Single-phase Stand-alone Inverter Research Articles

Design of PFC converter with stand-alone inverter for microgrid applications

The proposed topology is used to connect a single-phase and a three-phase renewable energy resources to the grid. The single-phase source is coupled to a single-phase PFC boost converter, which enhances the input PF utilizing two feedback loops: outer voltage loop control and inner current loop control. The basic hightlight is to study the PFC converter in microgrid application where renewables are integrated with the systems. The basic aim is to observe the overall performance of the converters with various disturbances such as load variations, etc. Here, the single-phase and three-phase stand-alone inverter is used to get the the output of the PFC boost converters. A symmetrical sinusoidal output voltage waveform should be produced and maintained by the inverter. The three-phase source is also coupled to a PFC buck converter, which enhances the input PF utilizing two feedback loops: outer voltage loop control and inner current loop control. The single-phase stand-alone inverter receives the output of the PFC buck converter. The transformer receives the outputs of both the inverters as it is a multi-winding high-frequency transformer and offers isolation between the grid and the source. The pulses for the switches in the single-phase inverter coupled stand-alone system were generated using a sinusoidal pulse width modulation approach. Both the PI controllers are implemented to maintain the regulations. The simulation results are achieved by varying the load, maintaining a constant voltage, and observing whether the current varies as the load changes. It also provides the efficacy of the study.

Unbalanced synchronous reference frame control of singe-phase stand-alone inverter

This paper presents harmonic damping schemes of the single-phase stand-alone inverter. The unbalanced synchronous reference frame technique is selected to control fundamental frequency voltage at the point of common coupling. The output voltage and the inductor current of the inverter are transformed to the unbalanced synchronous reference frame in which the proportional-integral regulators are used to force the error signals in the dq axes to zero. This control scheme does not require an orthogonal signal generator, and it is equivalent to the ideal proportional-resonant regulator. Harmonic regulators, orders 3rd, 5th, 7th, and 9th are added to minimize the voltage harmonics caused by the connected nonlinear load. The proposed controller is compared with the commonly-used multi-resonant controller. Simulation and experimental results of a 1.5-kVA inverter with the proposed control scheme exhibited excellent harmonic damping of the output voltage, caused by a highly nonlinear load and fast transient performance, which were better than the conventional resonant controller.

Load Disturbance Compensation for Stand-alone Inverters Using an Inductor Current Observer

A control scheme for stand-alone inverters that utilizes an inductor current observer (ICO) is proposed. The proposed method measures disturbance load currents using a current sensor and it estimates the inductor current using the ICO. The filter parameter mismatch effect is analyzed to confirm the ICO’s controllability. The ICO and controllers are designed in a continuous-time domain and transferred to a discrete-time domain with a digital delay. Experimental results demonstrate the effectiveness of the ICO using a 5-kVA single-phase stand-alone inverter prototype. The experimental results demonstrate that the observed current matches the actual current and that the proposed method can archive a less than 2.4% total harmonic distortion (THD) sinusoidal output waveform under nonlinear load conditions.

Application of the harmonic control arrays technique to single‐phase stand‐alone inverters

This study proposes the adaption of the harmonic control array (HCA) technique to control a single-phase stand-alone inverter system. The HCA method is recently proposed as an efficient scheme to control the systems with periodic references or disturbances. The HCA appropriately adjusts the harmonic components of the control signal to obtain a zero steady-state error. Since the signals and parameters involved in this method are complex valued, a discrete time implementation is presented for applying the method through a digital platform. The design procedure of the controller parameters are also presented by details. To confirm the theoretical achievements, experimental results for the prototype system are presented in this study. The results demonstrate the effectiveness of the proposed control scheme.

Modelling a Stand-Alone Inverter and Comparing the Power Quality of the National Grid with Off-Grid System

Developments in power electronics have enabled the widespread application of Pulse Width Modulation (PWM) inverters, notably for connecting renewable systems to the grid. This study demonstrates that a high-quality power can be achieved using a stand-alone inverter, whereby the comparison between the power quality of the stand-alone inverter with battery storage (off-grid) and the power quality of the utility network is presented. Multi-loop control techniques for a single phase stand-alone inverter are used. A capacitor current control is used to give active damping and enhance the transient and steady state inverter performance. A capacitor current control is cheaper than the inductor current control, where a small current sensing resistor is used. The output voltage control is used to improve the system performance and also control the output voltage. The inner control loop uses a proportional gain current controller and the outer loop is implemented using internal model control proportional-integral-derivative to ensure stability. The optimal controls are achieved by using the Sisotool tool in MATLAB/Simulink. The outcome of the control scheme of the numerical model of the stand-alone inverter has a smooth and good dynamic performance, but also a strong robustness to load variations. The numerical model of the stand-alone inverter and its power quality are presented, and the power quality is shown to meet the IEEE 519-2014. Furthermore, the power quality of the off-grid system is measured experimentally and compared with the grid power, showing power quality of off-grid system to be better than that of the utility network.

High-Performance Voltage Controller Design Based on Capacitor Current Control Model for Stand-alone Inverters

This study proposes high-performance voltage controller design that employs a capacitor current control model for single-phase stand-alone inverters. The single-phase stand-alone inverter is analyzed via modeling, which is then used to design the controller. A design methodology is proposed to maximize the bandwidth of the feedback controller. Subsequently, to compensate for the problems caused by the bandwidth limitations of the controller, an error transfer function that includes the feedback controller is derived, and the stability of the repetitive control scheme is evaluated using the error transfer function. The digital repetitive controller is then implemented. The simulation and experimental results show that the performance of the proposed controller is high in a 1.5 kW singlephase stand-alone inverter prototype.