Stripline Feed Research Articles

Inductive Frequency-Coded Sensor for Non-Destructive Structural Strain Monitoring of Composite Materials

Structural composite materials have gained significant appeal because of their ability to be customized for specific mechanical qualities for various applications, including avionics, wind turbines, transportation, and medical equipment. Therefore, there is a growing demand for effective and non-invasive structural health monitoring (SHM) devices to supervise the integrity of materials. This work introduces a novel sensor design, consisting of three spiral resonators optimized to operate at distinct frequencies and excited by a feeding strip line, capable of performing non-destructive structural strain monitoring via frequency coding. The initial discussion focuses on the analytical modeling of the sensor, which is based on a circuital approach. A numerical test case is developed to operate across the frequency range of 100 to 400 MHz, selected to achieve a balance between penetration depth and the sensitivity of the system. The encouraging findings from electromagnetic full-wave simulations have been confirmed by experimental measurements conducted on printed circuit board (PCB) prototypes embedded in a fiberglass-based composite sample. The sensor shows exceptional sensitivity and cost-effectiveness, and may be easily integrated into composite layers due to its minimal cabling requirements and extremely small profile. The particular frequency-coded configuration enables the suggested sensor to accurately detect and distinguish various structural deformations based on their severity and location.

An improved Mini Antenna Designed at 60GHZ for a New Generation Mobile Phone

Five-generation (5G) communication systems are being required to meet the needs of small, high-speed, and big bandwidth systems [2]. This paper simulates and designs a 60GHZ rectangular micro strip patch antenna. The proposed antenna resonates at 60GHZ with a return loss of -32.126 dB, efficiency of 87.7119%, and gain of 6.96485 dBi. The patch is 2.726 x 2.364 x 0.125 mm. The radiating patch and the 50Ω micro strip feed line are matched using an iset feed transmission line approach. A Roger RT Duroid 5880 substrate, with a height of 0.125mm and a dielectric constant of 2.20 and a loss tangent of 0.0009, was selected in the design. The Advanced Design System (ADS) was used to compute the antenna's parameters and evaluate the results of simulations.

MAGNETIC CORE APPLICATION IN A PLANAR RESONATOR WITH A YTTRIUM IRON GARNET FILM FOR ENHANCING STRONG PHOTON-MAGNON COUPLING

Subject and Purpose. This paper presents numerical simulation results on the transmission spectra of a split-ring resonator (SRR) loaded with a thin film of yttrium iron garnet (YIG). The application of a magnetic core in the SRR is proposed for increasing the photon-magnon (P-M) coupling strength. The anticrossing effect in the frequency dispersion behavior of the SRR modes and YIG film ferromagnetic resonance modes, namely SRR-YIG coupled modes, is identified. The dimensional parameters of the SRR with a magnetic core are calculated, taking care to preserve the design compactness and striving to obtain a maximum possible spin-number-normalized coupling strength for such a system. The work has been aimed at evaluating the efficiency of applying the magnetic core as a part of the planar microwave resonator to enhance the P-M coupling strength. Methods and Methodology. The transmission coefficient |S21| spectra of electromagnetic waves propagating through the planar resonator with the YIG film under the ferromagnetic resonance condition are numerically studied using the CST Studio Suite package in the frequency domain. The spatial distribution function of the magnetic field strength is calculated for the two scenarios of YIG film location: near the magnetic core (between the SRR and the feeding stripline) and inside the magnetic core (in the SRR center). Also, for each of these two scenarios, the transmission coefficient |S21| spectra of the wave propagation through the feeding stripline in the region of SRR-YIG coupled modes are simulated with and without the magnetic core. The dispersion curves of the SRR-YIG coupled modes are obtained in analytical terms. Results. It has been shown that the magnetic core application increases the P-M coupling strength 2.0 times in the scenario of YIG film location near the magnetic core (between the SRR and the feeding stripline). When the YIG film is inside the magnetic core (in the SRR center), the P-M coupling strength rises 2.3 times compared to similar cases without the magnetic core. Conclusions. The suggested magnetic core application can be used to increase the P-M coupling strength in the SRR — magnetic film resonant system, striving to develop effective microwave-to-optical converters and create efficient information exchange between quantum computers.

