Multiple-input Single-output Research Articles

Single-Input Multiple-Output (SIMO) Cascode Low-Noise Amplifier with Switchable Degeneration Inductor for Carrier Aggregation.

This paper presents a single-input multiple-output (SIMO) cascode low-noise amplifier with inductive degeneration for inter- and intra-band carrier aggregation. The proposed low-noise amplifier has two output ports for flexible operation in carrier aggregation combinations for band 30 and band 7. However, during inter- and intra-band operation, gain variation occurs depending on the output mode. To compensate for this, a switching circuit is proposed to adjust the degeneration inductor, optimizing gain performance for both modes. The switching operation can minimize the control for the dynamic range in the receiver system to support carrier aggregation. The designed low-noise amplifier was fabricated using a 65 nm CMOS process, occupying an area of 2.1 mm2. In inter-band operation, the small-signal gain was measured by 18.9 dB for band 30 and 18.6 dB for band 7, with the noise figures of 1.03 dB and 1.07 dB, respectively. For intra-band operation, the small-signal gain was 17.3 dB and 17.2 dB, with the noise figures of 1.3 dB and 1.41 dB. The IIP3 values were measured by -7.6 dBm and -6.7 dBm for inter-band, and -6.3 dBm and -6.2 dBm for intra-band. Power consumption was 8.04 mW and 7.68 mW in inter-band, and 17.04 mW and 17.64 mW in intra-band depending on the output configuration.

Analysis of Optimal Diversity Combining with Imperfect Channel State Information for Cooperative Jamming-Aided Internet of Things Security

Cooperative jamming (CJ) combined with single-input multiple-output (SIMO) technology can effectively improve the security and reliability of Internet of Things (IoT) systems. However, imperfect main channel state information (CSI) leads to incomplete CJ cancellation, which degrades the performance after combining. In this paper, by considering channel estimation errors and residual CJ at each receiving antenna, the residual CJ power after jamming suppression is analyzed, and the optimal combining coefficient for maximizing the signal-to-jamming-noise ratio (SJNR) is derived. The output SJNR of optimal diversity combining is given, and the achievable secrecy rate is analyzed on this basis. The theoretical and simulation results verify the combined effect of channel estimation errors and residual CJ on the combining performance. Moreover, it is worth noting that the combining performance is closely related to the spatial correlation of residual CJ.

Hybrid Beamforming Structure Using Grouping with Reduced Number of Phase Shifters in Multi-User MISO

This paper proposes a novel hybrid beamforming (HBF) structure for gain-aware grouping transmit antennas and users in multiuser multiple-input single-output (MU-MISO) systems. In the conventional HBF structure, all transmit antennas form a beam to each user. In this case, the gain of each antenna varies depending on the location of the base station and each user, and the transmit power after the digital beamformer is allocated to the antenna with the smallest gain. Signals transmitted from antennas with small gains are susceptible to noise and interference. Therefore, this paper proposes an HBF structure in which only the antenna with the highest gain forms the beam for each user. In the proposed scheme, the transmitting antennas are grouped and the beam is formed only by the group of antennas with the highest gain for each user. Simulation results show that the proposed scheme can reduce the number of phase shifters used on the transmit side compared to the conventional HBF scheme while maintaining sum-rate performance when the number of transmit antennas and users are the same. It was also shown that there is a trade-off between the reduction in the number of phase shifters used to form the beam and the improvement in performance as the number of transmit antennas increases. Furthermore, it is shown that when antenna selection is used, although there is a trade-off between the number of phase shifters and performance improvement, the number of phase shifters can be reduced while maintaining performance even when the number of transmit antennas increases.

