Standard Installation Research Articles

Combustion of liquid hydrocarbon fuels sprayed into gas generation chamber with superheated steam as low emission technology for energy production

Experimental and numerical studies were conducted to scientifically validate the Steam Injection Method with Gas Generation chamber (SIMGG) as a low-emission combustion technology for energy production in low and medium power boilers using different types of fuels. For the first time, a fully functional prototype of a burner implementing SIMGG was tested under the conditions of a standard low-power boiler installation, and combustion characteristics of fuels with various physical properties (diesel fuel and a mixture of used automotive oils) were obtained under different operating parameters. The results of the studies show that using SIMGG reduces carbon monoxide (CO) and nitrogen oxides (NOx) emissions by up to half or more under closed-combustion conditions for various fuels. The lowest total emissions of CO and NOx are achieved at an air excess coefficient of 1.2 and a steam-to-fuel ratio of greater than 0.66.

Dimensional synthesis of motion generation of a planar four-bar mechanism

A motion generation method for a planar four-bar mechanism without prescribed timing is proposed in this article. A characteristic of coupler points is found: for the coupler points of a four-bar mechanism in a standard installation position rotated by the corresponding input angle clockwise around the origin of the Cartesian coordinate system xOy, the generated points lie on the feature coupler circles. Next, based on this, the design process is divided into three steps. In the first step, the relative input angles, the relative coupler angles and five geometric parameters of the desired four-bar mechanism are optimized. In the second step, the basic dimensional types and initial input angle are determined, and then, the input angles are obtained. In the third step, the real size of the desired linkage mechanism is calculated. Because the dimension of the design variables in each step is exceptionally small, the motion synthesis method can yield design solutions with high precision in a short time. Six comparison examples are presented to demonstrate the efficacy of the proposed method. In addition, the method is used to design a robot for lower limb rehabilitation for application to the human foot.

Analysis of Greywater Recovery Systems in European Single-Family Buildings: Economic and Environmental Impacts

This study explores the integration of greywater recovery systems (GRSs) within single-family buildings across European countries. The analysis evaluates the impacts of these systems from multiple perspectives: potable water conservation, economic feasibility, energy consumption, and environmental impact. Employing life cycle cost (LCC) and net present value (NPV) analyses, the research assesses the economic viability of these systems compared to standard water installations. Positive NPV is observed in countries such as Belgium, Germany, Denmark, Finland, and Norway, according to the base scenario. Additionally, the implementation of subsidies can enhance economic incentives for adopting GRSs by reducing the payback period (PBP). Significant findings include reductions in potable water demand by up to 43.0%, and energy savings of up to 42.6% are also observed with the use of GRSs. Additionally, notably lower carbon dioxide emissions (CDEs) were reported, with reductions being directly proportional to the decreases in energy use. This holistic approach aims to establish frameworks for decision-making processes, emphasizing that economic and environmental aspects are mutually complementary and significant.

Pelatihan Redesain Instalasi Listrik Untuk Program Konversi Kompor Gas LPG Ke Kompor Listrik Di Desa Nyurlembang

The allocation of LPG gas subsidies has increased, putting a burden on state finances, while surplus electricity production is not being utilized optimally. Electrical energy can replace LPG gas by replacing the gas stove with an electric stove. This conversion requires adequate installation to ensure the safe and secure operation of the electric stove. The implementation of the conversion program must be supported by community readiness regarding standard electrical installations for electric stoves in the form of training. Training activities were carried out in Nyurlembang Village, Narmada, West Lombok, as a community service activity. This activity aims to educate and train the public about repairing and redesigning electrical installations for electric stoves. Training methods include lecture, discussion and practice methods. Before and after the activity, participants are given a written test to determine the success of the training activity. The test results show an average score before and after training of 38.33 and 66.00 for the range 0-100. These results show that the training was quite effective with an increase in participants' theoretical and practical knowledge of 27.67.

