Specific Biogas Yield Research Articles

Investigating role of corn stover biochar supplementation on continuous pilot scale anaerobic digestion: Performance and microbial community dynamics

Biochar supplementation could facilitate microbial colonization and increase biogas and methane yield in anaerobic digestion (AD). This study investigated the impact of corn stover biochar (CSB) augmentation on the continuous pilot scale AD of rice straw. The CSB supplementation exhibited the daily average specific biogas and methane yield of 368.6 L/kg volatile solids (VS) and 230 L/kg VS, which were 35% and 37% higher than the control. Principle component analysis indicated that the VS reduction positively correlated with the daily average specific biogas and methane yield. Metagenomic analysis revealed that the CSB supplementation facilitated microbial colonization with the enrichment of unclassified genera from families Planococcaceae, Clostridiaceae, and Ruminococcaceae, and genus Clostridium and methanogenic archaea (Methanosarcina and Methanobacterium). The co-occurrence network revealed a notable shift in microbial interactions following the supplementation of CSB as an additive in AD. These results offer insights for enhancing the performance of the AD using CSB.

Evaluation of Biochemical Methane Potential and Kinetics of Organic Waste Streams for Enhanced Biogas Production

Organic waste has the potential to produce methane gas as a substitute for petrol-based fuels, while reducing landfilling and possible environmental pollution. Generally, anaerobic digestion (AD) is used only in wastewater treatment plants as a tertiary stage of sewage sludge treatment, generating a fraction of the energy that such process plants require. In this study, four different wastes—food waste (FW), dairy industry waste (DIW), brewery waste (BW), and cardboard waste (CBW)—were tested for biogas production. The biochemical methane potential (BMP) of each sample was evaluated using an automatic methane potential system (AMPTS). Operating parameters such as pH, temperature, total solids, and volatile solids were measured. Experiments on the anaerobic digestion of the samples were monitored under mesophilic conditions (temperature 37 °C, retention time 30 days). Specific methane yields (SMYs), as well as the theoretical methane potential (BMPth), were used to calculate the biodegradability of the substrates, obtaining the highest biodegradability for BW at 95.1% and producing 462.3 ± 1.25 NmL CH4/g volatile solids (VS), followed by FW at an inoculum-to-substrate ratio (ISR) of 2 at 84% generating 391.3 NmLCH4/g VS. The BMP test of the dairy industry waste at an inoculum-to-substrate ratio of 1 was heavily inhibited by bacteria overloading of the easily degradable organic matter, obtaining a total methane production of 106.3 NmL CH4/g VS and a biodegradability index of 24.8%. The kinetic modeling study demonstrated that the best-fitting model was the modified Gompertz model, presenting the highest coefficient of determination (R2) values, the lowest root means square error (RMSE) values for five of the substrates, and the best specific biogas yield estimation with a percentage difference ranging from 0.3 to 3.6%.

Effect of mowing versus abandonment of mesic grasslands in Central Europe on biomass use for biogas production: Implications for semi-natural ecosystem conservation

The economic management of lignocellulosic biomass from semi-natural grasslands is now a challenge across Europe. The abandonment of mowing these grasslands leads to the gradual degradation of these ecosystems. This study investigates how chemical and biological factors affect the suitability of biomass from abandoned grasslands for biogas production. We sampled 30 mown and 30 abandoned grassland sites in the Sudetes Mountains (Poland and Czechia). The cover contribution of short herbs was found to be significantly higher in mown grasslands (p < 0.001), while that of tall herbs was more prevalent in abandoned grasslands (p < 0.01). The specific biogas yield (SBY, NL kg−1 volatile solids) is negatively affected by an increased percentage of herbs in the biomass of mown and abandoned grasslands. This is due to the inhibitory effect of herbs on biodegradation, the increase in lignin content and the decrease in cellulose. This study highlights the importance of individual plant species in assessing grassland biomass for area biogas yield (ABY, m3 ha−1) and provides new insights into a field that has not yet been extensively investigated. In mown grasslands, ABY was most positively correlated with grass species (Arrhenatherum elatius, Trisetum flavescens and Festuca pratensis). In abandoned grasslands, the ABY was most correlated with herbaceous species (Galium aparine, Urtica dioica and Chaerophyllum aromaticum) and grasses (A. elatius and Elymus repens). Mown grasslands had significantly higher species richness (p < 0.001) compared to abandoned grasslands, but the number of species sampled did not correlate with SBY and ABY. This study contributes to the development of a sustainable bio-economy by highlighting the need for efficient use of grassland biomass. This approach helps protect semi-natural ecosystems and facilitates sustainable management of renewable resources.

