Squirrel Cage Induction Generator Research Articles

Analysis of magnetic saturation effects in the squirrel cage induction generators

This work concerns an investigation on the analysis of the magnetic saturation effects in the three-phase squirrel cage induction generator which is considered as a main device in wind energy conversion systems. The magnetic saturation is considered as an important factor causing destructive effects on power qualities such as harmonics and distortion. Several approaches have been presented in the literature for the modeling of the electric machines considering magnetic saturation. The widely used and precise approach is the finite elements method which is particularly characterized by its high computational time. The novelty in this paper is that a state model has been developed for the healthy conditions of the three-phase squirrel cage induction generators considering the experimental variation of the magnetizing inductance in terms of the magnetizing current. Simulation and experimental tests are provided to extract some important signatures on stator voltages and currents. It will be deduced that the spectrum analysis of stator currents contains useful information on magnetic saturation. Experimental and theoretical results illustrate the consistency of this approach for the modeling and analysis of the squirrel cage induction generators considering the magnetic saturation.

Three-phase model of SCIG-based variable speed wind turbine for unbalanced DSLF analysis

Steady state performances of the electric power distribution system are normally assessed or evaluated based on load flow analysis. To properly carry out the analysis, a valid steady state load flow model of each distribution system component, including the wind power plant (WPP), needs to be developed. The present paper proposes a method for modeling and integrating squirrel cage induction generator (SCIG)-based variable speed WPP into a three-phase unbalanced distribution system load flow (DSLF) analysis. The proposed method is based on a single-phase T-circuit model of fixed speed WPP, which has successfully been applied to balanced electric power systems. In the present work, the single-phase T-circuit model is extended and modified to be used in steady state load flow analysis of three-phase unbalanced distribution systems embedded with SCIG-based variable speed WPP. Results of the case studies confirm the validity of the proposed method.

FRT capability improvement of a wind power system using support vector regression and deep neural network models

ABSTRACT The increasing energy demand and environmental conditions have led many countries to favor renewable energy,such as wind and solar,over conventional power plants. As per the Central Electricity Authority (CEA), India’s wind power capacity has grown substantially, reaching 45,154 MW in 2023, from 22,465 MW in 2013. However, integrating wind generators to an existing power system network can reduce transient stability during faults. To prevent wind turbine disconnection during faults, Indian grid code authorities mandate Fault Ride Through (FRT) or Low Voltage Ride Through (LVRT) capability for wind turbines. This paper proposes Dynamic Voltage Restorer (DVR) for enhancing the FRT capability of a constant speed wind turbine. Analysis and simulation are done on a fixed speed wind turbine employing Squirrel Cage Induction Generator (SCIG) under balanced and unbalanced voltage sags. Performance of DVR with two Artificial Intelligence-based controllers, Support Vector Machines(SVM) Regression Model Based Supervised Machine Learning algorithm, and Deep Neural Network (DNN) controller, is analysed and compared. The SVM Regression algorithm, achieves 100% voltage sag compensation under unbalanced voltage sags, reduces torque pulsations to 25% and maintains rotor speed at rated values, enabling the turbine to remain connected to the grid. Additionally it reduces Total Harmonic Distortion to 2%.

Investigation of the Impact of SSSC-Based FLC on the Stability of Power Systems Connected to Wind Farms

The integration of renewable energy sources into power systems has increased significantly in recent years. Among various types of renewable energy, the use of wind energy is growing rapidly due to its low operating cost, wide distribution worldwide, and no greenhouse gas emissions. However, power systems integrated with wind energy may face stability and reliability issues due to the intermittent nature of wind power. Therefore, in power systems connected to wind farms, it is usually required to use some compensators such as static synchronous series compensator (SSSC) to increase the system performance under abnormal conditions. On the other hand, for an SSSC to be effective in improving the system performance, it must be equipped with a suitable controller. In this paper, a fuzzy logic controller (FLC) is used for the SSSC because of its advantages over conventional controllers. Extensive research has been conducted in power systems with wind turbines in which SSSC or FLC has been used; however, their simultaneous application in such systems has received less attention. Therefore, this article aims to fill this gap. The proposed method is implemented on two power systems and the simulation results are analyzed. In both systems, the dynamic behavior of three different wind farms is examined. In the first and second wind farms, either a squirrel cage induction generator (SCIG) or doubly-fed induction generator (DFIG) are used, whereas in the third one which is a combined wind farm (CWF), an equal number of SCIG and DFIG are employed. In wind farms with SCIG or DFIG, an SSSC is also utilized. Furthermore, an FLC is employed for the SSSC to improve its efficacy. A proportional integral (PI) controller is also considered for the SSSC, and its results are compared with FLC results. The simulation results confirm the superiority of FLC over PI controller.

