Small Area Devices Research Articles

Aromatic carboxyl acid regulated nanoparticle deposition and passivation of tin oxide for high performance perovskite solar cells

The composition and nano particle agglomeration of hydrolyzed species in chemical bath deposition (CBD) plays a key role in obtaining efficient SnO2 film for high performance perovskite solar cells (PSCs). In this work, the aromatic acids with varied carboxyl groups were investigated to regulate the nano particle deposition and passivate the buried SnO2/perovskite interface. The quasi in-situ dynamic light scattering and Zeta potential results indicated that the nano particle agglomeration with trimesic acid (TMA) was significantly refined throughout the whole deposition process. The TMA-SnO2 achieved an ideal energy band alignment with perovskite and released the internal residual strain, promoting the growth and crystallization of the perovskite film due to the corrdination of carboxyl groups. As a result, the interface defects were effectively passivated with enhanced efficiency and stability. The small area device based on TMA-SnO2 obtained an efficiency of 25.07 %. The devices with an enlarged area of 1.4 cm2 and the 5x5 cm2 mini-module (active area 10.054 cm2) showed impressive PCEs of 23.93 % and 22.40 %, respectively. Furthermore, the unencapsulated devices exhibit enhanced long-term stability, maintaining 80 % and 90 % of the initial efficiencies under 80 ± 5°C thermal annealing in nitrogen for 1176 h and in air condition for 3224 h, respectively.

Constraining the Excessive Aggregation of Non-Fullerene Acceptor Molecules Enables Organic Solar Modules with the Efficiency >16.

Translating high-performance organic solar cell (OSC) materials from spin-coating to scalable processing is imperative for advancing organic photovoltaics. For bridging the gap between laboratory research and industrialization, it is essential to understand the structural formation dynamics within the photoactive layer during printing processes. In this study, two typical printing-compatible solvents in the doctor-blading process are employed to explore the intricate mechanisms governing the thin-film formation in the state-of-the-art photovoltaic system PM6:L8-BO. Our findings highlight the synergistic influence of both the donor polymer PM6 and the solvent with a high boiling point on the structural dynamics of L8-BO within the photoactive layer, significantly influencing its morphological properties. The optimized processing strategy effectively suppresses the excessive aggregation of L8-BO during the slow drying process in doctor-blading, enhancing thin-film crystallization with preferential molecular orientation. These improvements facilitate more efficient charge transport, suppress thin-film defects and charge recombination, and finally enhance the upscaling potential. Consequently, the optimized PM6:L8-BO OSCs demonstrate power conversion efficiencies of 18.42% in small-area devices (0.064 cm2) and 16.02% in modules (11.70 cm2), respectively. Overall, this research provides valuable insights into the interplay among thin-film formation kinetics, structure dynamics, and device performance in scalable processing.

Advances and Challenges in Large-Area Perovskite Light-Emitting Diodes.

Metal halide perovskite light-emitting diodes (PeLEDs) have shown promise for high-definition displays and flat-panel lighting because of their wide color gamut, narrow emission band, and high brightness. The external quantum efficiency of PeLEDs increased rapidly from ≈1% to more than 25% in the past few years. However, most of these high-performance devices are fabricated using a spin coating method with a small device area of <0.1 cm2, limiting their commercial applications. Recently, large-area PeLEDs have attracted growing attention and significant breakthroughs have been reported. This perspective first introduces the pros and cons of each technique in making large-area PeLEDs. The advances in the fabrication of large-area PeLEDs are then summarized using spin coating and mass-production methods such as inkjet printing, blade coating, and thermal evaporation. Moreover, the challenging issues will be discussed that are urgent to be solved for large-area PeLEDs.

Radiation Damage on Silicon Photomultipliers from Ionizing and Non-Ionizing Radiation of Low-Earth Orbit Operations.