Effect of long-term storage of cattle manure on its energy potential and biodegradability

Abstract In recent years in Russia, due to the complicated geopolitical situation in some border areas, biogas plants have been considered not only as waste utilization facilities, but also as reserve energy sources, which are safer than traditional - nuclear power plants. In this context, the development of an algorithm for the flexible operation of a biogas plant is particularly relevant, which gives rise to the need to study the stability of the system under the influence of different unfavourable factors. In this work, the influence of long-term storage of cattle manure on its energy potential and biodegradability is studied. The specific methane yield in the test variant with manure stored for 10 months before anaerobic fermentation was 1.41±0.55 ml/g oDM, which is 6.23 times lower than in the test variant with fresh manure; the methane content of manure after long-term storage is 9.66 times lower and the degree of decomposition of its organic matter is 2.72 times lower compared to similar indicators of manure processed without preliminary storage. However, the specific biogas yield from long-term stored manure is 1.66 times higher than the control, which indicates intensive formation of other gases. Thus, long-term storage has a negative impact on the energy potential of cattle manure; if it is necessary to process it in a biogas plant, it is advisable to combine it with more energy-intensive raw materials.

A novel player of methylotrophic methanogensis pathway in boosting anaerobic digestion of corn stover with effluents recycling

Effluents recycling proves to be an effective method for enhancing the performance of anaerobic digestion system for lignocellulosic-like biomass. However, a limited understanding exists regarding the regulation mechanisms of methanogens. This study aims to systematically assess the dynamic interactions between process parameters, microbial communities, and methanogenic activity throughout the AD process of corn stover with effluents recycling. The results show a significant increase in the specific biogas yields of corn stover to 369 ± 115 mL/g VS with effluents recycling, an 87 % improvement compared to the control system. Effluents recycling can recover nitrogen and selectively enrich the abundances of microorganisms such as Herbinix hemicellulosilytica, Bacteroides paurosaccharolyticus and Methanosarcina mazei, etc. Correspondingly, the strategy improves the abundance of CAZymes, enhancing the efficient depolymerization of cellulose, glucuronoarabinoxylan, xyloglucan and pectin. Methanol and methylamines originating from enhanced pectin hydrolyzation and the biogenic amine pathway boost methylotrophic methanogenesis. This study addresses knowledge gaps in producing-pathways of precursors for methylotrophic methanogenesis and elucidates the mechanism to boost methanogenesis process of lignocellulosic-like biomass with effluents recycling.

Application of Recycled Filling to Improve the Purification Performance of Confectionery Wastewater in a Vertical Anaerobic Labyrinth Flow Bioreactor

Anaerobic wastewater treatment is, in many cases, a justified alternative to typical activated sludge processes, from a technological, economic, and ecological point of view. The optimisation of fermentation reactors is primarily concerned with increasing the biodegradation of organic compounds and biogas production, as well as improving efficiency in the removal of nitrogen and phosphorus compounds. The aim of the research was to determine the impact of using low-cost recycled filling on the efficiency of treating real confectionery wastewater in a vertical anaerobic labyrinth flow bioreactor. The experiments focused on selecting the organic loading rate that would allow for the effective biodegradation and removal of pollutants, as well as the efficient production of biomethane. It was found that the tested reactor can operate efficiently at a maximum organic loading rate (OLR) of 7.0–8.0 g of chemical oxygen demand (COD)/L·d. In this OLR range, high efficiency was guaranteed for both wastewater treatment and biogas production. However, increasing the OLR value to 8.0 g COD/L·d had a significant negative effect on the methane (CH4) content in the biogas. The most efficient variants achieved a biodegradation efficiency of around 90% of the organic compounds, a CH4 content of over 70% in the biogas, and a biogas yield of over 400 L/kg of COD removed. A significant influence of the applied OLR on the ratio of free organic acids (FOS) to total alkaline capacity (TAC) and pH was observed, as well as a strong correlation of these indicators with the specific biogas yield and CH4 content. The application of a solution based on the use of a hybrid system of anaerobic granulated sludge and an anaerobic filter resulted in an efficient treatment process and an almost complete elimination of suspensions from the wastewater.

