Stages Of Process Research Articles

Studies of Phase Transformation Kinetics in the System of Nanocrystalline Iron/Ammonia/Hydrogen at the Temperature of 350 °C by Means of Magnetic Permeability In Situ Measurement

The kinetics of phase transformations in the nitriding process α-Fe → γ’-Fe4N → ε-Fe3-2N of the pre-reduced iron ammonia synthesis catalyst was investigated under in situ conditions (atmospheric pressure, 350 °C) by measuring changes of mass, gas phase composition, and magnetic permeability in a differential tubular reactor. The iron nanocrystallite size distribution according to their specific active surface areas was measured, and it was found that the catalyst is bimodal as the sum of two Gaussian distributions, also differing in the value of the relative magnetic permeability. Relative magnetic permeability of small α-Fe crystals in relation to large crystals is higher by 0.02. In the area of α → γ’ transformation, the magnetic permeability dependencies change, proving the existence of two mechanisms of the α-Fe structure change in the α-Fe → γ’-Fe4N transformation. In the first area, a solution of α-Fe (N) is formed with a continuous and insignificant change of the crystal lattice parameters of the iron lattice. In the second area, there is a step, oscillatory change in the parameters of the iron crystal lattice in FexN (x = 0.15, 0.20, 0.25 mol/mol). In the range of γ’-Fe4N → ε-Fe3-2N transformation, a solution is formed, with nitrogen concentration varying from 0.25–0.45 mol/mol. During the final stage of the nitriding process, at a constant value of the relative magnetic permeability, only the concentration of nitrogen in the solution εr increases. The rate of the phenomenon studied is limited by a diffusion rate through the top layer of atoms on the surface of iron nanocrystallite. The estimated value of the nitrogen diffusion coefficient varied exponentially with the degree of nitriding. In the area of the solution, the diffusion coefficient is approximately constant and amounts to 5 nm2/s. In the area of oscillatory changes, the average diffusion coefficient changes in the range of 3–11 nm2/s, and is inversely proportional to the nitrogen content degree. The advantage of the research method proposed in this paper is the possibility of simultaneously recording, under reaction conditions, changes in the values of several process parameters necessary to describe the process. The research results obtained in this way can be used to develop such fields of knowledge as heterogeneous catalysis, materials engineering, sensorics, etc.

Active Control of Properties of Fresh and Hardening Concrete

Concrete mixtures have an optimized mix design in view of attaining desired properties. However, after mixing, during further processing, it is typically not possible to further adjust the performance of the fresh and hardening concrete. A new and emerging approach is to actively control the concrete properties by means of responsive particles or polymers triggered by an externally applied signal. Active control of properties of concrete refers to the concept of on- demand changes of one or more properties of the concrete after mixing by triggering a response to one or more of the constituents using a specific trigger signal (e.g. thermal, chemical, electrical, magnetic...). The on-demand control of properties can focus on the processing stage (including e.g. pumping, casting, 3D printing), the curing and hardening stage (including e.g. control of capillary pressure, shrinkage, setting, and hardening) and even on the hardened stage during service life (e.g. active corrosion control, active crack healing...). Addressing specific obstacles in cementitious environments, ensuring responsive material stability, controlling signal applicability, cost, logistics, and on-site safety is crucial for successful implementation. A RILEM technical committee has been initiated in 2023, working on the concept of Active Control of Properties of Concrete (RILEM TC 317-ACP). The committee will focus on active control of properties of fresh and hardening concrete. This paper gives a short introduction to scope and activities of TC 317-ACP.

