Single Solid-phase Extraction Research Articles

Determination and risk assessment of UV filters and benzotriazole UV stabilizers in wastewater from a wastewater treatment plant in Lüneburg, Germany.

UV filters and benzotriazole UV stabilizers are considered emerging contaminants in the environment. LC-MS/MS and GC-MS methods, involving a single solid phase extraction protocol, were developed and validated to determine eight UV filters and seven UV stabilizers, respectively in wastewater from a wastewater treatment plant (WWTP) in Lüneburg, Germany. The LC-MS/MS method exhibited extraction recoveries of ≥ 71% at six different fortification levels with limits of detection (LODs) range of 0.02ngmL-1 - 0.09ngmL-1. Extraction recoveries of 47 to 119% at six different fortification levels were obtained for the GC-MS method with LODs range of 0.01 - 0.09ngmL-1. Among the UV filters, the highest mean concentration was determined for octocrylene (OCR) in influent (3.49ngmL-1) while the highest mean concentration was measured for 2-hydroxy-4-octyloxybenzophenone (UV 531) in influent (0.44ngmL-1) among the UV stabilizers. Potential risk to aquatic organisms was assessed by the risk quotient approach. Only OCR presented a high risk to aquatic invertebrates whereas 2-ethylhexyl 4-methoxycinnamate (EHMC) and 2-ethylhexyl salicylate (EHS) posed high risks to algae. Benzotriazole UV stabilizers presented negligible risks to aquatic invertebrates and fish. This work reports the detection of rarely studied 4-aminobenzoic acid (PABA) and UV 531 in WWTP influent and effluent. The occurrence and risk assessment of target benzotriazole UV stabilizers in wastewater from a German WWTP was demonstrated for the first time.

Enhancing solid-phase extraction of tetracyclines with a hybrid biochar sorbent: A comparative study of chlorella and bamboo biochars

Biochar, a sustainable sorbent derived from pyrolyzed biomass, has garnered attention for its efficacy in solid-phase extraction (SPE) of antibiotics, with a particular focus on tetracyclines (TCs). Despite its recognized potential, the intricate separation mechanisms operative in biochar-based SPE systems have not been fully deciphered. This investigation contrasts chlorella biochar against commercial bamboo biochar, harnessing an array of analytical methodologies-microstructure characterization, adsorption thermodynamics, competitive adsorption kinetics, H+ back titration, and selectivity adsorption studies-complemented by a Box-Behnken design for the optimization of chlorella/bamboo-SPE and subsequent application in the analysis of animal-derived foodstuffs. The study unveils that a hybrid sorbent, integrating nitrogen-doped microporous chlorella biochar with mesoporous bamboo biochar in a 95/5 mass ratio, markedly diminishes irreversible adsorption while enhancing selectivity, surpassing the performance of single biochar SPE systems. The elucidated separation mechanisms implicate a partition model, propelled by oxygen-rich functional groups on chlorella biochar and the rapid adsorption kinetics of bamboo biochar, all orchestrated by electrostatic interactions within the mixed biochar framework. Moreover, the synergy of mixed biochar-SPE with high-performance liquid chromatography (HPLC) demonstrates exceptional proficiency in detecting TCs in animal viscera, evidenced by recovery rates spanning 80.80 % to 106.98 % and RSDs ranging from 0.24 % to 14.69 %. In essence, this research not only sheds light on the multifaceted factors influencing SPE efficiency but also propels the use of biochar towards new horizons in environmental monitoring and food safety assurance.

International Comparison, Risk Assessment, and Prioritisation of 26 Endocrine Disrupting Compounds in Three European River Catchments in the UK, Ireland, and Spain.

