated electrolyte into the active materials to provide better contact between the active material and electrolyte and favorable lithium ionic conduction. However, due to the high reactivity of sulfide-based solid electrolytes, unwanted side reactions between sulfide electrolytes and polar solvents may occur. In this work, we explore the chemical and electrochemical properties of the argyrodite-based film produced by infiltration mode by combining electrochemical and structural characterizations.