Spin Speed Research Articles

HRMAS NMR for Studying Solvent-Induced Mobility of Polymer Chains and Metallocene Migration Into Low-Density Polyethylene (LDPE).

HRMAS (high-resolution magic angle spinning) nuclear magnetic resonance (NMR) spectroscopy of low-density polyethylene (LDPE) affords 1H and 13C NMR spectra with superior resolution. For acquiring HRMAS NMR spectra, the polymer is first swollen with representative organic solvents. Then, the samples are measured with a conventional solid-state NMR spectrometer in the wideline mode or at the low spinning speed of 2 kHz. Anisotropic interactions like CSA (chemical shift anisotropy) and dipolar interactions are reduced due to the additional mobility of the polymer chains in the presence of the solvent within the polymer network. The combined effect of this mobility and MAS leads to signals with substantially reduced halfwidths as compared to classic MAS of the dry polymer. With HRMAS, all signals of the polymer become visible, and the spectra can be used for a quick and easy assessment of the polymer swelling behavior in diverse solvents. Being able to characterize polymers on the molecular level, and identifying the solvents that penetrate the polymer network best, enables the study of post-synthesis modifications of the polymers. It is demonstrated by paramagnetic HRMAS that the metallocene nickelocene (Cp2Ni) penetrates the LDPE network along with the solvent and is homogeneously dispersed in the polymer. SEM images prove that the structure of the polymer is not altered by the presence of a solvent and Cp2Ni. The impact of the paramagnetic Cp2Ni on the 1H signal halfwidth and T1 time of LDPE is studied. HRMAS allows a quick assessment of metal complexes regarding their ability to penetrate the LDPE network and therefore supports future studies of catalytic polymer degradation.

Research on the difference of stroke characteristics and stroke effect between different stroke duration of table tennis players

This study aimed to explore the differences in joint kinematic characteristics and stroke effect between fast and slow strokes of table tennis players. Thirty-four table tennis players were randomly selected as participants for this experiment. A high-speed infrared motion capture system was used to collect kinematic data of the right-side upper and lower limb joints during strokes. Simultaneously, a high-speed camera was used to measure the stroke effect. According to the duration of a stroke, the stroke data were classified into two types: fast-stroke and slow-stroke using a two-step clustering algorithm. The duration of the three phases of fast-stroke was shorter, with faster ball speed and stronger spin. Compared with slow-stroke, fast-stroke exhibited shorter displacements in the three lower limb joints and faster linear velocities in the three upper limb joints. In addition, the motion angles of the knee and ankle joints were smaller, while the angles of the hip, shoulder, and elbow joints were larger, with higher angular velocities. Increasing the extension speed of the lower limbs, the flexion speed of the elbow joints, and the wrist movement speed can achieve fast strokes, enhancing ball speed and spin. Small and quick hip joint movement can effectively transfer energy to the upper limbs, increasing the movement speed of the elbow and wrist joints, thus improving the ball speed and spin of the stroke.

Higher-order nonlinear modeling and multi-modal performance of axially restrained diverse flexible shaft-disk assemblies

Flexible shaft-disk combinations are essential in engines, turbines, and machinery. Understanding their modal characteristics is vital for industry-wide performance, reliability, and safety. This study uses higher-order modeling and multi-modal analysis to grasp complex dynamics, especially with multiple disks of varied sizes. Employing Hamilton’s method and Galerkin’s technique, equations of motion are formulated and then utilized for multi-modal analysis considering structural nonlinearity. Various shaft-disk arrangements are analyzed, including disk number, size, position, and shaft material, to understand their impact on modal behavior. The findings reveal the substantial impact of disk count, sizes, and placements on modal dynamics and intricate vibration characteristics across diverse spinning speeds. This effect is accentuated by integrating higher-order modeling into multi-modal analysis. Notably, higher-order deformation enhances overall resilience capacity and imposes more effective vibration restrictions than the linear approach. Furthermore, the investigation explores how different shaft materials influence modal characteristics, critical speeds, and vibration amplitudes in various shaft-disk combinations. Theoretical findings are validated using numerical results from 3D finite element-based models simulated with ANSYS 3D for accuracy. Ultimately, the study introduces a theoretical framework adaptable to numerous flexible shaft-disk combinations, offering a valuable resource for understanding and enhancing system behavior, benefiting engineers and researchers alike.