Endocrine-disrupting compounds (EDCs) constitute a wide variety of chemistries with diverse properties that may/can pose risks to both humans and the environment. Herein, a total of 26 compounds, including steroids, flame retardants, and plasticizers, were monitored in three major and heavily urbanized river catchments: the R. Liffey (Ireland), the R. Thames (UK), and the R. Ter (Spain), by using a single solid-phase extraction liquid chromatography-mass spectrometry (SPE-LC-MS/MS) method. Occurrence and frequency rates were investigated across all locations over a 10-week period, with the highest concentration obtained for the flame retardant tris(2-chloroethyl) phosphate (TCEP) at 4767 ng∙L-1 in the R. Thames in Central London. Geographical variations were observed between sites and were partially explained using principal component analysis (PCA) and hierarchical cluster analysis (HCA). In particular, discrimination between the R. Ter and the R. Thames was observed based on the presence and concentration of flame retardants, benzotriazole, and steroids. Environmental risk assessment (ERA) across sites showed that caffeine, a chemical marker, and bisphenol A (BPA), a plasticizer, were classified as high-risk for the R. Liffey and R. Thames, based on relative risk quotients (rRQs), and that caffeine was classified as high-risk for the R. Ter, based on RQs. The total risks at each location, namely ΣRQriver, and ΣrRQriver, were: 361, 455, and 723 for the rivers Liffey, Thames, and Ter, respectively. Caffeine, as expected, was ubiquitous in all 3 urban areas, though with the highest RQ observed in the R. Ter. High contributions of BPA were also observed across the three matrices. Therefore, these two compounds should be prioritized independently of location. This study represents a comprehensive EDC monitoring comparison between different European cities based on a single analytical method, which allowed for a geographically independent ERA prioritization to be performed.

Determination of trace organic contaminants by a novel mixed-mode online solid-phase extraction coupled to liquid chromatography–tandem mass spectrometry

In this study, a novel mixed-mode online solid-phase extraction (SPE) method was developed to recover miscellaneous trace organic contaminants (TrOCs) from environmental water samples. Six kinds of sorbents, including C18 substances, hypercross-linked polymers (2), cation-exchange resins, anion-exchange resins, and graphitized nonporous carbons, were packed into a single online SPE cartridge. Furthermore, a fully automated analytic method was established by coupling this mixed-mode online SPE with liquid chromatography tandem mass spectrometry (online SPE-LC-MS/MS). Sixty-nine TrOCs with diverse properties were selected to examine the performance of this mixed-mode SPE cartridge in comparison with solo-mode online SPE cartridges. The method quantification limit (MQL) and the relative recovery coefficient of TrOCs in diverse water matrices, including groundwater, surface water and sewage effluent were evaluated. The MQL of most TrOCs was lower than 10 ng L−1. The relative recovery coefficients for most TrOCs in the groundwater (50/69) and surface water (38/69) matrix fit in the satisfactory range. Moreover, mixed-mode online SPE coupled with LC-high-resolution MS was applied for a suspect screening of TrOCs in sewage effluents. A series of highly polar TrOCs that had scarcely been reported by previous studies were identified by this practical and easily accessible method. Finally, this novel mixed-mode online SPE with LC-MS/MS method was applied to quantify the TrOCs in the environmental water samples.

Optimization of a Multiresidue Analysis of 65 Pesticides in Surface Water Using Solid-Phase Extraction by LC-MS/MS.

An analytical method was developed and validated for simultaneous quantitation of 65 pesticides, including one single solid-phase extraction (SPE) procedure in surface water by liquid chromatography coupled to tandem mass spectroscopy. Different parameters that have an influence on extraction efficiency were evaluated in this research. Different types of cartridges, elution solvents, and sorbent drying time were investigated, and the most appropriate one was selected. Moreover, various pretreatment techniques were applied to remove sediments from water without the loss of pesticides. Centrifugation was introduced as the best option at the beginning of sample preparation to resolve the clogging of the sorbent cartridges. The recoveries of all pesticides ranged from 70% to 120%, with a relative standard deviation of less than 13.7%. The feasibility of the method was evaluated on 10 surface water samples with different concentrations of sand, sediment, and particles.