Optimizing Biogas Production and Digestive Stability through Waste Co-Digestion

This study aimed to enhance the nutrient balance of municipal solid waste (MSW), characterized by a high carbon-to-nitrogen (C/N) ratio, which is a critical factor in the anaerobic digestion process. The investigation involved the addition of MSW, which is rich in carbon content, to food waste (FW) with high nitrogen content. The goal was to determine an optimal co-substrate mixing ratio of MSW and FW for anaerobic co-digestion at mesophilic temperatures, aiming to improve process stability and performance to achieve higher biogas yield. The co-digestion experiments encompassed five mixing ratios of MSW and FW with C/N ratios of 20, 25, 30, 35, and 40 under mesophilic conditions in a laboratory. The results indicated that the highest specific biogas yield, reaching 827 L/kg VS, was attained when the co-substrate feedstock had a balanced C/N ratio of 20, surpassing the 520 L/kg vs. obtained from MSW digestion alone. As the proportion of MSW increased in the co-substrate mixing feedstock, the biogas production rate decreased. Additionally, the study explored the optimal substrate-to-inoculum (S/I) ratio, focusing on the co-substrate feedstock with a C/N ratio of 20. Four S/I ratios (0.5, 1.0, 1.5, and 2.0) were examined, revealing that the highest specific biogas yield, at 642 L/kg VS, occurred at an S/I ratio of 0.5. An accumulation in volatile fatty acids (VFAs) was observed at higher S/I ratios, attributed to the lower abundance of inoculum microorganisms in the anaerobic digestion process. Overall, the findings suggested that the optimum C/N ratio for co-digestion of MSW and FW falls within the range of 20–25/1, while the preferred S/I ratio is 0.5.

Possibilities of Utilising Biomass Collected from Road Verges to Produce Biogas and Biodiesel

Grass collected as part of roadside maintenance is conventionally subjected to composting, which has the disadvantage of generating significant CO2 emissions. Thus, it is crucial to find an alternative method for the utilisation of grass waste. The aim of this study was to determine the specific biogas yield (SBY) from the anaerobic mono-digestion of grass from road verges and to assess the content of Fatty Acid Methyl Esters (FAMEs) in grass in relation to the time of cutting and the preservation method of the studied material. The biochemical biogas potential (BBP) test and the FAMEs content were performed on fresh and ensiled grass collected in spring, summer, and autumn. The highest biogas production was obtained from fresh grass cut in spring (715.05 ± 26.43 NL kgVS−1), while the minimum SBY was observed for fresh grass cut in summer (540.19 ± 24.32 NL kgVS−1). The methane (CH4) content in the biogas ranged between 55.0 ± 2.0% and 60.0 ± 1.0%. The contents of ammonia (NH3) and hydrogen sulphide (H2S) in biogas remained below the threshold values for these inhibitors. The highest level of total FAMEs was determined in fresh grass cut in autumn (98.08 ± 19.25 mg gDM−1), while the lowest level was detected in fresh grass cut in spring (56.37 ± 7.03 mg gDM−1). C16:0 and C18:0, which are ideal for biofuel production, were present in the largest amount (66.87 ± 15.56 mg gDM−1) in fresh grass cut in autumn. The ensiling process significantly impacted the content of total FAMEs in spring grass, leading to a reduction in total saturated fatty acids (SFAs) and an increase in total unsaturated fatty acids (USFAs). We conclude that grass biomass collected during the maintenance of road verges is a valuable feedstock for the production of both liquid and gaseous biofuels; however, generating energy from biogas appears to be more efficient than producing biodiesel.