Impact of fruit reserve conditions from harvest to processing on the chemical composition and quality of coffee

Changes in the different stages of fruit processing are becoming a differentiating factor in coffee quality. Currently, generating delays in the processing of the fruit, that is, reserve, is a practice that can modify the sensory profile of the beverage. In this study, the fruit was reserved in three stages of maturity, two temperatures (15° and 20°C) and at two timepoints (24 and 48 h), establishing its chemical composition and sensory characteristics using analytical techniques such as liquid and gas chromatography. The state of maturity 1 showed an effect on malic and quinic acids due to the interaction of temperature and reserve time, while stage of maturity 3 showed an effect on glucose and fructose. The state of maturity 2 showed an effect of the reserve time on the same compounds of states 1 and 3, in addition to the content of defective beans and sucrose. The sensory quality expressed as the total SCA (Specialty Coffee Association) score and the attributes did not show treatments effect, the reserve of the fruit under the evaluated conditions presents an effect on the descriptors of the flavor. Extending the fruit reserve time from 24 to 48 h showed an increase in the groups of flavor descriptors associated with fruit and red fruits from 33.33 to 66.66% and from 34.04 to 65.95%. This implies that the constituent parts of the fruit such as the exocarp and mesocarp interact with the bean, leading to changes in the chemical composition and the improvement of the qualitative complexity of the sensory quality. This is a consequence of the increase in the frequency of the flavor descriptors of the fruit and red fruit category.

Effects of acute stress on biological motion perception.

Biological motion perception is an essential part of the cognitive process. Stress can affect the cognitive process. The present study explored the intrinsic ERP features of the effects of acute psychological stress on biological motion perception. The results contributed scientific evidence for the adaptive behavior changes under acute stress. After a mental arithmetic task was used to induce stress, the paradigm of point-light displays was used to evaluate biological motion perception. Longer reaction time and lower accuracy were found in the inverted walking condition than in the upright walking condition, which was called the "inversion effect". The P2 peak amplitude and the LPP mean amplitude were significantly higher in the local inverted perception than in the local upright walking condition. Compared to the control condition, the stress condition induced lower RT, shorter P1 peak latency of biological motion perception, lower P2 peak amplitude and LPP mean amplitude, and higher N330 peak amplitude. There was an "inversion effect" in biological motion perception. This effect was related to the structural characteristics of biological motion perception but unrelated to the state of acute psychological stress. Acute psychological stress accelerated the reaction time and enhanced attention control of biological motion perception. Attention resources were used earlier, and less attentional investment was made in the early stage of biological motion perception processing. In the late stage, a continuous weakening of inhibition was shown in the parieto-occipital area.

Electron-impact excitation data for W2+ in support of tungsten spectroscopy and re-deposition measurements for magnetically-confined plasmas

Abstract To better understand plasma wall interactions involving tungsten, accurate atomic structure and electron-impact driven collisional processes for near-neutral ion stages of tungsten are required. Complementing existing work on neutral and singly ionised tungsten, atomic structure and collisional calculations for W2+ electron-impact excitation have been completed. These excitation calculations are an important component of S/XB coefficients for near-neutral charge states, which may be used to spectroscopically infer re-deposition of tungsten at the plasma-solid boundary of fusion relevant devices. With W2+ in particular having emission lines that can be observed at ultraviolet (UV) wavelengths, while higher charge states of tungsten are unlikely to have lines possible to observe outside of the vacuum UV range. The atomic structure was generated using the General-purpose Relativistic Atomic Structure Package (GRASP0), implementing the Multi-configuration Dirac Fock approach (MCDF). This structure was the basis for a subsequent Dirac $R$-matrix electron-impact excitation calculation (DARC) to provide Maxwellian averaged rate coefficients. A synthetic spectrum was generated from this data using a collisional-radiative model to predict the strongest W~III spectral lines and these lines were compared to emission from the Compact Toroidal Hybrid (CTH) plasma device. Several of the strongest W~III lines are observed in CTH and agree well with the modelled line wavelengths and intensities, a table of these lines is provided that could be observed in other devices.

Cluster intercalation of aluminum tetrachloride in AlN cathode: Exploration and analysis of aluminum ion batteries.

