Sub-2 Microm Research Articles

Comparison of columns packed with porous sub‐2 μm particles and superficially porous sub‐3 μm particles for peptide analysis at ambient and high temperature

The objective of this study was to evaluate various chromatographic approaches for peptide analysis. Initially, the ultra-HPLC (UHPLC) strategy, which consists of using columns packed with sub-2 microm particles at a maximal pressure of 1000 bar, was tested. To limit the backpressure generated by small particles, columns packed with superficially porous sub-3 microm particles (fused-core technology) that should theoretically improve mass transfer, particularly beneficial for large biomolecules, were investigated. To evaluate these claims, kinetic plots were constructed in both isocratic and gradient modes at ambient and elevated temperature (up to 90 degrees C). For peptide analysis, both UHPLC and fused-core technologies showed a significant gain in peak capacity when compared with conventional HPLC using 5 mum particles and monolithic supports. Additionally, it has been shown that high temperature was of utmost interest to further improve kinetic performance and peak shape due to the improvement of secondary interaction kinetics. Finally, the best conditions developed for UHPLC using the gradient kinetic plot methodology were applied to the analysis of a complex tryptic digest of various proteins. The expected and experimental peak capacity values obtained were similar. In addition, the resolving power of UHPLC at 60 degrees C was appropriate for resolving complex mixtures of peptides.

Simultaneous determination of quinolones in fish by liquid chromatography coupled with fluorescence detection: Comparison of sub‐2 μm particles and conventional C18 columns

A simple and effective multi-residue analysis method is presented for the extraction and determination of eleven quinolones (pipemidic acid, enoxacin, norfloxacin, ciprofloxacin, lomefloxacin, enrofloxacin, gatifloxacin, difloxacin, oxolinic acid, nalidixic acid and flumequine) in fish tissues. In this study, multi-residue separations on four columns packed with 5 microm or sub-2 microm particles were simultaneously developed for the purpose of comparison. Various gradients were optimized and best resolutions were achieved on each column. A short and sub-2 microm particle-sized HPLC column was chosen for its advantages in analysis time and column performance. Additionally, considering the matrix effect of the complex crude fish tissue, an effective extraction protocol was also established for sample pre-treatment procedure. Good recoveries (71-98%) were obtained from samples fortified with a mix of eleven quinolones at three levels, with satisfactory relative standard deviations and limits of detection. As a result, the sub-2 microm HPLC column and proposed analytical procedures have been evaluated and applied to the analysis of different fish tissues. Detectable residues were observed in 8 of 30 samples, at concentrations ranging from 4.74 to 23.27 microg/kg.

Separation of 2-aminobenzamide labeled glycans using hydrophilic interaction chromatography columns packed with 1.7μm sorbent

Separation by hydrophilic interaction chromatography (HILIC) with fluorescence detection utilizing a sub-2 microm glycan column for the separation of 2-aminobenzamide (2-AB) labeled N-linked glycans is described. The HILIC column packed with a 1.7 microm amide sorbent improves the peak capacity compared to a 3.0 microm HILIC column by a similar degree as observed in reversed-phase ultra-performance liquid chromatography (RP-UPLC). The results indicated that the optimal peak capacity was achieved at flow rate 0.2-0.5 mL/min. HILIC method transfer guidelines were shown to further enhance the resolution of glycans by changing initial gradient conditions, flow rate, column temperature, and different column lengths. Additionally, excellent resolution can be achieved in the separation of 2-AB labeled glycans released from fetuin, RNase B, and human IgG with a rapid analysis time.

A rapid ultra‐performance liquid chromatography/tandem mass spectrometric methodology for the in vitro analysis of Pooled and Cocktail cytochrome P450 assays

Drug-drug interaction evaluations of new pharmaceutical candidates are critical to preventing drug withdrawal and are routinely determined through the use of cytochrome P450 assays. The measurement of the effect of test compounds on the metabolism of known substrates allows for the determination of specific CYP450 isoenzyme inhibition and calculation of IC50 values. A sensitive, high-throughput ultra-performance liquid chromatography/tandem mass spectrometric (UPLC/MS/MS) method is presented for the evaluation of CYP450 inhibition. The assay was performed using a cocktail of probe substrates and the results were compared to those obtained with the more time-consuming methodology utilizing individual substrates. The use of a high-resolution, sub-2 microm particle, LC system allowed for a high-throughput assay of just 1 min. The extra resolution of the UPLC/MS/MS system allowed for the complete resolution of the analytes, with a fast switching MS for comprehensive data collection. The CYP450 inhibition results obtained using the substrate cocktail approach were found to be essentially identical to those obtained using individual substrates.