Changes in dissolved organic matter during water treatment by sequential solid-phase extraction and unknown screening analysis

Isolation of complex dissolved organic matter (DOM) from environmental water is a major challenge for unknown screening analysis by high-resolution mass spectrometry. In this study, DOM in process water during advanced drinking water treatment was fractionated sequentially by three solid-phase extraction (SPE) cartridges based on the polarity and charge of DOM molecules. By sequential SPE with unknown screening analysis, over 3000 DOM features were found in raw water, whereas around 2000 were obtained by a single SPE. The hydrophobic neutral (HPON) fraction contained CHO features with highest averaged molecular weight followed by hydrophobic acid (HPOA) and then hydrophilic acid (HPIA). The average degree of carbon double bond equivalents and carbon oxidation states indicated that the HPON fraction contained molecules that were more unsaturated and less oxidized than those of the HPOA and HPIA fractions. Ozone selectively decomposed (1) more unsaturated and less oxidized HPON features, (2) more unsaturated HPOA compounds, and (3) less oxidized HPIA molecules. Oxidation by-products were mostly HPON and HPIA compounds that were more oxidized than the decomposed molecules. During biological activated carbon (BAC) filtration, less oxidized HPON were preferentially removed, whereas HPOA were removed without selectivity. HPON and HPIA molecules with more oxidized character were found to be refractory to BAC treatment. HPON with more unsaturated and HPIA with more oxidized characters were decomposed by chlorine. Many types of HPIA decomposed during chlorination were the oxidation by-products of ozonation that were refractory to BAC treatment. Sequential SPE with unknown screening analysis provided previously unknown details of the molecular characteristics of DOM and its changes during advanced water treatment.

Determination of trace polycyclic aromatic hydrocarbons in water and milk using solid-phase extraction packed with graphene/chitosan composite aerogel prior to gas chromatography-mass spectrometry.

Polycyclic aromatic hydrocarbons, ubiquitous compounds that result from incomplete combustion or pyrolysis of natural and man-made combustion sources, can adversely affects human health due to their well-known toxicity. This paper demonstrates the significant potential of graphene/chitosan composite aerogels as solid-phase extraction sorbents for efficient polycyclic aromatic hydrocarbon extraction and material for the highly sensitive analysis in environmental samples using gas chromatography-mass spectrometry in selective ion monitoring mode. Under the optimal condition, samples spiked with polycyclic aromatic hydrocarbons were determined at the pg/mL level in different aqueous sample matrices, including tap water, river water, and milk. The results showed that the prepared aerogels have excellent adsorption capability for 16 target analytes. The limits of detection ranged from 1.7 to 8.8 pg/mL. The recoveries of polycyclic aromatic hydrocarbons spiked in river water ranged from 85.9 to 113%, with relative standard deviations of 1.1-6.6%. The sorbent was reused for multiple polycyclic aromatic hydrocarbon extractions using a single solid-phase extraction cartridge in the concentration range of 10-2000 pg/mL. The method provides excellent correlation coefficients over 0.9990. These results indicate the capability of this method to determine trace polycyclic aromatic hydrocarbons in any water matrix.

A novel voltammetric approach to the detection of primary bile acids in serum samples

An innovative voltammetric approach to the detection of cholic and chenodeoxycholic acids is presented. These two primary bile acids are important biomarkers of liver function in humans and are involved in many physiological processes in the human body. Herein we describe a way to reproducibly convert the hard-to-detect bile acid molecule into an easily detectable derivative in situ using 0.1 M HClO4 in acetonitrile (water content 0.55%). Under these conditions the bile acids are dehydrated and the resulting alkenes can be subsequently oxidized electrochemically on polished boron-doped diamond electrode under unchanged conditions at approximately +1.2 V vs. Ag/AgNO3 in acetonitrile. After optimization, differential pulse voltammetry provides competitive limits of detection of 0.5 µM and 1.0 µM for cholic and chenodeoxycholic acid, respectively, with a linear course of calibration dependency to the minimum of 80 µM. The method was applied for detection of cholic and chenodeoxycholic acids in artificial and human serum samples using single solid phase extraction on C-18 cartridge for preliminary separation of the analytes. High recoveries of 80–90% were consistently obtained by the proposed voltammetric method and reference HPLC with fluorescence detection for human serum samples, confirming good selectivity for real-life samples.