Global active noise control using SIMO near-field systems - Simulation and technical implementation

The technical implementation of a single-input multiple-output (SIMO) active near-field noise control (ANC) system designed for global low-frequency noise control is presented. The SIMO control strategy is motivated by noise control simulations based on a direct boundary element method (BEM) ansatz formulated in this paper. The suitability of the chosen BEM formulation and SIMO control strategy is accompanied and confirmed by extensive experiments and comparison to analytical calculations based on isotropic sources. The influence of parameters such as the positioning of the error microphone, the membrane velocity required for optimal global reduction, the effects of phase inaccuracies and the number of actuators on global reduction are investigated. The real-time control of the SIMO system is technically implemented on field programmable gate array (FPGA) hardware using a frequency domain block FxLMS algorithm. The iterative algorithm converges in less than 0.1 s for the examined frequency range from 100 Hz to 1000 Hz. Measurements using various circular SIMO array configurations showed reductions in sound power of up to 85\%, aligning closely with the numerical results.

Performance Enhancement for B5G/6G Networks Based on Space Time Coding Schemes Assisted by Intelligent Reflecting Surfaces with Higher Modulation Orders.

Intelligent Reflecting Surfaces (IRS) and Multiple-Input Single-Output (MISO) technologies are essential in the fifth generation (5G) networks and beyond. IRS optimizes the signal propagation and the coverage and is a viable approach to address the issues caused by fading channels that limits the spectral efficiency, while MIMO enhances data rates, reliability, and spectral efficiency by using multiple antennas at both transmitter and receiver ends. This paper proposes an IRS-assisted MISO system using the Orthogonal Space-Time Block Code (OSTBC) scheme to enhance the channel reliability and reduce the Bit Error Rate (BER) in wireless communication systems. The proposed system exploits the benefits from the transmit diversity gain of the OSTBC scheme as well as from the bit energy to noise power spectral density (Eb/No) improvement of the IRS technology. The presented work explores these combined technologies across different modulation schemes. The obtained results outperform the similar previously published works by considering higher-order modulation schemes as well as the deployment of rate ¾ OSTBC-assisted IRS. Moreover, the obtained results demonstrate that the integration of OSTBC with IRS can yield significant performance improvements in terms of Eb/No by 7 dB and 13 dB when using 16 reflecting elements and 64 reflecting elements, respectively.

Fading model due to scintillation and pointing error on an optical wireless MISO channel

Optical wireless communication (OWC) yields high data rates and a license-free spectrum. However, OWC is drastically affected by scintillation owing to atmospheric turbulence and pointing errors because of misalignment. To alleviate the ramifications of scintillation and pointing error, multiple input single output (MISO) optical wireless channels are studied by several researchers. In this paper, it is proposed to study the performance of a MISO system in terms of the probability of outage and normalized threshold. Gamma–Gamma distribution is used to model scintillation because it is suitable for modeling both weak and strong turbulence conditions. The analytical technique is used to derive the closed-form expressions for the probability of outage of a 2×1 MISO channel. Moreover, under numerous scintillation conditions, the Mellin transform is applied to derive the closed-form expressions for the probability of outage of an optical wireless MISO channel. The closed-form results are validated through simulations.

Optoelectronics Interfaces for a VLC System for UHD Audio-Visual Content Transmission in a Passenger Van: HW Design.

