Strip Width Research Articles

Impacts of different vegetation in riparian buffer strips on runoff and sediment loss.

Buffer strips continue to feature in the management of agricultural runoff and water pollution in many countries. Existing research has explored their efficacy for reducing environmental problems in different geoclimatic settings but, the evidence on the efficacy of different vegetation treatments is less abundant than that for other buffer strip characteristics, including width, and is more contradictory in nature. With policy targets for various environmental outcomes including water or air quality and net zero pointing to the need for conversion of agricultural land, the need for robust experimental evidence on the relative benefits of different vegetation types in buffer strips is now renewed. Our experiment used a replicated plot scale facility to compare the efficacy of 12 m wide buffer strips for controlling runoff and suspended sediment loss during 15 sampled storms spanning 2017-2020. The buffer strips comprised three vegetation treatments: a deep rooting grass (Festulolium cv. Prior), a short rotation coppice willow and native broadleaved woodland trees. Over the duration of the monitoring period, reductions in total runoff, compared with the experimental control, were in the order: willow buffer strips (49%); deciduous woodland buffer strips (46%); grass buffer strips (33%). The corresponding reductions in suspended sediment loss, relative to the experimental control, were ordered: willow buffer strips (44%) > deciduous woodland buffer strips (30%) > grass buffer strips (29%). Given the 3-year duration of our new dataset, our results should be seen as providing evidence on the impacts during the establishment phase of the treatments.

Dynamics of stand productivity in Moso bamboo forest after strip cutting.

Strip cutting can effectively reduce the cutting cost of bamboo forests and promote the transformation and upgradation of bamboo forests through mechanization and modernization. Despite the rapid accumulation of Moso bamboo biomass, the dynamics of five years changes in stand characteristics and productivity after cutting remain unclear. This is critical for formulating efficient bamboo forest management measures. In this paper, plots with an 8m width strip cut (SC) and respective reserved belts (RB) were selected as the research object, and the traditional management forest (CK) as control. The dynamic characteristics of stand, biomass distribution pattern, and productivity change in the different treatment plots were studied for 5 years after cutting. The results showed that cutting increased the number of shoots and new bamboo, and decreased the diameter at breast height, height to crown base, and height of new bamboo (p<0.05). Cutting reduces the productivity of both SC and RB, and allocates more biomass to the bamboo leaves to capture light in SC (p<0.05). Over time, the characteristics of new bamboo in SC reached the level of CK, and the density of standing bamboo, and productivity, were higher than those in CK. However, the number and productivity of new bamboo decreased significantly in the RB (p<0.05), which reflected the density restriction effect of bamboo forest. Further analysis showed that the increase in productivity in SC and CK was mainly from Moso bamboo at II and III "du", which positively correlated with the soil contents of total nitrogen, total phosphorus, and available phosphorus. It was suggested that after three On-year restorations, the SC could reach the level of CK, however it is necessary to density manage RB from the second On-year after cutting.

Manufacturing and Characterization of Wide-Bundle Bamboo Scrimber: A Comparison with Other Engineered Bamboo Composites.

Controlling the variability in mat structure and properties in bamboo scrimber (BS) is key to producing the product for structural applications, and wide strip scrimber (WBS) is an effective approach. In this study, the effects of scrimmed bamboo bundle morphology and product density on the properties of WBS were investigated. WBS panels were manufactured and tested using wide (200 to 250 mm) bamboo strips with different fiberization intensity. Maximum strength properties (flexural, compressive, and shear strength), and lowest thickness swelling and water absorption were achieved with three or four passes due to the higher resin absorption by strips. For balanced product cost and performance, we recommend 1-2 fiberization passes and a panel density of 0.9-1.0 g/cm3. Panel mechanical properties were compared with other common bamboo composites. Bamboo scrimber products were highly variable in properties due to differing manufacturing processes, element treatments, and suboptimal mat structure. Products including laminated bamboo lumber and flattened bamboo made from nonfiberized elements show markedly different relationships between strength and elastic properties mostly due to inadequate bonding between the laminae, which causes premature bond-line failure. This study helped improve the understanding of the structure-property relationship of engineered bamboo products while providing insights into process optimization.