Silicon Photomultipliers (SiPMs) are single photon detectors that gained increasing interest in many applications as an alternative to photomultiplier tubes. In the field of space experiments, where volume, weight and power consumption are a major constraint, their advantages like compactness, ruggedness, and their potential to achieve high quantum efficiency from UV to NIR makes them ideal candidates for spaceborne, low photon flux detectors. During space missions however, SiPMs are usually exposed to high levels of radiation, both ionizing and non-ionizing, which can deteriorate the performance of these detectors over time. The goal of this work is to compare process and layout variation of SiPMs in terms of their radiation damage effects to identify the features that helps reduce the deterioration of the performance and develop the next generation of more radiation-tolerant detectors. To do this, we used protons and X-rays to irradiate several Near Ultraviolet High-Density (NUV-HD) SiPMs with small areas (single microcell, 0.2 × 0.2 mm2 and 1 × 1 mm2) produced at Fondazione Bruno Kessler (FBK), Italy. We performed online current-voltage measurements right after each irradiation step, and a complete functional characterization before and after irradiation. We observed that the main contribution to performance degradation in space applications comes from proton damage in the form of an increase in primary dark count rate (DCR) proportional to the proton fluence and a reduction in activation energy. In this context, small active area devices show a lower DCR before and after irradiation, and we propose light or charge-focusing mechanisms as future developments for high-sensitivity radiation-tolerant detectors.

Advancements in Scaling Up Perovskite Solar Cells: From Small-Area Devices to Large-Scale Modules.

The power conversion efficiency (PCE) of perovskite solar cells (PSCs) has exceeded those of conventional thin-film solar cell technologies, and the speed at which this increase has been achieved is unprecedented in the history of photovoltaics. Despite the significant progress achieved by PSCs at the laboratory level, their commercial prospects still face two significant challenges: scaling up in size and ensuring long-term stability. Small-area devices (~1 cm2) are typically fabricated using spin-coating. However, this approach may not be suitable for preparing the large-area (>100 cm2) substrates required for commercialization. Thus, new materials and methods must be developed to facilitate the coating of large-area PSCs. This review will discuss the development of scaling up organic-inorganic hybrid PSCs and the challenges of increasing the device area. Furthermore, it will provide an overview of the methodologies for achieving high-efficiency perovskite solar modules.

Scalable CIGS Solar Cells Employing a New Device Design of Nontoxic Buffer Layer and Microgrid Electrode.

The efficiency of copper indium gallium selenide (CIGS) solar cells that use transparent conductive oxide (TCO) as the top electrode decreases significantly as the device area increases owing to the poor electrical properties of TCO. Therefore, high-efficiency, large-area CIGS solar cells require the development of a novel top electrode with high transmittance and conductivity. In this study, a microgrid/TCO hybrid electrode is designed to minimize the optical and resistive losses that may occur in the top electrode of a CIGS solar cell. In addition, the buffer layer of the CIGS solar cells is changed from the conventional CdS buffer to a dry-processed wide-band gap ZnMgO (ZMO) buffer, resulting in increased device efficiency by minimizing parasitic absorption in the short-wavelength region. By optimizing the combination of ZMO buffer and the microgrid/TCO hybrid electrode, a device efficiency of up to 20.5% (with antireflection layers) is achieved over a small device area of 5 mm × 5 mm (total area). Moreover, CIGS solar cells with an increased device area of up to 20 mm × 70 mm (total area) exhibit an efficiency of up to 19.7% (with antireflection layers) when a microgrid/TCO hybrid electrode is applied. Thus, this study demonstrates the potential for high-efficiency, large-area CIGS solar cells with novel microgrid electrodes.

3-aminopropyltriethoxysilane modified MXene on three-dimensional nonwoven fiber substrates for low-cost, stable, and efficient solar-driven interfacial evaporation desalination