This work aims to provide the hardware (HW) design of the optoelectronics interfaces for a visible-light communication (VLC) system that can be employed for several use cases. Potential applications include the transmission of ultra-high-definition (UHD) streaming video through existing reading lamps installed in passenger vans. In this use case, visible light is employed for the downlink, while infrared light is used for the uplink channel, acting as a remote controller. Two primary components -a Light Fidelity (LiFi) router and a USB dongle-were designed and implemented. The 'LiFi Router', handling the downlink channel, comprises components such as a visible Light-Emitting Diode (LED) and an infrared receiver. Operating at a supply voltage of 12 V and consuming current at 920 mA, it is compatible with standard voltage buses found in transport vehicles. The 'USB dongle', responsible for the uplink, incorporates an infrared LED and a receiver optimized for visible light. The USB dongle works at a supply voltage of 5 V and shows a current consumption of 1.12 A, making it well suited for direct connection to a universal serial bus (USB) port. The bandwidth achieved for the downlink is 11.66 MHz, while the uplink's bandwidth is 12.27 MHz. A system competent at streaming UHD video with the feature of being single-input multiple-output (SIMO) was successfully implemented via the custom hardware design of the optical transceivers and optoelectronics interfaces. To ensure the system's correct performance at a distance of 110 cm, the minimum signal-to-noise ratio (SNRmin) for both optical links was maintained at 10.74 dB. We conducted a proof-of-concept test of the VLC system in a passenger van and verified its optimal operation, effectively illustrating its performance in a real operating environment. Exemplifying potential implementations possible with the hardware system designed in this work, a bit rate of 15.2 Mbps was reached with On-Off Keying (OOK), and 11.25 Mbps was obtained with Quadrature Phase Shift Keying (QPSK) using Orthogonal Frequency-Division Multiplexing (OFDM) obtaining a bit-error rate (BER) of 3.3259 × 10-5 in a passenger van at a distance of 72.5 cm between the LiFi router and the USB dongle. As a final addition, a solar panel was installed on the passenger van's roof to power the user's laptop and the USB dongle via a power bank battery. It took 13.4 h to charge the battery, yielding a battery life of 22.3 h. This characteristic renders the user's side of the system entirely self-powered.

Analysis of 27 supervised machine learning models for the co-gasification assessment of peanut shell and spent tea residue in an open-core downdraft gasifier

The producer gas (PG) obtained through thermochemical processing of the various renewable biomass types contributes to Sustainable Development Goal-7 (SDG-7). Hence, this study examined 27 supervised and multiple-input single-output ML models in terms of performance metrics and accuracy to predict CO, H2, CH4, and CO2 compositions, as well as PG's HHV in the co-gasification of peanut shell (PS) and spent tea residue (STR). Multiple trial experiments were tested with various equivalence ratios (ERs) and mixing ratios (MRs) on a 90 m3/h gas-yield open-core, down-draft gasifier with air as the gasification medium. About 18 models were chosen after evaluating their performance metrics in estimating relevant parameters. The accuracy of those models is assessed based on 12 sample runs with varying ER and MR. The findings revealed that 16 models from the linear, neural network, support vector machine, Gaussian process, tree, and ensemble categories were reliable ML models. The chosen 16 models' R2 values for CO, H2, CH4, CO2, and HHVPG are above 0.931, 0.937, 0.962, 0.806, and 0.971, respectively, with the exception of TRE. Additionally, the models demonstrated a prediction accuracy of >95 % for all of the investigated parameters in the co-gasification of PS and STR when compared to random experimental runs.

Data-Aided Maximum Likelihood Joint Angle and Delay Estimator Over Orthogonal Frequency Division Multiplex Single-Input Multiple-Output Channels Based on New Gray Wolf Optimization Embedding Importance Sampling.

In this paper, we propose a new data-aided (DA) joint angle and delay (JADE) maximum likelihood (ML) estimator. The latter consists of a substantially modified and, hence, significantly improved gray wolf optimization (GWO) technique by fully integrating and embedding within it the powerful importance sampling (IS) concept. This new approach, referred to hereafter as GWOEIS (for "GWO embedding IS"), guarantees global optimality, and offers higher resolution capabilities over orthogonal frequency division multiplex (OFDM) (i.e., multi-carrier and multi-path) single-input multiple-output (SIMO) channels. The traditional GWO randomly initializes the wolfs' positions (angles and delays) and, hence, requires larger packs and longer hunting (iterations) to catch the prey, i.e., find the correct angles of arrival (AoAs) and time delays (TDs), thereby affecting its search efficiency, whereas GWOEIS ensures faster convergence by providing reliable initial estimates based on a simplified importance function. More importantly, and beyond simple initialization of GWO with IS (coined as IS-GWO hereafter), we modify and dynamically update the conventional simple expression for the convergence factor of the GWO algorithm that entirely drives its hunting and tracking mechanisms by accounting for new cumulative distribution functions (CDFs) derived from the IS technique. Simulations unequivocally confirm these significant benefits in terms of increased accuracy and speed Moreover, GWOEIS reaches the Cramér-Rao lower bound (CRLB), even at low SNR levels.