Robust predictive control strategy of SCIG-based drive system

This article presents a robust finite control set predictive scheme for a stand-alone squirrel cage induction generator (SCIG) drive. This technique is considered an alternative to the drive system due to the inclusion of system nonlinearities and fast dynamic response. The control objective in the distributed generation environment is to fix the output voltage to follow the stand-alone requirement. The strategy establishes optimized switching instants for cost function minimization for both source and load converter control and diminished cross-coupling amid active and reactive power during transient scenarios. The scheme is designed to achieve the minimal effect caused by the parameter uncertainties. During source and load changes, this work will also address the maintenance of dc-link voltage, machine, and load variables at the set value, supported by machine and load-end converter control to achieve stand-alone load objectives. In addition, the presented scheme is also tested with random variation of speed to check the efficacy of the control configuration. The drive performance is evaluated by simulation using MATLAB/Simulink environment. Comprehensive real-time findings obtained from a scaled laboratory test bench using dSPACE-1104 are provided to verify the feasibility of the predictive solution.

A Modified Reduced-Order Generalized Integrator–Frequency-Locked Loop-Based Sensorless Vector Control Scheme Including the Maximum Power Point Tracking Algorithm for Grid-Connected Squirrel-Cage Induction Generator Wind Turbine Systems

A Modified Reduced-Order Generalized Integrator–Frequency-Locked Loop-Based Sensorless Vector Control Scheme Including the Maximum Power Point Tracking Algorithm for Grid-Connected Squirrel-Cage Induction Generator Wind Turbine Systems

Future Scope and Current Energy Situation of Wind Energy, with a Simulation of Small Wind Farm in Matrix Laboratory (MATLAB)

When the world is going through extreme energy shortage, mainly the non-renewable energies, wind energy is the hope along with solar energy, hydro energy, nuclear energy and bio mass energy to meet the energy demand. In the end of 2021, in India only, the wind capacity was 40 GWatt [8]. By the end of 2030, new 30 GWatt offshore wind capacity will be installed [8]. Wind turbines may be of various shapes and sizes. When more than one wind turbines are working together to create electrical power, they form a wind farm. The aim of this particular project is to make a simulation of a small wind farm of 4.5 MW in the simulation part of MATLAB software. Here squirrel cage induction generators are used as the electrical generators connected to the turbines. It generates power for the grid. SVC is connected to the wind turbines to control the overall reactive power. The aim is to make a MATLAB Simulink phasor model of a 4.5 MW wind farm with SVC with three fully functioning wind turbines.

Field-Oriented Control of a Nine-Phase Cage Induction Generator with Large Speed Changes and Variable Load

This paper presents a voltage control system for multiphase squirrel-cage induction generators operating at a high variability of speed and variable load. Field-oriented vector control was used with a change in the sequence of the stator phase currents what changes the number of poles of the magnetic field produced by nine-phase stator winding. At low speeds, the current sequence is changed so that the number of poles increases allowing for the desired voltage to be obtained with greater efficiency. The task of the automatic control system was to control the DC voltage to a desired value at the output of the multiphase PWM converter. This is an alternative control method to the scalar control of voltage and frequency presented in a previous work. The control method and parameters of the automatic control system result from the mathematical model of the multiphase induction machine. The results of the laboratory tests were compared with the effects of the operation of the same nine-phase scalar controlled generator.