Recently, the solar-driven interfacial evaporation desalination has attracted more and more attentions due to the advantages of low cost, zero energy consumption, and high water purification rate, etc. One of the bottlenecks of this emerging technique lies in a lack of simple and low-cost ways to construct three-dimensional (3D) hierarchical microstructures for photothermal membranes. To this end, a two-step strategy is carried out by combining surface functionalization with substrate engineering. Firstly, a silane coupling agent 3-aminopropyltriethoxysilane (APTES) is grafted onto an ideal photothermal material of Ti3C2Tx MXene, to improve the nanochannel sizes and hydrophilicity, which are attributed to enlarged interspaces of MXene and introduced hydrophilic group e.g., –NH2 and –OH, respectively. Secondly, a low-cost and robust nonwoven fiber (NWF) substrate, which has a 3D micron-sized mesh structure with interlaced fiber stacks, is employed as the skeleton to load enough APTES-grafted MXene by a simple soaking method. Benefited from above design, the Ti3C2Tx-APTES/NWF composite membrane with a 3D hierarchical structure shows enhanced light scattering and utilization, water transport and vapor escape. A remarkable evaporation rate of 1.457 kg m−2 h−1 and an evaporation efficiency of 91.48 % are attained for a large-area (5 × 5 cm2) evaporator, and the evaporation rate is further increased to 1.672 kg m−2 h−1 for a small-area (2 × 2 cm2) device. The rejection rates of salt ions and heavy metal ions are higher than 99 % and 99.99 %, respectively, and the removal rates of organic dye molecules are nearly to 100 %. Besides, the composite photothermal membrane exhibits great stabilities in harsh conditions such as high salinities, long cycling, large light intensities, strong acid/alkali environments, and mechanical bending. Most importantly, the photothermal membrane shows a considerable cost-effectiveness of 89.4 g h−1/$. Hence, this study might promote the commercialization of solar-driven interfacial evaporation desalination by collaboratively considering surface modification and substrate engineering for MXene.

Correlating Aggregation Ability of Polymer Donors with Film Formation Kinetics for Organic Solar Cells with Improved Efficiency and Processability.

Film formation kinetics significantly impact molecular processability and power conversion efficiency (PCE) of organic solar cells. Here, two ternary random copolymerization polymers are reported, D18─N-p and D18─N-m, to modulate the aggregation ability of D18 by introducing trifluoromethyl-substituted pyridine unit at para- and meta-positions, respectively. The introduction of pyridine unit significantly reduces material aggregation ability and adjusts the interactions with acceptor L8-BO, thereby leading to largely changed film formation kinetics with earlier phase separation and longer film formation times, which enlarge fiber sizes in blend films and improve carrier generation and transport. As a result, D18─N-p with moderate aggregation ability delivers a high PCE of 18.82% with L8-BO, which is further improved to 19.45% via interface engineering. Despite the slightly inferior small area device performances, D18─N-m shows improved solubility, which inspires to adjust the ratio of meta-trifluoromethyl pyridine carefully and obtain a polymer donor D18─N-m-10 with good solubility in nonhalogenated solvent o-xylene. High PCEs of 13.07% and 12.43% in 1 cm2 device and 43 cm2 module fabricated with slot-die coating method are achieved based on D18─N-m-10:L8-BO blends. This work emphasizes film formation kinetics optimization in device fabrication via aggregation ability modulation of polymer donors for efficient devices.

Highly Efficient and Scalable p-i-n Perovskite Solar Cells Enabled by Poly-metallocene Interfaces.

Inverted p-i-n perovskite solar cells (PSCs) are easy to process but need improved interface characteristics with reduced energy loss to prevent efficiency drops when increasing the active photovoltaic area. Here, we report a series of poly ferrocenyl molecules that can modulate the perovskite surface enabling the construction of small- and large-area PSCs. We found that the perovskite-ferrocenyl interaction forms a hybrid complex with enhanced surface coordination strength and activated electronic states, leading to lower interfacial nonradiative recombination and charge transport resistance losses. The resulting PSCs achieve an enhanced efficiency of up to 26.08% for small-area devices and 24.51% for large-area devices (1.0208 cm2). Moreover, the large-area PSCs maintain >92% of the initial efficiency after 2000 h of continuous operation at the maximum power point under 1-sun illumination and 65 °C.

Enhancing Efficiency of Large-Area Wide-Bandgap Perovskite Solar Modules with Spontaneously Formed Self-Assembled Monolayer Interfaces.