Design of Microstrip Patch Antenna for 5G Communications

Abstract: This project aims to design and implement a low-profile patch antenna for 5G communication application. The resonating frequency has been chosen as 3.5 GHz for 5G application. Rogers RT5880 (lossy) epoxy material with permittivity of 2.2 has been chosen for the substrate material which has fire redundant property. The size of the substrate is 60×60 mm. The proposed antenna is compact Star-Shape radiating patch with defected ground structure, and the feeding technique is used as strip line feed. This proposed Star-Shaped antenna has been designed, analyzed and simulated by CST microwave studio, an electromagnetic simulation software. Antenna parameters like S-Parameter, Antenna Gain, Directivity, Efficiency has been observed and tabulated the results. This proposed Star-Shape antenna is widely used for 5G mobile communication applications.

A novel wideband dielectric resonator antenna with compact size

ABSTRACT In this paper, a wideband dielectric resonator antenna with compact size is presented. The proposed antenna is formed by four dielectrics. Non-adjacent dielectrics have same permittivity constant. A 50-ohm micro strip feed line is used to exciting the antenna through the coupling slot. By optimizing the dimensions and structure of the antenna, impedance bandwidth of 3.25 to 4.4 GHz is obtained. Impedance bandwidth of the proposed antenna is a very wide bandwidth compared to the previous dielectric antennas. The antenna gain is about 9.6 dB.

Millimeter-wave Wideband High-isolation Antenna Array Based on End-fire Magnetoelectric Dipole Antenna for 5G Applications

In this paper, a millimeter-wave (mmW) wideband high-isolation wide-angle scanning antenna is presented. The end-fire magnetoelectric (ME) dipole with wideband impedance characteristic and wide beamwidth is selected. Based on the ME dipole, a 1×4 subarray with a stripline feed network is constructed to get higher antenna efficiency. Then, four 1×4 subarrays are adopted to form a 4×4 array to realize the wide-angle scanning performance. Furthermore, to get better isolation between the subarrays, the beam is tilted on the non-scanning plane; in addition, the resonant split rings are added on the background of the subarrays. With these two measures, the isolation between the subarrays can be effectively reduced, with more than 20 dB over the entire bandwidth. Owing to the wide beamwidth of ME dipole and high isolation between the subarrays, the 4×4 array can obtain the wide-angle scanning characteristic. The final antenna covers an operating bandwidth of 19.5% (24.25-29.5 GHz) with return loss more than 10 dB, which can meet the band in the 5G standard. The beam can scan approximately ±55∘ with a realized gain reduction under 3 dB within the wide operating bandwidth. Also, the simulated radiation efficiency of the array is more than 77% over almost the entire band. The antenna will be a potential candidate to be applied in 5G applications.

Low-Profile Wideband Dual-Polarized Dipole Antenna With Parasitic Strips and Posts

A low profile ±45°-polarized dipole antenna having an extremely wide bandwidth is proposed. Two crossed dipoles consisting of detached radiation arms are utilized as radiators and they are excited by dual simple striplines. Then several trapezoidal strips and four pairs of rectangular strips are utilized to improve the impedance matching over an exceedingly wide frequency band. For further improving the impedance and stabilizing the radiation pattern, four metallic posts are employed and located around the radiators. Another trapezoidal metal is finally added to the feed stripline of −45° polarization to improve the input impedance for −45° polarization. Our antenna has an extremely broad bandwidth of 80.4% (1.68–3.94 GHz) with VSWR < 1.5, isolation > 27 dB, and steady 3 dB beamwidth [half-power beamwidth (HPBW)] of 66° ± 8° in the operating band. The antenna has compact size of 0.32 λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">L</sub> × 0.32λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">L</sub> × 0.15 λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">L</sub> , where λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">L</sub> represents the wavelength at the lowest frequency of the operating band.