Large-Scale Performance Evaluation of Various Woven Silt Fence Installations under Nebraska Highway Conditions

Sediment barriers are used on construction sites to protect downstream waterbodies from the impacts of sediment-laden stormwater runoff. Although ubiquitous on construction sites, many sediment barrier practices lack performance-based testing to determine effectiveness and treatment mechanisms, with previous evaluations being limited to conditions local to the Southeastern U.S., with conditions in other regions remaining untested. Testing was conducted to determine the effectiveness of woven silt fence barriers and provide structural improvements to common installation methods. Testing was conducted using a large-scale sediment barrier testing apparatus at the Auburn University—Stormwater Research Facility. The results from testing indicate that Nebraska DOT standard silt fence installations can be improved to reduce the risk of structural failures such as undermining, complete installation failure, slow dewatering, and overtopping. To improve structural performance, four modifications (a 15.2 cm [6 in.] offset trench, wooden posts, a dewatering board with an overflow weir, and a dewatering board with an overflow weir with adjusted post spacing) were tested. On average, 83% of introduced sediment was retained behind the tested barriers. The water quality results across the testing of standard and modified installations indicated that stormwater treatment was due to sedimentation within the impoundment formed by silt fence installations and not filtration through geotextile fabric.

Design and Simulation of a Solar Powered House in Muğla: Roof Decorated with Half Cut Cells

In this article, the performance, design and efficiency calculation of photovoltaic systems were made using PvSol program. For roof type panel design close to standard installations, panel position and panel type were designed based on Muğla province sun hour data and roof shading factor. In this study, the data obtained for the roof type installation designed in Muğla city using monocrystalline, polycrystalline and half-cut monocrystalline cells were compared. When yield, area and price parameters were compared, it was found that the best cell type was half-section monocrystalline. As a result of the simulations, it was found that the average daily energy need of the house is 6.4kWh, fed by 14 half-section monocrystalline panels. The results obtained are consistent with the data in the literature.

Exploring the Impact of Artificial Intelligence on Global Health and Enhancing Healthcare in Developing Nations.

Artificial intelligence (AI), which combines computer science with extensive datasets, seeks to mimic human-like intelligence. Subsets of AI are being applied in almost all fields of medicine and surgery. This review focuses on the applications of AI in healthcare settings in developing countries, designed to underscore its significance by comprehensively outlining the advancements made thus far, the shortcomings encountered in AI applications, the present status of AI integration, persistent challenges, and innovative strategies to surmount them. Articles from PubMed, Google Scholar, and Cochrane were searched from 2000 to 2023 with keywords including AI and healthcare, focusing on multiple medical specialties. The increasing role of AI in diagnosis, prognosis prediction, and patient management, as well as hospital management and community healthcare, has made the overall healthcare system more efficient, especially in the high patient load setups and resource-limited areas of developing countries where patient care is often compromised. However, challenges, including low adoption rates and the absence of standardized guidelines, high installation and maintenance costs of equipment, poor transportation and connectivvity issues hinder AI's full use in healthcare. Despite these challenges, AI holds a promising future in healthcare. Adequate knowledge and expertise of healthcare professionals for the use of AI technology in healthcare is imperative in developing nations.

The thermal and stored heat energy driving a Stirling engine for power generation

South Africa’s national power grid is currently in dire straits. The lack of a dependable power supplier and rising electricity costs force the public and businesses to look for alternatives to meet their energy needs. These alternatives are costly to implement and beyond the financial reach of most South Africans. The most common alternative energy source is solar photovoltaic systems with large battery banks to survive Eskom's long, regular load-shedding schedules. This research aims to design and simulate a combined solar-thermal and stored heat energy-powered Stirling engine for power generation. The output of the research simulation was compared to a standard photovoltaic installation of similar power output. The results for this paper were generated from the simulation software package MATLAB. Such a system must have a lower capital cost to compete with solar photovoltaic systems with battery backup. The Stirling system was found to be cheaper than the deep-cycle gel system and about 11% cheaper than the PV system using lithium iron phosphate.