When chloroaluminate (AlCl4-) serves as the electrolyte, aluminum nitride (AlN) has shown promise as a cathode material in aluminum ion batteries. However, there is currently a lack of research on the mechanisms of charge transfer and cluster intercalation between AlCl4 and AlN cathode materials. Herein, first-principles calculations are employed to investigate the intercalation mechanism of AlCl4 within the AlN cathode. By calculating the formation energies of stage-1-5 AlN-AlCl4 intercalation compounds with the insertion of individual AlCl4 cluster, we found that the structure of the stage-4 intercalation compounds exhibits the highest stability, suggesting that when the clusters begin to intercalate, it is important to start with the formation of the stage-4 intercalation compounds. In the subsequent phases of the charging process (stages 1 and 2), the stabilized structure with four inserted clusters demonstrates two characteristics: the coexistence of standing and lying clusters and the insertion of two standing clusters in an upside-down doubly stacked configuration, which further improve the spatial utilization while maintaining the structural stability. In addition, we infer that a phenomenon of coexisting intercalation compounds with mixed stages will occur in the course of the charging and discharging processes. More importantly, the diffusion barrier of AlCl4 in AlN-AlCl4 intercalation compounds decreases with the reduction of stage number, ensuring the rate performance of batteries. Therefore, we expect that our work will contribute to comprehend the intercalation mechanism of AlCl4 into the AlN cathode materials of aluminum ion batteries, providing guidance for related experimental work.

Artificial intelligence (AI) tools for academic research

Purpose The purpose of the paper is to explore the rapidly evolving landscape of artificial intelligence (AI) tools in academic research, highlighting their potential to transform various stages of the research process. AI tools are transforming academic research, offering numerous benefits and challenges. Design/methodology/approach Academic research is undergoing a significant transformation with the emergence of (AI) tools. These tools have the potential to revolutionize various aspects of research, from literature review to writing and proofreading. An overview of AI applications in literature review, data analysis, writing and proofreading, discussing their benefits and limitations is given. A comprehensive review of existing literature on AI applications in academic research was conducted, focusing on tools and platforms used in various stages of the research process. AI was used in some of the searches for AI applications in use. Findings The analysis reveals that AI tools can enhance research efficiency, accuracy and quality, but also raise important ethical and methodological considerations. AI tools have the potential to significantly enhance academic research, but their adoption requires careful consideration of methodological and ethical implications. The integration of AI tools also raises questions about authorship, accountability and the role of human researchers. The authors conclude by outlining future directions for AI integration in academic research and emphasizing the need for responsible adoption. Originality/value As AI continues to evolve, it is essential for researchers, institutions and policymakers to address the ethical and methodological implications of AI adoption, ensuring responsible integration and harnessing the full potential of AI tools to advance academic research. This is the contribution of the paper to knowledge.

Dementia-Friendly Hospital-The Perspective of Professional Dementia Experts.

To investigate the professional dementia experts' understanding of a dementia-friendly hospital to identify its characteristics. We used a qualitative design embedded in a case study. A total of 16 semi-structured expert interviews were conducted with 17 professional dementia experts. Using inductive content analysis, the interviews were analysed in a participatory manner involving a group of researchers and dementia experts. We identified six characteristics of dementia-friendly hospitals: Proud to be dementia-friendly-That's what we want; Seeing the human being-Taking care of everyone; Having everyone on board-It's a collective task; Being professional-It takes more than being nice and kind; Rethinking the 'running' system-We have to change, not them; and Being part of the community-Thinking beyond the hospital. The concept of a dementia-friendly hospital seems complex and requires a rethinking of the traditional hospital. For a conceptualisation, the involvement of people with dementia and their relatives is important to gain a comprehensive understanding. A dementia-friendly hospital is characterised by professional care that comprises a safe, familiar and supportive environment, is prepared but also flexible, has everyone on board, and sees the human being. To become dementia-friendly, individual interventions such as training courses can be a starting point. However, an overall concept is required that also includes components that contribute to successful implementation and a welcoming culture of people with dementia. Our findings on the perspective of professional dementia experts contribute to the conceptualisation of dementia-friendly hospitals. We reported our study according to the COREQ checklist. The investigation of the perspective of professional dementia experts is one part of a larger study. In this overall DEMfriendlyHospital study, we interviewed professional dementia experts, people with dementia and their relatives and also involved them in a participatory manner in various stages of the research process.