A new-fangled connection of UPQC tailored power device from wind farm to weak-grid

A significant portion of wind power conversion systems worldwide comprise wind farms (WFs) that use Squirrel Cage Induction Generator (SCIG) and are directly linked to the power grid. In facilities that generate electrical energy at a moderate level, WFs are connected by means of distribution systems that use medium voltage (MV). It is not uncommon for such a system to produce a scenario in which the amount of electricity generated corresponds to the grid’s transit volume. When a wind farm’s wind power generation system is connected to a weak grid, the lack of potential control of the Point of Common Coupling (PCC) is a primary issue. This strategy is called a “Wind Farm with Weak Grid Connection.” Therefore, the amalgamation of weak grids, fluctuating electricity from wind, and variations in load on the system cause disruptions in the PCC voltage, further degrading the Power Quality (PQ) and the WF stability. Either the control method at the production level or the compensating strategies at the PCC level can improve this situation. If wind farms are built on SCIG and are directly linked to the grid, it is essential to utilise the last substitute. The technology known as Custom Power Devices (CUPS), proved extremely helpful for this type of application. This study presents a compensation technique based on a specific CUPS device, known as the Unified Power Quality Compensator (UPQC), as a possible solution. The potential terminals of WF needed to be regulated, and the voltage fluctuations on the grid side required to be reduced, so a custom-made control strategy for the UPQC device was designed internally. The control of power, such as active and reactive in the UPQC’s series and shunt converters, as well as the transmission of power via the UPQC DC-Link between converters, are the foundation of the internal control strategy that has been developed. Compared to other bespoke tactics that use reactive power, this strategy increases the UPQC’s capability to provide compensation. The suggested study calculates THD using a FUZZY controller. The results are compared to PI controller results. Simulation findings show how the suggested compensating strategy can minimise THD values and improve wind farm power and stability. The simulations suggest that the proposed compensating strategy enhances WF power and stability.

Constant Voltage Model of SCIG-Based Variable Speed Wind Power Plant for Load Flow Analysis

In recent years, the application of variable-speed wind power plants (WPPs) has become more and more popular and surpassed fixed-speed WPPs. This popularity is mainly because variable-speed WPPs are much more efficient in capturing or extracting wind energy than fixed-speed WPPs. Due to its relatively cheaper cost, the use of SCIG (Squirrel Cage Induction Generator)-based variable-speed WPP is currently increasing. This type of WPP is usually equipped with a power electronics converter to obtain a broader range of variable-speed operations. Modeling the power system components is undoubtedly necessary for performing the system analysis (including load flow analysis). This paper discusses the steady-state model of SCIG-based variable-speed WPP for load flow analysis of electric power distribution systems. The proposed model can be used for SCIG-based variable-speed WPP with voltage control operating mode. The model was developed based on formulas that calculate the turbine mechanical power input and the WPP electrical power output. This paper also presents a case study in which the proposed model is applied to a representative electric power distribution system.

LCL Filter Design of STATCOM using Genetic Algorithm Scheme for SCIG Based Microgrid Operation

In a microgrid static Compensator (STATCOM) is the most prominent inverter circuit for stabilizing the bidirectional power flow requirements of the system. This inverter circuit is the primary source of harmonics when the supply current feeds from the microgrid to the main grid. Improved control strategy and proper filter design may give solution to these issues and so, there is a huge scope of research in the field of the converter control techniques and filter designing for such microgrid based power system. The key objectives of this paper are (i) to develop an adequate current control scheme for adjusting real and reactive power fluctuations produced by load time to time, and (ii) to reduce the harmonic level of output characteristics in terms of real and reactive power flow and current frequency. For this, an approach is presented to estimate the filter design parameters for current controlled STATCOM connected to squirrel cage induction generator (SCIG) based microgrid. A nature-inspired optimization namely, genetic algorithm (GA), is implemented to estimate the most suitable parameters for the LCL filter. Results obtained through GA are validated with a conventional mathematical method in terms of real and reactive power flow through microgrid along with harmonic-based studies.

Performing Wind System with Rectifier with Near Sinusoidal Input Current

The RNSIC-1 (rectifier with near sinusoidal input currents converter), is the foundation of a wind generator system that is presented. The three inductances that make up a traditional RNSIC–1 converter are eliminated in the proposed arrangement, and the SCIG generator's leakage inductances fill their place. This is what makes it new. The wind system's role in the load currents is discussed. Lower power losses, smaller harmonic input currents, fewer EMI issues, excellent dependability, and cheaper costs are characteristics of the new wind system. This new wind system could be used for partial variable speed wind turbines (usually 70% to 100% synchronous speed) and lower hydro connector squirrel cage induction generators (SCIG).