Wear characteristics analysis of variable hyperbolic circular-arc-tooth-trace cylindrical gear transmission considering assembly error theory

Wear is the main failure form of the gear transmission interface, runs through the whole life cycle of gear service, and the distributed error of the tooth surface due to the introduced assembly error will make the actual meshing state of the tooth surface different from the ideal meshing state, thus affecting the tooth surface wear trajectory and state. Therefore, considering the coupling relationship between assembly error and tooth surface contact analysis, the variation laws of the wear amount of the gear transmission interface of the variable hyperbolic circular-arc-tooth-trace cylindrical gear were studied under the consideration of assembly error in this article. Based on the tooth surface contact analysis method and Hertz contact theory, the transient linear load, the combined radius of curvature, the length axis and short axis of the contact ellipse, and the instantaneous sliding velocity were calculated. Through revising the calculation method of adhesive wear of variable hyperbolic circular-arc-tooth-trace cylindrical gears, the correlations between the tooth surface wear amount and gear parameters of variable hyperbolic circular-arc-tooth-trace cylindrical gears under different assembly errors were analyzed. The results show that the maximum wear occurs at the root of the tooth, and the wear at the indexing circle approaches zero, whether it is standard installation or non-standard installation. The vertical axial error and horizontal axial error have little effect on the wear, while the center distance error will aggravate the wear. The proposed method comprehensively considers the influence of assembly error and gear parameters on tooth surface wear, and this method can provide a theoretical reference for the design and analysis of anti-wear, wear reduction, and life extension of variable hyperbolic circular-arc-tooth-trace cylindrical gear tooth surface.

Dimensional synthesis of motion generation in a spherical four-bar mechanism

A new objective function for optimizing spherical, four-bar mechanisms for motion generation is presented. Rigid-body poses of a spherical four-bar mechanism in a standard installation position are investigated, and a normalization processing method is proposed. After processing the coupler points of the mechanism, the feature points generated are located on the circles. The formation principle of the feature coupler circles is analysed, and the internal relationship between the centre angle of the adjacent feature points on the feature coupler circles and the coupler angle of the spherical four-bar mechanism is determined. An input angle determination method is proposed for the spherical four-bar mechanism in a general installation position. An objective function is then established to optimize the basic dimensional types, relative input angles, and installation position parameters of the desired spherical four-bar mechanism. The proposed method is applicable to both prescribed and unprescribed timing problems. Notably, the dimension of the optimization variables is only eight, which is exceptionally low for multiple position motion generation without prescribed timing; therefore, the global optimal solution is more easily obtained. The optimization process is carried out by the genetic algorithm. The feasibility and effectiveness of our proposed method are demonstrated by examples.

Development of Polyhydroxybutyrate-Based Packaging Films and Methods to Their Ultrasonic Welding.

This study developed a technical task associated with the formation of welded joints based on biodegradable polymers and their subsequent physicochemical characterization. The primary objective was to establish the effect of the welding process and modification of natural poly(3-hydroxybutyrate) (PHB) with N,N-dibutylundecenoylamide (DBUA) as a plasticizing agent on the structure and properties of PHB-based biopolymer materials as well as the process and structure of welded joints formation using ultrasonic welding technique. The weldability of biodegradable layers based on PHB and PHB/DBUA mixture was ultrasonically welded and optimized using a standard Branson press-type installation. The effect of the DBUA plasticizer and welding process on the structure of PHB-based biodegradable material was investigated using scanning electron microscopy, X-ray diffraction, FT-IR spectroscopy, differential scanning calorimetry, and thermomechanical analysis. The results confirmed that the DBUA acted as an effective plasticizer of PHB, contributing to lower crystallinity of the PHB/DBUA mixture (63%) in relation to the crystallinity degree of pure PHB film (69%). Ultrasonic welding resulted in an additional increase (approximately 8.5%) in the degree of crystallinity in the PHB/DBUA in relation to the initial PHB/DBUA mixture. The significant shift toward lower temperatures of the crystallization and melting peaks of PHB modified with DBUA were observed using DSC concerning pure PHB. The melt crystallization process of PHB was affected by welding treatment, and a shift toward higher temperature was observed compared with the unwelded PHB/DBUA sample. The butt-welded joints of biodegradable PHB/DBUA materials made using the ultrasonic method tested for tensile strength have damaged the area immediately outside the joining surface.