Fused‐core, sub‐2 μm packings, and monolithic HPLC columns: a comparative evaluation

Three different HPLC column technologies (i.e., monolith, fused-core particles, and sub-2 microm particles) were evaluated, comparing van Deemter plots, speed of analysis, back pressure, and mobile phase consumption. Very high linear velocities (approximately 12 mm/s) were achieved with the monolithic column using modest pressure (110 bar) at the expense of high mobile phase consumption. The minimum plate height of the monolith was similar to that of a 3 microm-particle packed column (i.e., h = 8 microm), operated at optimal linear velocities; the monolithic column showed substantially lower mass transfer dependence, however. The 2.7 microm fused-core packing material yielded efficiencies closer to the sub-2 microm material than to the 3 microm-particle packed column and could be operated at high flow rates. The fused-core column was able to achieve linear velocities similar to those attained on the sub-2 microm column, staying below 620 bar instead of almost near 1030 bar required by the sub-2 microm material. The lack of pH stability of the monolithic column prevented its use to separate basic compounds (i.e., tricyclic antidepressants) at high pH. Best separation of these components at high pH was achieved using the column packed with 1.7 microm hybrid material.

Fast chiral separation of drugs using columns packed with sub‐2 μm particles and ultra‐high pressure

The use of columns packed with sub-2 microm particles in liquid chromatography with very high pressure conditions (known as UHPLC) was investigated for the fast enantioseparation of drugs. Two different procedures were evaluated and compared using amphetamine derivatives and beta-blockers as model compounds. In one case, cyclodextrins (CD) were directly added to the mobile phase and chiral separations were carried out in less than 5 min. However, this strategy suffered from several drawbacks linked to column lifetime and low chromatographic efficiencies. In the other case, the analysis of enantiomers was carried out after a derivatization procedure using two different reagents, 2,3,4-tri-O-acetyl-alpha-D-arabinopyranosyl isothiocyanate (AITC) and N-alpha-(2,4-dinitro-5-fluorophenyl)-L-alaninamide (Marfey's reagent). Separation of several amphetamine derivatives contained within the same sample was achieved in 2-5 min with high efficiency and selectivity. The proposed approach was also successfully applied to the enantiomeric purity determination of (+)-(S)-amphetamine and (+)-(S)-methamphetamine. Similar results were obtained with beta-blockers, and the separation of 10 enantiomers was carried out in less than 3 min, whereas the individual separation of several beta-blocker enantiomers was performed in 1 min or less.

Fast log P determination by ultra-high-pressure liquid chromatography coupled with UV and mass spectrometry detections

Ultra-high-pressure liquid chromatography (UHPLC) systems able to work with columns packed with sub-2 microm particles offer very fast methods to determine the lipophilicity of new chemical entities. The careful development of the most suitable experimental conditions presented here will help medicinal chemists for high-throughput screening (HTS) log P(oct) measurements. The approach was optimized using a well-balanced set of 38 model compounds and a series of 28 basic compounds such as beta-blockers, local anesthetics, piperazines, clonidine, and derivatives. Different organic modifiers and hybrid stationary phases packed with 1.7-microm particles were evaluated in isocratic as well as gradient modes, and the advantages and limitations of tested conditions pointed out. The UHPLC approach offered a significant enhancement over the classical HPLC methods, by a factor 50 in the lipophilicity determination throughput. The hyphenation of UHPLC with MS detection allowed a further increase in the throughput. Data and results reported herein prove that the UHPLC-MS method can represent a progress in the HTS-measurement of lipophilicity due to its speed (at least a factor of 500 with respect to HPLC approaches) and to an extended field of application.

Separation of natural product using columns packed with Fused‐Core particles

Three HPLC columns packed with 3 microm, sub-2 microm, and 2.7 microm Fused-Core (superficially porous) particles were compared in separation performance using two natural product mixtures containing 15 structurally related components. The Ascentis Express C18 column packed with Fused-Core particles showed an 18% increase in column efficiency (theoretical plates), a 76% increase in plate number per meter, a 65% enhancement in separation speed and a 19% increase in back pressure compared to the Atlantis T3 C18 column packed with 3 microm particles. Column lot-to-lot variability for critical pairs in the natural product mixture was observed with both columns, with the Atlantis T3 column exhibiting a higher degree of variability. The Ascentis Express column was also compared with the Acquity BEH column packed with sub-2 microm particles. Although the peak efficiencies obtained by the Ascentis Express column were only about 74% of those obtained by the Acquity BEH column, the 50% lower back pressure and comparable separation speed allowed high-efficiency and high-speed separation to be performed using conventional HPLC instrumentation.