Wide-bandgap (WBG) perovskites play a crucial role in perovskite-based tandem cells. Despite recent advances using self-assembled monolayers (SAMs) to facilitate efficiency breakthroughs, achieving precise control over the deposition of such ultrathin layers remains a significant challenge for large-scale fabrication of WBG perovskite and, consequently, for the tandem modules. To address these challenges, we propose a facile method that integrates MeO-2PACz and Me-4PACz in optimal proportions (Mixed SAMs) into the perovskite precursor solution, enabling the simultaneous codeposition of WBG perovskite and SAMs. This technique promotes the spontaneous formation of charge-selective contacts while reducing defect densities by coordinating phosphonic acid groups with the unbonded Pb2+ ions at the bottom interface. The resulting WBG perovskite solar cells (PSCs) demonstrated a power conversion efficiency of 19.31% for small-area devices (0.0585 cm2) and 17.63% for large-area modules (19.34 cm2), highlighting the potential of this codeposition strategy for fabricating high-performance, large-area WBG PSCs with enhanced reproducibility. These findings offer valuable insights for advancing WBG PSCs and the scalable fabrication of modules.

Breakdown up to 13.5 kV in NiO/β-Ga2O3 Vertical Heterojunction Rectifiers

Vertical heterojunction NiO/β n-Ga2O/n+ Ga2O3 rectifiers with 100 μm diameter fabricated on ∼17–18 μm thick drift layers with carrier concentration 8.8 × 1015 cm−3 and employing simple dual-layer PECVD SiNx/SiO2 edge termination demonstrate breakdown voltages (VB) up to 13.5 kV, on-voltage (VON) of ∼2.2 V and on-state resistance RON of 11.1–12 mΩ.cm2. Without edge termination, the maximum VB was 7.9 kV. The average critical breakdown field in heterojunctions was ∼7.4–9.4 MV. cm−1, within the reported theoretical value range from 8–15 MV.cm−1 for β-Ga2O3. For large area (1 mm diameter) heterojunction deives, the maximum VB was 7.2 kV with optimized edge termination and 3.9 kV without edge termination. The associated maximum power figure-of-merit, VB 2/RON is 15.2 GW·cm−2 for small area devices and 0.65 GW.cm−2 for large area devices. By sharp contrast, small area Schottky rectifiers concurrently fabricated on the same drift layers had maximum VB of 3.6 kV with edge termination and 2.7 kV without edge termination, but lower VON of 0.71–0.75 V. The average critical breakdown field in these devices was in the range 1.9–2.7 MV. cm−1, showing the importance of both the heterojunction and edge termination. Transmission electron microscopy showed an absence of lattice damage between the PECVD and sputtered films within the device and the underlying epitaxial Ga2O3. The key advances are thicker, lower doped drift layers and optimization of edge termination design and deposition processes.

A Comprehensive Review on Defects-Induced Voltage Losses and Strategies toward Highly Efficient and Stable Perovskite Solar Cells

The power conversion efficiency (PCE) of single-junction perovskite solar cells (PSCs) has reached 26.1% in small-scale devices. However, defects at the bulk, surface, grain boundaries, and interfaces act as non-radiative recombination centers for photogenerated electron-hole pairs, limiting the open-circuit voltage and PCE below the Shockley–Queisser limit. These defect states also induce ion migration towards interfaces and contribute to intrinsic instability in PSCs, reducing the quasi-Fermi level splitting and causing anomalous hysteresis in the device. The influence of defects becomes more prominent in large-area devices, demonstrating much lower PCE than the lab-scale devices. Therefore, commercializing PSCs faces a big challenge in terms of rapid decline in working performance due to these intrinsic structural defects. This paper provides a comprehensive review of recent advances in understanding the nature and the classification of defects, their impact on voltage losses, device parameters, intrinsic stability, and defect quantification and characterization techniques. Novel defect passivation techniques such as compositional engineering, additive engineering, post-treatments, dimensionality engineering, and interlayer engineering are also reviewed, along with the improvements in PCE and stability based on these techniques for both small-area devices and large-area roll-to-roll coated devices.

High-Performance All-Small-Molecule Organic Solar Cells Fabricated via Halogen-Free Preparation Process.

Small-molecule organic photovoltaic materials attract more attention attributing to their precisely defined structure, ease of synthesis, and reduced batch-to-batch variations. The majority of all-small-molecule organic solar cells (ASM-OSCs) have traditionally relied on halogenated solvents for dissolving photovoltaic materials as well as used for the additives or solvent vapor annealing. However, these halogen-based processes pose risks to the environment and human health, potentially impeding future commercial production. Herein, we conducted an investigation into the impact of various nonhalogen solvents on the performance of the devices. By selecting the high boiling point solvent toluene, we achieved a desirable phase separation and stable morphology characterized by fibrous crystals within the blend film. Consequently, the power conversion efficiencies of 14.4 and 11.7% were obtained from H31:Y6-based small-area (0.04 cm2) and large-area (1 cm2) devices with steady performance, respectively. This study successfully demonstrated the fabrication of ASM-OSCs without employing halogenated solvent processes, thus offering promising prospects for the commercial production of ASM-OSCs.