Resource allocation for practical phase shift STAR-RIS enabled MISO-NOMA wireless network with non ideal hardware

This study investigates the sum secrecy rate SRsum of a simultaneous transmission and reflection reconfigurable intelligent surface (STAR-RIS)-enabled multiple input single-output (MISO) non-orthogonal multiple access (NOMA) downlink network with non-ideal hardware defects (HWDs) at the transceivers. Earlier STAR-RIS studies assumed an ideal phase shift model, with each element reflect and transmit the signal without regard to its phase shift. The proposed practical phase shift model accounts for the phase-dependent amplitude variation in the reflection and transmission (RAT) coefficients. The goal is to maximize the SRsum through an alternating optimization (AO) iterative algorithm, leverages a classical semidefinite relaxation (SDR) for beamformer vector design (BVD), and employs an interior point method (IPM) to calculate NOMA power allocation factors αt,αr. The analysis focuses on the evaluation of the SRsum in scenarios with eavesdroppers, under the consideration of both ideal and practical phase shift cases. The study examines the impact of different non-ideal HWDs on the SRsum of the system and provides insights into vulnerabilities and limitations arising from these effects.

Verification and Validation of Advanced Control Systems for a Spinal Joint Wear Simulator.

Wear simulation aims to assess wear rates and their dependence on factors like load, kinematics, temperature, and implant orientation. Despite its significance, there is a notable gap in research concerning advancements in simulator control systems and the testing of clinically relevant waveforms. This study addresses this gap by focusing on enhancing the conventional proportional-integral-derivative (PID) controller used in joint simulators through the development of a fuzzy logic-based controller. Leveraging a single-input multiple-output (SIMO) fuzzy logic control system, this study aimed to improve displacement control, augmenting the traditional proportional-integral (PI) tuning approach. The implementation and evaluation of a novel Fuzzy-PI control algorithm were conducted on the Leeds spine wear simulator. This study also included the testing of dailyliving (DL) profiles, particularly from the hip joint, to broaden the scope of simulation scenarios. While both the conventional PI controller and the Fuzzy-PI controller met ISO tolerance criteria for the spine flexion-extension (FE) profile at 1 Hz, the Fuzzy-PI controller demonstrated superior performance at higher frequencies and with DL profiles due to its real-time adaptive tuning capability. The Fuzzy-PI controller represents a significant advancement in joint wear simulation, offering improved control functionalities and more accurate emulation of real-world physiological dynamics.

Secure beamforming design for MISO URLLC networks in IoT applications

This paper investigates joint beamforming and artificial noise (AN) design for secure multiple-input single-output (MISO) ultra-reliable and low latency communication (URLLC) networks in Internet of Things (IoT) applications. In considered system, a base station (BS) transmits confidential information for individual IoT users using the short-packet communication technique under the wiretap of eavesdroppers. To enhance physical layer security, the BS injects additional dedicated AN symbols to degrade the information retrieval ability at eavesdroppers. In this paper, we aim to joint design the transmit beamforming and AN symbol to maximize the minimum URLLC secrecy rate of IoT user subject to the power budget of the BS. The optimization design problem is highly nonconvex due to coupled variables in the URLLC secrecy rate and channel dispersion expressions, and thus it is mathematically challenging to solve this problem directly. To overcome this issue, we first introduce various convex inner approximations to convexify the nonconvex terms, and then we develop an efficient iterative algorithm based on the sequential convex programming approach. Extensive numerical simulation results are conducted to investigate the URLLC secrecy rate region. In conclusion, the two new URLLC parameters, i.e., the transmit packet blocklength and block error probability, will cause the considerable degradation on the URLLC secrecy rate region when comparing to that of the traditional beamforming design based on the Shannon capacity.