ЭНЕРГЕТИЧЕСКИЙ ПОТЕНЦИАЛ И ОСОБЕННОСТИ БИОДЕГРАДАЦИИ ЗЕРНОВОЙ ПЫЛИ ПРИ ЕЕ ПЕРЕРАБОТКЕ В БИОГАЗ

The composition of the dust that is generated during the collection, transportation, processing and storage of grain is different and complex. The amount of grain dust can reach 26% by weight of the raw material. Due to the ability to ignite spontaneously, it is classified as a hazard class 3, and if it enters the human body, it can cause harm to health, therefore, grain processing enterprises take measures to reduce the concentration of grain dust in the air. On the other hand, the dust generated during grain processing is, due to its chemical composition, a valua- ble raw material, the loss of which is undesirable. The world literature describes such methods for processing aspiration grain dust as hydrolysis and the preparation of nutrient media for microorganisms, briquetting and combustion, use in composting, as well as conversion into biogas. The purpose of this work is to study the features of processing aspiration grain dusts of various agricultural crops into biogas and determine their energy potential and biodegradability. As a result of our laboratory studies, it was established that the specific biogas and methane yield from soybean grain dust was 186.37±58.89 – 230.30±21.90 and 95.54±36.95 – 122.17±15.39 ml/g VS respectively; from barley grain dust – 165.06±9.37 – 191.41±5.65 and 86.45±6.37 – 100.18±6.65 ml/g VS respectively. The concentration of methane in biogas in different variants ranged from 46.75±7.14 to 52.75±1.60%. When recycling 1 ton of these grain dusts at a biogas station, you can get from 278.70 to 382.25 kW of electrical energy and from 285.50 to 391.57 kW of thermal energy. The degree of decomposition of organic matter of substrates in our study is generally low – from 5.61±0.08 to 5.91±0.37%. Thus, it has been established that the grain dusts studied in this work can be considered as a promising cosubstrats for existing or planned biogas stations. The recommended processing time is no more than 35 days.

Life cycle assessment of sludge anaerobic digestion combined with land application treatment route: Greenhouse gas emission and reduction potential

Sewage sludge treatment and disposal is essential for water environment protection and pollution management. Coupling anaerobic digestion with land application offers a promising solution to recycle energy and resources to reduce greenhouse gas(GHG) emissions. However, the comprehensive assessment of the anaerobic digestion treatment route on GHG emissions and reduction potential is lacking. This study used life cycle assessment(LCA) to evaluate the GHG emissions based on two cases. The GHG emissions resulting from the digested sludge land application was considered, and the reduction potentials resulting from biogas utilization and substituting chemical fertilizers were also analyzed. The results showed the net GHG emissions of the two cases were 178.92 and − 26.33 kg CO2-eq/tDS, respectively. When excluding the reduction, the GHG emissions of the two cases were 519.32 and 352.97 kg CO2-eq/tDS, respectively, where the dewatering, digested sludge drying, and land application were the main contributors. The GHG emissions associated with the digested sludge land application accounted for 28% and 45% of the total GHG emissions in two cases, respectively. The GHG emission reduction could be achieved by sludge substitution for chemical fertilizer, which could offset 65.5% and 107.5% of the total GHG emissions in two cases, respectively. While the biogas utilization could only offset less than 10% of the total GHG emissions of both cases. Likewise, improving organic content or specific biogas yield rates could only offset up to 26.2% and 40.3% of the total GHG emissions. These findings provide understanding into evaluating GHG emissions of the sludge anaerobic digestion treatment route.

Impact of Thermo-Mechanical Pretreatment of Sargassum muticum on Anaerobic Co-Digestion with Wheat Straw