Analysis of N-Acy-L-homoserine lactones (AHLs) in wastewater treatment systems using SPE-LLE with LC-MS/MS

The occurrence and distribution of N-acyl homoserine lactones (AHLs) in membrane bioreactors (MBRs) treating wastewater has garnered much attention as they have been shown to play critical role in biofouling. There is a need to develop a single method capable of analysing AHLs in various wastewater with comparable and reliable performance. A novel and robust method was proposed for trace analysis of 11 AHLs in wastewater treatment systems treating domestic and industrial wastewater. This method utilised solid phase extraction (SPE) to extract AHLs from wastewater followed by liquid-liquid extraction (LLE) to extract AHLs from the SPE eluant, and used N-heptanoyl-dl-homoserine lactone (C7-HSL) as an internal standard. There was no need to prepare matrix-matched calibration curve for accurate quantification of AHLs in the liquid chromatography tandem mass chromatography (LC-MS/MS) analysis. The developed method was validated with six different types of domestic and industrial wastewater with regard to AHLs recoveries and matrix effects. For treated domestic and industrial wastewater, the relative recoveries ranged from 75% to 130% and the matrix effects ranged from 89% to 122%. This method exhibited remarkable improvement compared with single SPE. The results also indicated that inclusion of LLE after SPE could effectively alleviate matrix effects, which may be because of the removal of relatively hydrophilic interferences by using dichloromethane to extract AHLs from the SPE eluant composing of methanol and water. The limits of detection of the AHLs were all below 5 ng/L for the tested wastewater samples. The developed method of SPE-LLE with LC-MS/MS was applied to analyse AHLs in four lab-scale and one pilot-scale wastewater treatment systems. Wide spectrum of AHLs with alkanoyl chains ranging from C4 to C14 were detected with concentrations ranging from 2.7 to 299.2 ng/L. This method is capable of identifying and quantifying trace levels of AHLs in various wastewater treatment systems and can help us better understand the mechanisms of AHL-mediated quroum sensing in various wastewater treatment systems.

METHOD DEVELOPMENT AND VALIDATION OF SELECTIVE AND HIGHLY SENSITIVE METHOD FOR DETERMINATION OF APIXABAN IN HUMAN PLASMA USING LIQUID CHROMATOGRAPHY-TANDEM MASS SPECTROMETRY

Objective: The present research work aims to develop and validate a selective and highly sensitive method for the determination of apixaban in human plasma using liquid chromatography-tandem mass spectrometry (LC-MS/MS).
 Methods: 200 µl of sodium heparin plasma samples were acidified and clean-up was performed by using solid-phase extraction (SPE). Apixaban 13C D3 was used as an internal standard (deuterated) to lower the relative matrix effects and a single step SPE was employed for sample clean up. 10 µl of SPE eluent was loaded onto Hypersil Beta Basic C18, 100×4.6 mm, 5 µ column for highly selective chromatographic separation using an isocratic mobile phase. 2 mmol ammonium acetate in water and acetonitrile were delivered by using a quaternary low-pressure gradient pump without premixing at a minimum flow rate of 0.50 ml/min.
 Results: LC-MS/MS method was successfully developed and validated to demonstrate the lowest detection limit of 0.05 ng/ml and a linear dynamic range from 1-250 ng/ml with r2>0.99. Method development and validation results proved that the method is selective and highly sensitive for the determination of apixaban in human plasma using LC-MS/MS.
 Conclusion: Current method can be applied for both therapeutic drug monitoring (TDM) and pharmacokinetic (PK) study analysis.

Extraction, isolation and purification of tetrahydrocannabinol from the Cannabis sativa L. plant using supercritical fluid extraction and solid phase extraction

The tetrahydrocannabinol (THC) was obtained from Cannabis sativa L. plant material using supercritical fluid extraction (SFE) and solid phase extraction (SPE). SFE was utilized at different pressures (15–33 MPa), temperatures (40–80 °C) and ethanol (EtOH) as co-solvent (0–5%). The effect of extraction parameters on response variables (yield and THC content in raw extract) was evaluated. Keeping both temperature and co-solvent concentration constant at 60 °C and 2% respectively, the highest THC content in raw extracts reaches 37.85% at 33 MPa and 36.18% at 15 MPa. One extract with high THC content was selected and submitted for purification-isolation by SPE. One final fraction with a 90.1% of THC was obtained using a single SPE step. This fraction was analyzed by GC, RP-HPLC and NMR to verify the THC purity. A sequential SFE-SPE process allows to obtain high purity THC from the cannabis plant, which is suitable as quality control material or analytical standard.

Sensitive and Selective Amino Acid Profiling of Minute Tissue Amounts by HPLC/Electrospray Negative Tandem Mass Spectrometry Using 9-Fluorenylmethoxycarbonyl (Fmoc-Cl) Derivatization.