Development of a Segmented GEM Readout detector

Micromegas (Micro-MEsh GAseous Structures) detectors are a type of micro-pattern gaseous detectors. The primary charges are amplified in electron avalanches between a planar anode and a mesh typically 120 μm above the anode. For resistive anode type Micromegas detectors the signal is read out via copper readout strip layers below the anode. A 2D particle position can be reconstructed using two perpendicular readout strip layers below the resistive anode structure.Using a standard 2D resistive anode Micromegas readout structure, a unique 2D particle position reconstruction is only possible if the detector is hit by only one particle at the same time. Ambiguities will occur if multiple particles arrive at the same time. A unique X–Y assignment is strongly complicated.This issue can be resolved by replacing the mesh with a GEM (Gas Electron Multiplier) foil, which is segmented into 0.5 mm wide strips on at least one of the two sides. The GEM strips need to be turned by 45∘ with respect to the Micromegas readout strips. Thus the detector with a GEM foil segmented on both sides has four readout strip directions (X, Y, U and V) and a detector with a GEM foil segmented on only one side has three readout strip directions (X, Y and V).A prototype of such a Segmented GEM Readout (SGR) detector is built with GEM strips and readout strips perpendicular to each other. Test beam measurements with this detector were performed using 120 GeV muons. Results of the test beam measurements are presented here.

Investigation of CFRP Reinforcement Ratio on the Flexural Capacity and Failure Mode of Plain Concrete Prisms.

The utilization of carbon-fiber-reinforced polymer (CFRP) composites as strengthening materials for structural components has become quite famous over the last couple of decades. The present experimental study was carried out to examine the effect of varied widths of externally bonded CFRP on the debonding strain of CFRP and the failure mode of plain concrete beams. Twelve plain concrete prims measuring 100 mm × 100 mm × 500 mm were cast and tested under identical loading conditions. The twelve specimens include two control prisms, i.e., without CFRP strips, and the remaining ten prisms were reinforced with CFRP strips with widths of 10 mm, 20 mm, 30 mm, 40 mm, and 50 mm, respectively, i.e., two prisms in each group. Four-point loading flexural testing was carried out, and the resulting data are presented in the form of peak load vs. midpoint displacement, load vs. concrete strain, and load vs. CFRP strain. The peak load was directly recorded from the testing machine, while the midpoint deflection was recorded through the linear variable differential transducer (LVDT) installed at the midpoint. To measure the strain, two separate strain gauges were installed at the bottom of each concrete prism, i.e., one on the concrete surface and the other on the surface of the CFRP strip. The results of this study indicate that the debonding strain is a function of CFRP strip width and that the failure patterns of beams are significantly affected by the CFRP reinforcement ratio.

Experimental study and theoretical analysis on the flexural behavior of glulam bolted joints with prestressed steel strips

The glulam bolted joint with prestressed steel strips was proposed and investigated systematically. Experimental study was conducted considering the variation of pre-strain of steel strips. The presence of prestressed steel strips led to a delay in the onset and propagation of cracking with a pronounced increase in bearing capacity compared with ordinary glulam bolted joints, i.e. by 41.15%, 52.01% and 53.33%, respectively, and significantly higher deformation capacity, with the ductility increasing by 15.38%, 88.11% and 104.90% respectively. A three-dimensional finite element analysis considering mixed-mode cohesive zone modeling was performed and verified to be effective to reproduce crack path observed in the experiments. Moreover, a quasi-non-linear fracture mechanics model based on a Timoshenko beam on elastic foundation theory was extended in order to take into account the influence of the prestressed steel strips on the ultimate bearing capacity. Analytical results demonstrated how ultimate bearing capacity changed with pre-strain, thickness, width and spacing of strips and a series of design recommendations were supplied.

Effects of Row Spacing and Planting Pattern on Photosynthesis, Chlorophyll Fluorescence, and Related Enzyme Activities of Maize Ear Leaf in Maize–Soybean Intercropping

With the continuous improvement of the mechanization level and the development of new crop varieties, the optimal strip width for intercropping crops is important. In this study, field experiments were conducted to analyze the effects of different row spacings and planting patterns on photosynthesis, chlorophyll fluorescence, and the related enzyme activities of maize ear leaves in a maize–soybean intercropping system using two planting patterns (wide–narrow rows of 80–50 cm and uniform ridges of 65 cm) and two intercropping ratios (four rows of maize and four rows of soybean; six rows of maize and six rows of soybean). The results showed that the pattern of wide–narrow-row spacing significantly improved the photosynthetic capacity of maize compared with the uniform-ridge planting pattern, along with marked elevation in the values of stomatal conductance (Gs), the transpiration rate (Tr), and the photosynthetic rate (Pn). On the other hand, the values of photochemical quenching (qP), actual photochemical efficiency (φPSII), and maximum photochemical efficiency (Fv/Fm) also significantly increased, and the effect of D-M6S6 treatment was the most significant on these parameters. Similarly, the activities of phosphoenolpyruvate carboxylase and ribulose-1,5-bisphosphate carboxylase/oxygenase also increased significantly. Among different treatments, the yield under the D-M6S6 treatment was the highest. Therefore, based on the planting pattern of the wide–narrow-row spacing, the intercropping of six rows of maize and six rows of soybean is the better design in the semi-arid regions of western China.