Effect of spin coating speeds on electrical and optical characteristic of perovskite SrTiO3 thin films prepared by sol-gel method

The perovskite strontium titanate (SrTiO3/STO) was prepared by the sol-gel process, and the STO thin film was deposited onto a glass substrate by the spin coating method. Effect of different spin coating speeds on the thickness, structural, optical, and electrical properties of the STO thin films was discussed. Five STO films with various spin coating parameters of 2000, 4000, 6000, 8000, and 10000 RPM were prepared. Thickness profilometer tests have shown that the thickness of the STO film changes from 802 nm at 10000 RPM to 1321 nm at 2000 RPM spin coating speed. The prepared STO films morphology was examined by scanning electron microscope. X-ray diffraction measurements have shown that crystalline STO films have been produced with a cubic perovskite structure. The optical properties of the prepared STO films were investigated using an ultraviolet visible spectrophotometer, and the results indicated that the STO film at 8000 and 4000 RPM spin speed show the lowest and the maximum optical band gap (2.83 and 2.90 eV, respectively). All STO films have absorption coefficient values higher than 103 cm−1. The prepared STO thin films had a refractive index between 2.40 and 2.42. The electrical characteristics of the prepared STO films were investigated using the four-point probe method, and it was found that as the spin coating speed increased from 2000 to 8000 RPM, the resistivity of the STO films reduced from 6.629∗1010 to 3.009∗1010 Ω. Moreover, the STO film at 8000 RPM spin speed has the best electrical conductivity (3.301∗10−5 S m−1).

Fabrication with magnetic-spin coating: Influence of magnetic-inertia energy ratio on gold-pickering ferrofluid droplet assembly morphology

Magnetic self-assembly of nanoparticles is a well-known technique for creating thin-film array-patterned functional microstructures. However, an uncontrollable hierarchical assembly formation of magnetically stimulated particles has hindered the desired formation of free-standing two-dimensional (2D) array patterns in thin-film layers. In this study, we proposed a fluidic shearing effect from spin coating to reduce magnetically stimulated particles’ disarrayed and complex chain formations, thus promoting linear array formations, even as the film becomes thinner. A series of tests were conducted on a gold-Pickering ferrofluid emulsion (GPFE) dispersed in 15.2 mPas aqueous polyvinyl alcohol (PVAh), which was subjected to varying spin speeds under magnetic setups such as single (SI), compound (CC), and concentric (CR). These setups were chosen to observe the influence of magnetic field strength and distribution on the generated pattern profile from microscopic binary images of the resulting thin films. The aim was to quantify the formed chain thickness (ChT), chain gaps (ChG), and chain lengths (ChL) to capture the morphology and geometrical features of the formed patterns. Our results showed that the quantified values of these profiles and their dimensionless relationships were significantly influenced by the ratio between the applied magnetic packing energy and the centrifugally controlled fluidic energy, QPD. This investigation showed that ChT/ChG for a corresponding QPD value is 98.6% the same for all configurations, and CR was the best setup going forward, as it yielded the lowest array quality defectivity of 14%. Therefore, we assert that this fabrication method offers flexibility, cost-effectiveness, and expandability in generating linear array patterns that contain graduating variability in grating order dimensions within a single cast that can serve efficiently as a substrate for biomolecules under enhanced Raman and Infrared spectroscopies.

The difference of dynamic elasticity characteristics and stroke effect between two types of new material seamed plastic table tennis ball