Nucleation Regulation and Mesoscopic Dielectric Screening in α-FAPbI3.

While significant advancements in power conversion efficiencies (PCEs) of α-FAPbI3perovskite solar cells (PSCs) have been made, attaining controllable perovskite crystallization is still a considerable hurdle. This challenge stems from the initial formation of δ-FAPbI3, a more energetically stable phase than the desired black α-phase, during film deposition. This disrupts the heterogeneous nucleation of α-FAPbI3, causing the formation of mixed phases and defects. To this end, polarity engineering using molecular additives, specifically ((methyl-sulfonyl)phenyl)ethylamines (MSPEs) are introduced. The findings reveal that the interaction of PbI2-MSPEs-FAI intermediates is enhanced with the increased polarity of MSPEs, which in turn expedites the nucleation of α-FAPbI3. This leads to the development of high-quality α-FAPbI3 films, characterized by vertical crystal orientation and reduced residual stresses. Additionally, the increased dipole moment of MSPE at perovskite grain boundaries attenuates Coulomb attractions among charged defects and screens carrier capture process, thereby diminishing non-radiative recombination. Utilizing these mechanisms, PSCs treated with highly polar 2-(4-MSPE) achieve an impressive PCE of 25.2% in small-area devices and 20.5% in large-area perovskite solar modules (PSMs) with an active area of 70 cm2. These results demonstrate the effectiveness of this strategy in achieving controllable crystallization of α-FAPbI3, paving the way for scalable-production of high-efficiency PSMs.

Playdough-like carbon electrode: A promising strategy for high efficiency perovskite solar cells and modules

Carbon-based perovskite solar cells (C-PSCs) are promising candidates for large-scale photovoltaic applications due to their theoretical low cost and high stability. However, the fabrication of high-performance C-PSCs with large-area electrodes remains challenging. In this work, we propose a novel playdough-like graphite putty as top electrode in the perovskite devices. This electrode with soft nature can form good contact with the hole-transporting layer and the conductive substrate at room temperature by a simple pressing technique, which facilitates the fabrication of both small-area devices and perovskite solar modules. In this preliminary research, the corresponding small devices and modules can achieve efficiencies of 20.29% (∼0.15 ​cm2) and 16.01% (∼10 ​cm2), respectively. Moreover, we analyze the limitations of the optical and electrical properties of this playdough-like graphite electrode on the device performance, suggesting a direction for further improvement of C-PSCs in the future.

Enhancing efficiency and stability of perovskite solar cells through two-step deposition method with the addition of cesium halides to PbI2 precursor

Perovskite films with few defects play a key role in preparing high-performance perovskite solar cells (PSCs). Here, cesium halides, such as CsCl, CsBr, and CsI, were introduced as a modulator into 1st perovskite precursor for manipulating the crystallization of perovskite films. By introducing CsI dense homogeneous perovskite films with high crystallinity, preferential orientation, and a pure black perovskite phase were prepared. In addition, the carrier lifetime of perovskite films was significantly increased because of the suppressed nonradiative recombination. Correspondingly, the power conversion efficiency (PCE) of small-area devices using CsI regulation was increased from 17.45 to 20.29%. Furthermore, the device showed excellent stability maintaining 80% of its initial PCE after 350 h of continuous irradiation. This study demonstrates that CsI-added is a reliable way to prepare PSCs for practical applications.

Terminally Chlorinated and Thiophene-linked Acceptor-Donor-Acceptor Structured 3D Acceptors with Versatile Processability for High-efficiency Organic Solar Cells.