Ultra‐performance hydrophilic interaction liquid chromatography/tandem mass spectrometry for the determination of everolimus in mouse plasma

Ultra-performance hydrophilic interaction liquid chromatography (UPHILIC) interfaced with the electrospray ionization (ESI) source of a tandem mass spectrometer (MS/MS) was developed for the simultaneous determination of everolimus in mouse plasma samples. UPHILIC was performed on a sub-2 microm bare silica particle packing with the column pressure under traditional high-performance liquid chromatography (HPLC) to allow fast separation of pharmaceutical compounds within a chromatographic analysis time of 1 min. This UPHILIC technology is comparable with reversed-phase ultra-performance liquid chromatography (RPUPLC) in terms of chromatographic efficiency but demands neither expensive ultra-high-pressure instrumentation nor new laboratory protocols. With the ESI source, multiple reaction monitoring (MRM) of the ammoniated adduct ions of the analyte was used for tandem mass spectrometric detection. The retention mechanism profiles of the test compounds under HILIC conditions were explored. The influences of experimental factors such as the compositions of mobile phases on the chromatographic performance and the ionization efficiency of the test compounds in positive ion mode were investigated. A UPHILIC/MS/MS approach following a protein precipitation procedure was applied for the quantitative determination of everolimus at the low ng/mL region in support of a pharmacodynamic study. The analytical results obtained by the UPHILIC/MS/MS approach were fond to be in good agreement with those obtained by the RPUPLC/MS/MS method in terms of assay sample throughput, sensitivity and accuracy.

Fast liquid chromatography/multiple‐stage mass spectrometry of coccidiostats

Drugs that are used as medicines and also as growth promoters in veterinary care are considered as emerging environmental contaminants and in recent years concern about their potential risk to ecosystems and human health has risen. In this paper we used a method based on liquid chromatography/electrospray tandem mass spectrometry to analyze eight coccidiostatic compounds: diclazuril, dinitrocarbanilide (the main metabolite of nicarbazin), robenidine, lasalocid, monensin, salinomycin, maduramicin and nasarin. Multiple-stage mass spectrometry (MSn) based on the precursor ions [M+Na]+ (polyether ionophores), [M+H]+ (robenidine) and [M-H]- (diclazuril and dinitrocarbanilide) was used to study the fragmentation of these compounds. MSn data and genealogical relationships were used to propose a tentative assignment of the different fragment ions. Loss of water, decarboxylations, ketone beta-cleavages and rearrangement of cyclic ethers and amide groups were some of the fragmentations observed for these compounds. Liquid chromatography with a sub-2 microm particle size column was coupled to tandem mass spectrometry (LC/MS/MS) allowing the separation of these compounds in less than 7 min. Method detection limits ranging from 11 to 71 ng L(-1) and run-to-run values in terms of relative standard deviation (RSD) (up to 12%) were obtained.

Sub‐2 μm HPLC coupled with sub‐ppm mass accuracy for analysis of pharmaceutical compound libraries

Recent advances in accurate mass analysis are poised to allow the high-throughput production of accurate mass data on many more compounds than was previously available. It is shown that sub-ppm mass accuracy (producing elemental compositions) can be obtained on a simple TOF mass spectrometer operating in the manufacturer's standard mode. Concomitantly, there have been important technological advances in LC with respect to speed of analysis using sub-2 microm particle columns. Much of the sub-2 microm work in the literature has been under the label ultra performance LC (UPLC), however, we show that very high-speed results can be obtained using other manufacturer's pumps by using elevated column temperatures. Using elevated temperatures, HPLC peak widths on the order of 1 s can be obtained. We report the coupling of these two technologies (sub-ppm mass accuracy MS with high-speed HPLC) for the rapid analysis of compounds entering pharmaceutical libraries.

Evaluation of the coupling between ultra performance liquid chromatography and evaporative light scattering detector for selected phytochemical applications

Fast analysis in LC can be performed with sub-2 microm particles at very high pressures (up to 1000 bar) known as ultra performance LC (UPLC). With this configuration, it is possible to obtain fast and/or highly efficient separations compared to conventional LC. For the analysis of compounds without chromophores, the evaporative light scattering detector (ELSD) is an attractive alternative because of its quasi-universality, versatility, low-cost and good sensitivity. The UPLC-ELSD was investigated in terms of sensitivity and apparent efficiency, with a conventional ELSD instrument, for two types of commercially available nebulisers, using different mobile phase flow rates and column ids. Results were finally compared with the UPLC-UV configuration. Three applications with phytochemical compounds were selected to highlight the potential of this approach (i.e. the isocratic separations of artemisinin and its derivatives, of calystegines and the gradient separation of several tropane alkaloids). Depending on the used column length, baseline separations were obtained in 3-10 min, with an average apparent efficiency ranging from 7000 to 30,000 plates.