127 Photochemical Aging Increases Toxicity of EURO 6 Gasoline Car Exhaust in Lung Epithelial Cells at the Air-Liquid Interface

Abstract Traffic emissions contribute to ambient air pollution, posing a threat to human health. The installation of stricter exhaust emission standards and particle filters led to a significant decrease of particulate matter emissions by cars. However, little is known about how atmospheric transformation changes the toxicity of exhaust emissions from modern cars. We evaluated the physico-chemical properties and toxicological effects of fresh and photochemically aged aerosols from a gasoline EURO 6 car equipped with a particulate filter. A549 alveolar and BEAS-2B bronchial epithelial cells were exposed for 4h to aerosols at the air-liquid interface. The toxicity was determined by measuring cell viability, cytotoxicity, oxidative stress, primary and oxidative DNA damage. Particle number concentration (PN) in fresh aerosol was negligible while photochemical aging with an equivalent photochemical age of 5 days led to PN of 6.6´106 cm-3 with a mean size of 35 nm. Secondary aerosol particles predominantly consisted of organic matter, nitrate, and ammonium, which were formed by the oxidative gas-to-particle conversion of volatile organic compounds (VOCs), particularly aromatic hydrocarbons, and NOx in the exhaust. Significant levels of oxygenated VOCs were also detected. Fresh aerosol caused no cytotoxicity in lung cells, but led to slight DNA damage whereas aged aerosol caused toxicity to both cell models, oxidative stress and oxidative DNA damage mainly due to the gas phase. Our results indicate a significant toxification of the emissions by photochemical aging. This calls for considering atmospheric processes in future exhaust emission standards for the transport sector toward health effect-driven emission regulations.

Adhesion Strength Analysis of Synthetic Polymer Rubberized Gel on Diversely Wetted Concrete Surfaces

In this study, the relationship between viscosity of synthetic polymer rubberized gel (SPRG) used for waterproofing and adhesive strength on varying degrees of wetted surfaces is examined. First, SPRG specimens of different ratios of viscosity modifiers were prepared (3% to 10%, interval of 1% per specimen type). These specimens were installed onto substrate surfaces of varying degrees of humidity ratio (0%, 10%, 20%, 30%, 50%, 70% and 100%). Upon following the standard installation procedure of the SPRG specimens, standard pull-off tests were conducted. Results of the test showed that a consistent relationship exists between the viscosity of synthetic polymer rubberized gel (SPRG) and its adhesive strength on different degrees of wetted surfaces. Linear regression analysis and subsequent calculation of the respective coefficient of determination leads to the result that viscosity is a relevant factor for achieving stable adhesion when it comes to the usage of SPRG waterproofing. The findings of this study could have significant implications for the development and application of adhesive gel waterproofing materials in various industries.

Distributed fibre optic inclinometer with cloud-based monitoring system

Geotechnical instrumentation and monitoring are important aspect of controlling subsurface ground movement, particularly in deep excavations and forewarning of geological disasters such as landslides, land subsidence, ground fissure, and surface collapse. A borehole inclinometer is an example of the established method to monitor such ground movements. For real-time data, a series of in-placed inclinometer probes are installed inside the borehole casing to provide the lateral displacement response over time. The limitation of the conventional system is the high cost and the practicality of inserting a high number of sensing probes into the casing for better measurement accuracy. Recent advancement in Distributed Optical Fibre Strain Sensing (DOFS) enables the incorporation of DOFS as a fibre optic (FO) inclinometer with lateral displacements to be plotted at centimetres spacing and is unaffected by the gauge lengths between the probes. This study enhances the FO inclinometer by developing a web-based application (SmartGeopipe©) to automate data acquisition which also includes complex data processing for the final pipe deflection profile visualisation. The FO inclinometer comprised of optical cables attached externally onto a remodified inclinometer casing and connected to a Brillouin Optical Time Domain Analysis (BOTDA) strain analyser. A standard installation procedure was established to safely secure the sensors during the casing installation process inside the borehole. SmartGeopipe© software is written using a predominantly monolithic Python / Cython backend and a multi-page frontend built with HTML, CSS, and JavaScript ES5 languages. All the computation work and data storing are done in a cloud server and SQL database, respectively. A case study of a station box excavation as part of the Mass Rapid Transit (MRT) tunnelling project was chosen to validate the performance of the FO inclinometer and the web application. Data from the FO inclinometer corroborated well with the manual measurements of the inclinometer probe. This ability supports the realization of an early warning system as an engineering control for hazard management in civil engineering infrastructure projects.