Sargassum muticum (SM) is an invasive macroalgal species seasonally occurring in large quantities. While generally suitable for anaerobic digestion, recent studies resulted in low specific methane yields (SMYs), presumably due to salt, polyphenol, and high fiber contents of this marine biomass. In this study, the specific biogas yield (SBY) and SMY of SM alone as well as in co-digestion with wheat straw (WS) were investigated in batch tests at process temperatures of 44 ± 1.4 °C with a retention time of approx. 40 d. The pretreatment variants of SM were examined with regard to desalination and disintegration to potentially improve digestibility and to enhance the overall performance in anaerobic digestion. A sole mechanical treatment (pressing) and a thermo-mechanical treatment (heating and pressing) were tested. Batch assays showed that pressing increased the SMY by 15.1% whereas heating and pressing decreased the SMY by 15.7% compared to the untreated variant (87.64 ± 8.72 mL/gVS). Both anaerobic digestion experiments generally showed that co-digestion with WS can be recommended for SM, but the observed SBY and SMY were still similar to those of other studies in which SM was not pretreated. The mechanical pretreatment of SM, however, offers the potential to enhance the SMY in the anaerobic digestion of SM with WS, but further research is necessary to identify the optimum upgrading approaches since the overall SMY of SM is relatively low compared to other substrates that are commonly used in anaerobic digestion. In addition to anaerobic digestion, SM as an already available biomass could also be of interest for further utilization approaches such as fiber production.

Pretreatment of Slaughterhouse Effluent Treatment Plant Sludge Using Electro-Fenton Process for Anaerobic Digestion

Sludge management is an integral process of an effluent treatment plant (ETP). This study aimed at using the electro-Fenton (EF) process for pretreatment of a cattle-based slaughterhouse ETP sludge to enhance biogas production from anaerobic digestion. EF-oxidation experiments were conducted in 0.5 L beakers with mild-steel electrodes, to study the effect of factors, viz., H2O2 concentration, current density and reaction time on soluble chemical oxygen demand (sCOD) concentration, soluble extracellular polymeric substances (sEPS) concentration and volatile suspended solids (VSS) removal efficiency. This was followed by the quantification of biogas production from the raw and pretreated sludge in anaerobic digestion (AD). Experimental conditions for the EF process were optimized using response surface methodology (RSM). At optimized experimental conditions, EF pretreatment resulted in an increase in sCOD and sEPS concentrations, from 0.91 g/L to 6.1 g/L and 0.18 g/L to 1.4 g/L, respectively. VSS removal efficiency was 68.1%. Batch anaerobic digestion studies demonstrated an enhancement in the specific biogas yield, from 110 NmL/g-VS to 460 NmL/g-VS.

Thermogravimetric substrate analysis for prediction of biogas and methane yields

Biodegradability of biomass constituents is the reason for the gap between theoretical biogas/methane yield and the maximum yield obtainable in bioconversion. The prediction of biogas/methane yields by applying thermal analysis is a relatively new development in this field. The aim of this study was to develop a bioconversion model based on thermogravimetry. Eleven substrates with a specific biogas yield within the range 104 to 572 mLN per gram of volatile solids were subjected to thermogravimetry and a multi linear regression model was developed to predict biogas and methane yields. The optimum parameters describe biogas and methane yields with a root mean square error of 58.8 and 34.3 mLN per gram of volatile solids respectively. The coefficient of determination for these two datasets was 0.81 and 0.84. A prediction technique based on thermogravimetric analysis appears to be a good alternative to other prediction models.

Significance of Intermittent Mixing in Mesophilic Anaerobic Digester

The mixing of slurry in an anaerobic digester (AD) is one of many key parameters, which have a significant effect on specific biogas yield (BY) and volatile solid (VS) removal rate. The determination of the optimum mixing regime in a digester is very complex as it depends on a large number of internal and external factors such as microbial community, the rheology of slurry, digester and impeller design, mixing intensity, and mixing intervals. The novelty of this study is the investigation of the optimum mixing regime in a lab-scale digester under semi-continuous mixing regimes by the continuous monitoring of the physicochemical properties of the digestate. In this study, a helical ribbon (HR) impeller was used for the agitation of the slurry operated at 67 rpm for 5 min under various agitation intervals (1 h, 2 h, 3 h, and 4 h). The results showed a 6–12% reduction in BY as the time between mixing operations increased. The highest BY was observed at a mixing frequency of 5 min/h, which produced a total of 54.1 L of biogas as compared to the mixing frequencies of 2 h, 3 h, and 4 h, where the BYs were recorded as 51.2 L, 49.8 L, and 47.3 L, respectively. Volatile fatty acids (VFAs) and FOS/TAC ratio were stabilized at 5–7 Gl−1 and 0.3–0.5, respectively. The appropriate mixing intensity was determined to obtain the highest biogas production, which could lead to lower power consumption for mixing operations.