The diameter and weight of different brands of table tennis ball will affect the ball’s elasticity and stroke. The purpose of this study is to analyze the difference of the dynamic elasticity and stroke effect between the two brands of new plastic ball. A self-made experiment was designed to test the dynamic elasticity characteristics of DHS D40 + and Nittaku 40+. Table tennis players (N = 18) were randomly selected from the China Table Tennis College (Mage = 15.16 ± 2.41; Mheight = 1.59 ± 0.32 m; Mweight = 45.72 ± 5.17 kg). Each participant was righthand shake-hands grip. A speedometer was used to record the ball speed and a high-speed camera was used to measure the spin speed. Data normality was verified by using the Kolmogorov-Smirnov test. The independent t-test was conducted to assess the differences of the dynamic elasticity and stroke effect between the two types of plastic ball. Results showed that the rebound speed and decrement rate of DHS D40 + and Nittaku 40 + both increased with the increased falling speed, respectively. When falling at high speed, there was a significant difference of dynamic elasticity between DHS D40 + and Nittaku 40+ (p < 0.01). There was also a significant difference in the ball speed and spin speed between the two types of new material seamed plastic ball during the backhand backspin stroke (p = 0.041, p = 0.022, respectively), and the ball speed and spin speed of DHS D40 + were higher than that of Nittaku 40 + ball. Compared with the DHS D40+, the Nittaku 40 + has a faster rebound speed, higher rebound height, and better dynamic elasticity. Therefore, under same striking conditions, when hitting the Nittaku 40 + ball, players need to increase the swing distance and hit the ball with more strength to improve the ball speed and rotation speed; increase the spin and decrease the ball’s rebound height of the serve.

Design of experiments with the support of machine learning for process parameter optimization of all‐small‐molecule organic solar cells

AbstractTraditionally, squaraine dyes have been studied and employed in biomedical research due to their excellent optical properties, and the molecules are being adopted in different research fields such as organic solar cells. In this study, we investigate correlations between solar cell performance and processing parameters of all‐small‐molecule bulk heterojunction solar cells comprising squaraine (SQ) as electron donor (D) and non‐fullerene small molecules (e.g., ITIC) as electron acceptor (A) with the help of machine learning (ML) and design of experiment (DoE) methods. Among the five predictive ML models tested with the selected parameters, the eXtreme gradient boosting model shows the satisfactory results with quite high coefficient of determination of 0.999 and 0.997 in training and testing sets, respectively. By measuring the contribution of each input variable to solar cell efficiency, four process parameters, that is, the total concentration, the ratio of D/A, the rotational speed of spin coating, and the annealing temperature, are found to be the key features strongly correlated to solar cell efficiency. From contour plots in DoE, the highest solar cell efficiency of approximately 5% can be predicted under the conditions of 15 mg mL−1 in solution concentration, a 1:2 mix ratio of D and A, rotational speeds ranging from 800 to 900 rpm, and annealing temperatures within 100–110°C. Using the suggested parameter conditions, we fabricated solar cells, achieving a quite high efficiency of approximately 4%. Besides the global optimization conditions, we also employ the solvent vapor annealing combination to the thermal annealing to facilitate further mobilization of molecules and more optimized microstructure of bulk heterojunction films, resulting in a further enhancement in solar cell efficiency of more than 20%.

Enhancing Long-Term Memory in Carbon-Nanotube-Based Optoelectronic Synaptic Devices for Neuromorphic Computing.

This study investigates the impact of spin-coating speed on the performance of carbon nanotube (CNT)-based optoelectronic synaptic devices, focusing on their long-term memory properties. CNT films fabricated at lower spin speeds exhibited a greater thickness and density compared to those at higher speeds. These denser films showed enhanced persistent photoconductivity, resulting in higher excitatory postsynaptic currents (EPSCs) and the prolonged retention of memory states after UV stimulation. Devices coated at a lower spin-coating speed of 2000 RPM maintained EPSCs above 70% for 3600 s, outperforming their higher-speed counterparts in long-term memory retention. Additionally, the study demonstrated that the learning efficiency improved with repeated UV stimulation, with fewer pulses needed to achieve the maximum EPSC in successive learning cycles. These findings highlight that optimizing spin-coating speeds can significantly enhance the performance of CNT-based synaptic devices, making them suitable for applications in neuromorphic computing and artificial neural networks requiring robust memory retention and efficient learning.

Effect of Spin Speed on the Physical Characteristics of CuO Films Synthesized by Sol–Gel Spin Coating for H2S Gas Sensing

Effect of Spin Speed on the Physical Characteristics of CuO Films Synthesized by Sol–Gel Spin Coating for H2S Gas Sensing

A flexible strategy to fabricate trumpet-shaped porous PDMS membranes for organ-on-chip application.

