Welding Stresses Research Articles

Improvement of Fatigue Characteristics of Friction Stir Welded A6061-T6 Applying Shot Peening

Recently, researchers have developed the method as a harmless the crack by the surface modification. For the purpose of contributing to reliability improvement of the A6061-T6 structure by harmless method, the following research was carried out: The tensile residual stress of friction stir welding was added by shot peening, resulting in a more significant compressive residual stress than that of the base metal. The effect of the surface crack aspect ratio on the maximum harmless crack depth (ahml) of A6061-T6 was evaluated for residual stress distribution. The detectable depth was evaluated in the relationship between ahml and the maximum detectable crack depth (aNDI) by non-destructive inspection (NDI).

Numerical and experimental analysis of temperature and residual stress of GTA and LASER welding for grade 91 steel

Numerical and experimental analysis of temperature and residual stress of GTA and LASER welding for grade 91 steel

Creep relaxation to relieve residual stress in girth-butt welded X80 pipelines: Simulation and experiment

The residual stress in girth-butt weld presents safety risks for large-diameter oil-gas pipelines, necessitating an in-depth investigation into the welding residual stress and the development of effective methods to mitigate these stresses, thereby enhancing structural integrity. In this work, a finite element girth-butt welding model was developed to predict the residual stress of X80 pipelines. The residual stress relief resulting from local post-weld heat treatment (PWHT) was simulated based on the Norton creep model applicable to X80 steel. The simulation results, encompassing the residual stress both before and after PWHT, were validated through blind-hole drilling measurements. The results demonstrate that the welding residual stresses across all orientations were significantly reduced following PWHT, with a maximum stress reduction of approximately 360 MPa. The primary mechanical mechanism for residual stress relief was identified as high-temperature creep, and it was concluded that the PWHT alleviated welding residual stress effectively when the heating temperature exceeded the creep activation temperature. The consistency between the finite element analysis results and the experimentally measured residual stresses affirms the validity and feasibility of the finite-element-based approach for predicting welding residual stresses.

Simulation-based analysis of welding process parameters for TC4ELI titanium alloy thick-walled cylinders

Abstract In this paper, ABAQUS is used to numerically simulate the residual stresses during welding of titanium alloy thick-walled cylinders. A detailed simulation analysis of the stress field during the welding process is performed by establishing an accurate finite element model, defining the thermal physical properties, boundary conditions, and heat source model, and using the indirect heat-force coupling method. The results of the study show that the distribution of the weld stress field has an important influence on weld quality, material properties, and structural strength. The movement of the welding heat source results in a dynamic change in the stress field, which gives rise to a significant stress concentration at and in the vicinity of the welding heat source.

Experimental evaluation of multiple-component residual stress distribution in a dissimilar metal repair joint of ferritic/martensitic steel using the asymmetric-cut and the symmetric-cut contour method

A thick multi-pass butt-welded ferritic/martensitic steel (P91) joint is prepared and the local region of the weld is repaired with an ENiCrFe-3 nickel-based alloy using the manual metal arc welding method. The repair weld including part of the base metal is then subjected to ultrasonic impact treatment (UIT). A three-cut contour method, including two asymmetric cuts and one symmetric cut, is developed in the present study to obtain the two-dimensional residual stress distributions at different locations, and the stress release after multiple cuts is considered to get the original stress distribution before cuts. The measurement procedure is introduced in detail. The longitudinal stresses in the repair weld and the initial weld of the P91 steel joint, as well as the transverse stress at the weld center, are finally obtained. The effects of the dissimilar metal repair weld at the local region on the longitudinal and transverse welding residual stresses are investigated. In addition, the applicability of UIT to mitigate the surface stress in nickel-based alloy repair weld is analyzed. The results show that the transverse and longitudinal stresses in the nickel-based alloy repair weld are both tensile stresses, the maximum longitudinal stress is close to the yield strength of the B91 weld metal and occurs in the heat-affected zone of the repair weld located in the initial weld. Repair welding causes the internal transverse compressive stress region to be narrower than in the original weld. UIT can be used to introduce compressive stress to the surface layer of the nickel-based alloy repair weld.

An experimentally validated thermomechanical model for a parametric study on reducing residual stress in cast iron repair welding

Remarkable casting properties and superior mechanical characteristics of cast iron make it an ideal material for a wide range of industrial applications. However, the production of cast iron components may result in the formation of cracks and defects, posing a significant threat to their structural integrity. Repair welding is a promising solution to resolve cast iron production defects. However, repair welding cast iron components poses unique challenges that stem from residual stress (RS) formation and the possibility of cracking during the repair process. Moreover, research on cast iron repair is scarce. To overcome these challenges, this paper presents a thermo-mechanical model validated by experiments to reduce RS in cast iron repair welding through the optimization of welding parameters and weld sequences as well as the geometry of the repair area. An experimental bead-on-plate weld is set up in order to validate the developed thermo-mechanical model. The temperature distribution in the weld is measured using thermocouples placed around the weld line. An X-ray diffraction technique is used to measure the axial and transverse RS at different points around the weld line. The developed finite element model is employed to simulate the repair welding process and analyze the effect of inter-pass temperature, the number of welding passes, welding sequences, and groove geometry on the RS. The numerical approach applied in this study provides a framework for repair welding optimization of cast iron and other materials, fostering the development of more efficient and reliable repair methods for industrial applications.