Addressing the analytical throughput challenges in ADME screening using rapid ultra‐performance liquid chromatography/tandem mass spectrometry methodologies

High-throughput ADME screening for compound drug development properties has become an essential part of the modern drug discovery process, allowing more informed decisions to be made on the best compounds to take forward in the discovery/development process. This however is a time-consuming process requiring multiple tests to be performed, demanding a significant amount of liquid chromatography/mass spectrometry (LC/MS) instrument time. This article focuses on the use of sub-2 microm porous particle LC coupled to tandem quadrupole MS/MS mass spectrometry for the rapid screening of ADME properties. Using this approach analysis times from 30 s to 1 min were achievable allowing analysis times to be cut by 80%. The use of the small particles coupled to high flow rates allowed for sufficient resolution, even with very short analysis time, to resolve the analytes of interest from similar compounds that would interfere with the assay. The use of dedicated, intelligent, software packages allowed for the user-free generation of MS/MS conditions and the processing of the data.

High‐temperature ultra‐performance liquid chromatography coupled to hybrid quadrupole time‐of‐flight mass spectrometry applied to ibuprofen metabolites in human urine

The application of sub-2 microm porous particle liquid chromatography (LC) operated at elevated temperatures, coupled with time-of-flight mass spectrometry (MS), to the separation and identification of metabolites of ibuprofen present in human urine following oral administrations is illustrated. The LC/MS system generated a high-resolution analytical separation that, with an analysis time of 20 min, provided a peak capacity in the order of ca. 350. Using this system a total of nine glucuronides of the drug and its metabolites were detected, including a number of isomeric acyl glucuronides of ibuprofen itself, a side-chain-oxidized carboxylic acid acyl glucuronide and a number of acyl glucuronides of various hydroxylated metabolites. The identities of the metabolites were confirmed by their accurate mass values and the presence of the common fragment ions from ibuprofen.

Characterisation of RPLC columns packed with porous sub‐2 μm particles

Eight commercially available sub-2 microm octadecyl silane columns (C18 columns) have been characterised by the Tanaka protocol. The columns can be grouped into two groups that display large differences in selectivity and peak shape due to differences in hydrophobicity, degree of surface coverage and silanol activity. Measurements of particle size distributions were made using automated microscopy and electrical sensing zone measurements. Only a weak correlation could be found between efficiency and particle size. Large differences in column backpressure were observed. These differences are not related to particle size distribution. A more likely explanation is differences in packing density. In order to take full advantage of 100-150 mm columns packed with sub-2 microm particles, it is often necessary to employ not only an elevated pressure but also an elevated temperature. A comparison between columns packed with sub-2, 3 and 5 microm versions of the same packing indicates potential method transferability problems for several of the columns due to selectivity differences. Currently, the best alternative for fast high-resolution LC is the use of sub-2 microm particles in combination with elevated pressure and temperature. However, as shown in this study additional efforts are needed to improve transferability as well as column performance.

Fused-Core Silica Column High-Performance Liquid Chromatography/Tandem Mass Spectrometric Determination of Rimonabant in Mouse Plasma

A high-performance liquid chromatography (HPLC) method using a fused-core silica particle packing was evaluated to allow fast and efficient separation for the analysis of pharmaceutical compounds. Fused-core particles are produced by "fusing" a porous silica layer onto a solid silica particle. The efficiencies of columns packed with 2.7 microm "fused-core" particles (a 0.5 microm porous shell fused to a solid 1.7 microm silica core particle) and 1.7 microm porous particles were compared in reversed-phase HPLC using rimonabant as an analyte. The fused-core silica materials providing the shorter diffusional mass transfer path for solutes are less affected in resolving power by increases in mobile-phase velocity than the sub-2 microm porous silica packings resulting in faster separations and higher sample throughput. This fast HPLC technology is comparable with ultrahigh-pressure liquid chromatography (UHPLC) in terms of chromatographic performance but demands neither expensive ultra-high-pressure instrumentation nor new laboratory protocols. The column effluent was directly connected to the atmospheric pressure chemical ionization (APCI) source prior to tandem mass spectrometric detection. In this work, the described fast HPLC-MS/MS and UHPLC-MS/MS approaches requiring approximately 1.5 min per sample were applied and compared for the determination of the rimonabant in mouse plasma samples at the low nanograms per milliliter region in support of a pharmacodynamic study.