A method for selective and sensitive quantification of amino acids is described. The combination of established derivatization procedures of secondary and primary amino groups with 9-fluorenylmethoxycarbonyl chloride (Fmoc-Cl) and subsequent detection of derivatized amino acids by LC-ESI-MS/MS using multiple reaction monitoring provides high selectivity. The attachment of an apolar moiety enables purification of derivatized amino acids from matrix by a single solid-phase extraction step, which increases sensitivity by reduced ion suppression during LC-ESI-MS/MS detection. Additionally, chromatography of all amino acids can be performed on reversed-phase HPLC columns using eluents without additives, which are known to cause significant decreases in signal to noise ratios. The method has been routinely applied for amino acid profiling of low amounts of liquids and tissues of various origins with a sample throughput of about 50-100 samples a day. In addition to a detailed description of the method, some representative examples are presented.

Solid-phase extraction, quantification, and selective determination of microcystins in water with a gold-polypyrrole nanocomposite sorbent material

A novel sorbent material, gold-polypyrrole (Au-PPy) nanocomposite-coated silica, is described for the efficient solid-phase extraction (SPE) of six common microcystins (MCs) well below the recommended United States EPA and World Health Organization (WHO) guidelines. With the optimized SPE protocol, samples spiked with MCs were determined at ng/L concentrations by liquid chromatography-mass spectrometry (LC–MS) in different aqueous sample matrices, including HPLC-grade, tap, and lake water. The average recoveries for all MCs tested in the three water matrices ranged from 94.1–103.2% with relative standard deviations (RSDs) of 1.6–5.4%, which indicated excellent extraction efficiency and reproducibility. Limits of detection (LODs) and limits of quantification (LOQs) for all MCs in both tap and lake water samples were determined to be ≤1.5 ng/L and 5.0 ng/L, respectively. The Au-PPy nanocomposite-coated sorbent material was reusable for at least three independent MC extractions with a single SPE cartridge in the concentration range of 10–500 ng/L. Importantly, off-column selective separation at the sample preparation and preconcentration stage between more hydrophilic and more hydrophobic MCs was achieved by sequential elution through changes in the solvent composition and SPE bed size. Therefore, the Au-PPy nanocomposite-coated silica sorbent is a promising new material for the quantification of MC variants in water samples.

Ionic Liquid‐Based Liquid–Liquid Microextraction for Benzodiazepine Analysis in Postmortem Blood Samples

Sample preparation is rapidly improving to fulfill the need for faster and more environmentally friendly alternatives. In this respect, ionic liquid-based dispersive liquid-liquid microextraction (IL-DLLME) is an interesting technique. However, it has not yet been evaluated for the analysis of postmortem samples, which are frequently analyzed in forensic toxicology. This study investigates the applicability of IL-DLLME coupled to liquid chromatography-tandem mass spectrometry (LC-MS/MS), for the analysis of benzodiazepines in postmortem blood of 11 forensic cases. The method was compared with a validated solid-phase extraction (SPE) method. Bland-Altman analysis was performed on 24 benzodiazepine measurements. Both methods gave comparable results, except for flurazepam and temazepam (>55% difference). A feasible explanation is high postmortem matrix variability that was not considered during IL-DLLME validation experiments. Another issue could be the use of a single nondeuterated SPE internal standard. Overall, IL-DLLME has proven its usability for the analysis of postmortem blood.

Integrated electrokinetically driven microfluidic devices with pH-mediated solid-phase extraction coupled to microchip electrophoresis for preterm birth biomarkers.