Online magnetic flux leakage detection of inclusions and inhomogeneities in cold rolled steel plate

Abstract Cold rolled steel plate is found in different applications. In manufacturing processes with high stretch ratios like bending or deep drawing, non-metallic inclusions, or segregations, which remain in the material during slab casting, can lead to ruptures of the plate. While not being visible optically, those inclusions are detectable by magnetic flux leakage inspection. Therefore, an online inspection system using giant magnetoresistance gradiometers was developed. The individual components were optimized by researching the magnetic properties of the cold rolled plate and natural as well as artificial defects on a laboratory setup for moving material simulation. Correlations between defect properties, inspection parameters and the resulting signals were determined. By optimizing components and configuration accordingly, a sensor module containing 48 sensors, signal conditioning, digitization, and an adjustable magnet was arrived at. Due to the necessarily small distance to the moving material, attention was paid to mechanical repeatability and ruggedness. An inclusion detection system, fully covering 1344 mm strip width, was installed in a coating line. Operating in production for over a year, the inspection system has shown high sensitivity and is, in addition to internal defects, able to detect various strip damages like roll marks and scratches.

Aeolization on the Atlantic coast of Galicia (NW Spain) from the end of the last glacial period to the present day: Chronology, origin and evolution of coastal dunes linked to sea‐level oscillations

AbstractThe Atlantic coast of Galicia (NW Spain) is a high‐energy environment where shingle beaches are currently developing. These coarser sediments alternate with sandy deposits which are also considered as beaches typical of a low‐energy environment. The physical association of both types of sediment with contrasted sedimentary significance raises problems of interpretation. The study of four outcrops of fossil aeolianites on this coast has allowed us to reconstruct their evolution from the end of the Upper Pleistocene to the present day. Their chronology, estimated by optically stimulated luminescence between 35 and 14 ky at the end of the last glaciation (MIS2), coincides with a local sea level 120 m below the present one. This implies a coastline shifted several kilometres from its current location and the subaerial exposure of a wide strip of the continental shelf covered by sands. The wind blew sand to form dunes towards the continent, covering the coastal areas, which then emerged with no other limitation than the active river channels. Sea‐level rise during the Holocene transgression has progressively swamped these aeolian deposits, leaving only flooded dunes, relict coastal dunes and climbing dunes on cliffs up to 180 m high. The aeolian process continued as long as there was a sandy source area to erode, although accretion finished when the sea reached its current level (Late Holocene). Since then, the wind turned from accretion to erosion of the dunes and sand beaches. This erosion exposes the older shingle beaches (probably of Eemian age) buried under the aeolian sands, as well as old, submerged forest remains and megalithic monuments. The destruction of sand beaches and dunes currently observed along the Galician coast is linked, according to most researchers, to anthropogenic global warming. However, their management should consider these evolutive issues.

Metal-insulator-metal strip spectroscopic infrared photothermal absorber based on uniaxially oriented plasmonic lanthanum hexaboride films.

We report the fabrication of a mid-infrared device using LaB6 - Al2O3 - LaB6 trilayers, with an array of LaB6 strips as the top layer. Uniaxially oriented lanthanum hexaboride (LaB6) films self-organized in a (100) orientation were adopted together with a lithographic process using laser direct writing followed by reactive ion etching. The fabricated infrared absorbers based on our electromagnetic design exhibited excellent resonant absorption and flexible tunability by changing the periodicity and width of the top LaB6 strips. We examined the performance of epitaxial and sputtered LaB6 films by fabricating two different types of absorbers using sputtered LaB6(100) and epitaxial LaB6(100) films for the bottom mirror layers. Owing to a difference in crystallinity, the latter exhibited a lower background in the absorption spectra as well as in the thermal emission spectra, indicating its good spectral selectivity.