Tuning residual stresses in welded structures by exploiting bio‐inspired suture interfaces

AbstractNature offers a valuable source of inspiration when designing optimized structures. For instance, when two or more shells are joined during growth processes, Nature prefers to exploit interlocking paradigms to enhance the strength of the bond—cranial sutures are one example. Mimicking this distinctive characteristic when welding thin metallic elements may offer some structural benefits. The present study theoretically investigates the possibility of mitigating the detrimental tensile residual stress that always originated by welding processes, by exploiting Computational Welding Mechanics. Specifically, two plates joined by laser welding following sinusoidal paths (i.e., wave‐like), alongside a linear one, will be studied and compared. Thanks to the distinctive temporal and spatial heat distributions of sinusoidal welding, both welding stress and strain develop in dissimilar ways compared with linear path welding—this is reflected to the resulting weldment distortion too. The results show that geometrically optimized sinusoidal welding can effectively reduce residual stress magnitudes compared with the linear configuration counterpart. The implications of these findings are of particular interest when dealing with the structural performance of welded structures, especially in fatigue contexts.

High strain rate tensile deformation of similar and dissimilar AA6082 and AA7075 friction-stir-welded blanks

Friction-stir-welding process has become an established solid-state technique for joining of dissimilar lightweight materials over the past decade by overcoming fundamental welding challenges such as solidification cracking, phase segregation and surface oxidation. Despite these unique capabilities, the resulting microstructure feature in the weld zone consisting of fine grains with a high dislocation density, challenges further heat treatment and forming processes. Hence, a high solution annealing temperature results in degradation of the adjusted microstructure and in a lower to reduced mechanical properties in case of dissimilar joints of precipitation-hardenable aluminum alloys. Subsequent hot forming therefore involves a great effort and requires further heat treatment steps. Thus, the present study investigates the effect of a recently introduced novel thermo-mechanical forming process on local deformation behavior of similar as well as dissimilar joints processed by friction-stir-welding technique of thin-walled AA6082 and AA7075 blanks. To avoid the complete elimination of the adjusted microstructure, the welding process is performed after a thermo-mechanical process consisting of solution annealing, die cooling and peak aging. Uniaxial tensile tests are then carried out at high strain rates ranging from ε˙ = 40 s-1 to ε˙ = 400 s-1. The results show an increase in yield and ultimate tensile strength as well as in total elongation after failure with increasing strain rates. As the strain rate increases, the flow stress of similar weld of AA7075 is higher than those of AA6082 and the dissimilar weld of AA6082 and AA7075. Local deformation measurements reveal higher strain localization in the welded zone for similar welds, which leads to micro-crack initiation and failure due to strain accumulation. Microstructure analysis shows very fine equiaxed grain structure in the nugget zone and homogenous distribution of precipitates after friction stir welding process, which explain the plastic deformation behavior.

Effects of ultrasonic vibration on residual stress distribution and local mechanical properties of AA6061/Ti6Al4V dissimilar joints by resistance spot welding

The joining of dissimilar titanium and aluminum alloys has potential applications in railway and aerospace industries, owing to substantial weight reduction and better economic viability. In this study, the residual stress distribution and local mechanical performance of ultrasonic-assisted resistance spot welding (UaRSW) welds were investigated. The welding current, welding time, and electrode force of the RSW process were set as 9.0 kA, 350 ms, and 1.0 kN respectively, and the frequency and power of ultrasonic vibration were 20 kHz and 800 W. The residual stress was evaluated by X-ray diffraction (XRD) method and numerical simulation, and these methods showed a reasonable match. There was tensile residual stress distributed on RSW welds and UaRSW welds, but the value of residual stress was reduced by about 30% at welding nugget and 20% at heat affected zone (HAZ) with the ultrasonic vibration, the reduction of residual stress in UaRSW welds was attributed to the more uniform temperature distribution and lower plastic deformation resistant of AA6061. The welding peak temperature was decreased from 1673.4 °C to 1584.2 °C with the ultrasonic vibration, resulted from the modified Al/Ti contact surface and reduced contact resistance. The miniature tensile test results showed the improvement of mechanical performance by ultrasonic vibration. The maximum load of welding nugget region increased from 19.6 N to 22.3 N, and the elongation obtained 10% increase. This hybrid welding technique shows a potential to improve the quality of welds with ensured efficiency, which is also simple to realize automation in the manufacturing industry.