Analysis and design of wind energy system based on nonlinear speed controller

This paper presents a control fuzzy robuste strategy for a squirrel cage Induction generator (SCIG)-based wind energy conversion system. Control strategies is presented along with the mathematical modeling of the employed configuration. The maximum power point extraction of the wind turbine is addressed along with the proposed strategy. The approach method is introduced to control the generator speed and regulate the flux. The wind system is then simulated in Matlab-Simulink and the developed model is used to illustrate the behavior of the system. The simulation results are presented and discussed at the end of this paper.

An intelligent wind turbine with yaw mechanism using machine learning to reduce high-cost sensors quantity

In this paper, with the assistance of some tools and a machine learning model, a smart wind turbine was formed that eliminates some expensive sensors and reduces sensor complexity. Squirrel cage induction generator (SCIG) and six rotor blades make up the proposed design, and depending on the wind's direction, the turbine itself can rotate the rotor hub to produce energy more effectively. Additionally, two stepper motors are coupled to the yaw mechanism with the aid of the rotor hub, and the entire controlling procedure will depend on the direction of the wind. The rotor hub must continuously revolve in the same direction as the wind to maximize wind energy utilization. Additionally, to correctly predict wind degrees, a machine learning model was deployed. Random forest regression was used to train and predict the wind direction. The model is deployed in Raspberry Pi, where the incoming sensor values are being stored. Using the generated data, machine learning model was trained and it can be concluded that the model can potentially replace some of the expensive sensors to reduce cost. The model can be used for similar weather conditions only based on machine learning model and fewer sensors.

An adaptive control strategy for grid-forming of SCIG-based wind energy conversion systems

One of the crucial issues in the expansion of isolated wind energy conversion systems (WECSs) is the design of a grid forming control structure that is robust to changes of the system’s operating point in the steady-state as well as transient conditions. This paper has addressed the voltage/frequency control of a local microgrid as well as flux and slip control of a squirrel cage induction generator that feeds the microgrid via a back-to-back converter in an isolated WECS. An adaptive nonlinear voltage control structure has been proposed for load side converter (LSC) consists of a constant frequency voltage regulator and a current controller based on the Lyapunov function method (LFM), which are connected in cascade. In an outer loop, the reference current of LSC is generated by the voltage regulator designated for maintaining the voltage/frequency of the microgrid. In an inner loop, the reference signals are robustly tracked by the current controller. In a novel reference frame that its angle difference with the stationary reference frame is determined by a dual loop DC link voltage controller, an LFM-based nonlinear flux controller is proposed for the machine side converter (MSC). Using the proposed flux control structure, in addition to maintaining the flux magnitude at a nominal value, by controlling the generator slip through adjusting the speed of the proposed reference frame, the power balance is established and the DC voltage is maintained at a pre-set value. The performance of the proposed controllers has been investigated through simulation in the MATLAB® software. The obtained results confirm the robustness and stability of the proposed control structure with respect to various disturbances and uncertainties.

Dynamic analysis of grid-connected hybrid wind farm

Since the last couple of years, the expansion of grid-connected wind farms (WFs) has increased dramatically. The wind turbine might be a fixed-speed squirrel cage induction generator (FSWT-SCIG) or a variable speed wind turbine with a doubly-fed induction generator (VSWT-DFIG). The main disadvantage of FSWT-SCIG is its lack of ability to adjust power quality. Inversely, the VSWT-DFIG is a competitive wind turbine technology that allows for the effective management of both active and reactive power outputs. Moreover, it has some extraordinary functionaries rather than FSWTSCIG. However, the major downside to this system is that it only has a partial rating AC/DC/AC power converter, which is extremely expensive. Hence, to reduce the overall cost combining the implementation of VSWT-DFIG and FSWT-SCIG in a WF could be a feasible alternative. Therefore, a novel DFIG control technique is proposed in this article, which can keep the connection point voltage of the hybrid WF stable during dynamic analysis. To evaluate the proposed controller responses PSCAD/EMTDC software has been used.