Three-Dimensional Mesoscopic Investigation on the Impact of Specimen Geometry and Bearing Strip Size on the Splitting-Tensile Properties of Coral Aggregate Concrete

The use of coral aggregate concrete (CAC) as a novel construction material has attracted significant attention for the construction of reef engineering structures. To investigate the static splitting-tensile behaviors of CAC under the influence of two factors, namely specimen geometry and bearing strip size, a three-dimensional (3D) mesoscale modeling approach with consideration for aggregate randomness in shape and distribution was adopted in this study. We established 12 different specimen models with two specimen shapes (i.e., a cube with an edge length of 150 mm and a cylinder with dimensions of ϕ 150 mm × 300 mm) and six strip widths (i.e., 6, 9, 12, 15, 18, and 20 mm) for calculation. The effects of specimen geometry and strip width on the splitting-tensile properties of CAC, such as failure processes, final failure patterns, and splitting-tensile strength ( f st ), are analyzed and discussed systematically. The results indicate the high reliability of the developed mesoscale modeling approach and reveal the optimal computational parameters for simulating and predicting the splitting-tensile properties of CAC. The f s t values of CAC are associated with both the specimen geometry and width of the bearing strip. The f st values of the cube model are slightly higher than those of the cylinder model for the same bearing strip size, representing geometry effects that can be explained by differences in fracture area. Additionally, the f st value of CAC gradually increases with the relative width of the bearing strip ranging from 0.04 to 0.13. Based on the elastic solution theory, the variation area of CAC f st values with the relative width of the bearing strip was determined preliminarily, which has great significance for studying the tensile performance of CAC.

Repeated application of riboflavin during corneal cross-linking does not improve the biomechanical stiffening effect ex vivo

PurposeTo evaluate whether repeated application of riboflavin during corneal cross-linking (CXL) has an impact on the corneal biomechanical strength in ex-vivo porcine corneas. DesignLaboratory investigation. MethodsSixty-six porcine corneas with intact epithelium were divided into three groups and analyzed. All corneas were pre-soaked with an iso-osmolar solution of 0.1% riboflavin in a phosphate-buffered saline (PBS) solution (“riboflavin solution”). Then, the corneas in Groups 1 and 2 were irradiated with a standard epi-off CXL (S-CXL) UV-A irradiation protocol (3 mW/cm2 for 30 min); while the corneas in Group 3 were not irradiated and served as control. During irradiation, Group 1 (CXL-PBS-Ribo) received repeated riboflavin solution application while corneas in Group 2 (CXL-PBS) received only repeated iso-osmolar PBS solution. Immediately after the procedure, 5-mm wide corneal strips were prepared, and elastic modulus was calculated to characterize biomechanical properties. ResultsSignificant differences in stress-strain extensiometry were found between two cross-linked groups with control group (P = 0.005 and 0.002, respectively). No significant difference was observed in the normalized stiffening effect between Groups 1 and 2 (P = 0.715). ConclusionsThe repeated application of riboflavin solution during UV-A irradiation does not affect the corneal biomechanical properties achieved with standard epi-off CXL. Riboflavin application during CXL may be omitted without altering the biomechanical stiffening induced by the procedure.

An MT-InSAR Data Partition Strategy for Sentinel-1A/B TOPS Data

The Sentinel-1A/B satellite launched by European Space Agency (ESA) in 2014 provides a huge amount of free Terrain Observation by Progressive Scans (TOPS) data with global coverage to the public. The TOPS data have a frame width of 250 km and have been widely used in surface deformation monitoring. However, traditional Multi-Temporal Interferometric Synthetic Aperture Radar (MT-InSAR) methods require large computer memory and time when processing full resolution data with large width and long strips. In addition, they hardly correct atmospheric delays and orbital errors accurately over a large area. In order to solve these problems, this study proposes a data partition strategy based on MT-InSAR methods. We first process the partitioned images over a large area by traditional MT-InSAR method, then stitch the deformation results into a complete deformation result by correcting the offsets of adjacent partitioned images. This strategy is validated in a flat urban area (Changzhou City in Jiangsu province, China), and a mountainous region (Qijiang in Chongqing City, China). Compared with traditional MT-InSAR methods, the precision of the results obtained by the new strategy is improved by about 5% for Changzhou city and about 15% for Qijiang because of its advantage in atmospheric delay correction. Furthermore, the proposed strategy needs much less memory and time than traditional methods. The total time needed by the traditional method is about 20 h, and by the proposed method, is about 8.7 h, when the number of parallel processing is 5 in the Changzhou city case. The time will be further reduced when the number of parallel processes increases.