Influence of Process Parameters on Residual Stresses in Dissimilar Friction Stir Welding of Aluminum Alloys

Foreseeing how welded structures will behave requires careful consideration of the residual stresses that the friction stir welding (FSW) process introduces. These residual stresses can cause severe deformation and compromise the ability of friction stir welded structures to bear imposed external loads. This work uses a Sequentially Coupled Thermo-mechanical finite element simulation to quantitatively evaluate the influence of such residual stresses coming from the FSW process. This modelling method examines the thermal and post- weld stress distributions during the friction stir welding of dissimilar AA2024-T3 and AA5086-O alloys. The procedure entails an initial thermal analysis followed by a mechanical analysis to determine the distribution of residual stresses across the entire dissimilarly welded alloys. The study examined how alterations in FSW operational parameters, such as rotational and translational speeds, influence both the thermal conditions and residual stress distribution. The findings highlighted that both temperature and residual stress exhibited higher values on the retreating side of the specimen compared to the intended advancing side. As the tool rotational speed rose, the magnitude of longitudinal residual stress dropped, however it showed an increase with greater tool translational speeds. Moreover, the simulated outcomes demonstrate the substantial impact of welding fixtures on the profiles and magnitudes of residual stresses.

Influence of welding sequences and boundary conditions on residual stress and residual deformation in DH36 steel T-joint fillet welds

This paper aims to investigate the influence of welding sequences and boundary conditions on welding-induced residual stress and residual deformation of DH36 steel T-joint fillet welds through experimental and numerical methods. A series of typical experiments of successive and simultaneous double-sided welding conditions are conducted to explore both the magnitude and distribution of temperature field, residual stress and residual deformation. Meanwhile, thermal elastic-plastic finite element analysis based on a double ellipsoidal heat source model is performed to investigate the heat transfer and deformation mechanism during the welding process. The influencing factors are further explored to determine and quantify the residual stress and residual deformation induced by different welding sequences and boundary conditions. There is generally well agreement between the experimental and numerical results in terms of temperature field, residual stress, residual deformation and molten pool morphology. The results show that the welding sequences have an important influence on the magnitude and distribution of residual stress and residual deformation. Continuous simultaneous double-sided welding can significantly reduce residual stress and residual deformation to obtain better-quality welds. Boundary conditions have a significant effect on the distribution and magnitude of residual deformation and little effects on residual stress. Tightening the ends of the flange plate with bolts during the welding process can significantly reduce the deformation.

Pengaruh Perbedaan Ayunan Pengelasan Dengan Metode SMAW Terhadap Kekuatan Tarik Pada Baja ST 37 Strip 5 MM

The purpose of this study was to see the effect of differences in welding swing on the tensile strength of 5 mm strip iron. The number of research samples was 6 pieces divided into two groups, the first group of 3 pieces welded with zig-zag welding swing, the second group of 3 pieces welded with spiral welding swing. The tensile test object used a tensile testing machine to determine the tensile stress value of the welding swing of each test object by slowly applying a load or force until the test object broke. This research method uses quantitative with a comparative experimental approach. The results of the welding tensile stress test of each test object sample welded with zig-zag and spiral welding swing joints showed that there was a similarity in the tensile test data, namely normal distribution, and similarity in variance. Hypothesis testing was obtained from the results of the tensile stress test of SMAW welding results with zig-zag and spiral welding swings showing a Tcount value of -8.021 (dk) = n1 + n2-2 at a significance level of 0.01 or 1%, a Ttable of 4.604 was obtained. So that the magnitude of the tensile stress of SMAW welding results with zig-zag and spiral welding swings has no significant influence.

Effect of post-weld heat treatment on microstructure and mechanical properties of twinning-induced plasticity (TWIP) steel joints

The effect of post-weld heat treatment on microstructure and mechanical properties of twinning-induced plasticity (TWIP) steel joints obtained by melting electrode inert gas-shielded welding (MIG welding) was systematic studied. A total of two post-weld heat treatment processes are proposed, i.e., post-weld annealing treatment (PWAT) with temperature/time of 1100 ℃/1 h and subsequent furnace cooling and post-weld solution treatment (PWST) with temperature/time of 1100 ℃/1 h and subsequent water quenching, which were compared with the case of post-weld non-treatment (PWNT). Following annealing treatment at 1100°C, the joint tensile strength dropped by 6.6 % (from 845.46 MPa to 789.85 MPa), while its elongation at break increased by 40.87 % (from 29.80 % to 41.98 %). The significant increase in plasticity was due to the significant elimination of weld stresses in the joints after annealing. Moreover, the stresses in the weld metal of the PWST joints were instead significantly elevated and the carbides were solidified, which resulted in the lower strength. When post-weld heat treatment was applied, the impact toughness of the joints was lower than when untreated. This was primarily due to the greater percentage of the low-angle grain boundaries and the precipitation of MC-type carbides. Consequently, post-weld annealing treatment was an effective method to further enhance the strong plasticity of new twinning-induced plastic steel joints.