To exploit the potential of our newly developed three-dimensional (3D) dimerized acceptors, a series of chlorinated 3D acceptors (namely CH8-3/4/5) were reported by precisely tuning the position of chlorine (Cl) atom. The introduction of Cl atom in central unit affects the molecular conformation. Whereas, by replacing fluorinated terminal groups (CH8-3) with chlorinated terminal groups (CH8-4 and CH8-5), the red-shift absorption and enhanced crystallization are achieved. Benefiting from these, all devices received promising power conversion efficiencies (PCEs) over 16 % as well as decent thermal/photo-stabilities. Among them, PM6:CH8-4 based device yielded a best PCE of 17.58 %. Besides, the 3D merits with multi alkyl chains enable their versatile processability during the device preparation. Impressive PCEs of 17.27 % and 16.23 % could be achieved for non-halogen solvent processable devices prepared in glovebox and ambient, respectively. 2.88 cm2 modules also obtained PCEs over 13 % via spin-coating and blade-coating methods, respectively. These results are among the best performance of dimerized acceptors. The decent performance of CH8-4 on small-area devices, modules and non-halogen solvent-processed devices highlights the versatile processing capability of our 3D acceptors, as well as their potential applications in the future.

Organic Solar Cells with Nanofibers in the Active Layer Obtained by Coaxial Electrospinning

The high demand for energy and the intensification of climate change have led to the need to improve renewable energy sources, such as solar energy. Organic bulk heterojunction (BHJ) cells using conjugated polymers as the electron donor in the active layer are an alternative because they are easy processability, flexible, have the absorption spectrum corresponding to the structure of the polymer, and can be synthesized in an endless variety of chemical structures. One of the limiting factors for large-scale applications was the relatively low conversion of solar energy into electricity, but this has been practically overcome recently, as efficiencies of around 20% have been achieved for small-area devices and around 16% for larger devices, approaching conventional silicon cells. The device’s stability remains the most restraining factor, as it has to last at least ten years in sun and weather exposure. This review presents works that improve the efficiency of photovoltaic devices by addressing the development of materials used in the active layer (semiconductor polymers and acceptor materials). Additionally, the use of nanofibers in the active layer obtained by the electrospinning technique is discussed. The nanofiber quality parameters (solute properties, solution properties, processing conditions, and environmental conditions) are discussed, including coaxial electrospinning.

Low-photovoltage-loss pringting perovskite solar cells in ambient air through ink synergistic engineering

The uncontrollable large-scare preparation of perovskite in air is currently hindering its photovoltaic industrialization. The internal relationship between the regulation of ink components and the film forming mechanism of perovskite during large-scare preparation is a crucial factor for device performance. Herein, MAAc ionic liquid and Biuret were introduced as the solvent and additive of ink, respectively. Both MAAc and Biuret can independently influence the crystallization process of perovskite and this ink synergistic engineering can accurately regulate the crystallization process and improve the quality of bar-coated perovskite films at reduced process temperatures. We achieved the highest efficiency of 20.62% on a small-area device with improved stability, and an efficiency of 16.51% on a micro-module with an area of 14.8 cm2. This ink synergistic engineering with low temperature preparation process is expected to promote the industrialization of perovskite solar cells. In addition, our research on the crystallization process provides guidance for the development of novel coating and printing techniques for perovskite materials.

Extending the π-Conjugated System in Spiro-Type Hole Transport Material Enhances the Efficiency and Stability of Perovskite Solar Modules.

Hole transport materials (HTMs) are a key component of perovskite solar cells (PSCs). The small molecular 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenyl)-amine-9,9'-spirobifluorene (spiro-OMeTAD, termed "Spiro") is the most successful HTM used in PSCs, but its versatility is imperfect. To improve its performance, we developed a novel spiro-type HTM (termed "DP") by substituting four anisole units on Spiro with 4-methoxybiphenyl moieties. By extending the π-conjugation of Spiro in this way, the HOMO level of the HTM matches well with the perovskite valence band, enhancing hole mobility and increasing the glass transition temperature. DP-based PSC achieves high power conversion efficiencies (PCEs) of 25.24 % for small-area (0.06 cm2 ) devices and 21.86 % for modules (designated area of 27.56 cm2 ), along with the certified efficiency of 21.78 % on a designated area of 27.86 cm2 . The encapsulated DP-based devices maintain 95.1 % of the initial performance under ISOS-L-1 conditions after 2560 hours and 87 % at the ISOS-L-3 conditions over 600 hours.