Progressive technologies of laser surfacing and gas‑thermal spraying

The article notes the experience of Yantai Huaheng Energy Conservation Technology Co., Ltd in applying protective anti‑corrosion polymer coatings and discusses the most promising modern recovery and strengthening technologies of thermal spraying (PAPS, AS, HVAF, HVOF) and laser cladding (LASC). Examples of installations that the company has and typical restored machine parts with protective wearand corrosion‑resistant coatings and the microstructure of coatings are given. The main stages of a typical technological process for applying coatings are noted. Using the example of the company, the feasibility and effectiveness of the development of this area in China is noted.

Mechanical Properties and Thermal Decomposition Mechanism of Glycidyl Azide Polyol Energetic Thermoplastic Elastomer Binder with RDX Composite

To improve the reinforcement effect between a binder and high solid filler in a propellant formula, grafting the bonding group into the binder to form a neutral polymeric is a practically novel approach to improving the interface properties of the propellant. In this work, a glycidyl azide polyol energetic thermoplastic elastomer binder with a –CN bonding group (GAP–ETPE) was synthesized, and the mechanical and thermal decomposition mechanism of GAP–ETPE with Hexogeon (RDX) model propellants were studied. The stress–strain results indicated that the tensile strength and strain of GAP–ETPE/RDX model propellants were 6.43 MPa and 32.1%, respectively. DMA data showed that the storage modulus (E’) of the GAP–ETPE/RDX model propellants could increase the glass transition temperature (Tg) values, those were shifted to higher temperature with the increase in filler RDX percentages. TG/DTG showed the four decomposition stages of the decomposition process of the GAP–ETPE/RDX model propellants, and the thermal decomposition equation was constructed. These efforts provide a novel method to improve GAP–ETPE/RDX propellants mechanical property, and the thermal decomposition behavior of GAP–ETPE/RDX propellants also provided technical support for the study of propellant combustion characteristics.

Bistable perception of symbolic numbers.

Numerals, that is, semantic expressions of numbers, enable us to have an exact representation of the amount of things. Visual processing of numerals plays an indispensable role in the recognition and interpretation of numbers. Here, we investigate how visual information from numerals is processed to achieve semantic understanding. We first found that partial occlusion of some digital numerals introduces bistable interpretations. Next, by using the visual adaptation method, we investigated the origin of this bistability in human participants. We showed that adaptation to digital and normal Arabic numerals, as well as homologous shapes, but not Chinese numerals, biases the interpretation of a partially occluded digital numeral. We suggest that this bistable interpretation is driven by intermediate shape processing stages of vision, that is, by features more complex than local visual orientations, but more basic than the abstract concepts of numerals.

Food waste management practices in restaurants: how to prevent and reduce food waste?

Restaurants produce significant food waste, which has major negative environmental, social, and economic impacts. Therefore, the prevention and reduction of food waste in restaurants needs to be planned, using appropriate management practices for the different stages of the process. The review will increase the understanding of food waste prevention and reduction, the stages of the management process, and the management practices involved. The results show that management practices are particularly related to menu planning, sourcing, preparation, serving, and customer service. In addition, the review identifies systematic management as an essential element in preventing food waste. However, achieving the objectives set will require raising the level of skills and integrating circular economy thinking into management practices. The suitability of management practices also depends on the geographical context, which is why more research on this topic is needed in Finnish restaurants.

Effective Engagement Techniques Across the Agricultural Conservation Practice Adoption Process.

Encouraging agricultural landowners to adopt conservation practices is crucial to enhancing ecosystem services in privately-owned farm landscapes. To improve engagement with landowners and increase adoption rates, much research has been dedicated to investigating how different psychological, social, economic, and political factors correlate with adoption. However, these studies largely measure adoption as a discrete, binary event. Doing so obscures sequences of landowner decisions and engagement techniques that conservation practitioners use to encourage landowners' progression through the adoption process. We report on two studies that contribute to the emerging literature on the agricultural conservation practice adoption process and the varying effectiveness of engagement techniques throughout. First, interviews with conservation practitioners in the Chesapeake Bay watershed, USA, yielded a preliminary model of the different stages in the adoption process and what techniques practitioners find effective at each stage. Second, an online experiment examined the effectiveness of a visualization intervention across two sequential outcomes in the adoption process, seeking further information and contacting a practitioner. Our results suggested that practitioners use a wide variety of engagement techniques, most of which are unique to a single stage in the adoption process, and that the effectiveness of the visualization technique varies substantially between different stages. Together these studies outline a suite of techniques that other practitioners may find effective at different stages of the adoption process, and suggest that research can better inform practice by accounting for variation in the effectiveness of different techniques across stages of adoption.