Porous polydimethylsiloxane (PDMS) membrane is a crucial element in organs-on-chips fabrication, supplying a unique substrate that can be used for the generation of tissue-tissue interfaces, separate co-culture, biomimetic stretch application, etc. However, the existing methods of through-hole PDMS membrane production are largely limited by labor-consuming processes and/or expensive equipment. Here, we propose an accessible and low-cost strategy to fabricate through-hole PDMS membranes with good controllability, which is performed via combining wet-etching and spin-coating processes. The porous membrane is obtained by spin-coating OS-20 diluted PDMS on an etched glass template with a columnar array structure. The pore size and thickness of the PDMS membrane can be adjusted flexibly via optimizing the template structure and spinning speed. In particular, compared to the traditional vertical through-hole structure of porous membranes, the membranes prepared by this method feature a trumpet-shaped structure, which allows for the generation of some unique bionic structures on organs-on-chips. When the trumpet-shape faces upward, the endothelium spreads at the bottom of the porous membrane, and intestinal cells form a villous structure, achieving the same effect as traditional methods. Conversely, when the trumpet-shape faces downward, intestinal cells spontaneously form a crypt-like structure, which is challenging to achieve with other methods. The proposed approach is simple, flexible with good reproducibility, and low-cost, which provides a new way to facilitate the building of multifunctional organ-on-chip systems and accelerate their translational applications.

Optimization of electrostatic seeding technique for wafer-scale diamond fabrication on β-Ga2O3

Integrating diamonds with β-Ga2O3 is a promising solution for addressing the problem of poor thermal conductivity and limited p-type dopability of β-Ga2O3. However, growing diamonds on β-Ga2O3 is challenging, especially without any interfacial layer, and achieving large-scale uniform diamond films is also tricky. This paper explores the vital role of an electrostatic seeding technique involving the use of Polydiallyldimethylammonium chloride (PDDAC) polymer with a positive zeta potential and diamond nano slurries with a negative zeta potential to facilitate the integration of diamond with β-Ga2O3. We conduct a detailed analysis of each step of this seeding technique, adjusting the spinning speed of the polymer coating, spinning period, baking period, and ultrasonication period to understand the underlying mechanisms preventing large-scale diamond growth and to identify strategies for achieving wafer-scale diamond fabrication on single crystal β-Ga2O3 film. This process facilitates the attainment of a uniform dispersion of diamond nanoparticles on β-Ga2O3 at a seeding density of ∼1.82 × 1011 cm−2. The optimized seeding technique has enabled the successful growth of wafer-scale diamond films on β-Ga2O3, as confirmed by scanning electron microscopy (SEM). Additionally, the high quality of the diamond film is affirmed by a quality factor of 96.75 % and a narrow full-width half maximum of 10.28 cm−1 in the T2g peak of the Raman spectra. The X-ray diffraction pattern reinforces the excellent quality of polycrystalline diamond films with minimum stress. In summary, this research provides valuable insights into the polymer-assisted electrostatic seeding technique, paving the way for the uniform growth of wafer-scale diamond films on β-Ga2O3, which is critical for realizing β-Ga2O3-based heterostructure devices.

Microstructure and Corrosion Study on Friction Surfaced Aluminum Alloy Coatings over Mild Steel

In this study, the low-carbon steel (AISI 1018 mild steel) substrate is coated with the aluminum alloys AA6082-T6, Al-20Zn, and Al-2Si-15SiC to improve its corrosion resistance by the friction surfacing (FS) technique. To produce a high-quality coating, friction surfacing process variables including spin speed, speed of travel, and the rate of feed are crucial. This experiment examines twelve friction-surfaced plates with different parameter combinations. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) examinations were carried out in order to comprehend the microstructure and chemical composition of the coating deposits and the area in contact between the coated surface and the substrate. Microstructure investigation reveals that the intermetallic combination of Fe-Al at the coating interface region is an effect of the elemental diffusion of Fe to aluminum at the contact interface. Then a uniform and fine-grained coating deposit is observed as a result of the continuous recrystallization of the consumable rod under frictional stress and heat generation. According to the outcomes of the microhardness test, the coated surface is roughly 15–16% harder than the consumable rod. The coating bond strength was measured using a ram tensile test, and it ranged from 102 MPa to 135 MPa. Finally, evaluation of corrosion behavior through immersion testing and pitting corrosion testing reveals that the coatings made of Al-20Zn and Al-2Si-15SiC exhibit good corrosive resistance in an alkaline environment.