Textile Via-Loaded Bandwidth-Enhanced Half-Mode Substrate-Integrated Cavity Antenna for WLAN Communications

A textile via-loaded bandwidth-enhanced half-mode substrate-integrated cavity (HMSIC) antenna is presented in this article for wireless local area network (WLAN) communications. A strategy for adding shorting vias within the cavity is proposed based on the simulated <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${E}$ </tex-math></inline-formula> -field distributions of different modes of the HMSIC antenna. More specifically, the number and positions of vias are studied for maximum shift of lower resonance ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\rm TM_{1,1,0}^{HM}$ </tex-math></inline-formula> mode) so that it merges with higher resonance (rotated <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\rm TM_{2,2,0}^{HM}$ </tex-math></inline-formula> mode) to achieve a wide 10 dB return loss impedance band. Two prototypes of the designed structure are realized using textile manufacture techniques. A first realization uses embroidered sidewalls to create the cavity and metallic rivets for the shorting vias, and a second prototype uses embroidered vias and a stripline feed. The proposed antenna can operate from 5.09 to 5.9 GHz with a fractional bandwidth of 14.7% according to measurements. The simulated radiation efficiency is above 95% in free space and 82% when worn on the human body in the 5 GHz WLAN band (5.15–5.825 GHz).

A Compact Dual Linearly-Polarized Single-Plane Monopulse Antenna Array Based on SIW and Strip-Line Feed

A compact dual linearly polarized monopulse antenna array is proposed in this article. The size of the antenna array is <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$3.13\lambda _{0} \times 4.38\lambda _{0}$ </tex-math></inline-formula> , and it consists of two comparators, multilayer coupling slots, and a group of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$4\times $ </tex-math></inline-formula> 4 square patches. By using high-order-mode cavities and integrating the feeding network with the radiating part, the size of the antenna is considerably reduced. A prototype of the proposed antenna is fabricated and evaluated to the feasibility of the design. The measured total impedance bandwidth for four ports is 1.6% (18.65–18.95 GHz). The peak gains of the sum pattern with vertical and horizontal polarization are greater than 16.02 and 14.92 dBi, respectively. The null depths of the difference pattern at 18.8 GHz are less than −32 dB. The measurement results are in good agreement with the simulation results.

Wearable Wideband Circularly Polarized Array Antenna for Off-Body Applications

A wideband circularlypolarized (CP) wearable antenna for 5 GHz (5.15–5.825 GHz) wireless body area network is presented and analyzed. The emphasis of this work is on the additional resonance generated by the mutual coupling of a 2×2 compact patch array. As the proposed antenna is fed by a sequential-phase feeding network, the resonance can be used to achieve unidirectional radiation with improved CP bandwidth. To alleviate the loading effects of the human body, a modified strip feedline, comprising two pairs of arc-shaped slots cut on the bottom ground, is introduced. Moreover, the adoption of textiles as substrate and conductor provides flexibility and conformability, allowing the antenna to be integrated with garments. The prototype with the dimensions of 40 mm × 40 mm × 4 mm (0.73 <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">λ</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> × 0.73 <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">λ</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> × 0.07 <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">λ</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0</sub> ) was fabricated. The measured results indicate that a wide impedance bandwidth of 43% (4.25–6.63 GHz), a half-power beamwidth of 60°, and a 3 dB AR bandwidth of 34% (4.71–6.67 GHz) are achieved. Furthermore, the antenna performance is proved to be stable under structural deformation and human body loading. Finally, transmission losses and link budgets are evaluated, enabling the antenna to be a robust solution for off-body communications.

Same-Sense Circularly Polarized Grid-Slotted Patch Antenna With Wide Axial Ratio Bandwidth

In this communication, the same-sense circularly polarized grid-slotted patch antenna with wide axial ratio bandwidth (ARBW) is proposed. The rectangular grid-slotted patch on top and bottom planes are excited through flipped Z-shaped slots pair using a stripline feed to generate same-sense circular polarization with wider ARBW. Characteristic mode analysis is used in the design of the antenna to analyze the desired orthogonal modes. Variations of the resonant frequencies, ARBWs and local minimas with the design parameters are discussed. The antenna has a 3 dB ARBW of about 21% from 4.07 to 5.02 GHz, with the realized gain ranging from 2 to 3.5 dBic.