Forceless folding of thin annular strips

Thin strips or sheets with in-plane curvature have a natural tendency to adopt highly symmetric shapes when forced into closed structures and to spontaneously fold into compact multi-covered configurations under feed-in of more length or change of intrinsic curvature. This disposition is exploited in nature as well as in the design of everyday items such as foldable containers. We formulate boundary-value problems (for an ODE) for symmetric equilibrium solutions of unstretchable circular annular strips and present sequences of numerical solutions that mimic different folding modes. Because of the high-order symmetry, closed solutions cannot have an internal force, i.e., the strips are forceless. We consider both wide and narrow (strictly zero-width) strips. Narrow strips cannot have inflections, but wide strips can be either inflectional or non-inflectional. Inflectional solutions are found to feature stress localisations, with divergent strain energy density, on the edge of the strip at inflections of the surface. ‘Regular’ folding gives these singularities on the inside of the annulus, while ‘inverted’ folding gives them predominantly on the outside of the annulus. No new inflections are created in the folding process as more length is inserted. We end with a discussion of an intriguing apparent connection with a deep result on the topology of curves on surfaces.

Low-velocity impact behavior of two-way RC slab strengthening with carbon TRM strips

Sudden dynamic impact loading on reinforced concrete (RC) slabs due to reasons such as the impact of debris due to landslide or rock fall, the impact of drifting objects due to effects such as flood or tsunami, the impact of vehicles on highway or seaway bridges, the impact of air shock waves due to explosions inside or outside of structures may lead damage and collapses. This study is aimed to examine the behavior of RC slabs reinforced with Textile Reinforced Mortar (TRM) strips, which have been used in reinforcement applications for the last ten years, under the effect of sudden dynamic impact loading. The variables examined in the experimental study are the TRM strip width, the placement of the strips, and whether the anchors are present on the strips or not. The acceleration-time, displacement–time, strain–time over the strips, and applied impact loading-time distributions are measured and interpreted under the effect of impact loading with a constant energy level applied by the drop-weight system. In addition, numerical analysis of the slabs is done with Ls-Dyna software, compared with the experimental results, and examines how successful the analysis results are. The reinforcement technique applied with TRM strips developed within this study's scope significantly increased RC slabs' performance under impact loading. The TRM strips used for strengthening in both directions were the variable that had the most positive effect on impact behavior. Increasing the strip width and anchoring followed the use of double directional strips in improving performance under the impact loading.

Development of fabrication technologies for the first wall of the HCCR blanket

The helium-cooled ceramic reflector (HCCR) concept is a primary candidate among demonstration fusion power reactor (DEMO) blanket options in Korea. The HCCR blanket is composed of a first wall (FW), a breeding zone, side cover plates and a back manifold. This study focuses on fabrication technologies for the FW using laser-beam welding (LBW) and hot isostatic pressure (HIP) bonding. Permanent backing strips in the pressure boundaries of the HCCR blanket are not allowed according to regulations related to pressure vessels and nuclear pressure vessels because high-pressure helium gas at 8 MPa is used as the coolant. LBW conditions and procedures for the fabrication of a FW without backing strips were investigated using small mock-ups with an advanced reduced-activation alloy called ARAA, which was developed in Korea. The laser beam power, thickness of the cover plate, and width of the backing strips were considered as parameters. The LBW conditions and procedures were optimized to remove the backing strip and achieve uniform and continuous back beads. After LBW, the fabrication of the FW with small mock-ups was completed by joining the back plate with HIP bonding. The small mock-ups were subject to very high temperatures exceeding 1000°C during the LBW and HIP bonding processes, which led to changes in the microstructures and hardness levels. The microstructures and hardness levels were recovered through post-heat treatments performed after HIP bonding. The microstructures of the HIP bonding interface after the heat treatments were observed. A partial HIP bonding line was confirmed and transverse tensile tests were carried out to investigate the impact of the partial HIP bonding line on the mechanical properties of the HIP bonding interface. The tensile strength of the HIP bonding interface was approx. 2% lower than that of the base metal, indicating that the partial HIP bonding line caused a slight decrease in the tensile strength, but the impact on the HCCR blanket design would be negligible.