Integration in microfluidics is important for achieving automation. Sample preconcentration integrated with separation in a microfluidic setup can have a substantial impact on rapid analysis of low-abundance disease biomarkers. Here, we have developed a microfluidic device that uses pH-mediated solid-phase extraction (SPE) for the enrichment and elution of preterm birth (PTB) biomarkers. Furthermore, this SPE module was integrated with microchip electrophoresis for combined enrichment and separation of multiple analytes, including a PTB peptide biomarker (P1). A reversed-phase octyl methacrylate monolith was polymerized as the SPE medium in polyethylene glycol diacrylate modified cyclic olefin copolymer microfluidic channels. Eluent for pH-mediated SPE of PTB biomarkers on the monolith was optimized using different pH values and ionic concentrations. Nearly 50-fold enrichment was observed in single channel SPE devices for a low nanomolar solution of P1, with great elution time reproducibility (<7% RSD). The monolith binding capacity was determined to be 400 pg (0.2 pmol). A mixture of a model peptide (FA) and a PTB biomarker (P1) was extracted, eluted, injected, and then separated by microchip electrophoresis in our integrated device with ∼15-fold enrichment. This device shows important progress towards an integrated electrokinetically operated platform for preconcentration and separation of biomarkers.

Two-dimensional solid-phase extraction strategy for the selective enrichment of aminoglycosides in milk.

An orthogonal two-dimensional solid-phase extraction strategy was established for the selective enrichment of three aminoglycosides including spectinomycin, streptomycin, and dihydrostreptomycin in milk. A reversed-phase liquid chromatography material (C18 ) and a weak cation-exchange material (TGA) were integrated in a single solid-phase extraction cartridge. The feasibility of two-dimensional clean-up procedure that experienced two-step adsorption, two-step rinsing, and two-step elution was systematically investigated. Based on the orthogonality of reversed-phase and weak cation-exchange procedures, the two-dimensional solid-phase extraction strategy could minimize the interference from the hydrophobic matrix existing in traditional reversed-phase solid-phase extraction. In addition, high ionic strength in the extracts could be effectively removed before the second dimension of weak cation-exchange solid-phase extraction. Combined with liquid chromatography and tandem mass spectrometry, the optimized procedure was validated according to the European Union Commission directive 2002/657/EC. A good performance was achieved in terms of linearity, recovery, precision, decision limit, and detection capability in milk. Finally, the optimized two-dimensional clean-up procedure incorporated with liquid chromatography and tandem mass spectrometry was successfully applied to the rapid monitoring of aminoglycoside residues in milk.

Sequence‐Defined Oligomers from Hydroxyproline Building Blocks for Parallel Synthesis Applications

The functionality of natural biopolymers has inspired significant effort to develop sequence-defined synthetic polymers for applications including molecular recognition, self-assembly, and catalysis. Conjugation of synthetic materials to biomacromolecules has played an increasingly important role in drug delivery and biomaterials. We developed a controlled synthesis of novel oligomers from hydroxyproline-based building blocks and conjugated these materials to siRNA. Hydroxyproline-based monomers enable the incorporation of broad structural diversity into defined polymer chains. Using a perfluorocarbon purification handle, we were able to purify diverse oligomers through a single solid-phase extraction method. The efficiency of synthesis was demonstrated by building 14 unique trimers and 4 hexamers from 6 diverse building blocks. We then adapted this method to the parallel synthesis of hundreds of materials in 96-well plates. This strategy provides a platform for the screening of libraries of modified biomolecules.

High-throughput quantification of more than 100 primary- and secondary-metabolites, and phytohormones by a single solid-phase extraction based sample preparation with analysis by UHPLC-HESI-MS/MS.

BackgroundPlant metabolites are commonly functionally classified, as defense- or growth-related phytohormones, primary and specialized metabolites, and so forth. Analytical procedures for the quantifications of these metabolites are challenging because the metabolites can vary over several orders of magnitude in concentrations in the same tissues and have very different chemical characteristics. Plants clearly adjust their metabolism to respond to their prevailing circumstances in very sophisticated ways that blur the boundaries among these functional or chemically defined classifications. But if plant biologists want to better understand the processes that are important for a plant’s adaptation to its environment, procedures are needed that can provide simultaneous quantifications of the large range of metabolites that have the potential to play central roles in these adjustments in a cost and time effective way and with a low sample consumption.ResultsHere we present a method that combines well-established methods for the targeted analysis of phytohormones, including jasmonates, salicylic acid, abscisic acid, gibberellins, auxins and cytokinins, and extends it to the analysis of inducible and constitutive defense compounds, as well as the primary metabolites involved in the biosynthesis of specialized metabolites and responsible for nutritional quality (e.g., sugars and amino acids). The method is based on a single extraction of 10–100 mg of tissue and allows a broad quantitative screening of metabolites optimized by their chemical characteristics and concentrations, thereby providing a high throughput analysis unbiased by the putative functional attributes of the metabolites. The tissues of Nicotiana attenuata which accumulate high levels of nicotine and diterpene glycosides, provide a challenging matrix that thwarts quantitative analysis; the analysis of various tissues of this plant are used to illustrate the robustness of the procedure.ConclusionsThe method described has the potential to unravel various, until now overlooked interactions among different sectors of plant metabolism in a high throughput manner. Additionally, the method could be particularly beneficial as screening method in forward genetic approaches, as well as for the investigation of plants from natural populations that likely differ in metabolic traits.Electronic supplementary materialThe online version of this article (doi:10.1186/s13007-016-0130-x) contains supplementary material, which is available to authorized users.