Analysis and simplified model calculation of residual stress in U-rib welding of steel bridge deck

Analysis and simplified model calculation of residual stress in U-rib welding of steel bridge deck

Numerical and experimental investigation of the effect of heat input on weld bead geometry and stresses in laser welding

Abstract Nowadays, laser welding is a powerful joining method. Thanks to the advantages it has, its usage area is increasing day by day. However, getting the desired result from the laser welding process is possible with the proper welding parameter selections. Otherwise, many problems may be encountered, including significantly incomplete penetration. For this reason, parameter selection has been discussed in many studies in the literature. At this point, validated numerical simulation models are precious. Since these models reduce experiment costs and save time. Especially numerical simulation of the structural steel, which is the one of most used materials, is crucial. In this study, the effects of laser power (LP) and welding speed (WS), which are among the vital parameters of laser welding, on weld width and stress were investigated numerically and statistically. Structural steel was selected as the material, and the Taguchi method was carried out for the simulation case study design. Simufact Welding software was used for simulation studies, and simulations were carried out thermomechanical. Thus, more realistic results were obtained via the thermomechanical method. One of the simulation results was verified through an experimental study. The results were evaluated with signal-to-noise (S/N) ratio and a statistical analysis of variance (ANOVA), and as a result of the study, it was seen that the welding speed was a more effective parameter, the optimal parameter combination was found to be 3500 W for laser power and 40 mm/s for welding speed to get maximum weld width and minimum equivalent stress. In addition, it was observed that correctly created simulation studies may provide very close results to experimental studies.

Influence of heat input and preheating on residual stresses in pipe weld

AbstractUsing finite element methods, residual stresses were estimated in pipe welds. Experiments were also conducted to verify the numerical results. An alternative to a three-dimensional model was used to simplify the numerical calculation for residual stresses investigation. Model predictions were validated by measuring residual stresses using X-ray diffraction. As compared to measured residual stress distributions, the computational approaches developed in this study can accurately predict welding residual stress distributions. The focused welding parameters have a significant impact on residual stresses even when all the other parameters are the same.

Investigation of reduction of residual welding stresses because of ultrasonic treatment of a welded joint at a frequency of 20, 37 and 44 kHz

Investigation of reduction of residual welding stresses because of ultrasonic treatment of a welded joint at a frequency of 20, 37 and 44 kHz

Investigating parameters and ultimate load-bearing performance of novel anchor-box type cable–girder anchoring structure for large-span cable-stayed bridges

This study combined experimental research and finite element numerical simulations to investigate the ultimate bearing performance of a novel anchor-box-type cable–girder anchorage structure for large-span cable-stayed bridges. The stress distribution and deformation in the structure was assessed under varying loads, and the effects of the construction parameters on peak stress in key load-bearing welds were analyzed. The proposed design exhibits a safety margin of 3.2. The simulated and experimental stress distributions agree well with experimental data, although deformation and load-bearing capacity results are non-conservative. The maximum stress in the main load-bearing welds exhibits an exponential relationship with construction parameters.

Estimation of residual stress in dissimilar metals welding using deep fuzzy neural networks with rule-dropout

Welding processes are used to connect several components in nuclear power plants. These welding processes can induce residual stress in welding joints, which has been identified as a significant factor in primary water stress corrosion cracking. Consequently, the assessment of welding residual stress plays a crucial role in determining the structural integrity of welded joints. In this study, a deep fuzzy neural networks (DFNN) with a rule-dropout method, which is an artificial intelligence (AI) method, was used to predict the residual stress of dissimilar metal welding. ABAQUS, a finite element analysis program, was used as the data collection tool to develop the AI model, and 6300 data instances were collected under 150 analysis conditions. A rule-dropout method and genetic algorithm were used to optimize the estimation performance of the DFNN model. DFNN with the rule-dropout model was compared to a deep neural network method, known as a general deep learning method, to evaluate the estimation performance of DFNN. In addition, a fuzzy neural network method and a cascaded support vector regression method conducted in previous studies were compared. Consequently, the estimation performance of the DFNN with the rule-dropout model was better than those of the comparison methods. The welding residual stress estimation results of this study are expected to contribute to the evaluation of the structural integrity of welded joints.

Study on the Effect of Preheating Temperature on Residual Stress in Laser Arc Composite Welding of Dissimilar Aluminum Alloys

Study on the Effect of Preheating Temperature on Residual Stress in Laser Arc Composite Welding of Dissimilar Aluminum Alloys