Demonstration of 12 Years Outdoor Working of Highly Durable Dye-Sensitized Solar Cell Modules Employing Hydrophobic Surface Passivation and Suppression of Biased Distribution of Iodine Ions

Dye-sensitized solar cells (DSCs) outperform conventional silicon solar cells in terms of weight and design flexibility. Therefore, besides standard rooftop installation, DSCs are suitable for new applications, including windows and walls. However, insufficient durability remains a critical issue, and outdoor working over 10 years is yet to be realized. In this study, we developed two approaches to improve the durability. The first involves hydrophobic surface passivation on the TiO2 surfaces by adopting alkylbenzimidazole (CnH2n+1BI) with long alkyl chains instead of the conventional additive (N-methylbenzimidazole) used for high open-circuit voltage in an ionic liquid-based electrolyte. The additive with a suitable alkyl-chain length (N-butylbenzimidazole and N-hexylbenzimidazole) notably improved the resistance against infiltrating water. The second approach refers to the DSC module arrangement. A unique problem of large-sized modules is that the I3– distribution often becomes biased over time, lowering the conversion efficiency. Horizontal module arrangements and/or the strip-shaped single cells in the modules solved this problem. By adopting these two approaches, we have demonstrated that the 10 cm × 11 cm-sized DSC modules have high durability to maintain 75% of their initial performance after the 12 year outdoor working test. This is the longest demonstrated lifetime for DSC modules outdoors.

Classroom mock-up meeting Standard S12.60

The Acoustical Society of America (ASA) developed a standard entitled Acoustical Performance Criteria, Design Requirements, and Guidelines for Schools (ASA/ANSI S12.60-2010) that provides a minimum set of requirements to help school planners and designers “provide good acoustical characteristics for classrooms and other learning spaces in which speech communication is an important part of the learning process.” In this revision, several details were revised for incorporation into building codes. Despite the obvious benefits of quieter classrooms, incorporating the standard into building codes met with resistance. A common perception was that in order to meet the standard’s requirements, specialized HVAC equipment and installation methods would be necessary, resulting in an installed cost beyond what most schools could afford. Acoustical prediction tools indicated that the requirements could be met using standard HVAC equipment and installation methods. To verify the predictions, a simulated classroom was built and several common types of equipment including a single-zone air handling unit, a high-efficiency water-source heat pump, and a packaged rooftop unit were tested. The selected products were standard catalog offerings, without any special attenuation features, that were operated at typical airflow and static pressures. This paper describes those tests, the conclusion, and the resulting recommendations.

Safety, tolerability, and preliminary efficacy of TAR-200 in patients with intermediate risk non–muscle-invasive bladder cancer: A phase 1 study.