Development of a High-Sensitivity Millimeter-Wave Radar Imaging System for Non-Destructive Testing.

There is an urgent need to develop non-destructive testing (NDT) methods for infrastructure facilities and residences, etc., where human lives are at stake, to prevent collapse due to aging or natural disasters such as earthquakes before they occur. In such inspections, it is desirable to develop a remote, non-contact, non-destructive inspection method that can inspect cracks as small as 0.1 mm on the surface of a structure and damage inside and on the surface of the structure that cannot be seen by the human eye with high sensitivity, while ensuring the safety of the engineers inspecting the structure. Based on this perspective, we developed a radar module (absolute gain of the transmitting antenna: 13.5 dB; absolute gain of the receiving antenna: 14.5 dB) with very high directivity and minimal loss in the signal transmission path between the radar chip and the array antenna, using our previously developed technology. A single-input, multiple-output (SIMO) synthetic aperture radar (SAR) imaging system was developed using this module. As a result of various performance evaluations using this system, we were able to demonstrate that this system has a performance that fully satisfies the abovementioned indices. First, the SNR in millimeter-wave (MM-wave) imaging was improved by 5.4 dB compared to the previously constructed imaging system using the IWR1443BOOST EVM, even though the measured distance was 2.66 times longer. As a specific example of the results of measurements on infrastructure facilities, the system successfully observed cracks as small as 0.1 mm in concrete materials hidden under glass fiber-reinforced tape and black acrylic paint. In this case, measurements were also made from a distance of about 3 m to meet the remote observation requirements, but the radar module with its high-directivity and high-gain antenna proved to be more sensitive in detecting crack structures than measurements made from a distance of 780 mm. In order to estimate the penetration length of MM waves into concrete, an experiment was conducted to measure the penetration of MM waves through a thin concrete slab with a thickness of 3.7 mm. As a result, Λexp = 6.0 mm was obtained as the attenuation distance of MM waves in the concrete slab used. In addition, transmission measurement experiments using a composite material consisting of ceramic tiles and fireproof board, which is a component of a house, and experiments using composite plywood, which is used as a general housing construction material in Japan, succeeded in making perspective observations of defects in the internal structure, etc., which are invisible to the human eye.

Dentists who can auscultate: Microphone-based toothbrushing quality monitoring system for electronic toothbrush

Tooth brushing is a widely recognized and effective method for daily oral care. However, the lack of real-time feedback for monitoring the brushing process can hinder individuals in maintaining their oral hygiene. Currently, only high-end electric toothbrushes offer evaluation functions based on built-in sensors, making them unaffordable for the majority of people. In this paper, we propose a novel and cost-effective wearable acoustic-based system (both hardware and software) for monitoring the quality of daily tooth brushing. Our system combines a throat-microphone and a Bluetooth earphone to capture brushing noises, which are unique acoustical signals generated from the air and the human body during tooth brushing, respectively. By leveraging the distinctive characteristics of brushing sounds in these two different conductive media, we introduce an intelligent detection algorithm based on Single-Input Multiple-Output (SIMO) modeling and frequency response functions (FRFs) to detect the corresponding brushing area. Through experimentation, we have found that the divergence of FRFs provides more stable features compared to general statistical features used in previous studies. After comparing various machine learning algorithms, we have selected XGBoost as the final detection model. Additionally, we utilize the Symmetric Nearest Neighbor (SNN) filter in the post-processing stage to further reduce the jitter noise in continuous detection. The final system achieves an average precision of 98.46% when tested on tooth brushing data collected from different volunteers. To enhance user experience, we have developed an Android App with a user-friendly interface that incorporates the detection system. With a total wearable hardware cost of less than 10 dollars, our system shows great potential for integration into future smart wearable devices.