TCSC Application for Transient Stabilization of Wind Turbine with Fixed Speed Induction Generator

Wind turbines (WTs) are a desirable alternative to traditional nonrenewable power resources as a result of recent environmental concerns. Some of them are fixed speed wind generator (FSWG) and have been integrated to power system by squirrel cage induction generator (SCIG). Induction machine absorbs reactive power during all operating conditions, especially at fault condition may result in severe voltage drop which can lead to generator outage. This outage disconnects a significant amount of active power and consequently leads to frequency instability. In order to prevent induction generator (IG) outages in short circuit failures, this paper investigates thyristor-controlled series capacitor (TCSC) device as a candidate solution. TCSC compensates the IG terminal voltage drop by adjusting transmission line impedance at fault condition. In the proposed method, a metaheuristic technique means that shuffled frog leaping algorithm (SFLA) has been utilized to optimize the TCSC controller gains. The proposed scheme can be applied for both SCIGs and wound rotor induction generators (WRIGs) which is another advantage of this method. Single-machine infinite bus system is considered as case study, and various operating conditions and disturbances have been considered to verify the effectiveness of the proposed method.

Comparative Study of Grid Frequency Stability Using Flywheel-Based Variable-Speed Drive and Energy Capacitor System

Recently, there has been a rise in the integration of renewable energy sources into power grids. As a result of this, there is a need to carry out new studies in order to understand the dynamics of power grids during disturbances that is mainly caused by the stochastic nature of wind energy. The operation of modern power grids that are tied to wind farms follows a stipulated grid requirement or grid codes, considering the allowable threshold frequency variation during grid dynamics. This paper presents a comparative study of two frequency control schemes considering grid frequency stability using two frequency control topologies. A novel dynamic flywheel scheme with a doubly fed induction generator (DFIG) variable-speed wind turbine with the coordinated control of excess kinetic energy and mechanical torque during operation was the first scheme, and a control strategy of an energy capacitor system (ECS) with a squirrel cage induction generator fixed-speed wind turbine (FSWT) was the second scheme. The salient part of this study was that the DFIG maximum point power tracking for effective smoothing of the output of the wind generator in the first scheme was designed based on the control strategy of its reference power to achieve smoothing of the wind power at the terminals of the wind generator. The model system employed in this work was a wind farm that is tied to a conventional power grid made of steam and hydro synchronous turbines. For an effective and fair comparison of results, the same natural wind speed was used in PSCAD/EMTDC for both schemes. When no control, Scheme 1, and Scheme 2 were implemented, the frequency dips were 47.20, 49.99, and 49.99 Hz with overshoots of 50.500, 50.005, and 50.001 Hz and recovery times of over 600.00, 0.01, 0.01 s, respectively, for the frequency variable.

Improvement of power system stability in wind connected generator by using PSAT

Voltage stability in power systems is a major problem that receives international attention. An open and free source piece of software, Power System Analysis Toolbox (PSAT) is used in this study to create a model of modified IEEE 14 bus system. Models of two recently created wind turbines—the Squirrel Cage Induction Generator (SCIG) and Doubly Fed Induction Generator (DFIG)—are connected to a modified IEEE 14 bus system. The stability of the power system is examined in this work in relation to the effects of Squirrel Cage Induction Generator (SCIG) and Doubly Fed Induction Generators (DFIG). Here, both DFIG and SCIG, which have variable speeds, are regarded as wind generators. In this work, a small signal stability investigation using SCIG and DFIG wind turbine systems was carried out on a modified IEEE 14 bus system. The results of their simulation were analysed.

Impact of DC link brake chopper design on the LVRT behavior of full-scale converter wind turbines

Wind turbines (WTs) are loaded by the wind and by the electrical grid. A low voltage ride through (LVRT) is a special load case for WTs, which can be critical for their drivetrain. They are usually less severe for WTs with a full-scale converter (FSC); however, in some cases there are still loads observable in the mechanical drivetrains of WTs with FSCs. Different aspects like the brake chopper design, the control and specifications of the grid side converter (GSC) as well as the grid and fault parameters affect these loads. In this paper, three different LVRT behaviors of a WT with a squirrel-cage induction generator (SCIG) and a FSC were investigated via simulations. In the worst case, a sharp peak in the electromagnetic torque of the generator after fault clearance is possible. The cause lies in the GSC control, especially the phase-locked loop (PLL), and can also be influenced by adjusting the control parameters, brake chopper and filter design. The resulting mechanical drivetrain torque, on the other hand, is increased by only 2.9% for a very short time. Thus, the loading of the mechanical drivetrain components is only slightly increased. Therefore, the risk of damage to the mechanical components of the FSC WT due to grid faults is relatively low.