505 Background: TAR-200 is a novel intravesical drug delivery system designed to provide a continuous, slow release of gemcitabine within the bladder. Prolonged gemcitabine exposure over days, instead of hours, such as with current standard intravesical installations, may achieve more efficient and effective tumor response. We report on the safety and tolerability of TAR-200 in patients with non-muscle–invasive bladder cancer (NMIBC). Methods: In this phase 1b, open-label, prospective study, patients with a papillary recurrence after prior histologically proven, intermediate risk (IR)-NMIBC received two 1-week TAR-200 dosing cycles over a 4- to 6-week period. The study used a marker lesion/ablation design. Cystoscopy was performed to assess for recurrent papillary disease and for complete transurethral resection of the residual bladder tumor. The primary outcome was safety of TAR-200. Secondary outcomes were tolerability, pharmacokinetics, preliminary efficacy, and immunohistochemistry. Results: In total, 12 patients received TAR-200 treatment. Insertion and removal of TAR-200 was uneventful. No TAR-200-related serious adverse events (AEs) occurred. Four patients had no TAR-200-associated AEs; the remainder had varying degrees of AEs (all grade ≤2 [CTCAEv4.0]), mainly consisting of low-grade urinary urgency, urinary frequency, and dysuria, with no delay in the treatment schedule. Two patients refused a second dosing cycle due to urinary urgency and frequency. Plasma gemcitabine concentrations remained below the lower limit of detection. Five of 12 patients (42%) had complete response (CR); of these, 4 had a pathologic CR and 1 had CR based on visual assessment (with no biopsy available for pathologic assessment). Conclusions: In this small, phase 1 series, TAR-200 appears to be safe and well tolerated in patients with IR-NMIBC. Clinical trial information: NCT02720367 .

The performance of double-layer rubber sealing ring under the action of low temperature environment

Aiming at the sealing failure of a water quality monitoring system in a low-temperature environment, a double rubber O-ring sealing structure was designed, and its sealing performance at low temperatures was studied. Finite element software ANSYS constructed the sealing structure, and the change of sealing performance of rubber O-ring in the process of standard temperature installation and low temperature was studied by a two-dimensional axisymmetric model. The results show that the equivalent strain and stress of the sealing structure show an increasing trend during the installation process. With the effect of the medium pressure, the maximum contact stress of the rubber seal ring increases from 2.6285 MPa at 20 ℃ to 2.6657 MPa at 0 ℃. The contact width decreases gradually with the decrease in temperature. With the initial compression rate increase, the maximum contact stress increases significantly. The simulation results show that the double-layer rubber O-ring structure still has good sealing performance at low temperatures.

СТАНДАРТИЗАЦИЯ ПЕРЕЧНЯ РИСКОВ И УСЛОВИЙ ПРИ СТРАХОВАНИИ СТРОИТЕЛЬНО-МОНТАЖНЫХ РАБОТ

The article is devoted to the problem of standardization of insurance contracts for construction and installation risks, which are currently proposed by the VSS. The article reveals the situation with the inclusion of costs in construction and installation works in the items of expenditure under state, municipal and maritime contracts. The problems of insurers related to sanctions pressure on the Russian insurance market, the closure of access for all domestic international insurers to reinsurance capacities and activities that can reduce the risks of cumulation of insurance events within one territory (Russian Federation) are described. The additional risks that need to be included for the development of insurance coverage under construction and installation works in standard construction and installation agreements, as well as new exceptions that were the result of the COVID-19 pandemic, are considered in detail. Separately, the risks and work with them during construction and installation work in the new Russian territories are described.

SBMLDiagrams: a python package to process and visualize SBML layout and render.

The systems biology markup language (SBML) is an extensible standard format for exchanging biochemical models. One of the extensions for SBML is the SBML Layout and Render package. This allows modelers to describe a biochemical model as a pathway diagram. However, up to now, there has been little support to help users easily add and retrieve such information from SBML. In this application note, we describe a new Python package called SBMLDiagrams. This package allows a user to add a layout and render information or retrieve it using a straightforward Python API. The package uses skia-python to support the rendering of the diagrams, allowing export to commons formats such as PNG or PDF. SBMLDiagrams is publicly available and licensed under the liberal MIT open-source license. The package is available for all major platforms. The source code has been deposited at GitHub (github.com/sys-bio/SBMLDiagrams). Users can install the package using the standard pip installation mechanism: pip install SBMLDiagrams. Supplementary data are available at Bioinformatics online.