Substrate integrated waveguide antenna with dual rectangular slots for material characterization for ISM band applications

An antenna with small height and width with high input impedance filled with different slots is designed for ISM band applications. The substrate integrated waveguide antenna is designed with multiple different slots which produces ISM band applications. The rectangular cavity slots are introduced here. This will radiate a lower resonant frequency. In spite of using one rectangular slot two similar rectangular equally sized slots are introduced here for 2.4 GHz ISM band applications with a return loss of-13.20803 dB.The inset type of micro strip feed line is fitted to this backed slot antenna. The FR-4 substrate has been introduced for this back slotted antenna. The low profile compact antenna dimensions are 30 x30x1.6 mm3.The simulated antenna has been further designed with four different substrate for material characterization such as Polymide, Polyester, Teflon, Cotton. The antenna simulation is created using the CST Microwave Studio programme.

Design and Analysis of Reconfigurable Antenna for Wide Band Applications

The relevance of reconfiguration in a dynamic environment is to improve an antenna’s performance by allowing it to transition between multiple frequencies. In this paper, we designed a reconfigurable patch antenna and fed it by strip line feeding by placing 2 slots to obtain different resonant frequencies. The feature of reconfigurability is attained by using Pin Diodes. In our design, we take a 2 pin diode. The proposed Antenna can operate on different frequencies i.e. 2.88GHz, 5.5GHz, 10.8GHz and 11.1GHz with the efficiency of 90% and more at different conditions of the diodes. This analysis is done by using HFSS Software.

위성 Synthetic-Aperture Radar (SAR) 시스템용 X-밴드 이중 편파 마이크로스트립 패치 부배열 안테나

In this study, a high-performance, dual linearly polarized patch array antenna is presented for satellite synthetic aperture radar (SAR) applications. The antenna features an aperture-fed stacked patch as the radiation element and a stripline feeding network. A high-performance and low-loss dielectric substrate RF-35 by Taconic, and a honeycomb substrate is used. The honeycomb substrate is used to maximize the impedance bandwidth and decrease the insertion loss of the antenna. The proposed antenna offers exceptional isolation between the antenna’s ports in excess of 55 dB owing to its stripline feeding network. The via stitching technique is utilized to suppress the parallel-plate mode excited by the discontinuities in the stripline. The antenna is designed to possess a wide impedance bandwidth. A prototype antenna of size 2×4 elements, which operates in the X-band, is fabricated. Its impedance and radiation performance are experimentally verified, and the results are presented. The antenna exhibits a 15.7 dB peak gain and more than 40 dB of cross-polarization discrimination. In addition, a wide bandwidth of 19.4 % at a −10 dB return loss (RL) level is obtained.

Low-Profile, Broadband, Dual-Linearly Polarized, and Wide-Angle Millimeter-Wave Antenna Arrays for Ka-Band 5G Applications

A low-profile, broadband, dual-linearly polarized (dual-LP), and wide-angle millimeter-wave antenna array with beam-steerable capabilities operating in the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">Ka</i> -band is proposed for 5G applications. By jointly exploiting miniaturized vertically stacked elliptical patches, orthogonal aperture-coupled stripline feeding structures, and groups of shorting pins loaded close to the coupling apertures, the proposed dual-LP element has a small footprint of 4.5 × 4.5 mm with a total thickness of 1.57 mm, which exhibits a measured −10 dB impedance bandwidth of 21.8% and a mutual coupling below −41 dB. Wideband stripline-based Butler matrix circuits are designed and integrated with the 1 × 4 element array for verifying its broadband dual-LP multibeam radiation performance. Experimentally, the integrated array generates four beams with an angular coverage of about ±61° and ±75° for <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">x</i> - and <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">y</i> -polarizations, revealing that the proposed array is a promising candidate for 5G applications.

Broadband Circularly Polarized Microstrip Array Antenna With Curved-Truncation and Circle-Slotted Parasitic

This article presents a novel broadband circularly polarized microstrip array antenna for synthetic aperture radar system onboard Cessna 172 Aircraft. The antenna employs an 8×8 matrix formation with uniform element separation of 0.5λ and single-proximity-coupled strip-line feeding. The circular polarization wave generation uses a curved-truncation patch and a circle-slotted parasitic patch above it to realize the broadband circularly polarized antenna. The broadening of the axial ratio bandwidth (ARBW) applies a fully serial sequential rotation on the array feeding network. Meanwhile, the gain is improved using a circle-slotted parasitic patch with a floating cover on the top layer. The prototype antenna has a physical aperture of 270 mm × 300 mm with 1.1-kg weight. The prototype produces an impedance bandwidth of 1.5 GHz (29.3%), ARBW of 1.62 GHz (30.6%), a gain of 18.17 dBic, and aperture efficiency of 26%. The azimuth and elevation beamwidth achieved 12.7° and 13.0° at the center frequency, respectively.