Experimental evaluation of the influence of combined particle size pretreatment and Fe3O4 additive on fuel yields of Arachis Hypogea shells.

A smart energy recovery process can achieve maximum energy recovery from organic wastes. Pretreatment of feedstock is essential to biogas and methane yields during the anaerobic digestion process. This work combined particle size reduction with Fe3O4 nanoparticles to investigate their influence on biogas and methane yields from anaerobic digestion of Arachis hypogea shells. Twenty milligrams per litre of Fe3O4 nanoparticles was implemented with 2, 4, 6 and 8 mm particle sizes and a single treatment of Fe3O4 for 35 days. The treatments were compared with each other and were discovered to significantly (p < 0.05) enhance biogas yield by 37.40%, 50.10%, 54.40%, 51.40% and 35.50% compared with control, respectively. Specific biogas yield recorded was 966.2, 1406, 1552.7, 1317.4, 766.2 and 413 mL g-1 volatile solid. This study showed the combination of Fe3O4 with 6 mm particle size of Arachis hypogea shells produced the optimum biogas and methane yields. The addition of Fe3O4 to particle sizes below 6 mm resulted in over-accumulation of volatile fatty acids and lowered the gas yield. This can be applied on an industrial scale.

Effect of the Substrate to Inoculum Ratios on the Kinetics of Biogas Production during the Mesophilic Anaerobic Digestion of Food Waste

This study evaluates the effects of the varying substrate to inoculum ratios (S:I) of 0.5, 1, 2, 3, 4, 5, and 6 (volatile solids/VS basis) on the kinetics of biogas production during batch mesophilic (35 ± 1 °C) anaerobic digestion (AD) of simulated food waste (FW), using anaerobic digestate as the inoculum. Kinetic parameters during biogas production (scrubbed with NaOH solution) are predicted by the first-order and the modified Gompertz model. The observed average specific biogas yields are in descending order corresponding to the S:I ratios 1, 2, 4, 6, 3, 5, and 0.5, respectively, and the significant effect of the S:I ratio was observed. The tests with the S:I of 1 have the maximum average biogas production rates of 88.56 NmL/gVS.d, whereas tests with the S:I of 6 exhibited the lowest production rates (24.61 NmL/gVS.d). The maximum biogas yields, predicted by the first order and the modified Gompertz model, are 668.65 NmL/gVS (experimental 674.40 ± 29.10 NmL/gVS) and 653.17 NmL/gVS, respectively. The modified Gompertz model has been proven to be suitable in predicting biogas production from FW. VS removal efficiency is greater in higher S:I ratios, with a maximum of 78.80 % at the S:I ratio of 6, supported by the longer incubation time. Moreover, a significant effect of the S:I ratio is seen on kinetics and energy recovery from the AD of FW.

Designing a Biogas Plant for an Educational and Scientific Livestock Complex

To design biogas plants, it is necessary to have accurate data about the properties and biogas productivity of the available substrates. Reference data should not be used because the performance of the same substrate can vary significantly. In this research,chicken, horse, sheep and rabbit manure from one of the farms inthe Belgorod region of Russia were analyzed, and the parameters of a biogas station for the processing of this raw material were calculated.The biogas yield of the substrates was determined using the Hohenheim Biogas Yield Test. It was found that the specific biogas yield from the droppings of broilers, laying hens, rabbits, sheep, and horses, and from corn silage were, respectively, 456, 363, 390, 189, 116 and 618 ml/g оDM. The methane content in the biogas was 58.00, 58.50, 57.00, 62.00, 65.00 and 53.60%, respectively. In most cases, the obtained results differed significantly from the data presented in publications of other researchers and reference books.The biogas plant parameter calculations were made according to generally accepted equations, taking into account the characteristics of the studied substrates. Based on the results, it can be concluded that to dispose of the animal excrement of this farm, it is necessary to build a biogas plant with a bioreactor of volume 102.2 m3 and an engine with a power of 12 to 31 kW. The planned output of electric and thermal energy would be 246.19 and 410.27 kWh/day, respectively.&#x0D; Keywords: Hohenheim Biogas Yield Test, rabbit manure, horse dung, sheep manure, chicken droppings, biogas yield of substrates