A novel, simultaneous extraction of FAEE and EtG from meconium and analysis by LC-MS/MS.

Fatty acid ethyl esters (FAEEs) and ethyl-glucuronide (EtG) in meconium have been widely studied as biomarkers of maternal alcohol consumption during pregnancy. Many analytical approaches have been proposed for their analysis, mostly consisting of separated extraction procedures requiring the use of two meconium aliquots. This study aimed to validate a new analytical procedure for the simultaneous extraction of FAEEs and EtG from a meconium aliquot through a single solid-phase extraction (SPE) applied to 242 anonymized samples of meconium. Targeted FAEEs were: ethyl-myristate (Myr), ethyl-palmitate (Pal), ethyl-oleate (Ole) and ethyl-stearate (Ste). Two hundred milligrams of meconium was sonicated with acetonitrile, and a single SPE performed by means of aminopropyl columns. FAEEs were eluted with hexane, followed by EtG elution with water. Both the mixtures were dried, recovered, and analyzed by liquid chromatography-tandem mass spectrometry using C8 (FAEEs) and C18 (EtG) columns. Transitions were: m/z 257 → 57,88, Myr; m/z 262 → 57,88, Myr-d5; m/z 285 → 57, 72, Pal; m/z 290 → 57,258, Pal-d5; m/z 311 → 72,114, Ole; m/z 316 → 72,265, Ole-d5; m/z 257 → 57,72 Ste; m/z 318 → 57,286, Ste-d5; m/z 221 → 75,85, EtG; m/z 226 → 75,85, EtG-d5. Lower limit of quantification range was 10-15ng/g for FAEEs and 10ng/g for EtG. Linearity was evaluated for different concentration ranges; the mean coefficients of determination (R (2)) were above 0.9961. Precision and accuracy for FAEEs and EtG were consistently ≤20% and ±20%, respectively. Ion suppression was observed for all the analytes. Matrix effect did not significantly affect the analyses. Recovery efficiency was 93% for EtG and 75-85% for FAEEs.

Bioanalytical LC-MS Method for the Quantification of Plasma Androgens and Androgen Glucuronides in Breast Cancer.

The physiological and pathological development of the breast is strongly affected by the hormonal milieu consisting of steroid hormones. Mass spectrometry (MS) technologies of high sensitivity and specificity enable the quantification of androgens and consequently the characterization of the hormonal status. The aim of this study is the assessment of plasma androgens and androgen glucuronides, in the par excellence hormone-sensitive tissue of the breast, through the application of liquid chromatography-mass spectrometry (LC-MS). A simple and efficient fit-for-purpose method for the simultaneous identification and quantification of dehydroepiandrosterone sulfate (DHEAS), androstenedione (A4), androsterone glucuronide (ADTG) and androstane-3α, 17β-diol-17-glucuronide (3α-diol-17G) in human plasma was developed and validated. The presented method permits omission of derivatization, requires a single solid-phase extraction procedure and the chromatographic separation can be achieved on a single C18 analytical column, for all four analytes. The validated method was successfully applied for the analysis of 191 human plasma samples from postmenopausal women with benign breast disease (BBD), lobular neoplasia (LN), ductal carcinoma in situ and invasive ductal carcinoma (IDC). DHEAS plasma levels exhibited significant differences between LN, IDC and BBD patients (P < 0.05). Additionally, ADTG levels were significantly higher in patients with LN compared with those with BBD (P < 0.05).