Multi‐band millimetre wave indoor directional channel measurements and analysis for future wireless communication systems

AbstractSingle‐input single‐output (SISO) three‐dimensional (3D) wideband indoor directional measurements collected in a factory environment and an office environment at 38 and 70 GHz are presented. 3D single‐input multiple‐output (SIMO) dual polarised measurements with 1 × 2 antenna configurations were also carried out in a meeting room, a conference room, and an office room at the 60 GHz band. The measurements cover both azimuth and elevation by rotating the directional antenna (RDA) at the receiver side. Different statistical channel parameters such as power delay profile, power angle profile, root‐mean‐square delay spread, angular spread, and path loss were estimated for different possible antenna orientations between the transmitter and the receiver, which include line‐of‐sight, obstructed line‐of‐sight, and non‐line‐of‐sight. The polarisation effects on path loss models and the delay and angular spread models based on the surface area of the environment are studied. The results will be valuable for the design of indoor millimetre wave cellular networks.

User Scheduling and Path Planning for Reconfigurable Intelligent Surface Assisted MISO UAV Communication

The high mobility of unmanned aerial vehicles (UAVs) enables them to improve system throughput by establishing line-of-sight (LoS) links. Nevertheless, in urban environments, these LoS links can be disrupted by complex urban structures, leading to potential interference issues. Reconfigurable intelligent surfaces (RIS) provide an innovative approach to enhance communication performance by intelligently reflecting incident signals. Recent studies suggest that utilizing multi-antenna transmission can increase system efficiency, while single-antenna transmission may be more prone to interference. To address these challenges, this article introduces a RIS-assisted multiple-input single-output (MISO) UAV communication system. Our objective is to optimize the minimum user rate, thereby guaranteeing equitable communication for all users. Nevertheless, the non-convexity inherent in this optimization problem complicates the pursuit of a direct solution. Hence, we decompose the problem into four subproblems: user scheduling optimization, RIS phase-shift optimization, UAV trajectory optimization, and UAV transmit beamforming optimization. To obtain suboptimal solutions, we have developed an alternating iterative optimization algorithm for addressing the four subproblems. Numerical results demonstrate that our algorithm effectively boosts the minimum user rate of the entire system.

Vibration-based Damage Diagnosis for a Population of Composite Structures Under Uncertainty via Hyper-Sphere and Transfer Component Analysis Based Methods

The problem of vibration-based damage diagnosis, including the detection and type characterization of damages in a population of nominally identical composite structures under operational uncertainty is investigated. This is an important problem for various types of fleets, such as aircraft, drones, fixed wing UAVs and others, which becomes highly challenging if the variability in the composite materials and the manufacturing of the population is significant, while the diagnosis of early-stage damages is pursued. Such a population of 27 composite coupons subjecting to operating variability due to alterations in the temperature, the excitation and the experimental setup is considered in this study. Furthermore, early-stage delamination and impact-induced damages are implemented in 10 of the coupons. Damage diagnosis is herein attempted via two data-driven methods that may account for various types of uncertainty, which are founded on a number of stochastic Multiple-Input Single-Output Transmittance Function AutoRegressive with eXogenous pseudo-eXcitation (MISO-TF-ARX) models. The first employs Hyper Spheres for the representation of the healthy subspace under uncertainty using the parameters of the MISO-TF-ARX models and thus abbreviated as HS-MISO-TF, while the other is based on the Transfer Component Analysis of these parameters, abbreviated as TCA-MISO-TF. The methods’ damage diagnosis performance is experimentally assessed using the above composite coupons and a high number of 7 500 inspection test cases for damage detection, whereas damage characterization is based on 450 test cases. The damage detection and characterization results are presented through Receiver Operating Characteristics curves and confusion matrices, respectively. The obtained results indicate adequate damage detection with the HS-MISO-TF method to achieve 82.1% correct detection for 5% of false alarms, with the TCA-MISO-TF following with 76.4% correct detection. Damage characterization is remarkable with the HS-MISO-TF to correctly characterizing the considered damage type for the 100% of the considered test cases and the TCA-MISO-TF following with 92.2%.