A Miniaturized Broadband and High Gain Planar Vivaldi Antenna for Future Wireless Communication Applications

This paper presents a new miniaturized planar Vivaldi antenna (PVA) design. The proposed antenna structure consists of an aperture tapered profile and cavity stub fed with a simple 50 Ω strip line feeding network. The designed PVA offers versatile advantages, including the miniaturized size and simple design, and exhibited an outstanding performance compared to the latest reported literature. The antenna occupies a minimal space with an electrical size of 0.92λ0 × 0.64λ0 × 0.03λ0. The antenna achieves an excellent relative impedance bandwidth 117.25% at 10 dB return loss, peak realized gain of 10.9 dBi, and an excellent radiation efficiency of 95% at the specific resonances. The antenna’s optimal features, that is, broadband, high gain, and radiation efficiency, are achieved with efficient grooves based approach. Besides, the proposed antenna results are also analyzed in the time domain, which shows the excellent group delay performance &lt;2 ns in the operational band. The proposed antenna exhibited a stable far-field radiation pattern in orthogonal planes and strong distribution of current at multiple resonances. Simulation and the measured result show a good agreement. The proposed antenna has achieved optimal performance and is suitable for future wireless communication applications.

Esign of a 24GHz Rectangular Microstrip Patch Antenna for Wireless Application

The microstrip antenna required for higher frequency application is to be light in weight, easy to fabricate and small in size. As the applications in S-band and Ku-band are increasing with the increase in technology the requirement for higher data rate so the proposed work is to design a 24GHz (ka band) rectangular microstrip antenna with stripline feeding, return loss to be less than -20dB and VSWR less than 0.5. The substrate is chosen to be RT/duroid 5880 with relative permeability 2.2. it is capable of covering satellite application, telemetry. HFSS software tool is used to design the antenna.

Design and analysis of microstrip antenna with zig-zag feeder for wireless communication applications

This paper is presented a microstrip antenna with a zig-zag feeder for wireless communication, it has a wideband frequency spectrum (2-14) GHz. The proposed antenna is designed with a zig zag feed line which gave a wideband frequency and acceptable gain (7.448-5.928) dB, this antenna has zig zag slots printed in the ground plane on a lower side of the dielectric substrate, a certain form tuning stub is used to increase the matching between the feeder in the top layer of the substrate and ground plane in the bottom, this stub has an elliptical slot to performance matching input impedance with the feed line. The feeding technique used to feed this antenna is a strip feed line of 50 Ω. Different types of techniques are used to enhance the bandwidth of this antenna to get a wideband suitable for the requirements of the UWB antenna such as adjust the feed point position of the feed line with a tuning stub. All the radiation properties of the presented antenna are tested such as bandwidth, radiation pattern, and, gain.

SIW Cavity-Fed Filtennas for 5G Millimeter-Wave Applications

In this article, novel millimeter-wave (mmWave) filtennas (filtering antennas) are proposed to realize compact size and low insertion loss for 5G applications. It is achieved by employing eighth-mode substrate-integrated waveguide (EMSIW) cavities fully shielded by metallized vias and cover as resonators, which are named as fully shielded EMSIW (FSD-EMSIW) cavities. Interdigital coupling between cavities is introduced in order to obtain higher coupling strength for wideband operation. The proposed single-polarized antenna consists of a feeding stripline, two FSD-EMSIW cavities, and two stacked square patches, generating the four-order filtering antenna response. Furthermore, this design has been extended to realize a dual-polarized filtenna by employing double sets of feeding network. For demonstration, single-/dual-polarized filtenna prototypes were fabricated and measured, the measured results show that the 5G mmWave band (24.25-29.5 GHz) can be covered with average gains of 4.5 dBi. Good bandpass filtering response is also observed. Finally, to validate the proposed idea in array applications, a 16-element filtenna array is designed and measured with good performance.