The application of small porous particles, high temperatures, and high pressures to generate very high resolution LC and LC/MS separations

The effect of combining sub-2 microm porous particles with elevated operating temperatures on chromatographic performance has been investigated in terms of chromatographic efficiency, productivity, peak elution order, and observed operating pressure. The use of elevated temperature in LC does not increase the obtainable performance but allows the same performance to be obtained in less time. Increasing the column temperature did allow the use of longer columns, generating column efficiencies in excess of 100,000 plates and gradient peak capacities approaching 1000. Raising the temperature increased the optimal mobile phase linear velocity, negating somewhat the pressure benefits observed by reducing the solvent viscosity. When operating at higher temperature the analyte retention is not only reduced, but the order of elution will also often change. High temperature separations allowed exotic organic modifiers such as isopropanol to be exploited for alternative selectivity and faster analysis. Finally, care must be taken when using high temperature separations to ensure that the narrow peak widths produced do not compromise the quality of data obtained from detectors such as high resolution mass spectrometers.

Evaluation and comparison of very high pressure liquid chromatography systems for the separation and validation of pharmaceutical compounds

Chromatography using sub-2 microm particles is becoming increasingly popular due to the potential for increased speed, resolution, sensitivity, and peak capacity. To meet the demand, various vendors have re-engineered traditional LC systems to operate at pressures of up to 15000 psi to accommodate the elevated backpressures associated with using sub-2 microm particles. This report investigates and compares the performance of three very high pressure LC (VHPLC) systems: Waters Acquity, Agilent 1200 SL, and Thermo Accela. Specifications for the pump, autosampler, column compartment, detector, and software for each instrument are presented. To assess the chromatographic performance of the three instruments, method development and validation were performed for three pharmaceutical compounds and the results are compared and discussed. The material presented herein serves to highlight the different features of the VHPLC instruments, and assess their suitability for the analysis of pharmaceutical compounds.

Strategies to avoid false negative findings in residue analysis using liquid chromatography coupled to time‐of‐flight mass spectrometry

Liquid chromatography coupled to orthogonal acceleration time-of-flight mass spectrometry (LC/TOF) provides an attractive alternative to liquid chromatography coupled to triple quadrupole mass spectrometry (LC/MS/MS) in the field of multiresidue analysis. The sensitivity and selectivity of LC/TOF approach those of LC/MS/MS. TOF provides accurate mass information and a significantly higher mass resolution than quadrupole analyzers. The available mass resolution of commercial TOF instruments ranging from 10 000 to 18 000 full width at half maximum (FWHM) is not, however, sufficient to completely exclude the problem of isobaric interferences (co-elution of analyte ions with matrix compounds of very similar mass). Due to the required data storage capacity, TOF raw data is commonly centroided before being electronically stored. However, centroiding can lead to a loss of data quality. The co-elution of a low intensity analyte peak with an isobaric, high intensity matrix compound can cause problems. Some centroiding algorithms might not be capable of deconvoluting such partially merged signals, leading to incorrect centroids.Co-elution of isobaric compounds has been deliberately simulated by injecting diluted binary mixtures of isobaric model substances at various relative intensities. Depending on the mass differences between the two isobaric compounds and the resolution provided by the TOF instrument, significant deviations in exact mass measurements and signal intensities were observed. The extraction of a reconstructed ion chromatogram based on very narrow mass windows can even result in the complete loss of the analyte signal. Guidelines have been proposed to avoid such problems. The use of sub-2 microm HPLC packing materials is recommended to improve chromatographic resolution and to reduce the risk of co-elution. The width of the extraction mass windows for reconstructed ion chromatograms should be defined according to the resolution of the TOF instrument. Alternative approaches include the spiking of the sample with appropriate analyte concentrations. Furthermore, enhanced software, capable of deconvoluting partially merged mass peaks, may become available.

Fast analysis in liquid chromatography using small particle size and high pressure

In order to enhance chromatographic performances in terms of efficiency and rapidity, LC has recently evolved in the development of short columns packed with small particles (sub-2 microm) working at high pressures (> 400 bar). This approach has been described 30 years ago according to the fundamental chromatographic equations. However, systems and columns compatible with such high pressures have been introduced in the market in 2004 only. Advantages of small particles working at high pressure will be discussed in terms of sensitivity, efficiency, resolution, and analysis time. Potential problems encountered with high pressure in terms of frictional heating and solvent compressibility will also be discussed even if systems working at a maximum pressure of 1000 bar are not influenced by these parameters and give reliable and reproducible results. Several applications will highlight the potential and interest of this new technology.