On determining of the protograph features based on the graphic-orthographic systems of manuscripts

This article is concerned with the study of medieval manuscripts and the determining of the features of protographs based on the graphic and orthographic systems of their scribal copies. The study involves three manuscripts created in Nuremberg in the 15th century. The texts of the mentioned manuscripts are copies from the first two complete translations of one of the medieval treatises. Based on the study of the graphic and orthographic systems of these texts, as well as some of their morphological features, the author of the article makes an attempt to establish the relationship between the texts under study, as well as to restore some of the features of their protographs. The sources of influence on the formation of the graphic and orthographic portrait of the scribe were identified as a result of the study of the graphic and orthographic features of the texts. Among them the author identifies the written tradition of the scriptorium, features of the local dialect and dialect areas, as well as characteristic features of the protograph. A separate group includes such a source of variability as the individual preferences of the scribe. Analysis of the graphic and orthographic portrait of each of the scribes who participated in the creation of the texts under study allows us to determine the approximate time and place of creation of the protograph, as well as changes characteristic of each stage of conscious processing of the text. As a result of the study, a diagram was drawn up that clearly demonstrates the relationships between the texts under study.

Exploring Attention Bias Mechanisms in Sub-Threshold Depression: ERP Insights into Biased Orientation and Disengagement

Individuals with depression may have alterations in attention that begin at the sub-threshold stage. This study explored attention bias from the perspectives of early attention orientation and late attention disengagement in individuals with sub-threshold depression (SD) and healthy control (HC) individuals using a cue-target paradigm and event-related potentials (ERPs). The study enrolled 46 participants, comprising 23 males and 23 females, with 25 individuals in the SD group and 21 in the HC group, exceeding the calculated sample size requirement. The data were analyzed from two aspects. Behavioral data showed that SD individuals had difficulty in attention disengagement and that the time of attention transfer was delayed. Analysis of ERP data revealed that, regardless of the attributes of the emotional stimulus, the cue information promoted participants’ response to the target stimulus. While SD individuals did show directional acceleration of attention to the emotional stimulus, no significant negative attention bias was observed. Taken together, these findings suggest that SD individuals do not show specific directional acceleration of attention to negative stimuli in the early stage of attention processing, although there may be attention avoidance.

At2-MMP is required for attenuation of cell proliferation during wound healing in incised Arabidopsis inflorescence stems.

Wound healing of partially incised Arabidopsis inflorescence stems constitutes cell proliferation that initiates mainly in pith tissues about three days after incision, and that the healing process completes in about seven days. Although the initiation mechanisms of cell proliferation have been well documented, the suppression mechanisms remain elusive. Matrix metalloproteinases (MMPs) are zinc-dependent endopeptidases well-known as proteolytic enzymes in animal systems functioning in extracellular matrix remodeling during physiological and pathological processes, including tissue differentiation, growth, defense, wound healing, and control of cancer growth. In this study, we report At2-MMP might contribute to the suppression mechanism of cell proliferation during tissue-repair process of incised inflorescence stems. At2-MMP transcript was gradually upregulated from day 0 to 5 after incision, and slightly decreased on day 7. Morphological analysis of incised stem of defected mutant at2-mmp revealed significantly enhanced cell proliferation around the incision site. Consistent with this, semi-quantitative analysis of dividing cells displayed a significant increment in the number of dividing cells in at2-mmp as compared to WT. These results showed that the upregulation of At2-MMP at the later stage of wound-healing process is likely to be involved in the completion of the process by attenuating the cell proliferation.