Vibration-Based Railway Suspension Monitoring Under Varying Operating Conditions via Robust Statistical Time Series Type Methods

The on-board condition monitoring of railway suspension components is important for ensuring passenger comfort, maintaining proper operation, enhancing safety, and reducing operational costs. In this context statistical time series type random-vibration-based methods constitute a potentially efficient and cost-effective framework. Yet a significant challenge emerges from the competing requirements for high sensitivity to suspension component degradation and robustness to varying Operating Conditions (OCs) and uncertainty. Varying Operating Conditions and uncertainty are related to factors such as varying payload, travelling speed, and rail profile. The problem is further aggravated by the complexity of the vehicle dynamics, including the wheelbase filtering effect. Despite the significant progress made so far and the development of various methods, the challenges related to varying OCs and uncertainty largely remain as a technical barrier. The aim of the present study is the introduction of a data-based methodology aspiring to overcome them. The methodology is based on Multiple-Input Single-Output Transmittance Function (MISO-TF) time series models of a special form allowing for eliminating the effects of varying rail profile while properly treating the wheelbase filtering effect. Monitoring is based on a MISO-TF feature space, using either a Random Coefficient Gaussian Mixture or a Multiple Model based scheme. The former, although more elaborate, allows for the introduction of a complete probabilistic framework. An interesting advantage of both versions is that operation can be based on a very limited number of sensors and only a partial data-driven model of the dynamics. The methodology is comprehensively assessed via hundreds of SIMPACK based Monte Carlo runs under variable payload and rail profiles. The achievable performance is shown to be very good for both versions and for 10%, 15%, and 20% of condition degradation in either primary or secondary suspension components.

Integrated Mobile Visible Light Communication and Positioning Systems Based on Decision Feedback Channel Estimation

Visible light communication (VLC) and visible light positioning (VLP) systems are usually designed separately to prevent mutual interference, while terminal mobility often introduces challenges that can degrade their performance. In this paper, we propose an integrated visible light communication and positioning (VLCP) scheme designed for mobile scenarios, encompassing both multiple-input–single-output (MISO) and multiple-input–multiple-output (MIMO) configurations. This scheme integrates both functionalities into a unified system. Utilizing decision feedback channel estimation (DFCE), we effectively estimate the dynamic channel state information (CSI) for both VLC and VLP, thereby potentially enhancing both communication and positioning performance. Simulation results across various routes verify the effectiveness of the proposed scheme. It is observed that when the terminal moves at 1 m/s, the VLCP scheme with DFCE can maintain reliable transmission quality, ensuring bit error rates (BERs) consistently below 1.3 × 10−2. Additionally, the mean positioning errors remain within the centimeter range in different routes, not exceeding 4.3 cm and 15.5 cm in the MISO and MIMO scenarios, respectively.

Performance analysis of hybrid combining schemes under Middleton class‐A and SαS${\rm S}\alpha{\rm S}$ impulsive noise model

AbstractImpulsive noise poses a significant challenge to single input multiple output wireless communication systems. This paper assesses the effectiveness of hybrid combining techniques, namely selection combining‐equal gain combining and selection combining‐maximal ratio combining, in mitigating impulsive noise impact caused by both man‐made and natural phenomena. The evaluation considers three different noise models: Additive white Gaussian noise, Middleton class‐A impulsive noise, and symmetric alpha stable impulsive noise, across Rayleigh and Rician fading channels. Bit error rate is employed to gauge channel performance. Our research contribution lies in the comprehensive assessment of hybrid combining techniques under diverse noise models, addressing a critical research gap in wireless communication. Findings indicate that impulsive noise has a more pronounced impact on channel performance than additive white Gaussian noise, and hybrid combining techniques prove more effective in mitigating these effects. The results hold significant implications for single input multiple output wireless communication systems, guiding the development of more robust and reliable communication systems in impulsive noise scenarios.