Design and Characterization of Printed Flexible Humidity Sensor

The development of humidity sensors is essential for applications in the environmental, agriculture, medical and semiconductor industries [1-2]. The basic mechanism of humidity sensors is explained by a Grotthuss chain reaction, which is usually simplified as a proton-hopping process [3]. This refers to a dynamic charge transfer process at a certain relative humidity (RH). The humidity sensors can be of different types such as capacitive type, resistive, colorimetric and surface acoustic wave [4-7]. Capacitive type sensors are linear, require less complex circuitry and can operate for a wide range of humidity [8]. A typical capacitive type humidity sensor uses hydrophilic films as sensing layers which are stable at higher humidity levels [9]. Polymers that are being used for the fabrication of capacitive type humidity sensors include poly (2-hydroxyethyl methacrylate) (pHEMA) [9], cellulose acetate butyrate (CAB) [10], polyimide [11] and polymethyl methacrylate (PMMA) [12]. In this work, a humidity sensor has been fabricated on glass and flexible substrates.The design of humidity sensor consists of printed pattern of a conductor such as silver and a spin coated dielectric such as polymer poly (2-hydroxyethyl methacrylate) (p-HEMA) and polyimide. The printing of conductor was done in an interdigitated pattern as shown in figure 1. The thickness of sensitive materials was controlled by varying the spin time from 10 to 30 seconds. A thick solution of sensitive materials was prepared by adding a 3 gm of polymer in 50 mL ethanol in the case of p-HEMA. Currently we are preparing one more set of samples using polyimide and we will present a comparison of two humidity sensors- one with p-HEMA and another with polyimide. A humidity sensor that employs interdigitated capacitors (IDC) printed with silver on a glass and flexible substrate was successfully fabricated using p-HEMA and polyimide at spin speed of 2000 rpm for 20 seconds. Our goal is to integrate the humidity sensor into a robotic arm to perform real-time object characterization in agricultural applications via comprehensive understanding of the operations of harvesting robots in various crop types and environmental conditions.

Simulation-Guided Analysis towards Trench Depth Optimization for Enhanced Flexibility in Stretch-Free, Shape-Induced Interconnects for Flexible Electronics.

In this paper, we present an optimization of the planar manufacturing scheme for stretch-free, shape-induced metal interconnects to simplify fabrication with the aim of maximizing the flexibility in a structure regarding stress and strain. The formation of trenches between silicon islands is actively used in the lithographic process to create arc shape structures by spin coating resists into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear force Q(x), that usually leads to increased strains the structure can generate. For the fabrication, the filling of the trenches with resists is optimized by varying the spin speed. Compared to theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Spin speed correlations and the evolution of galaxy-halo systems

Spin speed correlations and the evolution of galaxy-halo systems

The role of Cu and film thickness on the photocatalytic activity of mesoporous spin coated TiO2 films

Most practical applications of photocatalysts will involve coatings on an inert support; here we have examined how copper doping of spin coated porous TiO2 films affects their physical characteristics and photocatalytic activity. The photocatalytic degradation of stearic acid was used as a measure of photocatalytic activity for catalysts spin coated from a sol-gel onto glass with 0, 0.1, 0.5, 1, 2.5 and 5 wt% copper introduced into the catalyst lattice before gelation. The effects of spin coating speed on film thickness, structure and band gap were studied and the nature of the copper incorporated into the films examined with XPS and XANES measurements. Increased spin coating speeds reduces the thickness of the deposited films from ∼ 50 μm to ∼ 20 μm until a spin speed of ∼ 3000 rpm at which point non-Newtonian behaviour of the gels prevents further reductions in film thickness. A larger effect on film thickness is the presence of the added copper nitrate which results in thinner films. After calcining, XANES shows the bulk of the copper to be in a Cu(II) state but at the surface of the thinnest, most active films XPS shows only Cu(I). Photocatalytic activity is much more strongly affected by the presence of the copper than the thickness of the films with 0.1 wt% Cu catalysts as much as 10 times more active than the undoped catalysts. Increasing the copper content, however, reduces activity until at ∼ 5 wt% activity is lower than for the pure TiO2 films.