Energy rationale for the Use of the Thermophilic Mode of Anaerobic Bioconversion of Liquid Organic Waste in the Climatic Conditions of the Russian Federation

The transition of livestock production to industrial processes and the concentration of animals associated with this process on large farms and complexes has caused a sharp increase in the volume of manure that must be disposed of without pollution. One of the ways of processing organic waste (biomass) is its anaerobic digestion in biogas plants through the vital activity of microorganisms (methanogenesis).Biogas obtained using microbiological processing of biomass can be used as a raw material for heat and electric energy. Annually, 0.17% of the total livestock manure produced at Russian agricultural enterprisesis used for biogas production.The main component of a biogas plant is a manure fermentation reactor, the required volume of which is determined by the daily output of manure from the livestock farm, the temperature and the hydraulic retention time of treatment. This research explored thermal energy consumption of biogas plants, using the example of a biogas plant of a modular design that depended on the average annual outdoor temperature. Based on the calculations, the thermophilic mode was found to be more energy-efficient than the mesophilic one; thus, with the thermophilic mode, the specific energy consumption needed for the plant was lower at the average annual outdoor temperatures of all the constituent entities of the Russian Federation. At the same time, the specific biogas yield in the thermophilic regime was 20-50%higher than in the mesophilic regime.&#x0D; Keywords: anaerobic processing, agricultural waste, thermophilicmode, mesophilicmode, energy costs, energy rationale

Monitoring of Food Waste Anaerobic Digestion Performance: Conventional Co-Substrates vs. Unmarketable Biochar Additions.

This study proposed the selection of cost-effective additives generated from different activity sectors to enhance and stabilize the start-up, as well as the transitional phases, of semi-continuous food waste (FW) anaerobic digestion. The results showed that combining agricultural waste mixtures including wheat straw (WS) and cattle manure (CM) boosted the process performance and generated up to 95% higher methane yield compared to the control reactors (mono-digested FW) under an organic loading rate (OLR) range of 2 to 3 kg VS/m3·d. Whereas R3 amended with unmarketable biochar (UBc), to around 10% of the initial fresh mass inserted, showed a significant process enhancement during the transitional phase, and more particularly at an OLR of 4 kg VS/m3·d, it was revealed that under these experimental conditions, FW reactors including UBc showed an increase of 144% in terms of specific biogas yield (SBY) compared to FW reactors fed with agricultural residue. Hence, both agricultural and industrial waste were efficacious when it came to boosting either FW anaerobic performance or AD effluent quality. Although each co-substrate performed under specific experimental conditions, this feature provides decision makers with diverse alternatives to implement a sustainable organic waste management system, conveying sufficient technical details to draw up appropriate designs for the recovery of various types of organic residue.

Possibilities of Obtaining Biogas from Manure and Amaranth

Introduction. The use of biomass allows increasing the rate of biogas formation and its specific yield. This work aims to study the kinetics of methanogenesis and determine the optimal duration of digestion and organic load, which are the main indicators of the technological process of biogas formation. Materials and Methods. The substrate (dairy manure, biomass of amaranth) was the study object. Experimental studies were carried out using a laboratory biogas plant. The computer program (certificate No. 2018662045) was used to obtain modified Gompertz models describing the kinetics of biogas formation. Based on the obtained data, the hydraulic retention time and organic loading rate (the key parameters in the design of biogas plants were determined). Results. The paper presents the experimental studies results of the biogas formation kinetics when using dry amaranth biomass. The Gompertz mathematical models were obtained. Methane-tank control parameters (hydraulic retention time and organic loading rate) were obtained for anaerobic digestion of a new substrate. Discussion and Conclusion. The use of new co-substrate Amaranthus retroflexus L. allowed increasing the specific biogas yield from dairy manure by 52.2 % and the ultrasonic pre-treatment in combination with the herbal supplement by 89.1 %. The optimal hydraulic retention time value was 10 days and organic loading rate was 4.1 kg of volatile solids per m3 of digester per day.