Geographic scouts of Central Asia

In the second half of the XIX century . Russia pursued an active policy in the Central Asian khanates, firmly determined to move its border beyond a wide strip of deserts and semi-deserts. At the same time, the rivalry between the Russian and British Empires for influence and control over the Central Asian khanates unfolded. It was a political, diplomatic and geopolitical duel, the so-called “Big Game”, in which intelligence played one of the main roles. To fulfill the tasks facing the intelligence, Russia has attracted scientific historical-geographical and military-topographic expeditions under the auspices of the Imperial Russian Geographical Society (IRGO). It was they who at the end of the XIX century. In a certain part became one of the main activities of the IRGO.The best officers of the General Staff were attracted to participate in them. It was their heroic efforts that made it possible to fill in the gaps in the knowledge of Central Asia and, especially, its western part of Uyguria (East Turkestan) and Inner Mongolia.In recent decades, due to the geopolitical processes that are taking place in the Eurasian space, historical, geographical achievements that have become world-wide have again attracted attention. Again, we have to hear about a new “Big Game” that takes place for the same values — resources, territories, trade routes. The tasks and political and technological methods of conducting geopolitical rivalry have changed. However, gratitude should remain in memory for having contributed to the implementation of the foreign policy of the Russian Empire by conducting intelligence research of the expanses of Central Asia.

Bioinspired polypyrrole based fibrillary artificial muscle with actuation and intrinsic sensing capabilities

A non-conventional, bioinspired device based on polypyrrole coated electrospun fibrous microstructures, which simultaneously works as artificial muscle and mechanical sensor is reported. Fibrous morphology is preferred due to its high active surface which can improve the actuation/sensing properties, its preparation still being challenging. Thus, a simple fabrication algorithm based on electrospinning, sputtering deposition and electrochemical polymerization produced electroactive aligned ribbon meshes with analogous characteristics as natural muscle fibers. These can simultaneously generate a movement (by applying an electric current/potential) and sense the effort of holding weights (by measuring the potential/current while holding objects up to 21.1 mg). Electroactivity was consisting in a fast bending/curling motion, depending on the fiber strip width. The amplitude of the movement decreases by increasing the load, a behavior similar with natural muscles. Moreover, when different weights were hung on the device, it senses the load modification, demonstrating a sensitivity of about 7 mV/mg for oxidation and − 4 mV/mg for reduction. These results are important since simultaneous actuation and sensitivity are essential for complex activity. Such devices with multiple functionalities can open new possibilities of applications as e.g. smart prosthesis or lifelike robots.

Conversion of low-value stands by corridor method in Left-Bank Forest-Steppe, Ukraine

Abstract The aim of the study was to identify the influence of different widths and cardinal directions of felled corridors on the condition and mensuration characteristics of the English oak trees planted there during the conversion of low-value young stands using the corridor method. The study was carried out in oak forests in the forest-steppe zone at a permanent sample plot. The experiment included the conversion of a low-value 8-year-old stand to improve its species composition. The sample plots were laid out in a fertile hardwood forest site. The conversion was realised by felling corridors of various widths (6, 9 and 12 m) and directions and planting English oak trees (Quercus robur L.) within them in rows. For the planted oaks, tending felling was carried out three times: weeding (8 years), cleaning (13 years) and thinning (32 years). A comparative analysis of mensuration characteristics (average height, diameter, growing stock, radial increment, health condition, etc.) was carried out for 32-year-old oak trees grown in the corridors and a part of a low-value stand in the unfelled strips after the tending felling. It was found that the average height and diameter at breast height of oaks in the 6, 9 and 12 m wide corridors of different cardinal directions did not differ significantly. The difference in oak stocks within 6 and 9 m wide corridors of different cardinal directions was also insignificant. The stock differences were statistically significant for 6 and 12 m wide corridors as well as for 9 and 12 m wide ones. The article made recommendations on the width of felled corridors and unfelled strips to effectively convert low-value young stands by the corridor method.

Comparing different methods of position reconstruction considering 1D readout of GEM detectors

Gas Electron Multiplier (GEM) based detectors contain microstructures that provide amplification, via avalanche multiplication, for the charges generated due to ionizing radiation. The readout of the detector is responsible for collecting electrons multiplied by the GEM structure and it may be position sensitive. In this preliminary study, we created algorithms to compare the error of three different methods for position reconstruction. All these methods are based on weighted averages. In the algorithm we modeled an electron cloud as a normalized Gaussian function that is collected by a 1D readout of strips affected by white noise, then we made a clustering algorithm to identify the strips that collected the electron cloud. The method that uses the weight equal to squared charges shows the highest errors for narrow clouds, when the σ value (standard deviation of a Gaussian function) is closer to the strip width. Nonetheless, the errors of the three methods get similar results for a σ approximately equal to the width of one and a half strips.