Experimental study of the restitution coefficient of spherical particles

The restitution coefficient is a crucial indicator of energy dissipation. This article discusses the used restitution coefficients and presents a method to measure particle velocities before and after collisions using high-speed camera testing. The study primarily explores the influence of particle characteristics (collision velocity, collision angle, rotation speed, and collision material) on the restitution coefficient during collisions between spherical particles and a flat plate. The main focus is on studying how changes in collision angles impact the restitution coefficient. Different materials ball collision test examines the effects of steel balls, glass balls, and resin balls on the restitution coefficient. The data collected during the tests are processed by using various parameters to deduce the restitution coefficient during particle collisions. The article also analyzes the patterns of changes in the restitution coefficient for spherical particles under different collision conditions. Additionally, it derives the relationship between the restitution coefficient and different influencing factors, such as varying collision materials and initial speeds. The experimental results demonstrate a direct correlation between the restitution coefficient, the material of the particles under study, particle size, and particle spin speed.

A novel method for measuring roll angle

The precise measurement of the spin speed of a high-speed autonomous unmanned aerial vehicle (HSA-UAV) is a key element in mastering flight stability, and the measurement of roll angle is the key to determining the accuracy of navigation control systems. We put forward a novel method for measuring roll angle. This method starts from the time–frequency domain analysis of the output signal of the geomagnetic sensor, extracts the time–frequency ridge of the time–frequency matrix (TFM) to obtain the spin speed of the HSA-UAV, and reconstructs the output signal of the geomagnetic sensor. It can calculate the roll angle when the calibration parameters of the geomagnetic sensor are unknown and have good engineering practical value. In addition, we also propose an improved nonlinear short-time Fourier transform with high-frequency resolution and a forward penalty dynamic path ridge-extraction method with frequency jump suppression to extract instantaneous frequency in the TFM.

Spin-Coating Fabrication Method of PDMS/NdFeB Composites Using Chitosan/PCL Coating.

This paper verified the possibility of applying chitosan and/or ferulic acid or polycaprolactone (PCL)-based coatings to polydimethylsiloxane/neodymium-iron-boron (PDMS/NdFeB) composites using the spin-coating method. The surface modification of magnetic composites by biofunctional layers allows for the preparation of materials for biomedical applications. Biofunctional layered magnetic composites were obtained in three steps. The spin-coating method with various parameters (time and spin speed) was used to apply different substances to the surface of the composites. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to analyze the thickness and surface topography. The contact angle of the obtained surfaces was tested. Increasing spin speed and increasing process time for the same speed resulted in decreasing the composite's thickness. The linear and surface roughness for the prepared coatings were approximately 0.2 μm and 0.01 μm, respectively, which are desirable values in the context of biocompatibility. The contact angle test results showed that both the addition of chitosan and PCL to PDMS have reduced the contact angle θ from 105° for non-coated composite to θ~59-88° depending on the coating. The performed modifications gave promising results mainly due to making the surface hydrophilic, which is a desirable feature of projected biomaterials.

Nitrogen-doped graphene quantum dots/ polyvinyl alcohol nanocomposite for photon management: Application in CIGS photovoltaic cells

The efficiency (η) of copper indium gallium selenide (CIGS) solar cells has been hampered by absorption losses that happen within the ZnO and CdS layers. A photon downconversion layer created from polyvinyl alcohol (PVA) and nitrogen-doped graphene quantum dots (NGQDs) composite (NGQDs/PVA) was implemented on the top of the cell to overcome this obstacle. Notably, the NGQDs/PVA layers, prepared at spin speeds of 3000, 4000, and 5000 rpm, exhibited optimal characteristics, demonstrating superior light absorption at low wavelengths along with elevated transmittance at longer wavelengths. The η was found to be highest for the layer prepared at 4000 rpm, accompanied by elevated values of short-circuit current (Jsc), open-circuit voltage (Voc), and fill factor (FF). Consequently, Cell #2 incorporating the champion NGQDs/PVA layer outperformed all other CIGS photovoltaic cells, showcasing an impressive enhancement of 8.96 % in Jsc, 1.62 % in Voc, 2.03 % in FF, and an overall η of 11.51 %. This champion cell significantly improves the performance of CIGS photovoltaics.