Using Duoethnography to Connect the Disability Justice Principles to Education Research about Disabled Populations on Campus

The terms disability inclusion, disability rights, and disability justice are often used somewhat interchangeably, but have distinct meanings within academe more broadly and academic research contexts. The purpose of this investigation was to explore these concepts in relation to our research and present the way in which we (as education researchers) grappled with what a critical, disability justice-informed research methodology involves. We used a qualitative, duoethnographic research approach as it is both a reflection of social justice and a method to advance it (Sawyer & Norris, 2013). We engaged in virtual, asynchronous and synchronous dialogues in writing and audio formats to reflect, critique, question, and eventually, generate new ideas and ways of moving forward. In the paper, we first consider how the Disability Justice Principles from Sins Invalid (2019) could be connected to our current research practices using two questions about ethical considerations as well as research methodologies and frameworks. We then theorize how education researchers can intentionally incorporate activism throughout each stage of the research process. A Disability Justice-informed education research framework is proposed for use with research about disabled populations in higher education. This framework addresses the relationship between stages of the research process, disability inclusion, and disability justice, which was the ongoing debate throughout our dialogues.

The Sanctions Principles-Based Regulation: A Blueprint for a New Approach for the EU Sanctions Policy (Part I)

192 Despite the tremendous number of studies devoted to the effectiveness of economic sanctions, the unprecedented number of sanctions applied and the recent European Union (EU) reforms on sanctions, sanctions effectiveness should be still a matter of debate. More than a year after Russia’s full-scale invasion of Ukraine, but G7-led sanctions have not materially hindered Russia’s war effort. This study intends to address this problem by focusing on how to make the use and application of EU sanctions against Russia more effective. In doing so, I argue that the main impediments to EU sanctions effectiveness are systemic in nature and inherent to the EU sanctions policy framework. The piecemeal changes of the EU sanctions regulatory framework undertaken so far have not solved these systemic flaws that undermine the effectiveness of EU sanctions. A fundamental revision of the entire system of the EU sanctions policy framework is needed. This study proposes implementing a comprehensive principles-based framework for EU sanctions policy, where harmonisation and the risk-based approach are its foundations, to make sanctions more effective. The proposed sanctions principles-based framework is broader in its scope than is currently the case; it covers a broader set of principles. The proposed frame includes all the stages of the sanctions process, is addressed to a broader number of actors and its foundations are developed. I recommend that this sanctions principles-based framework should be mandatory for use. This is the first part of a two-part article. Part I of the article discusses the need for the revision of the regulatory approach to the EU sanctions policy to increase the effectiveness of sanctions. It includes the analysis of the EU sanctions as a foreign policy instrument and a comprehensive overview of the EU regulatory framework on sanctions as well as the analysis of imposition of the EU sanctions against Russia. Part I also discusses policy proposals for the effectiveness of the EU sanctions, such as harmonisation of the EU sanction policy and the application of a sanctions risk-based approach.

Effectiveness of moisturising therapy in treating nipple trauma: a systematic review protocol

IntroductionBreastfeeding is crucial in infant nutrition and bonding, recommended for at least 6 months and up to 2 years postpartum, providing health benefits for both infants and mothers. However, nipple...

Validation of the Scoliosis Japanese Questionnaire-27 in Korean patients with adolescent idiopathic scoliosis

We sought to evaluate the reliability and validity of the Korean adaptation of the Scoliosis Japanese Questionnaire-27 (SJ-27). This involved translating the English SJ-27 into Korean and back-translating it, followed by completing all stages of the cross-cultural adaptation process. Subsequently, the Korean SJ-27, along with the validated Scoliosis Research Society-22 (SRS-22) questionnaire, was administered to 140 consecutive idiopathic scoliosis patients wearing a brace. Reliability was determined using kappa statistics to assess agreement for each item, the intraclass correlation coefficient (ICC), and Cronbach’s α. Construct validity was established by comparing responses on the SJ-27 with those on the SRS-22 using Pearson’s correlation coefficient. All items showed kappa statistics indicating agreement above 0.6. The SJ-27 demonstrated excellent test–retest reliability (ICC=0.91). Internal consistency measured by Cronbach’s α was very good (α = 0.898). The Korean version of the SJ-27 exhibited significant correlations with both the total score and individual domain scores of the SRS-22. The adapted Korean SJ-27 was effectively translated and showed acceptable measurement properties, making it suitable for assessing outcomes in Korean-speaking patients with idiopathic scoliosis.